LIST OF APPROVED CLAMPS AND MOUNTING SYSTEMS FOR MODULES OF THE SL2 AND SL2-F SERIES

Transcription

1 Page 1 When mounting Solibro modules from generation G1.4 or higher with the specified clamps, section 2 "Planning" of the valid installation and operation manual under: 2.2 "Requirements on the clamp system for unframed modules" 2.2 "Requirements on the clamp system for framed modules" 2.3 "Mounting options" must be observed. The use of clamping systems which are not approved by Solibro can result in modules breaking, which in turn can cause electrical hazards that represent a danger to life and limb and a risk of material damage! CLAMPS FOR UNFRAMED MODULES [SL2] SOLIBRO CLAMP - SC1 (120 mm) : Alumero Middle and are identical (black) SL2 Point mounting Pressure load 1600 Pressure load 2400 Use a minimum rail width of Torque: Nm SOLIBRO CLAMP - SC2 (120 mm) : Alumero Middle clamp (black) (black) SL2 Point mounting Pressure load 1600 Pressure load 2400 Use a minimum rail width of Torque:10-18 Nm The required clamping force can be found in the manufacturer information. The fixing screws must be aligned with the substructure rails.

2 Page 2 CLAMPS WITH GROUNDING FUNCTION FOR FRAMED MODULES [SL2-F] ALUMERO (50 mm) : Alumero without screw (black) without screw (black) Grounding plate ALUMERO (50 mm) : Alumero with screw (black) with screw (black) Grounding plate ESDEC BV (40 mm) : Esdec (black) (black) SL2-F Point mounting Pressure load 3600 Pressure load 5400 Clamps and screws should only be used as a system with Esdec substructure rails.

3 Page 3 HATICON (40/35 mm) : HatiCon with grounding clip AK II Klick AK II Klick AK II Klick (black) Haticon substructure rails. HILTI MSP-PR-EC (50 mm) : Hilti with grounding plate MSP-PR-MC black MSP-PR-MC MSP-PR-EC black MSP-PR-EC Hilti substructure rails. MOUNTING SYSTEMS (40/35 mm) : Mounting Systems (black) Grounding clip Mounting Systems substructure rails.

4 Page 4 SCHLETTER (100 mm) : Schletter (black) Grounding end clamp (black) For black anodized clamps, a screw with locking serration must be used. SCHLETTER (100 mm) : Schletter Rapid 2+ substructure rails. SUNFIXINGS (70 mm) : Sunfixings with grounding disc

5 Page 5 SUPORTS (50 mm) : Suports OS2 ZS2 SL2-F Point mounting Pressure load 3600 Pressure load 5400 Use a minimum rail width of

6 Page 6 MOUNTING SYSTEMS FOR UNFRAMED MODULES [SL2] SOLIBRO Name of system Type of application Solibro Slide-In Free field Detachedly elevated system Permitted inclination Notice 2,000 Pa 3,000 Pa Mounting on a separate substructure The currently valid installation manual for the Solibro Slide-In System must be applied for the installation. The requirements of the substructure can be requested from the respective manufacturer. SUNBEAM Name of system Sunbeam Sunbeam symmetrical Type of application Flat roof with the max. inclination of 5 Elevated system Mounting inclination 2 x 10 Type of roof** Roof connection** 1,600 Pa 2,400 Pa Flat roof: foil and bitumen roof Flat roof: ballasting * * Mounting according to the manufacturer s specification and the structural analysis CALYXO Name of system Type of application Type of roof** Roof connection** Calyxo MX Flat roof, tilted roof Parallel to the roof 2,000 Pa 3,000 Pa Flat roof: foil and bitumen roof Tilted roof: tile and metal roof Flat roof: ballasting Tilted roof: roof penetration * * Mounting according to the manufacturer s specification and the structural analysis

7 Page 7 MOUNTING SYSTEMS FOR FRAMED MODULES [SL2-F] K2 K2 Systems Name of system Dome D 800 Type of application Flat roof with the max. inclination of 5 Elevated system Mounting inclination 2 x 10 Type of roof** Roof connection** 2,000 Pa 3,000 Pa Flat roof: foil and bitumen roof Flat roof: ballasting * * Mounting according to the manufacturer s specification and the structural analysis Subject to alterations. Solibro GmbH List of approved clamps and mounting systems_sl2_ _rev15_en SOLIBRO GMBH OT Thalheim, Sonnenallee Bitterfeld-Wolfen, Germany WEB service@solibro-solar.com