SPANISH TILE INSTALLATION DETAILS BERRIDGE MANUFACTURING COMPANY

Transcription

1 SPANISH TILE INSTALLATION DETAILS

2 INDEX INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INTRODUCTION TO TYPICAL DETAILS OVERVIEW PANEL SPLICE DETAIL PANEL SPLICE DETAIL OVER OPEN RAMING INSULATED DECK DETAIL EAVE DETAIL EAVE DETAIL OVER OPEN RAMING RIDGE/HIP DETAIL RIDGE/HIP DETAIL OVER OPEN RAMING GABLE AT RIDGE DETAIL SHED ROO RIDGE CAP DETAIL GABLE DETAIL GABLE DETAIL GABLE DETAIL PARAPET DETAIL HEAD WALL DETAIL RAKE WALL DETAIL HEAD WALL DETAIL RAKE WALL DETAIL SLOPE TRANSITION DETAIL VALLEY LASHING DETAIL VALLEY ISOMETRIC DETAIL VALLEY DETAIL OPEN RAMING CONDITION ROO PENETRATION - ROUND DETAIL - PREERRED METHOD ROO PENETRATION ROUND ROO PENETRATION ROUND (SECTION) ROO PENETRATION - RECTANGULAR/SQUARE ROO PENETRATION SECTION - A ROO PENETRATION SECTION - B ROO PENETRATION ISOMETRIC ROO PENETRATION OPEN RAMING CONDITION ST-0 STI-1 STI-2 STI-3 STI-4 STI-5 ST-1 ST-2 ST-3 ST-4 ST-5 ST-10 ST-11 ST-20 ST-21 ST-22 ST-23 ST-30 ST-31 ST-32 ST-40 ST-50 ST-51 ST-52 ST-53 ST-60 ST-70 ST-71 ST-72 ST-80 ST-81 ST-82 ST-83 ST-84 ST-85 ST-86 ST-87 INDEX ST-0

3 A. B. C. SPANISH TILE: IS COMPOSED O INTERLOCKING BARREL TILES ON DEEP VEE PANELS WITH RIB SPACING AT 9" O.C. MINIMUM SLOPE: THE SPANISH TILE SYSTEM IS RECOMMENDED OR SLOPES O 2 ON 12 AND GREATER. A DOUBLE LAYER O NUMBER THIRTY ELT UNDERLAYMENT OR EQUAL IS RECOMMENDED OR ALL APPLICATION WHERE THE ROO SLOPE IS 3 ON 12 OR LESS. MATERIAL STORAGE: CAUTION MUST BE EXERCISED IN STORAGE O MATERIALS PRIOR TO INSTALLATION. KEEP ALL PREINISHED MATERIAL IN A DRY LOCATION WITH ADEQUATE VENTILATION AND OUT O DIRECT SUNLIGHT. D. E. STRIPPABLE ILM: THE STRIPPABLE PLASTIC ILM WHICH IS APPLIED OVER MOST PREINISHED PRODUCTS, PANELS, LASHINGS, COILS AND LAT SHEETS PROVIDES PROTECTION O THE INISH DURING ABRICATION AND TRANSIT. THIS ILM MUST BE REMOVED PRIOR TO INSTALLATION. SOLID SHEATHING REQUIREMENTS: RECOMMENDS THE USE O EITHER 24 GAUGE CORRUGATED SHEATHING (NOMINAL 2 1/2" PITCH 11/16" DEPTH) OR A MINIMUM O 1/2" SOLID WOOD SHEATHING TO PROVIDE SUICIENT HOLDING POWER OR ASTENERS. CONTACT S' ENGINEERING DEPARTMENT OR USE O ANY OTHER TYPE O SOLID SHEATHING. DUE TO NUMBER THIRTY ELT TENANCY TO TEAR WHEN USED OVER CORRUGATED DECKING, RECOMMENDS GRACE ICE AND WATERSHIELD OR EQUAL TO BE USED AS AN UNDERLAYMENT OR ALL CORRUGATED DECKS.. G. SHEATHING INSPECTION: 1. SHEATHING END JOINTS SHOULD BE STAGGERED. 2. ALL END JOINTS SHOULD MEET AT EITHER A JOIST OR RATER. 3. BLOCKING OR "H" CLIPS SHOULD BE USED O JOINTS DO NOT REMAIN LAT UNDER THE WEIGHT O WORKMEN. 4. USE SHIMS TO JEEP ENTIRE SUBSTRATE EVEN. UNEVEN SUBSTRATE WILL RESULT IN "OIL- CANNING" IN PANELS. SUBSTRATE SHOULD BE LEVEL TO 1/4" IN 20'-0". 5. ALL CUTS AT PENETRATIONS SHOULD BE TIGHT, WITHOUT GAPS. 6. USE WOOD-RAMED CRICKETS AT LARGE PENETRATIONS. 7. MAKE SURE SUBSTRATE JOINTS ARE TIGHT AT ALL HIPS, VALLEYS AND RIDGES. INSTALLATION OVER OPEN RAMING: 1. PURLIN SPACING MUST COMPLY WITH LOAD CHART SHOWN ON PAGE STI-5 AND ALL APPLICABLE CODES AND SPECIICATION REQUIREMENTS. 2. DIAPHRAGM CAPABILITIES AND PURLIN STABILITY ARE MINIMAL AS PROVIDED BY THE SPANISH TILE SYSTEM. THEREORE, OTHER BRACING MAY BE REQUIRED TO CONORM TO A.I.S.C. SPECIICATIONS. INSTALLATION INSTRUCTIONS STI-1

4 H. I. J. OPEN RAMING INSPECTION: 1. PURLINS SHOULD BE ALIGNED WITH TOP LANGES IN THE SAME PLANE TO A TOLERANCE O 1/4" ON 20'-0". UNEVENNESS IN THE TIP PLANE O THE PURLINS WILL RESULT IN ABNORMAL "OIL-CANNING" O PANELS. 2. DO NOT APPLY ON OPEN RAMING AT VALLEYS OR ROO PENETRATIONS WITH OUT REERRING TO DETAILS ON PAGES ST-72 AND ST OOT TRAIC ON THE PANELS MUST BE KEPT TO A MINIMUM. ARCHITECTURAL PANELS ARE DESIGNED OR AESTHETICS AND CAN BE EASILY DAMAGED OR DEORMED IS EXTREME CARE IS NOT USED. ASCIA/RAKE INSPECTION: 1. STRIKE A LINE THE ULL LENGTH O THE ASCIA OR RAKE. I NOT STRAIGHT, CORRECT WITH SHIMS. 2. MAKE SURE ASCIA/RAKE IS LUSH WITH SHEATHING. ELT UNDERLAYMENT: A SINGLE LAYER O NUMBER THIRTY ELT UNDERLAYMENT (OR EQUAL) MUST BE APPLIED OVER SOLID SHEATHING AS SHOWN IN THE TYPICAL ELTING DETAIL. THE USE O ADDITIONAL LAYERS O NUMBER THIRTY ELT IS RECOMMENDED ON LOW SLOPED ROOS, AT ALL VALLEY CONDITIONS, AT ROO PENETRATIONS AND CERTAIN OTHER LASHING CONDITIONS AS DEPICTED IN THE SPANISH TILE TYPICAL DETAILS. GRACE ICE AND WATERSHIELD MAY BE REQUIRED ON LOW SLOPED ROOS OR AT CERTAIN LASHING CONDITIONS. K. L. M. ELTING INSTALLATION: 1. DO NOT USE RED ROSIN PAPER UNDER METAL ROOING PANELS. 2. SWEEP ROO AREA CLEAN. 3. USE LAT HEAD GALVANIZED ROOING NAILS 1 1/4" LONG WITH GALVANIZED ELT CAPS. 4. INSTALL VALLEY ELT IRST. 5. INSTALL ELT PARALLEL TO THE EAVE, (2 LAYERS REQUIRED AT EAVE) STARTING AT EAVE AND USING MINIMUM 6" LAPS. USED 2 LAYERS O ELT ON ENTIRE ROO DECK I ROO SLOPE IS 3 ON 12 OR LESS. 2 LAYERS REQUIRED AT EAVE REGARDLESS O SLOPE. 6. REER TO ELTING DETAILS WHEN VALLEY OR ROO PENETRATIONS ARE INVOLVED ON OPEN RAMING CONDITIONS. 7. INSULATE BETWEEN WOOD BLOCKING AND METAL WITH ELT OR GRACE ICE AND WATERSHIELD. ELECTROLYSIS: AVOID ALLOWING LASHINGS AND PANELS TO COME INTO CONTACT WITH EITHER LEAD OR COPPER AND PREVENT EXPOSURE TO WATER RUNDOWN ROM COPPER AND/ OR LEAD. SEALANT RECOMMENDATIONS: TREMCO, INC. SPECTREM 1 SILICONE SEALANT. DO NOT USE CLEAR CAULK INSTALLATION INSTRUCTIONS STI-2

5 N. LASHING: I IS TO SUPPLY LASHING, ALL LASHINGS WILL BE ABRICATED IN 10'-0" LENGTHS WITH SQUARE END CUTS ONLY. THE PURCHASER MUST PROVIDE ALL DIMENSIONS AND DEGREE O ANGLES. LASHING INSTALLATION: 1. REMOVE STRIPPABLE PLASTIC ILM ROM ALL LASHINGS PRIOR TO INSTALLATION. 2. ALWAYS STAGGER JOINTS WHEN ONE LASHING IS INSTALLED OVER OTHER LASHINGS. 3. INSTALL ALL LASHINGS AS PER TYPICAL DETAILS. 4. ALL LASHINGS ARE TO BE DESIGNED AND INSTALLED TO NOT TRAP WATER. O. P. Q. R. S. PANELS: WILL PROVIDE SQUARE END CUTS ONLY ON ALL DEEP VEE PANELS. COMPUTATION O ALL QUANTITIES AND DIMENSIONS ARE THE RESPONSIBILITY O THE PURCHASER. PANEL INSTALLATION: 1. REMOVE STRIPPABLE PLASTIC ILM ROM EACH DEEP VEE PANEL PRIOR TO INSTALLATION. 2. DETERMINE CENTER LINE O ROO AREA AND START PANEL INSTALLATION AT THE CENTER O THE ROO, WORKING TOWARD THE GABLE ENDS. MAKE SURE PANELS ARE PERPENDICULAR TO THE EAVE. AT VALLEY AREAS, MAKE SURE PANELS ARE INSTALLED SO THAT WATER HAS REE LOW AND IS NOT OBSTRUCTED BY PANEL RIBS. 3. COPPER-COTE, ZINC-COTE, PREWEATHERED GALVALUME AND CHAMPAGNE PANEL INSTALLATION: NOTE THE SERIES O ARROWS PAINTED ON THE UNDER SIDE O THE PANEL. ALL PANELS MUST BE INSTALLED IN A CONSISTENT MANNER, MEANING THAT THE ARROWS ON EVERY PANEL ARE ALL POINTING IN THE SAME DIRECTION. I A PANEL IS REVERSED (ARROWS POINTING OPPOSITE O THOSE ON OTHER PANELS) IT WILL APPEAR, ROM A DISTANCE, A DIERENT SHADE TO THE GRANULAR EECT O THE PIGMENT IN THE INISH. METALLIC INISHED ARE MATCH-LOT INISHED. DO NOT MIX LOTS. SPANISH TILES: ARE ACTORY ABRICATED 17" LONG AND 8" WIDE INTERLOCKING BARREL TILES. SPANISH TILE INSTALLATION: 1. REMOVE STRIPPABLE PLASTIC ILM ROM EACH TILE PRIOR TO INSTALLATION. 2. IN MOST CASES, TILES MAY BE INSTALLED ATER ALL PANELS ARE INSTALLED. 3. WHEN THE PANELS ARE INSTALLED OVER OPEN RAMING AND OR STEEP ROO SLOPES, IT IS RECOMMENDED THAT THE TILES BE INSTALLED AT THE SAME TIME AS THE PANELS. 4. EACH TILE INTERLOCKS WITH THE TILE BELOW IT AS YOU WORK UP THE ROO. THE TILE LAPS AT INTERLOCK IS ADJUSTABLE ROM A MINIMUM O 1" TO A MAXIMUM O 4". ALL TILE LAPS MUST BE THE SAME THOUGHT O THE INSTALLATION OR AN AESTHETICALLY PLEASING INSTALLATION. ASTENERS: INSTALL ASTENERS AS PER TYPICAL DETAILS. USE A 3 1/2" LONG GALVANIZED RING SHANK NAIL OR INSTALLATION O DEEP VEE PANEL OVER WOOD SHEATHING AND USE # X 3" SMS OR INSTALLATION O DEEP VEE PANEL TO METAL. INSTALLATION INSTRUCTIONS STI-3

6 OPTIONAL ATTACHMENT O DEEP VEE PANEL. USE A HEX HEAD ASTENER WITH A METAL BACKED NEOPRENE WASHER, SHEET METAL OR WOOD SCREW (1) EACH SIDE O PANEL RIB THROUGH PANEL PAN. ASTENERS TO BE SIZED TO MEET LOAD REQUIREMENTS. INTERLOCKING SPANISH TILES SHALL BE ATTACHED TO THE TOP O THE RIB ON THE DEEP VEE PANEL WITH # 8 TEK SCREWS. WHEN SURE ALL ASTENERS ARE DRIVEN STRAIGHT AND SET LAT. DO NOT OVERDRIVE ASTENERS, AS THIS WILL CAUSE THE DEEP VEE PANEL, SPANISH TILE AND/OR LASHINGS TO BUCKLE OR BECOME RECESSED BELOW THE ELEVATION O THE SUBSTRATE. (NOTE: I LOCAL CODES OR OTHER REGULATIONS DICTATE SPECIIC WIND UPLIT REQUIREMENTS, CONSULT THE ENGINEERING DEPARTMENT, AS IT MAY BE NECESSARY TO USE A DIERENT ASTENER OR ASTENER SPACING). CONSULT S' ENGINEERING DEPARTMENT REGARDING THE USE O ANY OTHER TYPE O ASTENER. STRIVES TO PROVIDE ITS CUSTOMERS WITH THE HIGHEST QUALITY STRETCHER LEVELED STEEL AVAILABLE. THE LATEST TECHNOLOGY IS ALSO INCORPORATED IN 'S HIGH-PRECISION COIL HANDLING AND ROLL ORMING EQUIPMENT TO MINIMIZE THE STRESS ON METAL DURING PRODUCTION. URTHERMORE, UTILIZES HEAVIER 24 GAUGE METAL RATHER THAN 26 GAUGE STEEL TO LIGHT GAUGE ALUMINUM AS OERED BY MANY COMPETITORS. ALL THESE MEASURES HAVE BEEN TAKEN TO MINIMIZE THE AMOUNT O "OIL0CANNING" (WAVINESS) WHICH IS NATURALLY INHERENT IN LAT SHEET METAL. MANY TIMES, HOWEVER, THE CAUSE O WAVINESS OR "OIL-CANNING" CAN BE TRACED TO UNEVEN SHEATHING, IMPROPER ELT INSTALLATION OR, IN THE CASE O OPEN RAMING, UNEVENNESS O THE TOP PLANE O THE PURLINS OR OOT TRAIC ON THE PANELS. ALL ARCHITECTURAL PANELS REQUIRE CARE IN HANDLING AND INSTALLATION TO AVOID DAMAGING OR DEORMING THE PANELS. THESE INSTALLATION INSTRUCTIONS AND THE OLLOWING TYPICAL DETAILS ARE INTENDED TO PROVIDE OUR CUSTOMERS WITH THE INORMATION REQUIRED OR AN AESTHETICALLY PLEASING AND UNCTIONAL INSTALLATION O THE SPANISH TILE SYSTEM. NOTE: ALL PRODUCT SPECIICATIONS, DETAIL AND INSTALLATION INSTRUCTIONS SUBJECT TO CHANGE WITHOUT NOTICE. OR SPECIIC PROJECT DETAILS, CONTACT. INSTALLATION INSTRUCTIONS STI-4

7 SECTION PROPERTIES BASED ON 24 GAUGE 40 KSI SPANISH TILE dl X (In 4 /ft) M A (t-lbs/t) V A (LBS) POSITIVE BENDING NEGATIVE BENDING Properties are effective and are Per oot of panel coverage. Based on 1986 AISI COLDORM STEEL DESIGN MANUAL, March 1987, and Rational Analysis. Design Thickness = in. RECOMMENDED LOAD IN POUNDS PER SQUARE OOT (PANEL WEIGHT = 1.3 PS) SPAN (T) NET VERTICAL LIVE LOAD NET VERTICAL WIND UPLIT 1-SPAN 2-SPAN 3-SPAN 1-SPAN 2-SPAN 3-SPAN 2'-0" '-6" '-0" '-6" '-0" '-6" '-0" '-0" 7'-0" 1. ALL LOADS MEET L/240 DELECTION CRITERIA 2. WIND LOAD ALLOWABLE STRESSES INCREASED BY 33% INSTALLATION INSTRUCTIONS STI-5

8 THE DETAILS CONTAINED IN THE OLLOWING PAGES ARE MERELY RECOMMENDATIONS AS TO HOW MATERIALS SHOULD BE INSTALLED. THEY MAY REQUIRE ADAPTATIONS OR MODIICATIONS OR A SPECIIC PROJECT AS CONDITIONS VARY IN BOTH BUILDING DESIGN AND LOCAL WEATHER PECULIARITIES. SHALL BE HELD HARMLESS ROM ANY AND ALL CLAIMS ARISING ROM A LACK O WATERTIGHTNESS AS A RESULT O OLLOWING THESE RECOMMENDED DETAILS. ENSURING WATERTIGHTNESS ON ANY GIVEN PROJECT IS THE UNCTION O THE INSTALLER. THE ARCHITECT/GENERAL CONTRACTOR/INSTALLER MUST ACCEPT THE RESPONSIBILITY TO ADAPT THESE DETAILS TO MEET PARTICULAR BUILDING REQUIREMENTS AND TO ASSURE ADEQUATE WATERTIGHTNESS. THE INSTALLER CAN VIRTUALLY ASSURE WATERTIGHTNESS I THESE LASHING DETAILS HAVE BEEN PROPERLY ADAPTED, ADEQUATE LAPS HAVE BEEN PROVIDED, CORRECT TYPE O SEALANT USED, ALL JOINTS ADEQUATELY CAULKED AND PROESSIONAL WORKMANSHIP EMPLOYED. INTRODUCTION TO TYPICAL DETAILS ST-1

9 SPANISH TILE 16" EAVE CLOSURE ASTEN TILE TO RIB O DEEP VEE PANEL ASTENERS 20" O.C. MAX. OR AT EACH PURLIN DEEP VEE PANEL OPTIONAL ASTENER LOCATION IN PAN O PANEL (1) ASTENERS EACH SIDE O RIB. ASTENERS TO HAVE A METAL BACKED NEOPRENE WASHER. 9" 1 1/2" EAVE CLOSURE DEEP VEE PANEL SECTION SPANISH TILE DEEP VEE PANEL 17" EAVE CLOSURE PANEL ASSEMBLY SECTION 8" 1" SPANISH TILE SECTION OVERVIEW ST-2

10 Deep Vee Panel astener irst Tile Step 1: Install first tile at eave and fasten to rib of Deep Vee Panel irst Tile lange Tile Ribs Second Tile Step 4: With second hand push down to engage this tile on to the first tiles flange, some force will be required to POP this tile into place Step 2: Elevate second tile over first and engage one side on to flange of first tile, keep end of tile below tile ribs. Remember to remove strippable plastic film from Deep Vee panel and prior to installation. Tile installed properly will fit tight on to lower tiles, do not trim off edges of tile flange. Step 3: Keeping palm of one hand as shown and lower other side of tile OVERVIEW ST-2.1

11 DEEP VEE PANEL UPPER PANEL (2) CONTINUOUS BEADS O CAULK NEST UPPER PANEL INTO LOWER PANEL LOWER PANEL DEEP VEE PANEL ASTENER AT PANEL RIB (2) CONTINUOUS BEADS O CAULK 10" MIN. LAP # 30 ELT UNDERLAYMENT SOLID SHEATHING PANEL LAP DETAIL ST-3

12 DEEP VEE PANEL UPPER PANEL (2) CONTINUOUS BEADS O CAULK NEST UPPER PANEL INTO LOWER PANEL LOWER PANEL DEEP VEE PANEL ASTENER AT PANEL RIB (2) CONTINUOUS BEADS O CAULK 10" MIN. LAP PURLIN ALL PANEL LAPS TO BE MADE AT PURLINS PANEL LAP DETAIL OVER OPEN RAMING ST-4

13 SPANISH TILE SYSTEM INSULATING MATERIAL CORRUGATED METAL DECK CONTINUOUS ZEE PURLIN # 30 ELT UNDERLAYMENT ASTENER AT EVERY PURLIN SEE NOTE # 3 STRUCTURAL MEMBER # 30 ELT UNDERLAYMENT SEE ZEE PURLIN DETAIL BELOW 1. ALL ELT UNDERLAYMENT, STRUCTURAL MEMBERS, CORRUGATED METAL DECK AND INSULATING MATERIAL ARE ITEMS TO BE URNISHED AND INSTALLED BY OTHERS AT THE DISCRETION OR THE ARCHITECT. 2. CONTINUOUS WOOD BLOCKING (BY OTHERS) MAY BE USED IN LIEU O ZEE PURLINS, BLOCKING MUST BE SAME DEPTH AS INSULATION. 3. PURLIN SPACING AND ASTENER TYPE WILL BE DEPENDENT ON GOVERNING CODE AND SPECIICATION REQUIREMENTS. ZEE PURLIN MINIMUM 24 GAUGE, DEPTH DETERMINED BY INSULATION THICKNESS AND LEGS DETERMINED BY PITCH O METAL DECK BUTT INSULATION UP TO PURLIN ZEE PURLIN DETAIL INSULATED DECK DETAIL ST-5

14 DEEP VEE PANEL SPANISH TILE ASTENERS; 20" O.C. MAX. SPANISH TILE EAVE CLOSURE DRIP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. ASTENERS; MIN. 2 PER EAVE CLOSURE PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD # 30 ELT UNDERLAYMENT SOLID SHEATHING 1. I SOLID SHEATHING (BY OTHERS) IS USED, SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELTING UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1 7/8" 2 1/8" DRIP LASHING EAVE CLOSURE EAVE DETAIL ST-10

15 DEEP VEE PANEL SPANISH TILE ASTENERS AT EACH PURLIN ASTENERS; 20" O.C. MAX. CAULK ASTENER HEADS ASTENERS; MIN. 2 PER EAVE CLOSURE PURLIN (SEE NOTE 1) SPANISH TILE EAVE CLOSURE ASTENERS; 20" O.C. MAX. DRIP LASHING; 4" END LAPS WITH (2) BEADS CONTINUOUS CAULK AT LAPS ANGLE LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASCIA PANEL 1. PURLIN SPACING TO BE DETERMINED BY OTHERS, MAXIMUM SPACING 5'-0". 2. ALL CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 12" MIN. 1 7/8" 2 1/8" DRIP LASHING EAVE CLOSURE ALTERNATE EAVE DETAIL OPEN RAMING CONDITION ST-11

16 SPANISH TILE (RIDGE CAP) RIDGE LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS POP RIVET TO ZEE CLOSURE 40" O.C. MAX. SPANISH TILE ASTENERS; 20" O.C. MAX. DEEP VEE PANEL ZEE CLOSURE CUT TO IT BETWEEN DEEP VEE PANEL RIBS CONTINUOUS BEAD O CAULK BETWEEN ZEE CLOSURE AND DEEP VEE PANEL # 30 ELT UNDERLAYMENT SOLID SHEATHING ASTENERS; MINIMUM 2 PER ZEE CLOSURE 1. IELD CUT ZEE CLOSURE TO IT BETWEEN PANEL RIBS. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE MIN. 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1" 1" 1" 3" 1/2" 5/16" 3" 1/2" 1 5/8" OPEN HEM RIDGE LASHING ZEE CLOSURE RIDGE/HIP DETAIL ST-20

17 SPANISH TILE (RIDGE CAP) RIDGE LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS POP RIVET TO ZEE CLOSURE 40" O.C. MAX. SPANISH TILE ASTENERS; 20" O.C. MAX. DEEP VEE PANEL ZEE CLOSURE CUT TO IT BETWEEN DEEP VEE PANEL RIBS CONTINUOUS BEAD O CAULK BETWEEN ZEE CLOSURE AND DEEP VEE PANEL PURLIN CONTINUOUS LASHING ANGLE ASTENERS; MINIMUM 2 PER ZEE CLOSURE 1. IELD CUT ZEE CLOSURE TO IT BETWEEN PANEL RIBS. 2. ALL CAULKING, ASTENERS AND PURLIN ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1" 1" LASHING ANGLE 3" 1/2" 1" 5/16" 3" 1/2" 1 5/8" OPEN HEM RIDGE LASHING ZEE CLOSURE RIDGE/HIP DETAIL OPEN RAMING CONDITION ST-21

18 SPANISH TILE (RIDGE CAP) SNAP LOCK ONTO RIDGE END CLOSURE CONTINUOUS BEAD O CAULK RIDGE END CLOSURE IELD ABRICATE CONTINUOUS BEAD O CAULK BETWEEN RIDGE END CLOSURE AND ZEE CLOSURE IELD CUT LAST PANEL AND ORM AROUND DRIP LASHING. PANEL TO BE CONTINUOUS ROM RIDGE TO EAVE DRIP LASHING AT GABLE SEE DETAIL ST-30 ASTENERS; 2 EACH SIDE O RIDGE # 30 ELT UNDERLAYMENT ZEE CLOSURE, RIDGE LASHING AND CAULKING NOT SHOWN OR CLARITY, SEE DETAIL ST-20 SOLID SHEATHING 1. IELD ABRICATE RIDGE END CLOSURE SEE BELOW. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE A MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. USE EAVE CLOSURE OR TEMPLATE O CURVE 1 1/2" IELD ABRICATED RIDGE END CLOSURE GABLE AT RIDGE ST-22

19 SPANISH TILE ASTEN TO RIDGE CAP DEEP VEE PANEL RIDGE CAP; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS, POP RIVET TO ZEE CLOSURE 40" O.C. ASTENER AT PANEL RIB 20" O.C. MAX. SPANISH TILE ZEE CLOSURE; IELD CUT TO IT BETWEEN PANEL RIBS # 30 ELT UNDERLAYMENT CONTINUOUS BEAD O CAULK BETWEEN ZEE CLOSURE AND DEEP VEE PANEL ASTENERS; MIN. 2 PER ZEE CLOSURE LAP ELT OVER RIDGE ASTENERS; 40" O.C. MAX. SOLID SHEATHING 1. IELD CUT ZEE CLOSURE TO IT BETWEEN RIBS O DEEP VEE PANEL. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. 1/2" OPEN HEM 1" 1" 1 5/8" RIDGE CAP ZEE CLOSURE SHED ROO RIDGE CAP DETAIL ST-23

20 SPANISH TILE ASTENERS; 20" O.C. MAX. TOP LAYER O ELT TO BE PARALLEL WITH GABLE DEEP VEE PANEL; IELD CUT LAST PANEL AND ORM AROUND DRIP LASHING. PANEL TO BE CONTINUOUS RIDGE TO EAVE 1/2" DRIP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. SOLID SHEATHING CONTINUOUS BEAD O CAULK 1. LAST DEEP VEE PANEL IN RUN TO BE IELD CUT AND ORMED AROUND DRIP LASHING. PANEL MUST BE CONTINUOUS RIDGE TO EAVE. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" 1/2" DRIP LASHING GABLE DETAIL ST-30

21 POP RIVET TILE TO CHANNEL SPANISH TILE; IELD CUT AND ASTEN TO PANEL RIB TOP LAYER O ELT TO BE PARALLEL WITH GABLE CHANNEL CLOSURE; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS CONTINUOUS BEAD O CAULK START IRST PANEL HERE 1/2" DRIP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. # 30 ELT UNDERLAYMENT SOLID SHEATHING 1. IELD CUT SPANISH TILE AS REQUIRED. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 4" 1" 2 3/8" DRIP LASHING CHANNEL CLOSURE GABLE DETAIL ST-31

22 SPANISH TILE ASTENERS; 20" O.C. MAX. DEEP VEE PANEL; IELD CUT LAST PANEL AND ORM AROUND DRIP LASHING. PANEL TO BE CONTINUOUS RIDGE TO EAVE 1/2" DRIP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASCIA / SIDING ASTENERS AT EACH PURLIN ASTENERS; 20" O.C. MAX. PURLIN SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1. LAST DEEP VEE PANEL IN RUN TO BE IELD CUT AND ORMED AROUND DRIP LASHING. PANEL MUST BE CONTINUOUS RIDGE TO EAVE. = INISH SIDE 1/2" 1/2" DRIP LASHING SUB-LASHING GABLE DETAIL ST-32

23 ASTENERS AT LAPS AND STAGGERED 20" O.C. CAULK ASTENER HEADS SLOPE CAP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS, POP RIVET TO COUNTER LASHING 40" O.C. MAX. ASTENERS; 20" O.C. MAX. COUNTER LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS, POP RIVET TO ZEE CLOSURE 40" O.C. MAX. ZEE CLOSURE CUT TO IT BETWEEN PANEL RIBS SPANISH TILE DEEP VEE PANEL ASTENERS; 20" O.C. MAX. SOLID SHEATHING # 30 ELT UNDERLAYMENT SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS; 40" O.C. MAX. SPANISH TILE ASTEN TO COUNTER LASHING CONTINUOUS BEAD O CAULK BETWEEN ZEE CLOSURE AND DEEP VEE PANEL ASTENERS; MIN. 2 PER ZEE CLOSURE 1. IELD CUT ZEE CLOSURE TO IT BETWEEN RIBS O DEEP VEE PANEL. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SLOPE SLOPE 1" 1" 1/2" OPEN HEM 1 5/8" COUNTER LASHING CAP LASHING SUB-LASHING ZEE CLOSURE PARAPET DETAIL ST-40

24 SPANISH TILE ASTEN TO COUNTER LASHING COUNTER LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS, POP RIVET TO ZEE CLOSURE 40" O.C. DEEP VEE PANEL ZEE CLOSURE; CUT TO IT BETWEEN PANEL RIBS ASTENERS AT PANEL RIB 20" O.C. MAX. SPANISH TILE # 30 ELT UNDERLAYMENT # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. ASCIA PANEL CONTINUOUS BEAD O CAULK BETWEEN ZEE CLOSURE AND DEEP VEE PANEL ASTENERS; MIN. 2 PER ZEE CLOSURE SOLID SHEATHING SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1. IELD CUT ZEE CLOSURE TO IT BETWEEN RIBS O DEEP VEE PANEL. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SLOPE 1" 1" 1 5/8" 1/2" OPEN HEM COUNTER LASHING SUB-LASHING ZEE CLOSURE HEAD WALL DETAIL ST-50

25 ASCIA PANEL ASTENERS; 20" O.C. MAX. # 30 ELT UNDERLAYMENT COUNTER LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS DEEP VEE PANEL, IELD CUT AND ORM LASHING LEG PANEL CONTINUOUS RIDGE TO EAVE ASTENER AT PANEL RIB 20" O.C. MAX. SPANISH TILE SOLID SHEATHING # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1. IELD CUT AND ORM LASHING LEG ON LAST PANEL IN RUN. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE COUNTER LASHING SUB-LASHING RAKE WALL DETAIL ST-51

26 REGLET LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS SPANISH TILE ASTEN TO COUNTER LASHING COUNTER LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS, POP RIVET TO ZEE CLOSURE 40" O.C. DEEP VEE PANEL ZEE CLOSURE; CUT TO IT BETWEEN PANEL RIBS ASTENERS AT PANEL RIB 20" O.C. MAX. SPANISH TILE # 30 ELT UNDERLAYMENT SOLID SHEATHING CONTINUOUS CAULK AT REGLET REGLET # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. CONTINUOUS BEAD O CAULK CONTINUOUS BEAD O CAULK BETWEEN ZEE CLOSURE AND DEEP VEE PANEL ASTENERS; MIN. 2 PER ZEE CLOSURE ASTENERS; 20" O.C. MAX. SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1. IELD CUT ZEE CLOSURE TO IT BETWEEN RIBS O DEEP VEE PANEL. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SLOPE 1" 1" 1 5/8" 1/2" OPEN HEM COUNTER LASHING REGLET LASHING SUB-LASHING ZEE CLOSURE HEAD WALL DETAIL ST-52

27 CONTINUOUS BEAD O CAULK AT REGLET ASTENERS; 20" O.C. MAX. # 30 ELT UNDERLAYMENT CONTINUOUS BEAD O CAULK REGLET LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS DEEP VEE PANEL, IELD CUT AND ORM LASHING LEG PANEL CONTINUOUS RIDGE TO EAVE ASTENER AT PANEL RIB 20" O.C. MAX. SPANISH TILE SOLID SHEATHING # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS TOP LAYER O ELT TO BE PARALLEL WITH RAKE WALL 1. IELD CUT AND ORM LASHING LEG ON LAST PANEL IN RUN. 2. I SOLID SHEATHING (BY OTHERS) IS USED SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE REGLET LASHING SUB-LASHING RAKE WALL DETAIL ST-53

28 SPANISH TILE DEEP VEE PANEL ASTENERS; 20" O.C. MAX. SPANISH TILE EAVE CLOSURE TRANSITION LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS, POP-RIVET TO ZEE CLOSURE 40" O.C. MAX. ASTENERS; 20" O.C. MAX. SOLID SHEATHING SLOPE SUB LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. CONTINUOUS BEAD O CAULK BETWEEN ZEE CLOSURE, DEEP VEE PANEL ASTENERS; MIN. 2 PER ZEE ZEE CLOSURE (CUT TO IT BETWEEN DEEP VEE PANEL) 1. IELD CUT ZEE CLOSURE TO IT BETWEEN PANEL RIBS. 2. I SOLID SHEATHING (BY OTHERS) IS USED, SHEATHING MUST BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SLOPE 1" 1" OPEN HEM 1 5/8" TRANSITION LASHING ZEE CLOSURE SLOPE TRANSITION DETAIL ST-60

29 SPANISH TILE ASTENERS; 20" O.C. MAX. DEEP VEE PANEL EAVE CLOSURE SEE DETAIL ST-71 CONTINUOUS BEAD O CAULK BETWEEN VALLEY LASHING & ELT UNDERLAYMENT SOLID SHEATHING # 30 ELT UNDERLAYMENT ANCHOR CLIPS; 20" O.C. MAX. 1. SOLID SHEATHING IS REQUIRED AT THIS CONDITION, WHEN SPANISH TILE IS USED OVER OPEN RAMING SEE DETAIL ST SOLID SHEATHING (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS (METAL CORRUGATED SHEATHING MAY BE USED IN LIEU O PLYWOOD). 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. VALLEY LASHING 12" (2) CONTINUOUS BEADS O CAULK AT LAPS 1/2" 20 1/2" MIN. 20 1/2" MIN. 1/2" ASTENERS THROUGH VALLEY ONLY AT TOP O LASHING UNDER LAP, NO ASTENERS ARE TO BE EXPOSED ON TOP (OVERLAPPING) VALLEY VALLEY LASHING DETAIL ST-70

30 SPANISH TILE DEEP VEE PANEL SOLID SHEATHING SPANISH TILE EAVE CLOSURE 4" MIN. # 30 ELT UNDERLAYMENT # 30 ELT UNDERLAYMENT PARALLEL TO VALLEY CONTINUOUS BEAD O CAULK VALLEY LASHING OR VALLEY EAVE CLOSURE ONLY POP RIVET EAVE CLOSURE TO RIB O PANEL THROUGH TAB ONLY DEEP VEE PANEL RIB IELD CUT TAB IN EAVE CLOSURE VALLEY LASHING MIN. 20 1/2" EACH SIDE O VALLEY CENTER LINE 4" MIN. CENTER LINE O VALLEY STAGGERED PATTERN O TILE AND DEEP VEE PANEL AT VALLEY DEEP VEE PANEL RIB SPANISH TILE ROO PLAN VIEW VALLEY ISOMETRIC ST-71

31 SPANISH TILE ASTENERS; 20" O.C. MAX. DEEP VEE PANEL EAVE CLOSURE SEE DETAIL ST-71 SEE DETAIL ST-71 OR TILE PATTERN GRACE ICE AND WATER SHIELD SOLID SHEATHING ANCHOR CLIPS; 20" O.C. MAX. GRACE ICE AND WATER SHIELD RUN RIDGE TO EAVE LAT SHEET VALLEY SUB-LASHING RUN RIDGE TO EAVE SEE SECTION SLOPE LAT SHEET VALLEY SUB-LASHING GRACE ICE AND WATER SHIELD CORRUGATED S-DECK USE 2" ZEE-RIB AS PER DETAIL Z-90, Z-91 RIDGE EAVE EACH SIDE 16 GA. HAT SECTION PURLIN CORRUGATED S-DECK SECTION SLOPE 16 GA. HAT SECTION SIZED TO IT OVER PURLIN AND TO ACCOMMODATE THE DEPTH O THE CORRUGATED S-DECK. PURLINS ROOS WITH A SLOPE O 4:12 OR LESS 6'-0" MIN. ROOS ABOVE 4:12 3'-0" MIN. VALLEY DETAIL OPEN RAMING; 2" ZEE-RIB ST-72

32 ROO PIPE PENETRATION O 4" DIA. OR LESS RUBBERIZED "BOOT" LASHING CONTINUOUS CAULK OR STAINLESS STEEL HOSE CLAMP PIPE PENETRATION TO BE IN PAN O PANEL ONLY SPANISH TILE SET RUBBERIZED BOOT INTO CONTINUOUS BEAD O CAULK. USE ASTENERS AS SPECIIED BY BOOT MANUACTURER. CAULK ASTENER HEADS. IELD CUT TILE TO IT AROUND BOOT DEEP VEE PANEL # 30 ELT UNDERLAYMENT SOLID SHEATHING CUT PANEL 1" SMALLER THAN PENETRATION, BACK CUT TABS, OLD TABS UP AROUND PENETRATION, AND CAULK. 1. CUT HOLE TO ALLOW OR THERMAL MOVEMENT I PANELS ARE 30'-0" OR LONGER. 2. I PIPE IS MADE O METAL, IT MUST BE PAINTED TO PREVENT RUST RUN-O ROM STAINING PANELS. 3. POSITION SQUARE BASED BOOTS IN A DIAMOND ORIENTATION WHERE POSSIBLE TO AID IN DIVERTING WATER. PIPE PENETRATION (PREERRED METHOD) IN PAN O PANEL ONLY OPEN RAMING AND SOLID SUBSTRATE ST-80

33 SPANISH TILE SYSTEM DEEP VEE PANEL; IELD CUT RIBS AND LAP, LAP IN DIRECTION O WATER LOW ** SECTION A ST-82 ** SECTION B ST-82 I PIPE IS MADE O METAL IT MUST BE PAINTED TO PREVENT RUST RUNO ROM STAINING PANELS CAULK AT SNIPPED OPENING RIB CLOSURE; SEE BELOW IELD CUT TILE AS REQUIRED CONTINUOUS BEAD O CAULK RUN RIB UP TO STACK ** CALL BMC BEORE USING THIS DETAIL DEEP VEE PANEL RIBS ASTENER RIB CLOSURE; IELD CUT AND ORM TO IT INSIDE PANEL RIBS THUMB TAB 1/2" PIPE PENETRATION O PANEL SEAM ISOMETRIC VIEW **CALL BMC BEORE USING THIS DETAIL ST-81

34 SECTION A USE THIS DETAIL WHEN STACK IS AT PANEL RIB CUT AND LATTEN OUT RIB, CUT LATTENED RIB APPROX. 2" WIDTH, LAP TOP RIB IN DIRECTION O WATER LOW ROUND STACK RIB CLOSURE SEE DETAIL ST-81 IELD CUT TILE AS REQUIRED RUN RIB UP TO STACK AND CAULK CUT DEEP VEE PANEL AND BEND UP 1" AROUND STACK AND CAULK # 30 ELT UNDERLAYMENT 1. SOLID SHEATHING IS REQUIRED AT THIS CONDITION, WHEN SPANISH TILE SYSTEM IS USED OVER OPEN RAMING (SEE DETAIL ST-87) SOLID SHEATHING 2. IELD CUT RIB 2" BACK ROM STACK AT UPPER PANEL, MITER RIB AT LOWER PANEL AND HOLE IN PANEL 1" LESS THAN DIA. O STACK, BACK CUT HOLE AND BEND PANEL UP AROUND STACK **CALL BMC BEORE USING THIS DETAIL SECTION B USE THIS DETAIL WHEN STACK IS AT PANEL PAN ROUND STACK IELD CUT TILE AS REQUIRED CUT DEEP VEE PANEL AND BEND UP 1" AROUND STACK AND CAULK # 30 ELT UNDERLAYMENT 1. SOLID SHEATHING IS REQUIRED AT THIS CONDITION, WHEN SPANISH TILE SYSTEM IS USED OVER OPEN RAMING (SEE DETAIL ST-87) SOLID SHEATHING 2. IELD CUT HOLE IN PANEL 1" LESS THAN DIA. O STACK, BACK CUT HOLE AND BEND PANEL UP AROUND STACK PIPE PENETRATION ROUND STACK DETAILS **CALL BMC BEORE USING THIS DETAIL ST-82

35 SPANISH TILE DEEP VEE PANEL CLEAT; TURN LASHING PAN UNDER AND HOOK ON TO CLEAT ANGLE LASHING SECTION B LASHING IELD ORM ZEE CLOSURE CLEAT; TURN LASHING PAN UNDER AND HOOK ON TO CLEAT COUNTER LASHING SEE BELOW SECTION A SPANISH TILE LOWER PANEL, IELD BEND UP AT CURB LASHING IELD ORM ANGLE LASHING CLEAT; TURN LASHING PAN UNDER AND HOOK ON TO CLEAT ZEE CLOSURE; CUT 2" O HORIZONTAL LEG, BEND VERTICAL LEG AND SLIP BETWEEN DEEP VEE PANELS, CAULK BETWEEN ZEE CLOSURE, COUNTER LASHING AND DEEP VEE PANEL COUNTER LASHING EXTEND 1/4" BEYOND ZEE (LASHING CUT AWAY OR CLARITY) 1/4" SPANISH TILE ROO PENETRATION PLAN VIEW ST-83

36 CURB MATERIAL ANGLE LASHING COUNTER LASHING; POP-RIVET TO ZEE CLOSURE ZEE CLOSURE; (CUT TO IT BETWEEN PANEL RIBS) ANGLE LASHING LASHING; IELD ORM EAVE CLOSURE SPANISH TILE 12" MIN. SPANISH TILE; (CUT TILE SHORTER I REQUIRED PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD DEEP VEE PANEL CONTINUOUS BEAD O CAULK BETWEEN ZEE CLOSURE, AND DEEP VEE PANEL ASTENERS; MIN. 2 PER ZEE CONTINUOUS BEAD O CAULK SOLID SHEATHING # 30 ELT UNDERLAYMENT 1. SOLID SHEATHING IS REQUIRED AT THIS CONDITION, WHEN SPANISH TILE IS USED OVER OPEN RAMING (SEE DETAIL ST-87) 2. SOLID SHEATHING (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS (METAL CORRUGATED SHEATHING MAY BE USED IN LIEU O PLYWOOD). 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1" 1" 2 1/8" 1 7/8" 1 7/8" OPEN HEM COUNTER LASHING ANGLE LASHING ZEE CLOSURE EAVE CLOSURE ROO PENETRATION SECTION - A ST-84

37 WRAP PERIMETER WITH ELT AND ANGLE LASHING SPANISH TILE DEEP VEE PANEL; BEND TO CURB SOLID SHEATHING CURB MATERIAL # 30 ELT UNDERLAYMENT 1. SOLID SHEATHING IS REQUIRED AT THIS CONDITION, WHEN SPANISH TILE IS USED OVER OPEN RAMING (SEE DETAIL ST-87) 2. SOLID SHEATHING (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS (METAL CORRUGATED SHEATHING MAY BE USED IN LIEU O PLYWOOD). 3. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 2" 4" CURB SIZE +8" 4" CURB HEIGHT ANGLE LASHING ROO PENETRATION SECTION - B ST-85

38 EAVE CLOSURE DEEP VEE PANEL SPANISH TILE ANGLE LASHING NOTCH THE SPANISH TILE OR CLEAT LASHING; IELD ORM SLOPE CONTINUOUS CLEAT (CUT AWAY OR CLARITY) ZEE CLOSURE; IELD CUT AND BEND AT END AND CAULK DEEP VEE PANEL; IELD CUT AND ORM SEE DETAIL BELOW LASHING; IELD ORM ANGLE LASHING COUNTER LASHING ZEE CLOSURE DEEP VEE PANEL CAULK BETWEEN ZEE CLOSURE AND COUNTER LASHING AND BETWEEN ZEE CLOSURE AND PANEL ROO PENETRATION ISOMETRIC ST-86

39 1'-0" MINIMUM 1'-0" MINIMUM OR ROO PENETRATIONS LARGER THAN 4" IN DIA. CARRY UP TO NEXT PURLIN GRACE ICE AND WATER SHIELD RUN CONTINUOUS TO EAVE SQUARE OR ROUND PENETRATION LAT SHEET SUB-LASHING RUN CONTINUOUS TO EAVE SLOPE CORRUGATED S-DECK SEE SECTION PURLINS EAVE LAT SHEET VALLEY LASHING GRACE ICE AND WATER SHIELD 16 GA. HAT SECTION SIZE TO IT OVER PURLIN AND TO ACCOMMODATE THE DEPTH O THE CORRUGATED S-DECK. 16 GA. HAT SECTION PURLIN CORRUGATED S-DECK SECTION ROO PENETRATION LARGER THAN 4" OPEN RAMING ST-87