SCOPE OF ACCREDITATION TO ISO/IEC 17020:2012. CONCRETE SOLUTIONS LAB, INC. 68 Commerce Drive Farmingdale, NY Thomas Kalb

Size: px
Start display at page:

Download "SCOPE OF ACCREDITATION TO ISO/IEC 17020:2012. CONCRETE SOLUTIONS LAB, INC. 68 Commerce Drive Farmingdale, NY Thomas Kalb"

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17020:2012 CONCRETE SOLUTIONS LAB, INC. 68 Commerce Drive Farmingdale, NY Thomas Kalb INSPECTION BODY Valid To: May 31, 2019 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this Type A (Third Party) inspection body for the following Special Inspections and has been assessed against the applicable New York City Special Inspection requirements for the specific inspections identified below: Description of Inspection Special Inspections Wall Panels, Curtain Walls and Veneers Procedure and/or Rules of the City of The inspection of quality, New York, 1RCNY workmanship and requirements for , Appendix A; construction. Materials, inspection New York City and testing shall conform to Building Codes; The applicable standards listed in the International family of Codes based on the Building Codes (IBC) International Building Codes 2014 (IBC) and each state s modifications to these codes and to the rules of the Local Code Officials. Specifically, New York City Chapter 1 of Title 28 of the Administrative Code for additional provisions relating to materials, testing and inspections. BC and In-House Procedure 27 Exterior Insulation Finish (EIFS) BC Compliance with filed plans and In-House Procedure 28 Chimneys BC ; BC Procedure 12 (A2LA Cert No ) Revised 01/30/2018 Page 1 of 5

2 Description of Inspection Procedure and/or Flood Zone Compliance BC G105; BC Luminous Egress Path Markings BC ; BC Class 2 Buildings Sprayed Fire- Materials and Mastic and Intumescent Fire- Coating Smoke Control BC ; BC 909 Sprinkler and Standpipe System Fire-resistant Penetrations and Joints Emergency and Standby Power (Generators) BC ; BC BC ; BC ; BC 903 BC BC ; BC ; BC 2702 BC ; BC ; NYCMC 1011; NYCMC 1018; NYCMC 1208 Fuel-Oil Storage & Fuel-Oil Piping Private On-Site Storm Water Disposal and Detention Facilities, and Individual On-Site Private Sewage Disposal Installation including Soil Percolation Tests for septic and drywell Procedure 4 Procedure 14 Procedure 5 Plumbing & BC ; BC ; Manufacturer Instructions BC ; BC ; BC Procedure 23 & Fire- Plumbing & Plumbing & Plumbing and (A2LA Cert No ) Revised 01/30/2018 Page 2 of 5

3 Description of Inspection Procedure and/or Heating BC ; BC Procedure 16 Plumbing and Cold-Formed Steel BC ; BC Steel High- Strength Bolting BC Steel -- Welding BC Steel -- Detail BC Concrete-Cast-in-Place & Precast (Note: Licensed concrete testing lab to perform sampling and testing of cylinders) BC Procedure 2 Masonry BC Procedure 6 Wood Prefabricated Wood I-Joists, Metal plate Connected Wood Trusses, and High-load Diaphragms Subsurface Conditions- Subgrade Inspection Subsurface Conditions Fill Placement, In place Density BC BC BC ; BC ; BC Procedure 19 Procedure 1 (A2LA Cert No ) Revised 01/30/2018 Page 3 of 5

4 Description of Inspection Subsurface Investigations, (Borings & Test Pits) Procedure and/or BC ; BC 1802; BC Deep Foundations BC ; BC 1808; BC 1809; BC 1810 Procedure 17 Procedure 19 Vertical Masonry Foundation BC Underpinning BC ; BC 1814 Stability Existing Buildings, Demolition, and Raising and Moving of a Building Excavation-Sheeting, Shoring and Bracing BC ; BC BC ; NYCBC , and In-House Procedure 20 Procedure 21 Procedure 22 Seismic Isolation BC Procedure 26 Post-Installed Anchors BC Helical Piles BC Standard for Agencies Engaged in Inspection, Testing or Special Inspection ASTM E This specification defines the minimum requirements for agencies engaged in: a) Inspection of construction activities and materials used in construction, b) Testing of construction activities and materials used in construction, and c) Special Inspection (A2LA Cert No ) Revised 01/30/2018 Page 4 of 5

5 Description of Inspection Procedure and/or Standard for Agencies Engaged in Inspection and/or Testing ASTM E This specification defines the minimum requirements for inspection agency personnel or testing agency laboratory personnel, or both, and the minimum technical requirements for equipment and procedures utilized in the testing and inspection of construction and materials used in construction. (A2LA Cert No ) Revised 01/30/2018 Page 5 of 5

6 Accredited Inspection Body A2LA has accredited CONCRETE SOLUTIONS LAB, INC. Farmingdale, NY for technical competence in and compliance with the Inspection Body Accreditation Program This inspection body is accredited in accordance with the recognized International Standard ISO/IEC 17020:2012 Conformity Assessment Requirements for the operation of various types of bodies performing inspection. This accreditation demonstrates technical competence for a defined scope and the operation of a quality management system. Presented this 28 th day of July President and CEO For the Accreditation Council Certificate Number Valid to May 31, 2019 For the inspections to which this accreditation applies, please refer to the organization s Inspection Body Scope of Accreditation.