w w w. s a q u l i t y m e ta l s. c o m

Transcription

1 san antonio branch 210 W. Peden San Antonio TX P. (210) F. (210) MCALLEN branch 2221 Austin Ave McAllen TX P. (956) F. (956) w w w. s a q u l i t y m e ta l s. c o m dallas branch 2515 Willowbrook Rd Ste 100 Dallas TX P. (972) F. (972)

2 important notice

3 Introduction ML-100 is a non-structural panel which is mechanically seamed during installation. The product is an integral interlocking system by design meaning the panels install in one direction from a given starting point. with a wide range of building designs. Two clips are center point allowing for multi-directional expansion. Factory Apply Sealant available. Applications fascia, equipment screens, mansards, and wall panels. This system may also be installed on tapered and curved roof areas. other applications. Design ML-100 Standing Seam requires low maintenance. The panel is secured with concealed clips and the panel side laps are locked together using a rooftop seaming machine. Testing UL 790 Fire Test of Roof Coverings, Class A, B, C UL 2218 For Impact Resistance, Class 4 UL 580 Uplift Resistance. Class 90 Construction No INSTALLATION Solid Substrate Required Snap Seam No Field Seaming Required Weather Tight Warranty is not Available Underlayment Required Oil Canning reduce the incidence of oil canning in the panels. Installer must have prior experience and knowledge of the tolls listed below and their uses in working with Specifications Color and Finishes 24 and 26 Gauge Galvalume 35 Year Finish Warranty on Kynar 500 Finish Widths Actual Panel Coverage (Width): Minimum Slope = 3":12" Lengths ML-100 Panel is available in standard lengths from 4 to 40. Longer lengths require additional handling, packaging, and shipping considerations. An extra handling charge may apply to panels over 40. Continuous Rollformed Lengths: eliminates need for panel lap joints. Caulking Gun Snips Cordless Screw Gun Pop Rivet Tool Tape Measure Hemming Tool Electrical Extension Cord Heavy Gloves Safety Glasses

4 Packaging Options Standard packing A packaging charge will be added to all orders. Standard packing is crating for all orders. Storage Bare Galvalume and painted panels can be expected to give many years of rust-free service when precautions are taken during storage. If metal is not to be used immediately, store inside in a well ventilated, dry location. Any outdoor storage is at the customer s own risk! At time of delivery, inspect panels for moisture. If moisture has formed, the panels should be uncrated, wiped dry, and allowed to dry completely. Failure to remove the entrapped moisture between the sheets immedi- Extended storage of panels in a bundle is not recommended. Storage on Roof, Crates need to be placed parallel to the framing members and the slope of the roof. LTL packing For LTL, panels are packaged in a completely enclose crate to provide optimum protection. Additional charges will apply for non-standard packing and special requests. Strippable film Removal applied to the topside of the panel to prevent possible damage to the painted surface. If panel has a protective sunlight and high temperatures. remain on the panels after installation. Lead Time Please allow 2-3 days for delivery for material or colors we have in stock. Color we have to paint please allow working days. Receiving Materials It is the responsibility of the installer to unload material from the delivery truck. The installer shall be responsible for providing suitable equipment for unloading of material from the delivery truck. After receiving material, check the condition of the material, and review the shipment against the shipping list to ensure all materials are accounted for. If damages or shortages are discovered, it should be noted on the shipping copy at time of delivery. If material is delivered by common carrier, a claim must be made with the carrier as soon as possible

5 mechanical handling: Forklift A forklift may be used for panels up to 20 long. Please make sure the forks are at their maximum separation. Do nor transport open crates. When transporting crates across rough terrain, or for a long distance, some means of supporting the panel load must be used. Improper loading and unloading of crates may result in bodily harm and /or material damage. Union Corrugating is not responsible for bodily injuries and/or material damages resulting from impoper loading and unloading. general handling Each crate should be handled carefully to avoid being damaged. Care should be taken to prevent bending of for proper care while unloading and handling crates in order to prevent panel damage: 1. Crates should remain intact during any handling, and until the individual panels in each bundle are ready to be installed. Crates should never be lifted by the banding. 2. Lift each crate as close as possible to its center of gravity. crane A crane should be used when lifting panels with lengths greater than 20. please be sure to utilize a spreader bar to ensure the even distribution of the weight to the pick up points. As a rule, when lifting panels, no more than 1/3 of the length of the panel should be left unsupported. Canvas or nylon slings should be used to pick up the panels. DO NOT use cable or chains because this will damage the panels. 3. If the crates are to be lifted with a crane, use a spreader bar of appropriate length, and nylon band slings. (Do not use wire rope slings as they will damage the panels). 4. Depending on panel length, some crates may be lifted by a forklift. When using a forklift, the forks should be spread apart to their maximum spacing, and the load must be centered on the forks to prevent scratching the next panel. A panel should never be picked up by it s ends. Instead, lift the panel along its longitudinal panels over 10 feet long, two or more people should lift the panel along the same edge. 5. After creates are opened, individual panels must also be handled carefully to prevent panel buckling or damage to the panel coating. When removing a panel from a crate, it should never be allowed to slide over another panel. The individual panels should be rolled out of the crate in order to minimize the chance of panel damage

6 manual handling: 6. Soft gloves must be worn when handling panels. A panel should never be picked up by its ends. Instead, lift the panel along its longitudinal edge and carry in a All applicable safety regulations, including OSHA regulations, must be complied with during the panel installation process. FOOT TRAFFIC: 6-8 MAX necessary for maintenance over certain areas of the roof, then a permanent walkaway should be installed. field cutting The snips or a nibbler type electric tool are recomused, the blade will generate silvers of metal chips. Any silvers of metal chips must be immediately removed from the Nail Strip panels because they will damage the panels over when cutting. This allows the silvers of metal chips to be brushed from the back side and avoids damaging the paint on the top side of the panels. - tion, provide walking platforms to avoid any panel damage as shown below. Walking on the ribs can cause damage of the panels. Walking Platforms All product surfaces should be free of debris at all times. Installed surfaces should be wiped clean at the end of each work period. Never cut panels over metal surfaces. Metal shavings will rust on the surface thus voiding the warranty. Quality Metals Panels Foot Traffic When cutting metal panels, goggles must be worn for eye protection Quality Metals Panels - 4 -

7 design considerations & calculations Proper design and installation of vapor barriers and ventilation systems are important to prevent condesation and the resulting problems of moisture damage an Vent Attic Insulation Concensation occurs when moisture-laden air comes in contact with a surface temperature equal to or below the dew point of the air. This phenomenon creates problems that are not unique with metal buildings; these problems are common to all types of construction. In addition to providing resistance to heat transfer, insulation can also protect against condensation forming on cold surfaces, either inside the building or within the wall/roof system cavity. The arrangement of the building s insulation system and vapor retarder is the responsibility of the building designer. These are some basic guidelines to help contro condensation in a metal building: 1. The insulation should have a vapor retarder face on the warm side of the insulation. For most buildings, this means that the vapor retarder is on the side surface. (toward the building s interior) 2. The thickness of the insulation must be designed to maintain the temperature of the vapor retarder above the interior dew point, using the worst-case expected outside temperature. 3. All perimeter conditions, seams, and penetrations of the vapor retarder must be adequately sealed in order to provide a continuous membrane to resist the passage of water vapor. Touch Up Paint: Vent at Eave result in some small scratches or nicks to the paint Touch-up paint is available in matching colors. It is recommended that a small brush be used to apply touch-up paint to those areas that are in need of repair. Touch-up paint does not have the superior chalk and will normally discolor at an accelerated rate. Periodic touch-up may be required to maintain color match. There is no warranty on touch-up paint in regards to color match because the paint processes are Aerosol paint should not be used because of the overspray that may occur. 4. Building ventilation, wheter by gravity ridge vent, power operated fans, or other means, contributes, signifacly to reduce condensation. The movement of air to the outside of the building reduces the interior level of vapor pressure. On buildings that have an attic space or are being retroplaced at both ends of the eave and peak of the roof in order to prevent a buildup of moisture (humidity) in the attic space. Touch-Up Paint Small Brush - 5 -

8 accesories 14 x 7/8 Hex Head Lap Tek Screw metal to metal #9 x 1-½ Hex Head Woodmate Screw Metal-to-Wood #10 x 1 Pancake Head Woodscrew 2 Pancake Head Woodgrip 1-½" 1-½" 36" 1-3/4" 1 Pancake Head Tek Screw 2-½ Pancake Head Tek Screw Neoprene Universal Closure Vented Ridge Closure Closure Tube Sealant Hand Crimper Double Bead Butyl Tape (7/8 x 3/16 x 40 ) Pipe Boot (Various sized, heat treated Clips Roll Valley 20 x 50 Hemming Tool Bearing Plate - 6 -

9 fastener installation recomended toll type Use depth locating nose or adjustable clutch on screw gun to prevent over-drilling and strip out. Do not use impact tools or runners. washer. DO NOT OVERDRIVE THE FASTENER. self driller correct too loose too tight Sealing material slightly visible at edge of metal washer. Sealing material is not visible; not enough compression to seal. woodscrew Metal washer deformed; sealing matereial pressed beyond washer edge. condition of substructure: Whether over solid substrate or open structural framing, panel distortion may occur if not applied over properly aligned and uniform substructure. The installer should check the roof deck for squareness before installing Mechanical Lock ML-100 panels. Several methods can be used to verify squareness for proper installation of the panels. Method 1 Measure diagonally across one slope of the roof from similar points at the ridge and eave and obtain the same dimension. Method 2 Measure a point from the corner along the edge of the roof at a module of three (3). Measure a point from the same corner along another edge at a module of four (4). Then by measuring diagonally between the two points stablished, the dimension corner. Multiple uses of this system may be required to determine building squareness. If the endwall cannot be made square, the roof system cannot be installed as shown in these instructions. To prevent wobbling make sure fastener head is completely engaged in the socket. If the head does not go all the way in the socket tap the magnet deeper into the socket to allow full head engagement. Metal chips will build up from drilling and should be removed from time to time. Protect drill point. Push only hard enough on the screw gun to engage clutch. This prevents excess friction and burn out of the drill point. Correct pressure will allow screw to drill and tap without binding. Drilling through sheet and insulation ease up on pressure when drilling through insulation to avoid striking the purlin or girt with the pont apply more pressure after drill point contacts purlin or girt. Drilling through purlin overlaps. Drilling through lapped purlins requires extra care. Excessive voids between purlins sometimes damages drill ponts and two self drillers might be necessary to complete the operation

10 ML SERIES installation The three drawings below ilustrate the seaming process. Starting with Step 1, clips are installed over the male leg and fastened to the substrate. Step 2. involves the female leg of the adjoining panel to then be set on the male leg/clip assembly. Step 3 involves the panels to be seamed, with either a mechanical or hand seamer. The seam shown is a 90 degree seam or a 180 degree or double seam is optional. This type of seam is typically required where high wind loads are needed. Data from extensive wind step 1 Hand tool positioned over seam step 1 step 2 step 3 HAND CRIMPER step 2 Hand tool locked onto seam step 3 Hand tool crimps seam - 8 -

11 ML SERIES installation electric seamer: The electric seamer will run in one direction only. To determine the direction of the seamer, stand at the eave and look upslope. If the roof is being installed left to right, the seamer will run upslope. If the roof is being installed right, the seamer will run upslope, an orientation plate is on the seamer to assist you in placing the seamer onto the seam properly. Shen the roof has endlaps, the panels will always be installed right to left. When the roof slope is 6 on 12 or greater, panels must run right lo left. To begin seaming, set seamer on seam with the locking bar up and to the open side of the seam. The rear wheels should be even with the edge of the roof panel. Push the locking bar down to engage the rolls and turn the seamer on. Stop seamer about one foot from end panels. Disengage locking bar and remove the electric seamer. Finish seam with hand tool. caution Seamer operation should be closely supervised at all times. A safety line should be attached to the seamer. Do not entangle the electrical cords in the seamer tooling while it is in operation. This could couse serious injury or death to the operator and severely damage the seamer. Electrical cords should be 10-gouge to provide power to the semaer and never be over 200 feet from the electrical source - 9 -

12 trim diagram 2 5 RAKE / EAVE 1 end wall ridge cap gutter valley PITCH CHANGE downspot

13 RC24-SO13 A= 6 B=½ RC24-SO12 A=5 B=1 RC24-SO16 A=7 B=1 RC24-SO20 A=9½ B=1 RC24-SO24 A=11 B=1 RCS24-SO16 A= 4½ B=1 C=2 D=½ PC24-SO16 A= 5 B=1 C=2 D=7½ E=½ Z24-SO314 A=1 B= 1/4 C=1 Z24-SO334 A=1 ¾ B= 1¼ C=1 Z24-SO414 A=1 B=2 ¼ C=1 3 ¼ 3 ¾ 4 ¼ VENTED ZEE AVAILABLE, PLEASE INQUIRE

14 GUS24-SO235 A=4 B=4 C=7 D 3½ E=1 GU24-SO2114 A= 4½ B= 5¼ C 5½ D= 3 E= 1 F=1 21 ¼ 20 DS24-SO1618 A= 4 B= 3 C= 3½ VC24-SO24 A=4 B=1 C=5 D=1 E=1-12 -

15 CS24-SO418 A=2 B=5/8 C=1½ D=3/16 DRIP EDGE (DL) DL24-SO08 A=3 ¾ B=1 ¼ C=2 D=½ EAVE (OFFSET CLEAT) A EC24-SO08 A=4 B=3 C=½ B C SIDEWALL SW24-SO09 A=3 B=5 C= A C B

16 J-TRIM A JC24-SO06 A=3 3/8 B=1 1/8 C=1 D=½ D B C FW24-SO1078 A=6 B=5 5/8 C=1 ¼ D=½ EW24-SO09 A=3 B=5 C=1 HIGH SIDE FASCIA FH24-SO13 A=3 B=5 C=½

17 eave detail ML PANEL SERIES 10-12X1 WOOD SCREWS -12 O.C X1 WOOD SCREWS -12 O.C. SOLID CLEAT DRIP EDGE CLEAT 1. Install cleat onto fascia with #10-12x1 wood screw 12 O.C. 2. install drip edge by sliding open hem onto cleat & fastening with #10-12x1 wood screw, 12 O.C. on to substrate. 3. Engage drip edge into open hem of panel to begin panel installation

18 gutter detail ML SERIES PANEL CLIP 1. Install all gutter flashings before panel installation. 2. Fasten back of gutter top of fascia w/ #10-12 x 1 Pancake head 24 O.C. 3. Install drip edge over back of gutter & fasten # 10-12x1 Pancake head wood 12 O.C. on top of substrate. 4. Engage field hemmed end of panel top hem of drip edge. DRIP EDGE POP RIVET SOLID DECK FASCIA BOARD GUTTER GUTTER STRAP

19 hip/ridge detail 1. Box ends of panels. 2. Field cut Z closures to fit between panel ribs. 3. Set Z closure in tape sealant or 2 cont. beans of sealant and attach to panel. with (3) #10-12 x1 wood screws. 4. Apply sealant on side legs of Z closure, filling any gaps around panel ribs. 5. Attach ridge/hip flashing to Z closures with a pop rivet on one side at 24 O.C. 6. If additional flashing lengths are required, apply sealant and lap the flashing over the installed flashing by a minimum of 3 securing the connection with pop rivets. ML SERIES ROOF PANEL POP RIVET ONE SIDE ONLY #10-12 X 1 SCREWS Z CLOSURE CUT TO FIT BETWEEN PANEL. SET IN 2 CONT. BEADS OF SEALANT AND CAULKED VERTICALLY AT SEAMS. HIP/RIDGE CAP FLASHING Z CLOSURE

20 metal VENTED RIDGE DETAIL 1. Box ends of panels. 2. Set Z closure in tape sealant or 2 cont. beads of sealant and attach to panel with (3) #10-12 x 1 wood screws. 3. Attach bottom of vented Z closure to top of Z closure with stitch 24 O.C. 4. Hook other hem side of ridge cap onto the long end of the other vented Z closure and pop rivet both 24 O.C. 5. Insert long end of vented Z closure into an open hem side of ridge cap. RIDGE CAP FLASHING VENTED Z PANEL POP 24 O.C. BOX END OF PANEL #10-12 X 1 SCREW (3) PER PANEL Z CLOSURE CUT TO FIT BETWEEN PANEL, SET IN 2 CONT. BEADS OF SEALANT AND CAULKED VERTICALLY AT SEAMS ML SERIES ROOF PANEL Z CLOSURE SOLID DECK

21 VENTED RIDGE DETAIL 1. Box ends of panels. 2. Field cut Z closures to fit between panel ribs. Set Z closure in tape sealant or 2 cont. beads of sealant and attach to panel with (3) x 1 wood screws. 3. Apply sealant on side legs of Z closure, filling any gaps around panel ribs. 4. Attach ridge flashing to Z closures through venting material with a stich screw at 24 O.C. 5. If additional flashing over the installed flashing by a minimum of 3 securing the connection with pop rivets. BOX END OF PANEL RIDGE CAP VENTING MATERIAL STITCH SCREW #10-12 X 1 SCREWS PER PANEL Z CLOSURE CUT TO FIT BETWEEN PANEL, SET IN 2 CONT. BEADS OF SEALANT AND CAULKED VERTICALLY AT SEAMS ML-SERIES ROOF PANEL

22 GABLE DETAIL STITCH SCREW AT 12 O.C. ML SERIES ROOF PANEL CONT. BUTYL TAPE SOLID DECK GABLE FLASHING CLEAT 1. Install cleat on to fascia with #10-12x1 pancake wood screws at 12 O.C. 2. Field bend panel at 90 degrees 1-1/2 minimum. 3. Adhere a continuous length of butyl tape onto the top inside of the panel leg. 4. Slide gable flashing onto cleat and align with panel. 5. Connect gable flashing with a stitch screw at 12 O.C. #10-12 X 1 WOOD 12 O.C

23 valley DETAIL 1. Install all valley flashings before panel installation. 2. Fasten valley flashing to substrate with #10-12 x 1 pancake head wood screws 24 O.C. 3. Align and install offset cleat with tape sealant on both sides of valley flashing. 4. Fasten offset cleat through valley flashing and tape sealant to substrate with #10-12x1 pancake head wood screws 24 O.C. 5. Field hem panel. 6. Engage field hemmed end of panel to offset cleat and attach panel as usual. #10-12 x 1 PANCAKE SCREWS AT 24 O.C. ROOF PANEL FIELD CUT & PANEL ML SERIES ROOF PANEL VALLEY OFFSET CLEAT SOLID DECK CONT. 3/8 x 1 BUTYL TAPE

24 endwall DETAIL WALL SYSTEM ENDWALL FLASHING ML SERIES PANEL ROOF #10-12 x 1 SCREWS (3) PER PANEL 1. Box panel ends. 2. Field cut Z closures to fit between panel ribs. 3. Set Z closure in tape sealant of cont. beads or sealant and attach to panel with (3) #10-12x-1 wood screws. 4. Caulk Z closure vertically at panel seam. 5. Attach high side transitions flashing to Z closure with pop rivets. Z CLOSURE POP RIVET AT 24 O.C. Z CLOSURE CUT TO FIT BETWEEN PANEL, SET IN 2 CONT. BEADS OF SEALANT AND CAULKED VERTICALLY AT SEAMS SOLID DECK

25 endwall DETAIL CAULKING BUTYL TAPE COUNTER FLASHING ENDWALL FLASHING FIELD BOX END OF PANEL ML SERIES ROOF PANEL #10-12 X1 SCREW (3) PER PANEL Z CLOSURE POP RIVET AT 24 O.C. 1. Box panel ends. 2. Field cut Z closures to fit between panel ribs. 3. Set Z closure in tape sealant or cont. beads of sealant and attach to panel with (3) #10-12x-1 wood screws. 4. Caulk Z closure vertically at panel seam. 5. Attach endwall flashing to Z closure with pop rivets 24 O.C. 6. Install counter flashing and caulk top with sealant. Z CLOSURE CUT TO FIT BETWEEN PANEL, SET IN 2 CONT. BEADS OF SEALANT AND CAULKED VERTICALLY AT SEAMS SOLID DECK

26 endwall DETAIL CAULKING FLASH B FIELD BOX END PANEL BUTYL TAPE ML SERIES ROOF PANEL #10-12 x 1 SCREW PANEL 1. Box panel ends. 2. Field cut Z closures to fit between panel ribs. 3. Set Z closure in tape sealant or cont. beads of sealant and attach to panel with (3) #10-12x-1 wood screws. 4. Caulk Z closure vertically at panel seam. 5. Attach endwall flashing to Z closure with pop rivets 24 O.C. and set top of flashing in wall. 6. Caulk with sealant.- FLASH A POP RIVET AT 24 O.C. Z CLOSURE CUT TO FIT BETWEEN PANEL, SET IN 2 CONT. BEADS OF SEALANT AND CAULKED VERTICALLY AT SEAMS SOLID DECK

27 side wall DETAIL FINISHED WALL 1. Apply sealant tape to inside of panel leg. 2. Attach sidewall flashing by installing fastener at 24 O.C. through sealant tape into panel 3. Install counter flashing. FASTENER SIDEWALL FLASHING BUTYL TAPE FASTENER AT 24 O.C. ML SERIES ROOF PANEL SOLID DECK

28 side wall DETAIL SEALANT 1. Apply sealant tape to inside of panel leg. 2. Attach sidewall flashing by installing fastener at 24 O.C. through sealant tape into panel 3. Install counter flashing and caulk with sealant. FASTENER AT 24 O.C. CONT. BUTYL TAPE COUNTER FLASHING SIDEWALL FLASHING BUTYL TAPE STITCH SCREW ML SERIES ROOF PANEL SOLID DECK

29 side wall DETAIL 1. Apply sealant tape to inside of panel leg. 2. Attach sidewall flashing by installing fastener at 24 O.C. through sealant tape into panel 3. Install counter flashing and caulk with sealant. SEALANT COUNTER FLASHING SIDEWALL FLASHING BUTYL TAPE FASTENER ML SERIES ROOF PANEL SOLID DECK

30 vent pipe flashing detail 1. Cut pipe boot at appropiate pipe diameter. 2. Slide the pipe boot down over the pipe using water to lubricate it of necessary. 4. Seal between base and roof with tube sealant. 5. Fasten the pipe boot with 1-1/2 woodscrew at 1-1/2 centers to complete the seal. 1-½" 1-½" Centers Pipe Boot

31 CURB DETAIL STEP 1 POLYSTICK MTS POLYGLASS NAILER BASE ISO BOARD ML SERIES ROOF PANELS

32 CURB DETAIL STEP 2 FASTENERS INSTALL CURB OVER SEALANT HIDDEN FASTENERS AREA DIRECT TO METAL DECK POLYSTICK MTS-POLYGLASS APPLY 3 LINES OF SEALANT FLAT SHEET GAUGE 24 FLASHING BASE 12 MIN REMOVE HALF OF FEMALE LEG 6 6 ML SERIES ROOF PANEL PANEL INSTALLATION DIRECTION TERMINATION BENDING LAP ON HIGH RIB, CUT ON SITE step 1 step 2 step 3 step

33 CURB DETAIL STEP 3 MECHANICAL LOCK PANEL HIDDEN FASTENERS DIRECT TO METAL DECK PANEL RIB COVER (OPTIONAL) APPLY 3 LINES OF SEALANT MECHANICAL LOCK PANEL 3/16 X 7/8 DOUBLE BEAD TAPE SEALANT 3/32 X 1 ROLL TAPE SEALANT MTS POLYGLASS

34 CURB DETAIL STEP 4 ML SERIES ROOF PANEL FASTENERS 1/4-14 x 1/4 LONG LIFE SELF TAPPING SCREWS PANEL RIB COVER (OPTIONAL) 3/16 X 7/8 DOUBLE BEAD TAPE SEALANT 3/32 X 1 ROLL TAPE SEALANT MTS POLYGLASS NOTE: THIS DETAIL APPLIES FOR RIGID INSULATION SYSTEM

35 ridge/hip cap RIDGE / HIP CAP FASTENERS, (5) PER PANEL BOX PANEL END SEALANT FASTENER, 12 O.C. FASTENERS, (5) PER PANEL BUTYL TAPE SEALANT BUTYL TAPE SEALANT ML SERIES PANEL METAL DECK

36 VALLEY WITH INTEGRAL CLEAT PLATE OR WOOD BLOCKING CAULK BETWEEN WEBS FILL PANEL HEM W/ BUTYL SEALANT ML SERIES PANEL FASTENER 12 0.C. 1-1/2 INSULATION METAL DECK VALLEY 12 OVERLAP

37 GUTTER ML SERIES ROOF PANEL PANCAKE FASTENERS, 12 O.C. BUTYL TAPE SEALANT CAULK BETWEEN WEBS FASTENER, 12 O.C. CLEAT 1-1/2 INSULATION EAVE FLASHING METAL DECK WOOD BLOCKING STRAP GUTTER

38 EAVE ML SERIES ROOF PANEL PANCAKE FASTENERS 12 O.C. CAULK BETWEEN WEBS BUTYL TAPE SEALANT INSULATION METAL DECK WOOD BLOCKING FASTENER 12 O.C. EAVE FLASHING CLEAT

39 eave 90 ML SERIES ROOF PANEL PANCAKE FASTENERS, 12 O.C. METAL DECK INSULATION FASTENER 12 O.C. WOOD BLOCKING CLEAT RAKE FLASHING

40 sidewall Z CLOSURE SET IN BUTYL TAPE SEALANT ATTACHED W/ (5) FASTENERS PER PANEL FASTENER, 12 O.C. BUTYL TAPE SEALANT ML SERIES ROOF PANEL BOX PANEL END SIDEWALL FLASHING SEALANT PANEL, BOX, PANEL END SD FASTENERS (3) PER PANEL SEALANT Z CLOSURE FASTENER, 12 O.C. BASE DRIP

41 RAKE RAKE FLASHING SEALANT ML SERIES ROOF PANEL BOX END OF PANEL FASTENERS, 12 O.C. Z CLOSURE WOOD BLOCKING 1-1/2 INSULATION

42 ENDWALL APPROVED SEALANT FASTENERS COUNTER FLASHING FASTENERS, 12 O.C. ENDWALL FLASHING SEALANT FASTENER 12 O.C. SEALANT ML SERIES PANEL Z CLOSURE BUTYL TAPE SEALANT FASTENERS, (5) PER PANEL WOOD BLOCKING 1-1/2 INSULATION METAL DECK

43 ENDWALL SEALANT FASTENER, 12 O.C. COUNTER FLASHING ENDWALL FLASHING FASTENER 12 O.C. SEALANT Z CLOSURE ATTACHED W/ (5) FASTENERS PER PANEL BUTYL TAPE SEALANT ML SERIES PANEL SEALANT COUNTER FLASHING FASTENERS, 12 O.C. ENDWALL FLASHING SEALANT FASTENER 12 O.C. BUTYL TAPE SEALANT SEALANT ML SERIES PANEL Z CLOSURE BUTYL TAPE SEALANT FASTENER (5) PER PANEL WOOD BLOCKING 1-1/2 INSULATION METAL DECK

44 ENDWALL SIDING FASTENERS, 12 O.C. ENDWALL FLASHING SEALANT FASTENER, 12 O.C. BUTYL TAPE SEALANT SEALANT ML SERIES PANEL Z- CLOSURE BUTYL TAPE SEALANT FASTENERS, (5) PER PANEL WOOD BLOCKING 1-1/2 INSULATION METAL DECK