Absco Space Saver Shed Assembly Instructions Model: 15081SK

Transcription

1 Assembly Instructons Model: 508SK FRONT BASE LENGTH:.52m SIDE BASE LENGTH: 0.78m FRONT WALL HEIGHT:.8m REAR WALL HEIGHT:.95m CONCRETE SLAB 620mm 880mm WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED EDGE 25mm DEEP AROUND THE PERIMETER THIS WILL HELP WATER EGRESS FROM THE BASE OF THE SHED CONCRETE 00mm BOTTOM REBATED EDGE 75mm WIDE REBATE CONCRETE SLAB We thank you for choosng an Australan made shed. For further assstance please vst our detaled nstructonal vdeo lbrary at At ABSCO Industres we are always lookng to be number ONE, so please let us know what you thnk of our nstructons. Feedback makes us better. feedback@absco.com.au ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE

2 GENERAL Absco Space Saver Shed Model: 508SK Before commencng any assembly, read through these nstructons n detal to gan a thorough understandng of assembly methods and assocated detals. Unpack the carton and carefully dentfy and check off all the parts aganst the parts descrbed and llustrated on pages three and four. SITE PREPARATION The ste for the shed must be level. An uneven surface may result n msalgnment of parts. It s recommended that the shed be set on a 00mm concrete slab and anchored down approprately (refer to last page for detals). Anchor sets are not suppled as standard tems wth ths product as some customers wsh to use ther own anchorng systems. TOOLS REQUIRED OPTIONAL A NOTE ON SAFETY Normal: 4mm & 0mm Masonry: 0mm Some parts may have sharp edges. It s advsable to wear gloves when handlng these tems and safety glasses f drllng holes. Sensble shoes are hghly recommended. Do not erect your shed n wndy condtons, ensure that the shed s securely anchored to a sold foundaton mmedately after constructon s completed. It s hghly recommended to erect the shed wth two or more people. ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 2

3 Model: 508SK COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 2 STEEL SHEET 95 X 773mm 43B WITH HINGES L = 725mm 58A STEEL SHEET 95mm X 773mm X4L 58B L = 725mm 53B STEEL SHEET 95mm X 773mm X2R 2 58C L = 773mm 53B 2 STEEL SHEET 865mm X 773mm 43D L = 53mm 8F 8F STEEL SHEET 785mm X 7mm 34A 2 L = 53mm 8E 8E STEEL SHEET 725mm X 773mm B L = 785mm 80A 80A 53A L = 53mm 53A 2 L = 786mm 6B 6B L = 53mm 53B 53B 2 L = 773mm 8J 8J L = 53mm 53C 53C L = 783mm 79C 79C ALL SHEETS HAVE PART NO.S LOCATED ON LOWER RIGHT OR UPPER LEFT CORNER OF COLORED SIDE AS SHOWN Part No. Here 2345 ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 3

4 Model: 508SK COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK Part No. Here JAMB L= 785mm 89A Part No. Here 2 9A JAMB L= 20mm Part No. Here JAMB L= 785mm 89B 2 88B 88B LIP TRIM L= 865mm Part No. Here JAMB L= 783mm 90C FITTINGS & ACCESSORIES PACKET CONTENTS DOOR STRAP 2A L: 65mm ASSEMBLY PSTKSGL SINGLE DOOR FITTINGS PACK PSTKSGL - SINGLE DOOR FITTINGS PACK DOOR PADBOLT FAST006 DOOR PADBOLT HASP FAST007 3mm DRILL BIT DRILL PHILLIPS DRIVER BIT FAST038 SELF TAPPING SCREWS PACKET CONTAINING 220 PACK 6P SCREW PACK 6 PACK 6P - SCREW PACK 6 6 3/6 COUNTERSUNK SCREWS & NUTS x 8mm BLIND POP RIVETS ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 4

5 Model: 508SK VIEW OF ROOF COMPONENTS 8E 43D 43D 88B 8E ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 88B PAGE 5 NO.

6 Model: 508SK 53C 43B X4L 43B 6B 34A X2R 90C 89A 8F 9A 89B 8J 79C VIEW OF WALL COMPONENTS 80A 53B ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 6B 22A 53A 8J B PAGE 6

7 Model: 508SK ABSCO ASSEMBLY INTRODUCTION The snaptte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners. To pre-assemble the four wall panels and two roof panels, the permeter channels are secured to the top and bottom of each panel usng the snaptte system, as detaled on the followng pages wherever you see the symbol. HIGH SIDE PUSH HIGH SIDE HIGH SIDE HIGH SIDE PUSH After jonng sheets together, poston channel over one end of the sheets, gently tappng t over the snaptte lugs, workng along the sheets to the other end. Poston sheets on tmbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS D PUSH HIGH SIDE Jon components together by pre-drllng the holes frst. Use one component as a template to mark where the holes are. Drll wth 3mm drll bt. Jon components together wth one screw at ths locaton only, as some channel sectons have extra holes that are not requred for ths model of garden shed Do not jon components together at ths locaton yet, as the screw may obstruct further assembly of other components ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 Each permeter channel must fnsh flush wth the edges of the sheets.the snaptte system allows adjustment for ths process by smply tappng the channel along the sheets untl each end s neatly flush. If you need to remove channels from the panels, pull the channel along the panel from opposng ends. You may need someone to help wth ths. 3mm POP RIVETS 4mm NUT & BOLT SET PAGE 7

8 Model: 508SK. REAR PANEL ASSEMBLY 43B 43B 53C 8F ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 8

9 Model: 508SK 2. SIDE PANEL ASSEMBLY (TWO REQUIRED) 6B 80A X2R X4L 8J Reverse sde of Door Mullon ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 9

10 Model: 508SK 3. ROOF ASSEMBLY 43D 43D 88B 8E 8E 88B ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 0

11 Model: 508SK DOOR 4. DOOR PANEL ASSEMBLY 58C 58A 58B B 2A 58C ALL VERTICAL DOOR S ARE INSTALLED IN THE REVERSE DIRECTION IN COMPARISON TO HORIZONTAL DOOR S 20mm FLANGE B 5mm FLANGE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE

12 Model: 508SK 5. FRONT PANEL ASSEMBLY 53A 34A 89A 53B 53A 89A 53A 90C 89A 90C 53A 89B 90C 90C 89B 79C 53A 90C 89B 53B 79C 79C 90C 79C 53B 89B ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 2

13 Model: 508SK 6. DOOR PANEL ASSEMBLY 9A B 9A B NOTE: NUTS AND BOLTS (SUPPLIED) MAY BE USED INSTEAD OF POP RIVETS (SUPPLIED) BY SIMPLY ENLARGING THE HINGE HOLE SETS IN THE JAMB USING A 4MM DRILL BIT NOTE: The two holes requred to connect the padbolt hasp for each door have not been pre-punched, to allow for proper algnment. poston each hasp centrally over the padbolt shaft, and drll 3mm holes and secure wth screws ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 3

14 Model: 508SK 7. PANEL CONSTRUCTION SIDE WALL PANEL S FIT INTO THE NOTCHED FRONT AND REAR WALL PANEL S X2R 80A 89B REPLACE PADBOLT HASP 0mm SCREWS WITH 20MM SCREWS CONNECT DOOR MULLION SECTIONS WITH SIX 20mm SCREWS ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 4

15 Model: 508SK FINAL CONSTRUCTION ANCHORING OF SHED LOCATION OF 8 CONCRETE ANCHORS - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 0mm HOLE INTO THE WALL SHEET BOLT & NUT STEEL ANGLE WALL SHEET SLAB - DRILL A 0mm HOLE INTO THE CONCRETE DYNABOLT ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 5

16 Model: 508SK AUSTRALIA PRODUCT WARRANTY AGAINST DEFECTS Congratulatons on your purchase of an ABSCO SHED ABSCO SHEDS, ncludng garden sheds, garden beds, avares, storage unts, garages, awnngs and carports are made usng hgh qualty Australan made steel. We are pleased to advse we warrant that the steel coatng wll not rust, crack, flake peel or blster for 30 years from date of purchase, when nstalled wthn Australa. Ths warranty does not apply to surface deteroraton of panels caused by 'Swarf (Tny partcles of steel debrs left from cuttng, grndng or drllng operatons) that has not been removed after buldng constructon, or as a result of contact wth damp sol, chemcals, fertlsers or other corrosve substances. Ths warranty covers any Absco product used for normal domestc use and nstalled n accordance wth the nstallaton nstructons. The warranty does NOT cover Damage caused by storms, wnd, ran snow or poor foundatons. Ths warranty does NOT cover ABSCO products nstalled n severe coastal, ndustral or other hghly corrosve envronments. The warranty does not cover fasteners (screws, nuts, bolts, rvets, hasps or sldng padbolts). The warranty s lmted to replacement and delvery of components and does not nclude any labour or nstallaton costs. The benefts gven by the warranty are n addton to your other rghts and remedes under a law n relaton to the goods or servces to whch the warranty relates. The warranty apples to the excluson of all other representatons, guarantees or warrantes express or mpled, our goods come wth guarantees that cannot be excluded under the Australan consumer law and s not transferable. You are enttled to a replacement or refund for a major falure and for compensaton for any other foreseeable loss or damage. You are also enttled to have the goods repared or replaced f the goods fal to be of an acceptable qualty and the falure does not amount to a major falure. For further nformaton go to Please retan a proof of purchase (sales docket or nvoce) or regster your warranty wthn 30 days of purchase here: In the unlkely event a warranty clam s made, t must be supported by photographc evdence and detals of the defect, ncludng component part numbers, together wth proof of purchase documentaton (or on-lne regstraton of purchase) and forwarded to the address below. Upon recept of the warranty clam, the Customer Servce Manager wll contact you wthn three busness days to advse you of the assessment outcome of the clam, whch may nclude your expenses ncurred n makng the clam. THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 9 ACACIA RIDGE QLD AUSTRALIA 40 PHONE: FAX: warranty@absco.com.au Issued 0 January 203 ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 6

17 Model: 508SK ABSCO SHEDS - STORAGE GUIDELINES ABSCO SHEDS nclude garden sheds, garden beds, storage unts, avares, garages, awnngs and carports. ABSCO SHEDS are desgned to be weatherproof for normal weather condtons. In the event of extreme weather condtons such as heavy ran, combned wth hgh wnd gusts, the rdge cappng, sheetng jons, screw fxngs etc., may exhbt mnor deformatons whch may allow some water entry. These areas should be checked regularly to ensure that maxmum strength and protecton s mantaned. Other weather condtons such as extreme heat and extreme cold, most or dry ar can nfluence the effects of concrete floor mosture and/or condensaton on the undersde of the roof sheets. ABSCO SHEDS and storage unts are prmarly used for storage of garden equpment such as lawnmowers, wheelbarrows, garden tools etc. Storage tems that mght be adversely affected by any of the above condtons may requre addtonal protecton such as beng sealed or covered by plastc sheets and/or stacked above the concrete floor on tmber slats. Waterproof sealants may be used to offer further protecton where requred around jons and screw fxngs, as can rubber door seals and other products whch are avalable from most hardware outlets. Placement of waterproof sealants (slcone) between the base of the shed and concrete slab s not recommended, as ths process can have a reverse effect, preventng excess water from escapng, resultng wth water accumulatng and beng trapped nsde the shed. Absco accepts no responsblty for water entry, floor mosture, condensaton or the condton of the Contents nsde your Absco steel buldng arsng from any of the pre-mentoned weather condtons. ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 508SK 23/0/7 PAGE 7