Microbarr Anti Bacterial Acrylic Eggshell

Transcription

1 Microbarr Anti Bacterial Acrylic Eggshell Johnstone s Microbarr Anti Bacterial Acrylic Eggshell is a high performance, tough acrylic resin based interior coating, formulated to assist in the fight against hospital acquired infections, caused by harmful bacteria. Formulated using Silver Ion technology, Johnstone s Microbarr is proven to actively inhibit MRSA and E-Coli over the painted surface. SPECIAL PROPERTIES Tough, durable Eggshell formulated to assist in the fight against infections caused by harmful bacteria. Brilliant White, Magnolia. Available in a range of colours via the Johnstone s tinting system. Eggshell Avoid the risk of spillage, always store and transport in a secure upright position. PROTECT FROM FROST. LOW % VOCs (Volatile Organic Compounds) contribute to atmospheric Wet: 83µm, dry: 30µm. SIZE 5 Litre. Developed using Silver Ion Technology to inhibit bacteria and provide a tough, washable finish. For interior use in areas of high traffic and when hygiene protection is required. 36% Touch dry in 1-2 hours. Recoatable after 3-4 hours. Johnstones Microbarr Anti-Bacterial Acrylic Matt will cover approximately 12 square metres per litre depending on the nature and porosity of the surface. If more than one can of a colour is to be used in the same area, intermix before use. All surfaces should be sound, clean, dry and free from grease. Remove any crazed or flaking paint. Rub down sound glossy surfaces with fine waterproof abrasive paper and rinse thoroughly before applying a pre-coat of Johnstones Acrylic Primer Undercoat. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during preparation of pre-1960s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory. Seal absorbent surfaces with a solution of up to 1 part water to 4 parts Anti-Bacterial Acrylic Matt. Prime bare timber and metal surfaces with an appropriate Johnstones primer. Allow radiators to cool before painting. For additional information and free Johnstones Trade datasheets call or visit suitable for application by spray. Seal absorbent surfaces with a coat of Anti-Bacterial Acrylic Eggshell thinned up to 10% with clean water. If more than one can of a colour is to be used in the same area, intermix before use. equipment before cleaning. Clean immediately after use in warm soapy water and rinse thoroughly. Replace lid firmly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty waste paint into drains or watercourses. Contains reaction mass of: 5-chloro-2-methyl-4-isothiazolin- 3-one (EC no ) and 2-methyl-2H-isothiazol-3-one (EC no ) (3:1), 1,2-benzisothiazol-3(2H)-one and octhilinone (ISO). May produce an allergic reaction. Keep out of reach of children Remove contact lenses, if present and easy to do. Continue rinsing.

2 Microbarr Anti Bacterial Acrylic Matt Johnstone s Microbarr Anti Bacterial Acrylic Matt is a high performance, tough acrylic resin based interior coating, formulated to assist in the fight against hospital acquired infections, caused by harmful bacteria. Formulated using Silver Ion technology, Johnstone s Microbarr is proven to actively inhibit MRSA and E-Coli over the painted surface. SPECIAL PROPERTIES Tough, durable Matt formulated to assist in the fight against infections caused by harmful bacteria. Brilliant White, Magnolia. Available in a range of colours via the Johnstone s tinting system. Matt Avoid the risk of spillage, always store and transport in a secure upright position. Protect from frost. LOW % VOCs (Volatile Organic Compounds) contribute to atmospheric Wet: 83µm, dry: 28µm. SIZE 5 Litre Developed using Silver Ion Technology to inhibit bacteria and provide a tough, washable finish. For interior use in areas of high traffic and when hygiene protection is required. 33.6% Johnstones Microbarr Anti-Bacterial Acrylic Matt will cover approximately 12 square metres per litre depending on the nature and porosity of the surface. If more than one can of a colour is to be used in the same area, intermix before use. Touch dry in 1-2 hours. Recoatable after 3-4 hours. All surfaces should be sound, clean, dry and free from grease. Remove any crazed or flaking paint. Rub down sound glossy surfaces with fine waterproof abrasive paper and rinse thoroughly before applying a pre-coat of Johnstones Acrylic Primer Undercoat. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during preparation of pre-1960s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory. Seal absorbent surfaces with a solution of up to 1 part water to 4 parts Anti-Bacterial Acrylic Matt. Prime bare timber and metal surfaces with an appropriate Johnstones primer. Allow radiators to cool before painting. For additional information and free Johnstones Trade datasheets call or visit Stir well before use and apply by brush, roller or paint pad. When using a roller, use a medium pile synthetic type. Do not overfill the tray. Ensure roller is loaded evenly. If using a brush, load generously. Apply liberally and evenly; avoid overspreading. equipment before cleaning. Clean immediately after use in warm soapy water and rinse thoroughly. Replace lid firmly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty waste paint into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one and octhilinone (ISO). May produce an allergic reaction. Keep out of reach of children Remove contact lenses, if present and easy to do. Continue rinsing.

3 Covaplus Vinyl Matt Matt. Johnstone s Covaplus Vinyl Matt Emulsion is formulated for interior use on walls and ceilings. It provides a durable finish that is resistant to fading. It has a longer wet edge time to help reduce flashing and patchy finishes on surfaces. Wood, metal and plaster. Also suitable for use on wallboards, concrete, cement rendering, brickwork and blockwork in internal situations. Over 15,500 colours are available via the Johnstone s a secure upright position. Protect from frost. Minimal VOC content % This product contains max 3g/l VOC. Wet: 90µm, dry: 24µm. Suitable for interior use on walls and ceilings. 27% Approximately square metres per litre depending on the nature and porosity of the surface. Recoatable after 2 4 hours Longer wet edge time to help reduce flashing and patchy finishes. Produces a wipeable finish. Excellent opacity and colour retention. EU Ecolabel accredited All surfaces to be painted should be clean, dry and free from loose and flaking material. Prime bare surfaces with the appropriate Johnstone s Primer. Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during surface preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory, on suitable for application by spray. Seal absorbent surfaces with a coat of Covaplus Vinyl Matt Emulsion thinned up to 10% with clean water. If more than one can of a colour is to be used in the same area, intermix before use. Do not apply in temperatures below 10 C. application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. If medical advice is needed, have product container or label at hand. Remove contact lenses, if present and easy to do. Continue rinsing. IF SWALLOWED: Call a POISON CENTRE or doctor if you feel unwell. 1 Litre, 2.5 Litre, 5 Litre, 10 Litre. 350ml testerpots available

4 Flat Matt Johnstone s Flat Matt is a high quality dead matt emulsion suitable for all interior walls and ceilings, providing a completely flat finish with excellent opacity, coverage and application. Wood, metal and plaster. Also suitable for use on wallboards, concrete, cement rendering, brickwork and blockwork in internal situations. Over 16,000 colours are available via the Johnstone s Johnstone s Flat Matt will cover approximately square metres per litre depending on the nature and porosity of the surface being painted. Low VOC Content % VOC s (Volatile Organic Compounds) contribute to atmospheric Wet: 90µm Dry: 24µm Interior walls and ceilings Matt 27% 2-4 Touch dry in 1-2 hours. Recoatable after 2-4 hours. a secure, upright position. Protect from frost. Fashionable dead flat matt finish Wide colour offer Excellent opacity All surfaces to be painted should be clean, dry and free from loose and flaking material. Prime bare surfaces with the appropriate Johnstone s Primer. Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. For additional information and free Johnstone s Trade datasheets call or visit suitable for application by spray. Seal absorbent surfaces with a coat of Flat Matt thinned up to 10% with clean water. If more than one can of a colour is to be used in the same area, intermix before use. Do not apply in temperatures below 10 C. application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. Dispose of contents to a Waste Disposal Site in accordance with local/national regulations. Do not breathe spray. Wear respiratory protection. Remove contact lenses, if present and easy to do. Continue rinsing. IF ON SKIN: wash with plenty of soap and water. Do not use solvent 2.5 Litre, 5 Litre.

5 Ultra High Opacity Matt Matt. Johnstone s Ultra High Opacity Matt is a high opacity emulsion designed to achieve the appearance of a two coat application in just one coat. It is water based and easy to use and dries to a tough hard wearing matt finish. Interior walls and ceilings. Over 7,000 colours are available via the Johnstone s 8 4 Avoid the risk of spillage, always store and transport in a secure upright position. Protect from frost. Suitable for interior use. Touch dry in 2 hours. Recoatable after 4 hours. Low VOC content % VOC s (Volatile Organic Compounds) contribute to atmospheric Wet: 100µm, dry: 31µm. 35% Approximately 8 square metres per litre depending on the nature and porosity of the surface. High opacity designed to achieve the appearance of a two-coat application in just one coat. Minimum application time. Ease of application. Ensure the surface to be painted is clean, dry and free from grease. Remove any loose flaking or powdery material. Rub down glossy surfaces with fine waterproof abrasive paper and rinse thoroughly to provide a key. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during surface preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory, on Stir well before use and apply by brush, roller or paint pad. For brush application, fully load the brush and apply liberally and evenly. Avoid overspreading. When using a medium pile roller or paint pad, apply generously and evenly. Do not apply in damp or cold conditions below 10 C. application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. If medical advice is needed, have product container or label at hand. Remove contact lenses, if present and easy to do. Continue rinsing. IF SWALLOWED: Call a POISON CENTRE or doctor if you feel unwell. 5 Litre.

6 Dry Lining Paint Johnstone s Dry Lining is a high quality flat matt emulsion specially formulated for application onto bare or primed/sealed Dry Lining boards. It s enhanced opacity and flat matt finish significantly reduces the appearance of surface imperfections in areas featuring critical lighting. It offers excellent coverage and application qualities with a drying time of 1-2 hours making the job easier to complete. Suitable for use on plasterboard/wallboards/dry lining boards Ceiling & walls. Available in over 6,000 colours via the Johnstone s Matt 27% Johnstone s Dry Lining will cover approximately square metres per litre depending on the nature and porosity of the surface being painted. 2-4 Touch dry in 1-2 hours. Recoatable after 2-4 hours. a secure, upright position. Protect from frost. Low VOC Content % VOC s (Volatile Organic Compounds) contribute to atmospheric EU limit value for this product (Cat A/a): 30g/l (2010) For use on bare or primed / sealed Dry Lining boards Hides surface imperfections highlighted by critical lighting Easy to touch up Touch dry in 1-2 hours All surfaces to be painted should be clean, dry and free from loose and flaking material. For additional information and free Johnstone s Trade datasheets call or visit suitable for application by spray. Seal new/bare surfaces with a coat of Dry Lining thinned up to 10% with clean water. Finish with two full coats of Dry Lining paint. Do not apply in temperatures below 10 C. Plasterboards which have been initially coated with the board manufacturers specified primer/ sealer should also be finish with two coats of Dry Lining paint. / AFTER USE application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. If medical advice is needed, have product container or label at hand. Dispose of contents to a Waste Disposal Site in accordance with local/national regulations. Do not breathe spray. Wear respiratory protection. Remove contact lenses, if present and easy to do. Continue rinsing. IF ON SKIN: wash with plenty of soap and water. Do not use solvent 10 Litre. Wet: 90µm Dry: 24µm

7 Endura Super Durable Matt Matt. Johnstone s Super Durable Matt offers ultimate durability, tested to over 10,000 scrubs. For use on interior walls and woodwork, it s tougher than Acrylic Eggshell, making it easier to clean and the ideal solution for high traffic areas. A fast drying, low odour dead flat matt finish ideal for use where durability and performance is important. Interior walls and ceilings. Suitably primed woodwork and radiators. Available in Brilliant White, Magnolia and L Base and over 7,000 colours are available via the Johnstone s Suitable for interior use. 35% Recoatable after 4 hours. 4 Approximately square metres per litre depending on the nature and porosity of the surface being painted. Ultimate durability and performance. Class 1 ISO11998 & Class C BS Scrub Rating. Ideal for high wear/traffic areas. Dead flat matt finish. All surfaces should be sound, clean, dry and free from grease. Remove any crazed or flaking paint. Rub down sound glossy surfaces with fine waterproof abrasive paper and rinse thoroughly before applying a pre-coat of Johnstones Joncryl Acrylic Primer Undercoat. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact PPG Extra. Seal absorbent surfaces with a solution of up to 1 part water to 4 parts Endura Super Durable Matt. Prime bare timber and metal surfaces with an appropriate Johnstones primer. Allow radiators to cool before painting. For additional information and free Johnstones Trade datasheets call or visit Stir well before use and apply by brush, roller or paint pad. Also suitable for applying by spray. When using a roller, use a medium pile synthetic type. Do not overfill the tray. Ensure roller is loaded evenly. If using a brush, load generously. Apply liberally and evenly; avoid overspreading. equipment before cleaning. Clean immediately after use in warm soapy water and rinse thoroughly. Replace lid firmly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty wastes paint into drains or watercourses. a secure upright position. Protect from frost. Low VOC content % This product contains max 15g/l VOC. Wet: 83µm, dry: 29µm. Contains 1,2-benzisothiazol-3(2H)-one and octhilinone (ISO). May produce an allergic reaction. Keep out of reach of children Do not get in eyes, on skin, or on clothing Remove contact lenses, if present and easy to do. Continue rinsing. IF ON SKIN: wash with plenty of water. Do not use solvent 5 Litre only.

8 Acrylic Durable Matt Matt. Johnstone s Acrylic Durable Matt is a premium quality emulsion formulated for interior use on walls and ceilings. In addition it can be used on suitably primed woodwork and radiators. This low odour paint is washable and wipeable, providing a tough finish that is resistant to condensation, yellowing and most household stains. Its outstanding durability makes it ideal for use in kitchens, bathrooms, hotels, hospitals and public buildings. Interior walls and ceilings. Suitably primed woodwork and radiators. Over 16,000 colours are available via the Johnstone s Recoatable after 4 hours. 4 a secure upright position. Protect from frost. Low VOC content % Wet: 83µm, dry: 28µm. Suitable for interior use. 33.6% Approximately square metres per litre depending on the nature and porosity of the surface being painted. Highly durable and washable. Resists stains. Retains a true matt finish. Meets Class 1 of ISO for scrub resistance. All surfaces should be sound, clean, dry and free from grease. Remove any crazed or flaking paint. Rub down sound glossy surfaces with fine waterproof abrasive paper and rinse thoroughly before applying a pre-coat of Johnstone s Joncryl Water Based Primer Undercoat. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Seal absorbent surfaces with a solution of up to 1 part water to 4 parts Acrylic Matt. Prime bare timber and metal surfaces with an appropriate Johnstone s primer. Allow radiators to cool before painting. Special precautions should be taken during preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory on Stir well before use and apply by brush, roller or paint pad. When using a roller, use a medium pile synthetic type. Do not overfill the tray. Ensure the roller is loaded evenly. If using a brush, load generously. Apply liberally and evenly; avoid overspreading. Also suitable for application by spray. Do not apply when air or surface temperature is less than 10 C or in damp conditions. If more than one can of colour is to be used in the same area, intermix before use. equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one and octhilinone (ISO). May produce an allergic reaction. If medical advice is needed, have product container or label at hand Keep out of reach of children Do not get in eyes, on skin, or on clothing Remove contact lenses, if present and easy to do. Continue rinsing. 2.5 Litre, 5 Litre and 10 Litre* * 10L available in BW and Magnolia only

9 Jonmat Premium Contract Matt Johnstone s Jonmat is a premium quality contract matt emulsion formulated for interior use on walls and ceilings. It provides an obliterating, permeable finish that is ideal for new plaster. Suitable for interior use. New plaster. Also suitable for use on aged plaster, wall boards, concrete, cement rendering, brickwork and blockwork in internal situations. Over 7,000 colours are available via the Johnstone s Matt a secure upright position. Protect from frost. Minimal VOC content % This product contains max 3g/l VOC. Wet: 90µm, dry: 21µm. 23% Approximately square metres per litre, depending on the nature and porosity of the surface. Recoatable after 2 4 hours. A premium obliterating matt contract emulsion for interior use. Specially formulated for use on new plaster allowing the substrate to breathe. Combines quality and economy. EU Ecolabel accredited All surfaces to be painted should be clean, dry and free from loose and flaking material. Prime bare surfaces with the appropriate Johnstone s Primer. Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during surface preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory, on suitable for application by spray. Seal absorbent surfaces such as new plaster with a coat of Jonmat thinned up to 20% with clean water. If more than one can of a colour is to be used in the same area, intermix before use. Do not apply in temperatures below 10 C. application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one and 2-methyl-2Hisothiazol-3-one. May produce an allergic reaction. Do not breathe spray. Wear respiratory protection. Remove contact lenses, if present and easy to do. Continue rinsing. 5 Litre, 10 Litre, 15 Litre.

10 Acrylic Eggshell Johnstone s Acrylic Eggshell is a premium quality, water-based, mid sheen finish formulated for interior use on walls, ceilings, wood and metal work. It provides a low odour, quick drying finish that is resistant to condensation and yellowing, making it ideal for use in kitchens, bathrooms, hospitals, hotels, foodstores, bakeries and public buildings. Wood, metal and plaster. Also suitable for use on wallboards, concrete, cement rendering, brickwork and blockwork in internal situations. Over 16,000 colours are available via the Johnstone s Mid sheen Avoid the risk of spillage, always store and transport in a secure upright position. Protect from frost. Low VOC content % Wet: 83µm, dry: 30µm. Suitable for interior use. 36% Approximately square metres per litre depending on the nature and porosity of the surface. Recoatable after 3 4 hours. A quick drying, low odour, mid sheen finish for interior use. Produces a smooth, washable surface that resists condensation. Tough, durable and non-yellowing. Meets Class 1 of ISO for scrub resistance. All surfaces to be painted should be clean, dry and free from loose and flaking material. Prime bare surfaces with the appropriate Johnstone s Primer. Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly before applying a pre-coat of Johnstone s Joncryl Water Based Primer Undercoat. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during surface preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory, on Stir well. Easy to apply by brush or roller. Seal absorbent surfaces with a coat of Acrylic Eggshell thinned up to 10% with clean water. If more than one can of a colour is to be used in the same area, intermix before use. Do not apply in temperatures below 10 C. application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains reaction mass of: 5-chloro-2-methyl-4-isothiazolin-3- one (EC no ) and 2-methyl-2H-isothiazol-3-one (EC no ) (3:1), octhilinone (ISO) and 1,2-benzisothiazol- 3(2H)-one,. May produce an allergic reaction. Remove contact lenses, if present and easy to do. Continue rinsing. 2.5 Litre, 5 Litre.

11 Vinyl Silk Johnstone s Vinyl Silk Emulsion is formulated for interior use on walls and ceilings. It provides a durable sheen finish that is easy to clean and resistant to fading. Suitable for interior use. Plaster and embossed wallcoverings. Also suitable for use on wallboards, concrete, cement rendering, brickwork and blockwork in internal situations. Over 16,000 colours are available via the Johnstone s Silk a secure upright position. Protect from frost. Low VOC content % EU limit value for this product (Cat A/b): 100g/l (2010). This product contains max 80g/l VOC. Wet: 91µm, dry: 28µm. 31% Approximately square metres per litre, depending on the nature and porosity of the surface. Recoatable after 3 4 hours. A high quality vinyl silk finish for interior walls and ceilings. Produces a washable surface. Especially suitable for embossed wallcoverings and areas where easy maintenance is required. All surfaces to be painted should be clean, dry and free from loose and flaking material. Prime bare surfaces with the appropriate Johnstone s Primer. Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during surface preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory, on suitable for application by spray. Seal absorbent surfaces with a coat of Vinyl Silk thinned up to 10% with clean water. If more than one can of a colour is to be used in the same area, intermix before use. Do not apply in temperatures below 10 C. application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. Keep out of reach of children accordance with local/national regulations Do not get in eyes, on skin, or on clothing Remove contact lenses, if present and easy to do. Continue rinsing. 1 Litre, 2.5 Litre, 5 Litre, 10 Litre.

12 Vinyl Soft Sheen Johnstone s Soft Sheen is a premium quality vinyl mid sheen emulsion formulated for interior use on walls and ceilings. It provides an attractive modern alternative to traditional Vinyl Silk and Vinyl Matt that will withstand normal levels of humidity and can be wiped clean. Plaster and embossed wallcoverings. Also suitable for use on wallboards, concrete, cement rendering, brickwork and blockwork etc. Over 16,000 colours are available via the Johnstone s Mid sheen a secure upright position. Protect from frost. Low VOC content % Wet: 90µm, dry: 25µm. Suitable for interior use. 28% Approximately square metres per litre depending on the nature and porosity of the surface. Recoatable after 3 4 hours. A subtle vinyl mid sheen finish alternative to Vinyl Matt and Vinyl Silk. Suitable for use on interior walls and ceilings. Easy to apply, washable and dirt resistant. All surfaces to be painted should be clean, dry and free from loose and flaking material. Prime bare surfaces with the appropriate Johnstone s Primer. Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during surface preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory, on suitable for application by spray. Seal absorbent surfaces with a coat of Soft Sheen thinned up to 10% with clean water. If more than one can of a colour is to be used in the same area, intermix before use. Do not apply in temperatures below 10 C. application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. accordance with local/national regulations Do not get in eyes, on skin, or on clothing Remove contact lenses, if present and easy to do. Continue rinsing. 1 Litre, 2.5 Litre, 5 Litre, 10 Litre.

13 Acrylic Satin Acrylic Satin is a premium quality satin sheen finish that is suitable for interior and exterior use on wood and suitably primed metal surfaces. It provides a low odour, high opacity finish that is quick drying and non-yellowing. Wood and metal. Over 16,000 colours are available via the Johnstone s Satin. 12 Suitable for interior and exterior use. * Recoatable after 4 hours. 4 35% Approximately 12 square metres per litre depending on the nature and porosity of the surface. a secure upright position. Protect from Frost. Medium VOC content % VOC s (Volatile Organic Compounds) contribute to atmospheric EU limit value for this product (Cat A/d): 130g/l (2010). This product contains max 130g/l VOC. Non yellowing. High opacity. Quick drying. Low odour satin finish. All surfaces to be painted should be clean, dry and free from loose and flaking material. Rub down sound glossy surfaces with fine waterproof abrasive paper and rinse thoroughly before applying a pre-coat of Johnstone s Acrylic Primer Undercoat. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Treat knots with Knotting Solution and prime exposed wood and metal with an appropriate primer. Special precautions should be taken during surface preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory, on Stir well before use and apply by brush or roller. Apply liberally and evenly for a smooth finish. Two coats are recommended under most conditions. Do not apply in temperatures below 10 C or in damp conditions. Remove as much paint as possible from application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Avoid contact with skin and eyes. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. After contact with skin, wash immediately with plenty of soap and water or a recognised skin cleaner. Keep out of the reach of children. Safety data sheet available for professional user on request. 1 Litre, 2.5 Litre, 5 Litre. Wet: 80µm, dry: 28µm.

14 Joncryl Water Based Primer Undercoat Johnstone s Joncryl is a high quality, acrylic resin based combined primer and undercoat formulated for interior and exterior use on new or bare wood, plaster, hardboard, cement and brickwork. It provides a low odour, quick drying, high opacity alternative to solvent-based primer and undercoat. A great undercoat for use under acrylic trim finishes. Suitable for interior and exterior use. Wood, plaster, concrete, cement rendering, brickwork and blockwork. Brilliant White Not applicable. a secure upright position. Protect from frost. Minimal VOC content % EU limit value for this product (Cat A/d): 130g/l (2010). This product contains max 3g/l VOC. Wet: 77µm, dry: 24µm. 32% Approximately square metres per litre, depending on the nature and porosity of the surface. 1-2 Touch dry in 1 hour. Recoatable after 1 2 hours. Quick drying, low odour application. Suitable for interior and exterior use on wood, plaster and masonry. A water-borne combined primer and undercoat based on a high quality acrylic resin. All surfaces to be painted should be clean, dry and free from loose and flaking material. Prime bare metal surfaces with the appropriate Johnstone s Primer. Rub down previously painted surfaces with fine waterproof abrasive paper and rinse thoroughly. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. Special precautions should be taken during surface preparation of pre-1960 s paint surfaces over wood and metal as they may contain harmful lead. For further advice contact Technical Advisory, on suitable for application by spray. Do not apply in temperatures below 10 C or externally when rain is imminent. application equipment before cleaning. Replace lid firmly. Clean equipment immediately after use with warm soapy water and rinse thoroughly. Some local authorities have special facilities for the disposal of waste coatings. Do not empty product into drains or watercourses. Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. Do not breathe spray. Wear respiratory protection. Remove contact lenses, if present and easy to do. Continue rinsing. 1 Litre, 2.5 Litre, 5 Litre.