42'-135' X Series Ladder, Cage and Platform

Transcription

1 42'-135' X Series Ladder, Cage and Platform Assembly Instructions PNEG-1773 Version: 2.3 Date: PNEG-1773

2 All information, illustrations, photos and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice. 2 PNEG '-135' X Series Ladder, Cage and Platform

3 Table of Contents Contents Chapter 1 Introduction...4 Chapter 2 Safety...5 Safety Guidelines... 5 Cautionary Symbols Definitions... 6 Safety Cautions... 7 Safety Sign-Off Sheet... 9 Proper Storage of Grain Bin/Silo Materials Prior to Construction Chapter 3 Decals...11 Chapter 4 Assembly Instructions '-135' Ladder Eave Platform Assembly Ladder Eave Platform Package...14 Platform and Safety Cage Bar...15 Platform and Wall Brace...16 Platform and Handrail Package...18 Platform and Swing Gate Package...19 Platform Ladder Bracket Package - Left Hand Side Assembly...21 Platform Ladder Bracket Package - Right Hand Side Assembly...23 Platform and Safety Cage Package...25 Platform and Safety Cage Splice Bracket...26 Platform Inside Post Bracket '-135' Ladder Only Eave Platform Package with Manway Guard '-60' Ladder Eave Platform Assembly Ladder Eave Platform Package...34 Platform and Safety Cage Bar...36 Platform and Handrail Package...37 Platform and Swing Gate Package...39 Platform Ladder Bracket Package...40 Platform and Safety Cage Package '-60' Ladder Only Eave Platform Assembly Ladder and Safety Cage Assembly Ladder and Safety Cage Layout " Commercial Ladder Offset and Platform Layout...49 Left Hand Side Ladder Assembly...53 Right Hand Side Ladder Assembly...54 X Series Ladder Intermediate Platform Package Platform Package...62 Platform and Safety Cage Bar Package...65 Platform and Ladder Cage Package...66 Platform and Cage Package...67 X Series Sidedraw Ladder Platform Package Platform Package...70 Platform and Safety Cage Bar Package...71 Platform and Handrail Package...72 Platform and Swing Gate Package...73 Platform and Safety Cage Package...74 Platform Ladder Bracket Package...75 Chapter 5 Parts List '-135' Ladder Eave Platform Assembly '-60' Ladder Eave Platform Assembly X Series Ladder Intermediate Platform Package X Series Sidedraw Ladder Platform Package Chapter 6 Warranty...93 PNEG '-135' X Series Ladder, Cage and Platform 3

4 1. Introduction READ THIS MANUAL carefully to learn how to properly use and install equipment. Failure to do so could result in personal injury or equipment damage. INSPECT the shipment immediately upon arrival. The customer is responsible for ensuring that all quantities are correct. The customer should report and note any damage or shortage on the bill of lading to justify their claim to the transport company. THIS MANUAL SHOULD BE CONSIDERED a permanent part of your equipment and should be easily accessible when needed. This warranty provides you the assurance that the company will back its products when defects appear within the warranty period. In some circumstances, the company also provides field improvements, often without charge to the customer, even if the product is out of warranty. Should the equipment be abused, or modified to change its performance beyond the factory specifications, the warranty will become void and field improvements may be denied. 4 PNEG '-135' X Series Ladder, Cage and Platform

5 2. Safety Safety Guidelines Safety guidelines are general-to-specific safety rules that must be followed at all times. This manual is written to help you understand safe operating procedures and problems that can be encountered by the operator and other personnel when using this equipment. Save these safety guidelines for future reference. As owner or operator, you are responsible for understanding the requirements, hazards, and precautions that exist and to inform others as required. Unqualified persons must stay out of the work area at all times. Alterations must not be made to the equipment. Alterations can produce dangerous situations resulting in SERIOUS INJURY or DEATH. This equipment must be installed in accordance with the current installation codes and applicable regulations, which must be carefully followed in all cases. Authorities having jurisdiction must be consulted before installations are made. When necessary, you must consider the installation location relative to electrical, fuel and water utilities. Personnel operating or working around equipment must read this manual. This manual must be delivered with equipment to its owner. Failure to read this manual and its safety instructions is a misuse of the equipment. ST PNEG '-135' X Series Ladder, Cage and Platform 5

6 2. Safety Cautionary Symbols Definitions Cautionary symbols appear in this manual and on product decals. The symbols alert the user of potential safety hazards, prohibited activities and mandatory actions. To help you recognize this information, we use the symbols that are defined below. DANGER WARNING CAUTION NOTICE This symbol indicates an imminently hazardous situation which, if not avoided, will result in serious injury or death. This symbol indicates a potentially hazardous situation which, if not avoided, can result in serious injury or death. This symbol indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury. This symbol is used to address practices not related to personal injury. This symbol indicates a general hazard. This symbol indicates a prohibited activity. This symbol indicates a mandatory action. ST PNEG '-135' X Series Ladder, Cage and Platform

7 2. Safety Safety Cautions Use Personal Protective Equipment Use appropriate personal protective equipment: Eye Protection Respiratory Protection Foot Protection Hearing Protection Head Protection Fall Protection Hand Protection Wear clothing appropriate to the job. Remove all jewelry. Tie long hair up and back. ST Follow Safety Instructions Carefully read all safety messages in this manual and safety signs on your machine. Keep signs in good condition. Replace missing or damaged safety signs. Be sure new equipment components and repair parts include the current safety signs. Replacement safety signs are available from the manufacturer. Learn how to operate the machine and how to use controls properly. Do not let anyone operate without instruction. If you do not understand any part of this manual or need assistance, contact your dealer. ST Maintain Equipment and Work Area Understand service procedures before doing work. Keep area clean and dry. Never service equipment while it is operating. Keep hands, feet, and clothing away from moving parts. Keep your equipment in proper working condition. Replace worn or broken parts immediately. ST PNEG '-135' X Series Ladder, Cage and Platform 7

8 2. Safety Sharp Edge Hazard This product has sharp edges, which can cause serious injury. To avoid injury, handle sharp edges with caution and always use proper protective clothing and equipment. ST Fall Hazard Keep access door closed while on a platform to avoid falls. Always use proper personal protective equipment and proper clothing when using equipment. Failure to follow safety precautions can result in severe injury or death. ST Fall Hazard Ladders, stairways and platforms are for use by competent and trained personnel only. Do not allow children or other unauthorized persons to have access to the equipment. Access to the equipment must be restricted by the use of security fencing and lockable gates. Lower sections of ladders must be fitted with a lockable safety gate to prevent unauthorized access. Make sure that hot surfaces have had adequate time to cool before working on or in the equipment. Lock out and tag out power supplies and fuel supplies to all equipment. Do not attach lifting equipment to ladders or platforms. Do not go outside of the safety rails provided on elevated platforms. Do not work at heights during high winds, rain, snow, or ice storms. ST PNEG '-135' X Series Ladder, Cage and Platform

9 2. Safety Stay Clear of Hoisted Equipment Always use proper lifting or hoisting equipment when assembling or disassembling equipment. Do not walk or stand under hoisted equipment. Always use sturdy and stable supports when needed for installation. Not following these safety precautions creates the risk of falling equipment, which can crush personnel and cause serious injury or death. ST Safety Sign-Off Sheet Below is a sign-off sheet that can be used to verify that all personnel have read and understood the safety instructions. This sign-off sheet is provided for your convenience and personal record keeping. Date Employee Name Supervisor Name ST-0007 PNEG '-135' X Series Ladder, Cage and Platform 9

10 2. Safety Proper Storage of Grain Bin/Silo Materials Prior to Construction Wet storage stain (rust) will develop when closely packed bundles of galvanized material, such as sidewall and roof sheets, have moisture present. Inspect roof and sidewall bundles on arrival for any moisture. If moisture is present, it must not be allowed to remain between the sheets. Separate the sheets or panels immediately and wipe them down. Spray with a light oil or diesel fuel. If possible, sidewall bundles, roof sheets and other closely packed galvanized materials should be stored in a dry, climate controlled building. If outdoor storage is unavoidable, the materials should be stored so that they are raised above the ground and vegetation. Any stacking and spacing materials should not be corrosive or wet. Be sure to protect materials from the weather, but permit air movement around the bundles if possible. Storing roof bundles and sidewall sheets at a slight incline can also help minimize the presence of moisture. Storing the bundles with the center of the dome up (like an arch) is one option for minimizing moisture during storage. Sidewall bundles can also be stored on edge but must be secured so that they do not fall over and cause injury. If white rust or wet storage stain occurs, contact the manufacturer immediately about ways to minimize the adverse effect upon the galvanized coating. 10 PNEG '-135' X Series Ladder, Cage and Platform

11 3. Decals The safety decals on your equipment are safety indicators which must be carefully read and understood by all personnel involved in the installation, operation, service and maintenance of the equipment. To replace a damaged of missing decal, contact us to receive a free replacement. GSI Decals 1004 E. Illinois St. Assumption, IL Phone: Location Decal # Decals Description CAUTION Located next to aeration system. DC-969 Caution Vacuum Pressure Excessive vacuum (or pressure) may damage roof. Use positive aeration system. Make sure all roof vents are open and unobstructed. Start roof fans when supply fans are started. Do not operate when conditions exist that may cause roof vent icing. GSI Group, Inc DC-969 PNEG '-135' X Series Ladder, Cage and Platform 11

12 3. Decals Location Decal # Decals Description DANGER On bin door covers DC-GBC-1A Rotating flighting will kill or dismember. Flowing material will trap and suffocate. Crusted material will collapse and suffocate. Keep clear of all augers. DO NOT ENTER this bin! Danger Keep Clear of Augers If you must enter the bin: 1. Shut off and lock out all power. 2. Use a safety harness and safety line. 3. Station another person outside the bin. 4. Avoid the center of the bin. 5. Wear proper breathing equipment or respirator. Failure to heed these warnings will result in serious injury or death. GSI GROUP, INC DC-GBC-1A WARNING On bin door covers DC-GBC-2A UNLOADING INSTRUCTIONS: Warning Unload Instructions 1. Use CENTER FLOOR OUTLET ONLY until NO grain remains above this outlet. 2. Side floor outlets to be used ONLY when above condition is satisfied. 3. Lock all side floor outlets to avoid accidental premature use. 4. See manufacturers instructions for proper use of factory supplied sidedraw (wall) discharge systems. Failure to heed these warnings could result in serious injury, death, structural damage or collapse of tank. GSI GROUP, INC DC-GBC-2A 12 PNEG '-135' X Series Ladder, Cage and Platform

13 72'-135' Ladder Eave Platform Assembly Instructions PNEG '-135' X Series Ladder, Cage and Platform 13

14 4. Assembly Instructions 72'-135' Ladder Eave Platform Assembly Ladder Eave Platform Package 1. Figure 4A shows the assembly of the platform supports. Use 5/16" hardware at all the connection points. (Platform floor will have to be attached at the same time as support angles.) NOTE: When installing the top wind ring, do NOT use the top set of holes in the stiffener. 2. Figure 4A shows the assembly of the platform floor system. This must all be assembled at the same time using 5/16" hardware. NOTE: Leave all hardware loose until completely assembled. 3. Left platform bracket must line up with stiffener, roof rib and rafter or beam if present in roof. Figure 4A Ref # Part # Description A STX-0014 Platform Toe Plate B STX-0011 Platform Short Angle (3) C STX-0081 X Series Platform Long Angle (2) D STX-0082 X Series Platform Bracket - Right E STX-0009 X Series Platform Bracket - Left F STX-0080 Single Piece Platform Floor G Place brackets in top sidewall ring H Attach at stiffener to sidewall connection. See note above about wind rings. I Use 5/16"-18 x 3/4" truss bolt (S-10267) and 5/16"-18 flange nut (S-10268) to attach platform floor and all substructure. 14 PNEG '-135' X Series Ladder, Cage and Platform

15 Platform and Safety Cage Bar 4. Assembly Instructions 4. Figure 4B shows the assembly of the platform post and post supports. This must all be assembled at the same time using 5/16" hardware. Figure 4B Ref # Part # Description A STX-0076 Eave Platform Corner Post B STX-0015 Platform Corner Post. Three (3) per 72'-135' eave platform. C D E LDR-5171 LDR " Safety Cage Bar. Two (2) per 72'-135' eave platform. Attach using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). The end that mounts to the platform angle will be outside of the toe kick. The end that mounts to the post will be inside of the toe kick plate. Eave Platform Post Support. One piece assembled under the platform to reinforce the platform corner. This piece mounts to both the platform short angle and the platform long angle. Attach using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach all handrail posts to platform using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). PNEG '-135' X Series Ladder, Cage and Platform 15

16 4. Assembly Instructions Platform and Wall Brace 5. Assemble the eave platform wall braces to the platform support and sidewall using 5/16" hardware. (See Figure 4C below and Figure 4D on Page 17.) Figure 4C Ref # A B Description Attach eave platform wall bracket to X series platform bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach at sidewall using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Wall brace should be as flat to sidewall as possible. Eave Platform Wall Brace (LDR-5206). Two (2) pieces bolted back to back. Length of bolted brace adjusted based on diameter to tank. 16 PNEG '-135' X Series Ladder, Cage and Platform

17 4. Assembly Instructions Platform and Wall Brace (Continued) Figure 4D Ref # Part # Description A STX-0323 X Series Eave Platform Left Outer and Inner Right Post Brace (N/S) B STX-0324 X Series Eave Platform Right Outer Post Brace C D Attach platform post brace using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Post braces attach to both the platform short angle and the platform corner post. The post brace sits inside of the platform short angle and on the outer side of the platform corner post. PNEG '-135' X Series Ladder, Cage and Platform 17

18 4. Assembly Instructions Platform and Handrail Package 6. Figure 4E shows the assembly of the platform handrails. These must also be attached using 5/16" hardware. Figure 4E Ref # Part # Description A LDR-4087 Large Intermediate Handrail (2). Field cut to fit. B STX-0038 Platform Handrail Short C STX-0075 Eave Platform Top Rail - Long D LDR-4088 Small Intermediate Handrail (2). Field cut to fit. E Attach upper handrails to platform posts using 5/16" x 2" bolt (S-7877) and 5/16"-18 flange nut (S-10268). F Attach intermediate handrails to platform posts using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). G Place self-drilling screw on bottom at overlap. H STX /4" - Eave Platform Top Rail - Long I STX /4" - Platform Handrail - Short 18 PNEG '-135' X Series Ladder, Cage and Platform

19 4. Assembly Instructions Platform and Swing Gate Package 7. Attach the platform gate bracket to the gate before attaching it to the inside platform post using 5/16" hardware. (See Figure 4F below and Figure 4G on Page 20.) Figure 4F Ref # Part # Description A LDR-5218 Ladder Safety Gate B LDR-5185 Intermediate Platform Gate Bracket C D E F Attach safety gate assembly to intermediate platform gate bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). When mounting the intermediate platform gate bracket, use the top and bottom holes. Swing gate should swing inward to the platform. Attach intermediate platform gate bracket to platform corner post using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). PNEG '-135' X Series Ladder, Cage and Platform 19

20 4. Assembly Instructions Platform and Swing Gate Package (Continued) Figure 4G Ref # A B Description Bottom view of assembled eave platform for 72'-135' and its relation to the stiffeners and sidewall. Top view of assembled eave platform for 72'-135' and its relation to the stiffeners and sidewall. C Distance between the bottom of the platform wall bracket and the horizontal seam is approximately 4". D Distance between the platform wall bracket notch and the horizontal seam is approximately 4.920". E Left hand side view of assembled eave platform for 72'-135' and its relation to the stiffeners and sidewall. 20 PNEG '-135' X Series Ladder, Cage and Platform

21 Platform Ladder Bracket Package - Left Hand Side Assembly 4. Assembly Instructions 8. Attach the wall angle to the sidewall sheet using the hole 9-3/8" from the stiffener hole pattern with 3/8" hardware. Assemble the wall bracket to the wall angle with 3/8" hardware and tighten. (See Figure 4H below and Figure 4I on Page 22.) Attach left and right intermediate platform ladder bracket to the wall bracket and platform support with 5/16" hardware. NOTE: Do not force the wall bracket in or out. Assemble the ladder and ladder brackets to the wall bracket using 5/16" hardware. The top ladder rung must be level with the platform floor. Figure 4H Ref # Part # Description A LDR-5178 Intermediate Platform Ladder Bracket - Left B LDR-5177 Intermediate Platform Ladder Bracket - Right C LDR-5174 Intermediate Platform Bracket - Left D E F Attach ladder sidewall angle (LDR-5168) to bin wall here 9-3/8" from platform wall bracket. Use 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach intermediate platform ladder to platform wall bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach ladder sidewall angle (LDR-5168) to platform wall bracket using 3/8-16" x 1" flange bolt (S-7485) and 3/8"-16 flange nut (S-9426). G 9-3/8" PNEG '-135' X Series Ladder, Cage and Platform 21

22 4. Assembly Instructions Platform Ladder Bracket Package - Left Hand Side Assembly (Continued) Figure 4I Ref # Part # Description A B C D 4FOOTRF LDR ' Roll Formed Ladder. Attach 4' roll formed ladder to intermediate platform ladder bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Eave Platform Ladder Bracket. Two (2) parts bolted back to back. Length of bolted parts dependent on bin diameter. Attach ladder stand off to wall bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach ladder stand off to platform bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). The Figure 4I shown with platform pan, post, handrails and safety gate hidden. 22 PNEG '-135' X Series Ladder, Cage and Platform

23 Platform Ladder Bracket Package - Right Hand Side Assembly 4. Assembly Instructions 9. Attach the wall angle to the sidewall sheet using the hole 9-3/8" from the stiffener hole pattern with 3/8" hardware. Assemble the wall bracket to the wall angle with 3/8" hardware and tighten. (See Figure 4J below and Figure 4K on Page 24.) Attach left and right intermediate platform ladder bracket to the wall bracket and platform support with 5/16" hardware. NOTE: Do not force the wall bracket in or out. Assemble the ladder and ladder brackets to the wall bracket using 5/16" hardware. The top ladder rung must be level with the platform floor. Figure 4J Ref # Part # Description A LDR-5178 Intermediate Platform Ladder Bracket - Left B LDR-5177 Intermediate Platform Ladder Bracket - Right C LDR-5173 Intermediate Platform Bracket - Right D E F Attach ladder sidewall angle (LDR-5168) to bin wall here 9-3/8" from platform wall bracket. Use 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach ladder sidewall angle (LDR-5168) to platform wall bracket using 3/8-16" x 1" flange bolt (S-7485) and 3/8"-16 flange nut (S-9426). Attach intermediate platform ladder to platform wall bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). G 9-3/8" PNEG '-135' X Series Ladder, Cage and Platform 23

24 4. Assembly Instructions Platform Ladder Bracket Package - Right Hand Side Assembly (Continued) Figure 4K Ref # Part # Description A B C D 4FOOTRF LDR ' Roll Formed Ladder. Attach 4' roll formed ladder to intermediate platform ladder bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Eave Platform Ladder Bracket. Two (2) parts bolted back to back. Length of bolted parts dependent on bin diameter. Attach ladder stand off to platform bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach ladder stand off to wall bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). The Figure 4K shown without platform pan, post, handrail and safety gate. 24 PNEG '-135' X Series Ladder, Cage and Platform

25 Platform and Safety Cage Package 4. Assembly Instructions 10. Attach the ladder flare to the ladder using 5/16" hardware. You must drill the bottom hole through the ladder and use 5/16" hardware. (See Figure 4L.) 11. Attach the cage hoops and cage splice brackets to the ladder flares and platform posts. This must all be assembled at the same time using 5/16" hardware. NOTE: Be sure the ladder flares are vertical and parallel to the platform posts by adjusting the splice brackets. The ladder will NOT be square to the platform due to the radius of the bin. The side closest to the bin wall will be closer to the platform. Figure 4L Ref # Part # Description A LDR-5218 Ladder Safety Gate B LDR-5167 Safety Cage Hoop Splice (2) C LDR-5164 Safety Cage Hoop - Standard (4) D LDR-5493 Formed Ladder Flare (2) E F G Attach safety cage hoop to formed ladder flare using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach safety cage hoop splice to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). This hole must be drilled through ladder on right and left sides. PNEG '-135' X Series Ladder, Cage and Platform 25

26 4. Assembly Instructions Platform and Safety Cage Splice Bracket 12. Attach the cage splice bracket to the post and cage splice using 5/16" hardware. (See Figure 4M.) Figure 4M Ref # Part # Description A LDR-5204 Safety Cage Splice Bracket B LDR-5167 Safety Cage Hoop Splice C D Attach safety cage splice bracket to handrail post using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach safety cage hoop splice to platform post or safety cage splice bracket. Mounting location is dependent on diameter of tank. 26 PNEG '-135' X Series Ladder, Cage and Platform

27 4. Assembly Instructions Platform Inside Post Bracket 13. Attach the post bracket to the inside post and bottom stair post using 5/16" hardware. (See Figure 4N.) NOTE: Continue to Page 48 to see remaining ladder and cage layout. Figure 4N Ref # Part # Description A STX-0076 Eave Platform Corner Post B LDR-5207 Eave Platform Inside Post Bracket C D Attach eave platform inside post bracket to platform corner post using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Field drill holes in roof stair post. Attach using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). PNEG '-135' X Series Ladder, Cage and Platform 27

28 NOTES 28 PNEG '-135' X Series Ladder, Cage and Platform

29 72'-135' Ladder Only Eave Platform Assembly Instructions PNEG '-135' X Series Ladder, Cage and Platform 29

30 4. Assembly Instructions Special Order Package Only 72'-135' Ladder Only Eave Platform Package with Manway Guard NOTE: Used when there are no roof stairs. 1. Attach ladder/eave platform handrail bracket (LDR-5304) and ladder/eave platform kick plate splice plate (LDR-5305) to eave handrail post (STX-0076) using 5/16" hardware. LDR-5207 will not be used in this package. (See Figure 4O below and Figure 4P on Page 31.) Figure 4O Ref # Part # Description A LDR-5304 Ladder/Eave Platform Handrail Bracket (2) B LDR-5305 Ladder/Eave Platform Kick Plate Splice Plate C Attach ladder/eave platform handrail bracket (LDR-5304) and ladder/eave platform kick plate splice plate (LDR-5305) to handrail post using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). 30 PNEG '-135' X Series Ladder, Cage and Platform

31 4. Assembly Instructions 72'-135' Ladder Only Eave Platform Package with Manway Guard (Continued) NOTE: The parts pointed out on this page are listed on Page 32. Figure 4P PNEG '-135' X Series Ladder, Cage and Platform 31

32 4. Assembly Instructions 72'-135' Ladder Only Eave Platform Package with Manway Guard (Continued) Ref # Part # Description A STX-0038 Platform Handrail Short B STX-0212 Middle Handrail Support Post C STX-0045 Stair to Roof Panel Angle Attach (2) D LDR-5302 Sidedraw Platform Handrail Short E STX-0043 Manway Incline Rail (2) F STX-0044 Manway Corner Post (2) G LDR-4088 Small Intermediate Handrail (4). Field cut to fit. H STX-0057 Manway Handrail Grab Bar (2). Attach using bin bolt and flange nut. I STX-0215 Roof Stair Toe Plate J LDR-4087 Large Intermediate Handrail (4). Field cut to fit. K L M N O Manway Attach intermediate handrails using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Place self-drilling screw at overlap. Attach all upper handrails using 5/16" x 2" bolt (S-7877) and 5/16"-18 flange nut (S-10268). Attach post and bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). P STX /4" - Platform Handrail Short Q LDR /8" - Sidedraw Platform Handrail Short R STX /4" - Manway Incline Rail 32 PNEG '-135' X Series Ladder, Cage and Platform

33 42'-60' Ladder Eave Platform Assembly Instructions PNEG '-135' X Series Ladder, Cage and Platform 33

34 4. Assembly Instructions 42'-60' Ladder Eave Platform Assembly Ladder Eave Platform Package 1. Figure 4Q below and Figure 4R on Page 35 shows the assembly of the platform supports. Use 5/16" hardware at all the connection points. (Platform floor will have to be attached at the same time as support angles.) NOTE: When installing the top wind ring, do NOT use the top set of holes in the stiffener. NOTE: Leave all hardware loose until completely assembled. 2. Left platform bracket must be line up with stiffener roof rib and rafter of beam if present in roof. Figure 4Q Ref # Part # Description A STX-0009 X Series Platform Bracket - Left B STX-0082 X Series Platform Bracket - Right C STX-0135 X Series Long Eave Platform Bracket D E Platform brackets mount inside of the stiffeners. 48' Shell 34 PNEG '-135' X Series Ladder, Cage and Platform

35 4. Assembly Instructions Ladder Eave Platform Package (Continued) Figure 4R Ref # Part # Description A STX-0134 Single Piece Long Eave Platform Floor B STX-0140 X Series Eave Platform Floor - Right C STX-0142 X Series Eave Platform Toe Board D STX-0143 X Series Long Eave Platform Splice Angle E STX-0138 X Series Eave Platform Middle Angle (2) F STX-0136 X Series Eave Platform Long Angle (2) G STX-0011 Platform Short Angle (2) H STX-0137 X Series Long Eave Platform Short Angle (2) I Use 5/16"-18 x 3/4" truss bolt (S-10267) and 5/16"-18 flange nut (S-10268) to attach platform floor and all substructure. PNEG '-135' X Series Ladder, Cage and Platform 35

36 4. Assembly Instructions Platform and Safety Cage Bar 3. Figure 4S shows the assembly of the platform post. This must all be assembled at the same time using 5/16" hardware. NOTE: 24" Safety cage bars are mounted to the inside of the post and the outside of the platform long angle. Figure 4S Ref # Part # Description A STX-0139 X Series Eave Platform Outside Corner Post (2) B STX-0144 X Series Eave Platform Inside Corner Post (2) C STX-0146 X Series Eave Platform Inside Center Post D STX-0141 X Series Eave Platform Outside Center Post E LDR " Safety Cage Bar (4) F Attach all handrail posts to platform using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). 36 PNEG '-135' X Series Ladder, Cage and Platform

37 Platform and Handrail Package 4. Assembly Instructions 4. Figure 4T shows the assembly of the platform handrails. These must also be attached using 5/16" hardware. NOTE: The parts pointed out on this page are listed on Page 38. Figure 4T PNEG '-135' X Series Ladder, Cage and Platform 37

38 4. Assembly Instructions Platform and Handrail Package (Continued) Ref # Part # Description A LDR-4088 Small Intermediate Handrail (2). Field cut to fit. B LDR-4087 Large Intermediate Handrail (2). Field cut to fit. C STX-0147 X Series Eave Platform Inside Top Rail (2) D STX-0251 X Series Eave Platform Left Front Post Brace E STX-0038 Platform Handrail Short F STX-0145 X Series Eave Platform Top Rail - Long (2) G STX-0252 X Series Eave Platform Front Right Post Brace H STX-0253 X Series Eave Platform Back Right Post Brace (N/S) I STX-0151 X Series Eave Platform Center Post Brace J K Attach upper handrails to platform posts using 5/16" x 2" bolt (S-7877) and 5/16"-18 flange nut (S-10268). Attach intermediate handrails to platform posts using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). L STX /4" - X Series Eave Platform Inside Top Rail M STX " - X Series Eave Platform Top Rail - Long N STX /4" - Platform Handrail Short 38 PNEG '-135' X Series Ladder, Cage and Platform

39 4. Assembly Instructions Platform and Swing Gate Package 5. Attach the platform gate bracket to the gate before attaching it to the inside platform post using 5/16" hardware. (See Figure 4U.) Figure 4U Ref # Part # Description A LDR-5218 Ladder Safety Gate B STX-0139 X Series Eave Platform Outside Corner Post C LDR-5185 Intermediate Platform Gate Bracket D Attach safety gate to platform post using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). PNEG '-135' X Series Ladder, Cage and Platform 39

40 4. Assembly Instructions Platform Ladder Bracket Package 6. Attach the wall angle to the sidewall sheet using the hole 9-3/8" from the stiffener hole pattern with 3/8" hardware. Assemble the wall bracket to the wall angle with 3/8" hardware and tighten. (See Figure 4V below and Figure 4W on Page 41.) Attach left and right intermediate platform ladder bracket to the wall bracket and platform support with 5/16" hardware. NOTE: Do not force the wall bracket in or out. Assemble the ladder and ladder brackets to the wall bracket using 5/16" hardware. The top ladder rung must be level with the platform floor. Figure 4V Ref # Part # Description A LDR-5178 Intermediate Platform Ladder Bracket - Left B LDR-5177 Intermediate Platform Ladder Bracket - Right C LDR-5174 Intermediate Platform Bracket - Left D E F G 9-3/8" Attach ladder sidewall angle (LDR-5168) to bin wall here 9-3/8" from platform wall bracket. Use 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach intermediate platform ladder to platform wall bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach ladder sidewall angle (LDR-5168) to platform wall bracket using 3/8-16" x 1" flange bolt (S-7485) and 3/8"-16 flange nut (S-9426). 40 PNEG '-135' X Series Ladder, Cage and Platform

41 4. Assembly Instructions Platform Ladder Bracket Package (Continued) Figure 4W Ref # Part # Description A 4FOOTRF B LDR-5159 C D 4' Roll Formed Ladder. Attach 4' roll formed ladder to intermediate platform ladder bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Eave Platform Ladder Bracket. Two (2) parts bolted back to back. Length of bolted parts dependent on bin diameter. Attach ladder stand off to wall bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach ladder stand off to platform bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). PNEG '-135' X Series Ladder, Cage and Platform 41

42 4. Assembly Instructions Platform and Safety Cage Package 7. Attach the ladder flare to the ladder using 5/16" hardware. You must drill the bottom hole through the ladder and use 5/16" hardware. (See Figure 4X.) 8. Attach the cage hoops and cage splice brackets to the ladder flares and platform posts. This must all be assembled at the same time using 5/16" hardware. NOTE: Be sure the ladder flares are vertical and parallel to the platform posts by adjusting the splice brackets. The ladder will NOT be square to the platform due to the radius of the bin. The side closest to the bin wall will be closer to the platform. Figure 4X Ref # Part # Description A LDR-5218 Ladder Safety Gate B LDR-5167 Safety Cage Hoop Splice (2) C LDR-5164 Safety Cage Hoop - Standard (4) D LDR-5493 Formed Ladder Flare (2) E F G Attach safety cage hoop to formed flare using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach safety cage hoop splice to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). This hole must be drilled through ladder on right and left sides. 42 PNEG '-135' X Series Ladder, Cage and Platform

43 42'-60' Ladder Only Eave Platform Assembly Instructions PNEG '-135' X Series Ladder, Cage and Platform 43

44 4. Assembly Instructions 42'-60' Ladder Only Eave Platform Assembly NOTE: The parts pointed out on this page are listed on Page 45. Figure 4Y 44 PNEG '-135' X Series Ladder, Cage and Platform

45 4. Assembly Instructions 42'-60' Ladder Only Eave Platform Assembly (Continued) Ref # Part # Description A LDR-5318 Ladder Only 42'-60' Platform Top Handrail B LDR-5316 Ladder Only Eave Platform Middle Post C STX-0150 Manway Top Rail D STX-0043 Manway Incline Rail (2) E STX-0057 Manway Handrail Grab Bar (2). Attach using bin bolt and flange nut. F STX-0044 Manway Corner Post (2) G LDR-5317 Kick Plate Ladder Only Platform. Attach toes kick to ladder only handrail post and to platform inside center post. H STX-0045 Stair to Roof Panel Angle Attach (2) I LDR-4087 Large Intermediate Handrail (2). Field cut to fit. J LDR-4088 Small Intermediate Handrail (2). Field cut to fit. K L M N Attach upper handrails using 5/16" x 2" bolt (S-7877) and 5/16"-18 flange nut (S-10268). Attach intermediate handrails using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach post and bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Place self-drilling screw at overlap four (4) places. O STX /4" - Manway Top Rail P LDR " - Ladder Only 42'-60' Platform Top Handrail Q STX /2" - Manway Incline Rail PNEG '-135' X Series Ladder, Cage and Platform 45

46 NOTES 46 PNEG '-135' X Series Ladder, Cage and Platform

47 Ladder and Safety Cage Layout PNEG '-135' X Series Ladder, Cage and Platform 47

48 4. Assembly Instructions Ladder and Safety Cage Assembly Ladder and Safety Cage Layout Item 10 Rings 11 Rings 12 Rings 13 Rings 14 Rings 15 Rings 16 Rings 17 Rings 18 Rings 19 Rings 20 Rings 21 Rings 22 Rings 23 Rings 24 Rings 25 Rings 26 Rings 27 Rings 28 Rings 29 Rings 30 Rings 31 Rings 32 Rings 33 Rings 34 Rings 35 Rings 36 Rings 37 Rings 38 Rings 39 Rings 40 Rings A Platform Located above Ring: 4' Ladder Section Safety Cage 4' Section Bell Safety Cage - 2' Bell Safety Cage - 3' Bell Safety Cage - 4' Eave Platform Package Dimension A 327" 359" 167" 231" 231" 231" 263" 295" 295" 295" 327" 327" 359" 231" 263" 295" 327" 359" 327" 327" 327" 327" 327" 359" 231" 231" 263" 295" 327" 327" 327" B Platform Located below Ring: ' Ladder Section Safety Cage 4' Section Safety Cage 3' Section Bell Safety Cage - 2' Bell Safety Cage - 3' Bell Safety Cage - 4' Intermediate Platform Package Dimension B 224" 192" 224" 256" 256" 256" 288" 320" 320" 352" 352" 256" 256" 256" 256" 256" 256" 256" 320" 320" 352" 352" 224" 256" 256" 256" 256" 256" 320" C Platform Located below Ring: ' Ladder Section Safety Cage 4' Section Safety Cage 3' Section Bell Safety Cage - 2' Bell Safety Cage - 3' Intermediate Platform Package Dimension C 256" 256" 256" 256" 256" 320" 352" 320" 352" 352" 352" 320" 320" 320" 320" 320" 352" 320" D Platform Located below Ring: ' Ladder Section Safety Cage 4' Section Bell Safety Cage - 3' Intermediate Platform Package NOTE: See Pages 49 and 50 for A, B, C and D layouts. Dimension D 320" 320" 320" 320" 320" 320" 320" 48 PNEG '-135' X Series Ladder, Cage and Platform

49 2.66" Commercial Ladder Offset and Platform Layout 4. Assembly Instructions A A B A Rings Rings A B Figure 4Z PNEG '-135' X Series Ladder, Cage and Platform 49

50 4. Assembly Instructions A B C A A B C B D C Rings Rings A B C D Figure 4AA 50 PNEG '-135' X Series Ladder, Cage and Platform

51 Ladder and Safety Cage Assembly Instructions PNEG '-135' X Series Ladder, Cage and Platform 51

52 4. Assembly Instructions NOTE: See table on Page 48 for correct ladder and safety cage layout. 1. Assemble the wall bracket to the wall angle using 3/8" hardware. (See Figure 4AC on Page 53.) NOTE: The wall angle must be assembled on top of the previous wall angle to provide a flat surface to mount the wall bracket. 2. Assemble the wall braces to the wall bracket and the horizontal sidewall seam using 5/16" hardware. IMPORTANT: Use a hole in the horizontal seam and two (2) holes in the wall braces that allows the wall bracket to be aligned with the above wall bracket. If they are NOT aligned, the ladder will not be straight. 3. Attach the next ladder section to the upper section using the splice plates and 5/16" hardware. (See Figure 4AB.) Assemble the ladder standoff brackets to the ladder and wall bracket using the ladder standoff wedges and 5/16" hardware. (See Figure 4AC on Page 53.) Figure 4AB Ref # Part # Description A S Flange Bolt 5/16"-18 x 1" JS500 Grade 8 or Grade 8.2 Full Thread with Sealing Washer B S Flange Nut 5/16"-18 JS500 Grade 5 C LDR-4317 Ladder Section Splice Plate D 4FOOTRF 4' Roll Formed Ladder 52 PNEG '-135' X Series Ladder, Cage and Platform

53 4. Assembly Instructions Left Hand Side Ladder Assembly Figure 4AC Ref # Part # Description A LDR-5168 Ladder Sidewall Angles B 4FOOTRF 4' Roll Formed Ladder C LDR-5169 Ladder Sidewall Bracket D LDR-5197 Ladder Bracket Wall Brace (Two (2) bolted together.) E LDR-4198 Ladder Standoff Wedge (Two (2) per wall bracket.) F LDR-4314 Ladder Standoff (Two (2) per wall bracket.) G LDR-4317 Ladder Section Splice Plate H I Attach using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach ladder standoff to wedge using 5/16" x 1" carriage bolt (S-3550) and 5/16"-18 flange nut (S-10268). PNEG '-135' X Series Ladder, Cage and Platform 53

54 4. Assembly Instructions Right Hand Side Ladder Assembly Figure 4AD Ref # Part # Description A 4FOOTRF 4' Roll Formed Ladder B LDR-5197 Ladder Bracket Wall Brace (Two (2) bolted together.) C LDR-5169 Ladder Sidewall Bracket D LDR-4314 Ladder Standoff (Two (2) per wall bracket.) E LDR-4198 Ladder Standoff Wedge (Two (2) per wall bracket.) F LDR-4317 Ladder Section Splice Plate G LDR-5168 Ladder Sidewall Angles 54 PNEG '-135' X Series Ladder, Cage and Platform

55 4. Assembly Instructions 4. Assemble the safety cage rail spacer, standard safety cage hoops and cage bars to the ladder using 5/16" hardware. (See Figure 4AE.) 5. Assemble the safety cage rail spacer, bell safety cage hoops and cage bars to the ladder using 5/16" hardware. (See Figure 4AE.) Figure 4AE Ref # Part # Description A 4FOOTRF 4' Roll Formed Ladder B LDR-5469 Safety Cage Hoop Bell C LDR-5164 Safety Cage Hoop Standard D E Bell Cage Bar Safety Cage Bar (Seven (7) around per section.) NOTE: See table on Page 48 for correct size of cage bars. PNEG '-135' X Series Ladder, Cage and Platform 55

56 4. Assembly Instructions Figure 4AF 3' Ladder Safety Cage Section Ref # Part # Description A LDR-5162 Safety Cage Hoop Bracket B LDR-5164 Safety Cage Hoop Standard C LDR ' Safety Cage Bar D E Attach safety cage bar (LDR-5166) to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach LDR-5162 to LDR-5164 using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). 56 PNEG '-135' X Series Ladder, Cage and Platform

57 4. Assembly Instructions Figure 4AG 4' Ladder Safety Cage Section Ref # Part # Description A LDR-5162 Safety Cage Hoop Bracket B LDR-5164 Safety Cage Hoop Standard C LDR ' Safety Cage Bar D E Attach safety cage bar (LDR-5166) to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach LDR-5162 to LDR-5164 using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). PNEG '-135' X Series Ladder, Cage and Platform 57

58 4. Assembly Instructions Figure 4AH 2' Ladder Safety Bell Cage Ref # Part # Description A LDR-5469 Safety Cage Hoop Bell B LDR-5162 Safety Cage Hoop Bracket C LDR ' Safety Cage Bar (4) D LDR ' Safety Cage Bar for Full 31" Bell (3) E Attach safety cage hoop bracket to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). F Attach safety cage bar to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Figure 4AI 3' Ladder Safety Bell Cage Ref # Part # Description A LDR-5469 Safety Cage Hoop Bell B LDR-5162 Safety Cage Hoop Bracket C LDR ' Safety Cage Bar (4) D LDR ' Safety Cage Bar for Full 31" Bell (3) E Attach safety cage hoop bracket to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). F Attach safety cage bar to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). 58 PNEG '-135' X Series Ladder, Cage and Platform

59 4. Assembly Instructions Figure 4AJ 4' Ladder Safety Bell Cage Ref # Part # Description A LDR-5469 Safety Cage Hoop Bell B LDR-5162 Safety Cage Hoop Bracket C LDR ' Safety Cage Bar (4) D LDR ' Safety Cage Bar for Full 31" Bell (3) E F Attach safety cage hoop bracket to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach safety cage bar to safety cage hoop using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). PNEG '-135' X Series Ladder, Cage and Platform 59

60 4. Assembly Instructions 6. The last ladder section at each intermediate platform and at the bottom may need to be cut off for proper fit. (See Figure 4AK.) 7. Anchor the last ladder section to the intermediate platform using the ladder base and 5/16" hardware. You must drill the platform floor to attach the ladder base to the platform. (See Figure 4AK.) Figure 4AK Ref # Part # Description A 4FOOTRF 4' Roll Formed Ladder B LDR-5181 Intermediate Platform Ladder Base C D Attach ladder to ladder base using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Cut the ladder to fit the intermediate platform. 60 PNEG '-135' X Series Ladder, Cage and Platform

61 Ladder Intermediate Platform Package PNEG '-135' X Series Ladder, Cage and Platform 61

62 4. Assembly Instructions X Series Ladder Intermediate Platform Package Platform Package 1. Attach the wall angle to the sidewall sheet with 3/8" hardware. Assemble the left and right intermediate platform brackets to the wall angles with 3/8" hardware. (See Figure 4AL.) NOTE: Leave all hardware loose until completely assembled. Assemble the platform to the front and back angles and platform brackets using the 5/16" truss bolts. Using 5/16" hardware, assemble the posts. Figure 4AL Ref # Part # Description A LDR-5168 Ladder Sidewall Angle B LDR-5183 Intermediate Platform Back Post - Left C LDR-5172 Ladder Intermediate Platform D LDR-5184 Intermediate Platform Back Post - Right E LDR-5179 Intermediate Platform Front Post (2) F LDR-5180 Intermediate Platform Toe Board G STX-0138 X Series Eave Platform Middle Angle (2) H LDR-5175 Intermediate Platform Front Angle I LDR-5173 Intermediate Platform Bracket - Right J LDR-5174 Intermediate Platform Bracket - Left K Use 5/16"-18 x 3/4" truss bolt (S-10267) and 5/16"-18 flange nut (S-10268) to attach platform floor and all substructure. L Attach all handrail posts to platform using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). M Attach ladder sidewall angle to intermediate platform bracket using 3/8-16" x 1" flange bolt (S-7485) and 3/8"-16 flange nut (S-9426). 62 PNEG '-135' X Series Ladder, Cage and Platform

63 Platform Package (Continued) 4. Assembly Instructions 2. Assemble the platform wall brace to the intermediate platform front posts and wall angles with 5/16" hardware. (See Figure 4AM.) Attach the platform gate bracket to the gate before attaching it to the platform back post using 5/16" hardware. Assemble the top and intermediate handrails to the post using 5/16" hardware. NOTE: The parts pointed out on this page are listed on Page 64. Figure 4AM PNEG '-135' X Series Ladder, Cage and Platform 63

64 4. Assembly Instructions Platform Package (Continued) Ref # Part # Description A LDR-4088 Small Intermediate Handrail (2). Field cut to fit. B LDR-4087 Large Intermediate Handrail (2). Field cut to fit. C LDR-5185 Intermediate Platform Gate Bracket D LDR-5182 Intermediate Platform Top Handrail (2) E LDR-5168 Ladder Sidewall Angle F LDR-5218 Ladder Safety Gate G LDR-5206 Eave Platform Wall Brace H I J K L Attach intermediate platform door bracket to platform corner post using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach intermediate handrail to handrail post using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach upper handrails to platform post using 5/16" x 2" bolt (S-7877) and 5/16"-18 flange nut (S-10268). Attach safety gate assembly to intermediate platform door bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). Attach eave platform wall brace to ladder sidewall angle using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). M LDR " - Intermediate Platform Top Handrail 64 PNEG '-135' X Series Ladder, Cage and Platform

65 Platform and Safety Cage Bar Package 4. Assembly Instructions 3. Assemble the safety cage bars (knee brace) to the posts and front and back angles using 5/16" hardware. (See Figure 4AN.) NOTE: Be sure the intermediate platform is level before tightening hardware. Figure 4AN Ref # Part # Description A LDR " Safety Cage Bar (4) PNEG '-135' X Series Ladder, Cage and Platform 65

66 4. Assembly Instructions Platform and Ladder Cage Package 4. Assemble the ladder and ladder brackets to the intermediate platform bracket using 5/16" hardware. The top ladder rung must be level with the platform floor. (See Figure 4AO.) Figure 4AO Ref # Part # Description A 4FOOTRF 4' Roll Formed Ladder B LDR-5178 Intermediate Platform Ladder Bracket - Left C LDR-5177 Intermediate Platform Ladder Bracket - Right D Attach intermediate platform ladder bracket to platform wall bracket using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18 flange nut (S-10268). 66 PNEG '-135' X Series Ladder, Cage and Platform