Signature of Bidder with Seal 1 of 10 EPI

Transcription

1 1 Brickwork in cement mortar 1:6 (One of cement and six of sand) using ground moulded II class chamber burnt bricks of size 9" x 4 3/8" x 2 3/4" for super structure in the following floors including fixing the frames of doors and windows, scaffolding, proper setting curing etc, complete in all respects. a In Ground floor 150 Cum Rupees Three Thousand Nine Hundred b In First floor 150 Cum Rupees Four Thousand Forty Three Only c In Second floor 150 Cum Rupees Four Thousand Eighty Seven Only d In Third floor 150 Cum Rupees Four Thousand One Hundred Thirty One Only e In Fourth floor 150 Cum Rupees Four Thousand One Hundred Seventy Five Only f In Fifth floor 150 Cum Rupees Four Thousand Two Hundred Nineteen Only g In Sixth floor 150 Cum Rupees Four Thousand Two Hundred Sixty Three Only h In Seventh floor 150 Cum Rupees Four Thousand Three Hundred Seven Only I In Eighth floor 40 Cum Rupees Four Thousand Three Hundred Fifty One Only 2 Providing and laying the READY MIX CONCRETE of M 25 Grade using ordinary Portland cement with a 1650 Cum Rupees Four Thousand One Hundred Forty minimum cement content of 370 Kg/m3 with water cement ratio not exceeding 0.45 including the use of Five Only plastixer of approved make and dosage of required grade, laying in position at all locations and levels using 20mm size and downgraded ISS HBG aggregates in all types of works, cost of sand of approved quality including hire charges for pump and pumping charges to the required location, machine vibrating, pumping, curing, providing fixtures like fan clamps etc as specified, charges for conveyance of RMC from plant to the site or all as required excluding cost of reinforcement and fabrication charges, centering and shuttering, mix design details to get approved before commencement of the work adopting pour card system by the departmental officers etc., complete as per IS /1990 In All floors Plain cement concrete 1:3:6 (One of cement, three of sand and six of hard broken stone) using 20mm size hard broken granite broken stone for foundation including laying, shoring, strutting bailing out water, ramming, finishing, curing etc., complete as directed by thedepartmental officers. 17 Cum Rupees Three Thousand Two Hundred One Only Brick Partition wall 12cm thick in cement mortar 1:5 (one of cement and five of sand) using ground moulded II class chamber burnt bricks of size 9"x 4 3/8" x 2 3/4" including fixing the frames of doors and windows, scaffolding and proper setting, curing, finishing etc., complete as directed by the departmental officers a In Ground floor 400 Sqm Rupees Four Hundred Sixty Three Only Signature of Bidder with Seal 1 of 10 EPI

2 b In First floor 500 Sqm Rupees Four Hundred Seventy Two Only c In Second floor 500 Sqm Rupees Four Hundred Eighty One Only d In Third floor 500 Sqm Rupees Four Hundred Ninety Only e In Fourth floor 500 Sqm Rupees Four Hundred Ninety Nine Only f In Fifth floor 500 Sqm Rupees Five Hundred Seven Only g In Sixth floor 500 Sqm Rupees Five Hundred Sixteen Only h In Seventh floor 500 Sqm Rupees Five Hundred Twenty Five Only Providing form work for centering, shuttering etc., for all reinforced concrete work like lintels, window boxing etc., including shuttering, upto 3.00m high using MS sheet of size 90cm x 60cm and BG 10, stiffened with MS angle of size 25mm x 25mm x 3mm laid over silver oak (Country wood) joist of size 10 cm x 6.5 cm (spaced about 91cm centre to centre) distance and supported by casurina props of size 10cm to 13cm dia (spaced at 75cm centre to centre) and removing the same after a specified period without damaging RCC works in all floors etc complete as directed by the departmental officer. (Sunshade /Window/Boxing / column 6 Providing form work for centering, shuttering etc., for all reinforced concrete work like slab, beams, lintels, loft etc., including shuttering, upto 3.00m high using MS sheet of size 90cm x 60cm and BG 10, stiffened with MS angle of size 25mm x 25mm x 3mm laid over silver oak (Country wood) joists of size 10cm x 6.5 cm (Spaced about 91cm center to center) distance and supported by casurina props of size 10cm- 13cm dia (spaced at 75 cm center to center) and removing the same after a specified period without damaging RCC works in all floors etc., complete as directed by the departmental officer. (Slabs, Lintels & Lofts) 7 Supplying, fabricating and placing in position the following kinds of steel grills for reinforcement for all RCC works and other civil works etc., including the cost of steel, binding wire and fabrication of reinforcement grills etc., complete complying with relevant standard specification 4000 Sqm Rupees One Hundred Eighty Nine Only Sqm Rupees Two Hundred Fifty Seven Only Steel rods of all sizes 300 MT Rupees Forty Seven Thousand Five Hundred Seventy Two Only 8 Providing 7.5 cm thick staircase parapet wall using ground moulded II class chamber burnt bricks of size 7 Sqm Rupees Four Thousand Three Hundred "x4 3/8"x2" 3/4" in cement mortar 1:4 (One of cement and four of sand) and plastering the hand rails portion only with red oxide plastering in cement mortar 1:4 (one of cement and four of sand) 20 mm thick using 9.8kg of red oxide powder per 10M2 and plastering either side of parapet with CM 1:4 (One of cement and four of sand) 20mm thick providing skirting, finishing smooth complete in all respects in all floors Ninety Five Only 9 Plastering with CM 1:5 (One of cement and five of sand) 12mm thick including providing band cornice, Sqm Rupees One Hundred Two Only curing, finishing, etc., complete as directed by the departmental officers 10 Stucco plastering 12mm thick in cement mortar 1:3 (One of cement and three of chips) using hard blue granite chips of size 10mm and below over the existing plastered surface including proper finishing, curing, etc., complete as directed by the departmental officers. 300 Sqm Rupees One Hundred Thirty Three Only Signature of Bidder with Seal 2 of 10 EPI

3 11 Special ceiling plastering for all RCC works in cement mortar 1:3 (One of cement and three of sand) 10mm thick including hacking the RCC surface, providing necessary water band using the same mix of mortar wherever necessary proper finishing, curing, scaffolding etc., complete with relevant standard specification 12 Plastering with CM 1:4 (One of cement and four of sand) 20mm thick including providing band cornice, curing, finishing, etc., complete as directed by the departmental officers 13 Cement concrete 1:5:12.5 (One of cement, five of sand and twelve and half of broken brick jelly) using 20mm size broken brick jelly including laying, ramming, curing finishing, etc. complete as directed by the departmental officers 14 Supplying and fixing in position the terracotta jolly of approved size and quality having 8"x8" (20cmx20cmx8cm thick in cement mortar 1:3 (One of cement and three of sand) including cost of jolly proper laying necessary scaffolding wherever necessary curing of cement joints etc. complete as directed by the departmental officers. 15 Supplying and fixing doors with monolithic RCC door frames of size 100mm x 75mm with one edge groove of size 30mm x 20mm in reinforced CC 1:1.5:3 (One of cement, one and half of sand and three of hard broken jelly) including cost of steel and fabrication of reinforcement with 3 Nos. of 6mm MS rod alround and using 3mm steel as stirrups at 30cm centre to centre including fixing 3 Nos. of iron brackets of size 100mm x 100mm x 5mm as per drawing 6 Nos. of hold fasts of size 50mm x 165mm x 3mm aluminum sleeves as per drawing 2 Nos. of iron oxidized tower bolt receiver and 6 Nos. hold fast, check nuts as per drawing including moulding with steel mould precasting making the concrete surface smooth curing etc., and GI shutter with 20 gauge GI sheets folded inside required hat section as shown in the drawing, riveting one horizontal stiffener of size as per drawing at the middle of the shutter and two sets of diagonal stiffeners at the top and bottom panels as per drawing including supplying and fixing of 2 Nos. of iron oxidized aldrops of size 300 x 12mm, 2 Nos. of iron oxidized tower bolt 6000 Sqm Rupees One Hundred Fifty One Only Sqm Rupees One Hundred Thirty Four Only Cum Rupees Two Thousand Four Hundred Eighty Six Only Sqm Rupees Four Hundred Seventy Two Only Nos Rupees Two Thousand Nine Hundred Forty Only s of size 200 x 12mm including fixing them to the shutter by riveting or welding and drilling holes for locking arrangements in concrete frame including grinding, finishing smooth and painting one coat of premixed red oxide paint for the GI shutter etc., complete in all respects as directed by the departmental officers. Door size of 910mm x 1980mm (Dumpling type) Signature of Bidder with Seal 3 of 10 EPI

4 16 Fabricating, supplying and fixing in position the GI single shutter door of overall size 760mm x 1980mm using all structural steel sections confirming to IS 2062:1999, IS 277:2003 shuttering having thickness 0.80mm} shutter frame all round using Equal leg angles of size 25mm x 25mm x 3mm thick confirming to IS 808:1989, stiffeners 150mm width at top and bottom & 200mm width at centre at rear side, vertical grooves of size ~ 25mm width & ~ 15mm deep at an equal distance varying from ~ 65 to 85mm, machine pressed having minimum 7 grooves in a shutter, suitably welded the Door frame angle and GP sheet shutter door including supply and fixing of 3 Nos. of I.O. medium weight mild steel butt hinges 125mm x 65mm size with IS :1341 mark of MS hold fast 150mm x 25mm x 6mm size confirming of IS:1730 & IS : 2062:1999, 1 No. of I.O. mild steel sliding door bolts - aldrop with IS 281 mark of size 300mm x 16mm, placing the supporting plate of size ~ 330mm x 200mm for resting the alrop, plate using hot rolled and also provide MS flat of size ~ 330mm (length) x 50mm (breadth) x 3mm thick for sliding bolt portion & ~ 75m x ~ 50mm x 3mm thick for staple portion - placing over the HR sheet, 2 Nos. of I.O. tower bolt of size 200mm x 12mm with IS 204 mark, 2 Nos. of tower bolt receiver using 6mm (MS bars 180 Nos Rupees Two Thousand Eighty Eight Only only) ~ 75 to 85mm length bending to suitable shape & size and fixing into the door frame etc., welding using a suitable grinding for smooth finish, applying one coat of priming etc., complete as directed by the departmental officers. (Door overall size 760mm x 1980mm) (Dumping type) 17 Fabricating, supplying and fixing the GI Window of overall size 1220 x 1220mm using all structural steel sections confirming to "Steel for General Structural Purpose - IS 2062 : 1999" using Equal Leg angles (IS 808:1989) of size 35 x 35 x 5mm thick for window frames all round including providing 4 Nos. of hold fast 150mm long, providing11 Nos. of 10mm square steel bars (IS ~ 10mm centers (whereas ~ 125 to 135mm near handle portion for easy hand operation) making window shutter using Galvanised Plain Steel heet {IS 277: Plain sheet - T pe: Ordinary, Designation : GP, Grade 'O' GM / Sq.m - sheet thickness 0.63mm}, shutter frame all round using Equal Leg angles ( IS 808 :1989) of size 25 x 25 x 3mm thick, each window with three shutters, having vertical grooves of size ~ 25mm width & ~ 15mm deep at an equal distance varying from ~ 65 to 85mm, machine pressed, minimum 4 grooves in each shutter, providing Indian Standard Hot Rolled Steel Tee Bars - "T" section (IS 1173:1978) of size 25mm x 25mm x 3mm for central vertical post - 2 Nos. 180 Nos Rupees One Thousand Five Hundred Fifty Seven Only Signature of Bidder with Seal 4 of 10 EPI

5 suitably welded the window frame angle and GP sheet shutter door including supply & fixing 6 Nos. of I.O. medium weight mild steel butt hinges (with IS :1341 mark in hinges itself) of size 100mm (Length) x 58mm (Breadth), Supply & fixing of 3 Nos. of I.O. Heavy duty handle of over all size ~ 150 (length) x ~ 25mm at one end and gradually tapered to ~ 12mm (breadth) x ~ 2.50mm thick with hexagonal bolt of size ~ 20mm (length) x ~ 6mm thick with suitable nut having complete set - total minimum weighing not less than ~ 105gm / handle set, the handle to be rested on the back plate of size ~ 70mm (length) x ~ 30mm (breadth) bending / folding to the required shape & size using Hot rolled (HR) sheet {IS 1079: Grade 'O' - Ordinary quality - using sheet thickness ~ 1.60mm}, supply & fixing of 3 Nos. CP cabin hook of size ~ 150mm (length) x ~ 3.50 to 4.00mm thick of good quality having complete set including 2 holding clips - minimum weighing to not less than ~ 40gm / cabin hook set and to be fixed into the window shutter / frame (all fittings as suggested by the departmental officers) etc., welding using a suitable procedure, grinding for smooth finish, apply primer one coat to the exposed area by spraying using red oxide primer (classic / matt finish as directed by the field officers) of good quality etc., complete in all respects. (Dumping type shutter) (Window overall size 1220mm x 1220mm) 18 Fabricating, supplying and fixing the GI Window of overall size 910 x 1220mm using all structural steel sections confirming to "Steel of General Structural Purpose - IS 2062 : 1999" using Equal Leg angles of size 35mm x 35mm x 5mm thick confirming to IS 808:1989 for window frames all round including supplying and fixing 4 Nos. of hold fast ~ 150mm long, providing 11 Nos. of 10mm square steel bars (IS ~ 100mm centers (whereas ~ 125 to 135mm near handle portion for easy hand operation) shutter using Galvanised Plain Steel Sheet {IS 277: Plain sheet - Type : Ordinary, Designation : GP, Grade 'O' GM / Sq.m - sheet thickness 0.63mm}, shutter frame all round using Equal Leg angles ( IS 808 :1989) of size 25mm x 25mm x 3mm thick, each window with two shutters, having vertical grooves of size ~ 25mm width & ~ 15mm deep at an equal distance varying from ~ 65 to 85mm, machine pressed, minimum not less than 4 grooves in each shutter, providing Indian Standard Hot Rolled Steel Tee Bars - "T" section (IS 1173:1978) of size 25mm x 25mm x 3mm for central vertical post - 1 No. suitably 190 Nos Rupees One Thousand Five Hundred Fifty Seven Only Signature of Bidder with Seal 5 of 10 EPI

6 welded the window frame angle and GP sheet shutter door including supply & fixing 4 Nos. of I.O. medium weight mild steel butt hinges (with IS :1341) of size 100mm x 58mm, 2 Nos. of I.O. Heavy duty handle of over all size ~ 150 (length) x ~ 25mm with hexagonal bolt of size ~ 20mm (length) x ~ 6mm thick with suitable nut having complete set - minimum weighing to not less than ~ 105gm / each handle set, the handle to be rested on the back plate of size ~ 70mm (length) x ~ 30mm (breadth) bending / folding to the required shape & size using Hot rolled (HR) sheet {IS 1079: Grade 'O' - Ordinary quality - using sheet thickness ~ 1.60mm}, supply & fixing of 2 Nos. CP cabin hook of size ~ 150mm (length) x ~ 3.50 to 4.00mm thick of good quality having complete set including 2 holding clips - minimum weighing to not less than ~ 40gm / cabin hook set and to be fixed into the window shutter / frame welding using a suitable procedure, grinding for smooth finish, apply primer one coat to the exposed area by spraying using red oxide primer (classic / matt finish as directed by the field officers) of good quality etc., complete in all respects. (Window of overall size 910mm x 1220mm) 19 Supplying and fixing of factory made PVC rigid panel door with frame made from MS tubes of 19 gauge size of 19mm x 19mm and covered with heat moulded PVC channel of 5mm thick and width of 50mm to form styles and rails. The inner panel should be inserted between the frame with 5mm thick PVC rigid foam sheet welded/sealed to the styles and rails along with 5mmx25mm PVC beading on all and either sides. The vertical tube may be filled with suitable materials to further enhance the screw holding capacity etc., complete in all respects and colour as directed by the departmental officer. Door Size 0.76m x 1.98m 500 Sqm Rupees One Thousand Three Hundred Ten Only Supplying and fixing of Oriya type water closet 45cm with 'P' or 'S' trap (White glazed) earthern ware best (IN ALL FLOORS) including concrete packing fixing filling the sink portion with brick jelly lime concrete 32:12 1/2 (Thirty two parts of broken brick jelly and twelve and half of lime (no sand) using 20mm size broken brick jelly and plastering the top of flooring with cement mortor 1:4 (one of cement and four of sand) 12mm thick including plastering the sides of sink portion in cement mortor 1:3 One of cement and three of sand) 12mm thick mixed with water proofing compound 4 lbs/cft in cement applying one coat of britex solution including curing for the sides and bottom of the sink portion, curing etc., complete as directed by the departmental officers 21 Cement concrete 1:2:4 (One of cement, two of sand and four of hard broken stone), using 10mm gauge hard broken stone for all precast cement concrete slabs for cubboard planks, side slab for boxing around window and other similar works having 25mm thickness excluding cost and fabrication of reinforcement grills in position shuttering centering but including precasting curing finishing and fixing in position as directed by the departmental officers etc., complete complying with standard specification. (Average rate for all floors) 22 Supplying and fixing in position ferro cement corner slab of size 10 '' radius and 1 in thickness in bathroom including grooves in the wall placing in position and fixing with necessary cement mortar, finishing curing etc. all complete as directed by the deptl., officers 188 Nos Rupees Three Thousand One Hundred Thirty One Only Sqm Rupees Nine Hundred Two Only Sqm Rupees Forty Five Only Signature of Bidder with Seal 6 of 10 EPI

7 23 Providing Ellis Pattern flooring 20mm thick (Ellis pattern) with layer of cement concrete 1:3 (one of cement and three of hard broken stone) (No sand) using hard blue granite chips of size 3mm to 10mm and surface rendered smooth over RCC slab including supplying and fixing 20mm dia GI pipe outlet etc., complete in all respects. 24 Weathering course in concrete broken brick jelly 20mm size in pure slacked lime over RCC roof slab the proportion being 32:12 1/2 (Thirty two parts of broken brick jelly and twelve and half of slacked lime) laying to a thickness of 110mm and compacked and well beaten to 80mm by using wooden hand beater of weight not exceeding 2 kg hand beating sprinkling liberally with lime water and a small proportion of solution prepared by soaking kadukkai dry nut powder and jaggery (vellam) and giving required slope and thickness on roof etc. completed as directed by the departmental officers in the 8th floor terrace 25 Finishing the top of roof slab with one course of pressed tiles 23cm x 23cm x 2cm using cement mortar 1:3 (One of cement and three of sand) mixed with water proofing compound at 2% by weight of the cement and pointing with the same mortar, finishing, curing etc., complete as directed by the departmental officers in 8th floor 26 White washing two coats using clean shell lime including the cost of lime, gum, brushes and scaffolding etc., complete in all respects as directed by the departmental officers in all floors 27 Painting two coats of cement paint of approved quality over one coat of white cement paint primer including the cost of cement paint, brushes scaffolding curing etc. all complete as directed by the departmental officers 28 Painting the new iron work with one coat of first class synthetic enamel paint of approved quality and colour in addition over the existing primer coat including the cost of paint patty brushes and scaffolding etc. complete as directed by the departmental officers 29 Supplying and fixing of 110mm dia PVC pipe of 6kg/cm2 of approved quality confirming to IS 13592/1992 type B with ISI monogram packing the joints with hempyarn and cement including fixing into walls with necessary wooden plugs and holding down clamps, dismantling and making good of the dismantled portion with necessary connections to the sanitary fittings testing etc. complete in all respects 30 Supplying and fixing of 110mm dia PVC soil pipe of 6 kg/cm2 of approved quality confirming to IS 13592/1992 (type B) of finolex (or) equivalent with ISI monogram packing the joints with hempyarn and cement including fixing into walls in W/C room with necessary connection to the sanitary fittings, testing etc. complete in all respects in all floors as directed by the departmental officers 31 Supplying and fixing of 75mm dia PVC pipe of 6 kg/cm2 of approved quality confirming to IS 13592/1992 Type-B of finolex or equivalent with ISI monogram packing the joints with hempyarn and cement including fixing into walls with necessary wooden plugs and holding down clamps, dismantling and making good of the dismantled portion with necessary connection to the sanitary fittings and testing etc. complete in all respects in all floors as directed by the departmental officers 4000 Sqm Rupees Two Hundred Sixty Three Only Sqm Rupees Four Hundred Nineteen Only Sqm Rupees Four Hundred Nineteen Only Sqm 9.00 Rupees Nine Only Sqm Rupees One Hundred Six Only Sqm Rupees Fifty Four Only RM Rupees One Hundred Fifty Eight Only RM Rupees One Hundred Fifty Eight Only RM Rupees One Hundred Five Only Signature of Bidder with Seal 7 of 10 EPI

8 32 Supplying and fixing of 75mm dia PVC pipe of 6 kg/cm2 of approved quality confirming to IS 13592/1992 (type B) of finolex or equivalent with ISI monogram packing the joints with hempyarn and cement including fixing into walls with necessary connections to the sanitary fittings in bath/wc room, etc. complete in all respects in all floors as directed by the departmental officers from nahini trap to wall. 33 Supplying and fixing of 160mm dia PVC pipe of 6kg / cm2 of approved quality confirming to IS 13592/1992 (type B) of finolex or equivalent with ISI monogram under basement including packing the joints with hempyarn and cement with necessary wooden plugs and holding down clamps including fixing dismantling and making good of the dismantled portion with necessary connection to the sanitary fittings and testing etc. complete in all respects in Ground floor as directed by the departmental officers 500 RM Rupees One Hundred Five Only RM Rupees One Hundred Eighty Four Only Supplying and fixing of 110mm dia PVC rain water down fall pipe 4kg/cm2 confirming to IS with 1 No. of 260 RM Rupees One Hundred Thirty Two Only PVC bend/elbow and 1 No. of shoe with necessary clamps couplers gratings, teak wood plug etc. complete including fixing in proper position with solvent cement, making holes in the walls good of the dismantled portion with necessary brick work in CM etc. in all respects as directed by the departmental officers. 35 Supplying of following kinds of PVC pipe specials of approved quality suitable to pipe as per table II IS 14375/1999 a 110mm dia PVC vent cowl 12 Nos Rupees One Hundred Five Only b 110mmdia PVC single bend with door 168 Nos Rupees One Hundred Five Only c 110mm dia PVC double `Y' with door 84 Nos Rupees One Hundred Five Only d 110mm dia PVC single bend without door 12 Nos Rupees One Hundred Five Only e 75mm dia PVC bend with door 168 Nos Rupees Seventy Nine Only f 75mm dia PVC single `Y' with door 168 Nos Rupees Seventy Nine Only g 75mm dia PVC vent cowl 24 Nos Rupees Seventy Nine Only h 75mm dia PVC single bend without door 24 Nos Rupees Seventy Nine Only I 100x75mm dia Nahini trap with PVC grating 186 Nos Rupees Seventy Nine Only Supplying the following dia PVC pipes of pressure class at 10 kg/cm2 of approved quality having inner dia confirming to IS 13592/1992 as follows at the site of work a 40mm dia PVC pipe 45 RM Rupees Seventy Nine Only b 20mm dia PVC pipe 5000 RM Rupees Sixty Eight Only Supplying the following PVC specials of approved quality having inner dia confirming to IS 14735:1999 as follows at site of work a 20mm dia PVC Coupler 1000 Nos Rupees Fifty Three Only b 20mm dia PVC elbow 1000 Nos Rupees Fifty Three Only c 20mm dia PVC Tee 800 Nos Rupees Fifty Three Only d 20mm dia PVC nipple with check nut with washer 500 Nos Rupees Fifty Three Only e 20mm dia PVC FTA 500 Nos Rupees Fifty Three Only f 20mm x 15mm dia PVC reducer 350 Nos Rupees Fifty Three Only g 15mm dia PVC tap 350 Nos Rupees Two Hundred Sixty Three Only Signature of Bidder with Seal 8 of 10 EPI

9 h 40mm dia PVC tee 20 Nos Rupees Fifty Three Only i 40mm dia PVC bend 40 Nos Rupees Fifty Three Only j 40mm dia PVC threaded hex nipple 150 Nos Rupees Fifty Three Only k 40mm dia PVC FTA 150 Nos Rupees Fifty Three Only Labour charges for cutting and threading and laying and jointing of PVC pipes with necessary specials of following outer dia above ground level etc. (specification as per relevant standards of M.S.) a 20mm dia PVC pipe 5000 RM Rupees Eleven Only b 40mm dia PVC pipe 45 RM Rupees Sixteen Only Construction of inspection chamber 0.60M x 0.60 M for the following depth using 23cm thick ground moulded II class chamber burnt brick masonry walls in CM 1:5 (One of cement and five of sand) and inside plastering with 1:3 (One of cement and three of sand) 12mm thick including channeling benching etc. and top covered with SFRC over slab with frame (medium duty) and fixing in position etc. complete in all respects and as directed by the departmental officers (without foundation) a 0.90M depth (Average) 10 Nos Rupees Two Thousand Six Hundred Nineteen Only 40 Construction of Inspection chamber 0.60M x 0.60M for the following depth brick jelly cement concrete 1:5:12 1/2 (One of cement and five of sand and twelve and half of broken brick jelly) using 40mm size brick jelly 15cm thick for foundation 23cm thick brick masonry wall in CM 1:5 (One of cement and five of sand) using ground moulded II class chamber burnt bricks and inside plastering with 1:3 (one of cement and three of sand) 12mm thick including channeling, benching etc. and top covered with SFRC (medium duty) cover slab and fixing in position and necessary earth work excavation, refilling the sides of foundation in all soils except hard rock requiring blasting etc. complete in all respects as directed by the departmental officers a 0.90M depth (Average) 10 Nos Rupees Two Thousand Six Hundred Nineteen Only 41 Supplying and laying 300mm dia NP3 S & S type RCC pipe 2.50m long 40mm wall thickness as per IS 72 RM Rupees Two Hundred Sixty Three Only /2003 including cost of materials transportation charges including loading, unloading and stacking, laying in proper position and packing the jointing and gap with necessary brick work and plastering etc., complete as directed by the departmental officers 42 Brick partition walls 7.5cm thick using ground moulded II class chamber burnt bricks of size 9" x 4 3/8" x 2 3/4" in cement mortar 1:5 (One of cement and five of sand) in the following floors including scaffolding, proper setting, curing etc., complete in all respects a In Ground floor 40 Sqm Rupees Four Hundred Sixty Three Only b In First floor 50 Sqm Rupees Four Hundred Seventy Two Only c In Second floor 50 Sqm Rupees Four Hundred Eighty One Only Signature of Bidder with Seal 9 of 10 EPI

10 d In Third floor 50 Sqm Rupees Four Hundred Ninety Only e In Fourth floor 50 Sqm Rupees Four Hundred Ninety Nine Only f In Fifth floor 50 Sqm Rupees Five Hundred Seven Only g In Sixth floor 50 Sqm Rupees Five Hundred Sixteen Only h In Seventh floor 50 Sqm Rupees Five Hundred Twenty Five Only Supplying and fixing MS grill of approved design & quality including providing one coat of primer with approved priming etc., complete as directed by the department officers in all floors 1650 KG Rupees Forty Four Only Signature of Bidder with Seal 10 of 10 EPI