NATIONAL FERTILIZERS LIMITED - NOIDA Schedule of Quantities & Rates

Transcription

1 1 Sub: Face lifting and landscaping of NFL Office Building at, C.O., Noida TENDER ISSUED TO : M/s REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy EARTH WORK NATIONAL FERTILIZERS LIMITED - NOIDA Schedule of Quantities & Rates E/W in excavation by machanical means (hydruolic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and remaining of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50m All kinds of soil Cum Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. Cum Diluting and injecting chemical emulsion for POST CONSTRUCTIONAL antitermite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical 2.25 litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration Rmt SUB HEAD - I ( EARTH WORK)

2 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy CEMENT CONCRETE WORK 4 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. 5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : Sqm a 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) Cum Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). Sqm Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer s specification. Per 50 Kg Cement Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. Sqm SUB HEAD - 2 (CEMENT CONCRETE WORK) 3. REINFORCED CEMENT CONCRETE WORK 9 Centering and shuttering including strutting, propping etc. and removal of form work for : a Foundations, footings, bases and foundations for shed columns Sqm 52.85

3 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy.2018 Item b Suspended floors, roofs, landings, balconies and access platform. Sqm c Shelves cast in situe Sqm 2.86 d Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm e Columns, piers, abutments, pillars, posts and struts. Sqm 40.80

4 10 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy.2018 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii): 3 graded stone aggregate 20 mm nominal size). a All works upto plinth level Cum Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) : 3 graded stone aggregate 20 mm nominal size). b All works above plinth level upto floor V level Cum Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) : 3 graded stone aggregate 20 mm nominal size). b All works above plinth level upto floor V level Cum Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto Plinth/above plinth level. a Thermomechanically Treated Reinforcement TMT upto PL Kg b Thermomechanically Treated Reinforcement TMT above PL Kg

5 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy.2018 Item SUB HEAD - 3 (REINFORCED CEMENT CONCRETE WORK) 4. BRICK WORK 14 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) Cum Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) Cum Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) Sqm Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. Sqm 9.59 SUB HEAD - 4 (BRICK WORK)

6 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy STEEL WORK 18 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. a In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Kg Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. a In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Kg Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Kg SUB HEAD - 5 (STEEL WORK)

7 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy FLOORING WORK 21 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : a 25 mm thick Sqm Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. Sqm Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete Sqm 21.00

8 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design, fixing in approved design. The glass mosaic tiles shall be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. All completed as per direction of Engineer-incharge. Sqm Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. Sqm SUB HEAD - 6 (FLOORING WORK)

9 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy ROOFING & FALSE CEILING 26 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : a In 75x75 mm deep chase Metre Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. each Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. a 110mm diametre Metre Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe each 4.00 SUB HEAD - 7 ROOFING & FALSE CEILING 8. FINISHING WORKS

10 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy.2018 Item 30 P/L 12mm cement plaster of mix 1:4 ( 1 cement : 4 Fine sand ). Sqm mm cement plaster on the rough side of single or half brick wall of mix : a 1:6 (1 cement: 6 fine sand) Sqm mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) Sqm Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. sqm Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : a Water thinnable cement primer sqm Finishing walls with textured exterior paint of required shade : a New work (Two or more coats 3.28 ltr/10 sqm) over and including priming coat of exterior primer 2.20kg/10 sqm) sqm Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: a Two or more coats on new work sqm Decorative Printed tiles for Façade. Sqm Providing and fixing Stainless steel letters of grade 304 complete fixed at any height complete SUB HEAD - 8 (FINISHING WORKS) per CM height DISMENTLING

11 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. a Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) Cum b Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) Cum Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. Cum Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work. 41 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. kg In cement mortar Cum Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : a Of area 3 sq. metres and below Each 2.00 b Of area beyond 3 sq. metres Each Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. Kg 41.40

12 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. a For thickness of tiles 10 mm to 25 mm sqm 3.00 b For thickness of tiles above 25 mm and up to 40 mm sqm Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. 45 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 46 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. sqm 7.20 sqm Cum SUB HEAD - 9 (DISMENTLING WORK) 10. ALUMINIUM WORK 47 Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fastners of required dia and size, including necessary filling up the gaps at junctions, i.e. at the top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing paneling and dash fasteners to be paid for separately) : a For fixed portion

13 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy.2018 Powder coated aluminium (minimum thickness of powder coating 50 micron) kg For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required. (fittings shall be paid separately) b Powder coated aluminium (minimum thickness of powder coating 50 micron) kg Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side sqm Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer in charge. (Cost of aluminium snap beading shall be paid in basic item): a With float glass panes of 5.50 mm thickness Sqm 2.16

14 50 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy.2018 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the b With stainless steel cover plate minimum 1.25 mm Each Providing and fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick & 15 mm dia, at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer in charge. Powder coated aluminium sheet 2.5mm thick (minimum thickness of powder coating 50 micron) Kg SUB HEAD - 10 (ALUMINIUM WORK) 11. WATER PROOFING

15 52 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy.2018 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above a With average thickness of 120 mm and minimum thickness at khurra as 65 mm sqm SUB HEAD (WATER PROOFING) 12. SANITARY INSTALLATION

16 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests each 1.00 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, 54 including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors a W.C. pan with ISI marked white solid plastic seat and lid each Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : (Hindware/Camry or Equivalent) a Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern Each Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: (Hindware/Camry or Equivalent) a White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap Each Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

17 a REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy.2018 Semi rigid pipe b 32 mm dia Each Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : a Rectangular shape 453x357 mm Each 1.00 b Providing and fixing soil, waste and vent pipes : mm dia -Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 Metre Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter a 100 mm dia pipe Each Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : a For 100 mm dia pipe Each Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. a 100 mm dia -Sand cast iron S&S as per IS Each Providing and fixing heel rest sanitary bend

18 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy mm dia -Sand cast iron S&S as per IS Each Providing and fixing terminal guard 100 mm dia -Sand cast iron S&S as per IS Each Providing and fixing Collar 100 mm dia -Sand cast iron S&S as per IS Each Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : a 100 mm inlet and 100 mm outlet -Sand cast iron S&S as per IS Each Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) fof a 100 mm diameter pipe Metre Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and Each mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 69 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms each Each 2.00 SUB HEAD - 12 (SANITARY INSTALLATION ) 13. WATERSUPPLY

19 70 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy.2018 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. a 15 mm nominal outer dia Pipes Metre b 20 mm nominal outer dia Pipes Metre c 25mm nominal outer dia Pipes Metre SUB HEAD - 13 (WATER SUPPLY) 14. ROAD WORK Providing and laying 60mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern Sqm over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). Cum 75.01

20 REF. : NIT :NFL/CO/Tech/C/FL LS /2017 dated xx.yy Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator, vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). Cum Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer in Charge. With granite stone of area less than 0.50 sqm. Sqm SUB HEAD - 14 (ROAD WORK) Total Amount (Sub Head 1 to 14) Rs