6x5. Assembly Manual CAUTION. Sharp Edges PATENTS ARE PENDING. Building Dimensions. Approximate Size. Storage Area. Interior Dimensions

Size: px
Start display at page:

Download "6x5. Assembly Manual CAUTION. Sharp Edges PATENTS ARE PENDING. Building Dimensions. Approximate Size. Storage Area. Interior Dimensions"

Transcription

1 Assembly Manual 6x5 PATENTS ARE PENDING Building Dimensions Approximate Size Storage Area Exterior Dimensions Interior Dimensions Roof Edge to Roof Edge Wall to Wall Sq. Ft. Cu. Ft. Width Depth Height Width Depth Height 6 x m x.5 m.30 m 3.97 m cm cm 8.88 cm cm 37.6 cm cm

2 . Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner s manual.. Follow all directions and dimensions carefully. 3. Follow the step sequence carefully for correct results. 4. Be sure all the parts fit together properly before proceeding. 5. SAFETY FIRST: Care must be taken when handling various pieces of your kit since some contain sharp edges. Wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building. 6. GROUND MUST BE LEVEL: Be sure Floor Frames lie flat on ground. To prepare earth bed, remove sod and other debris. Level the high spots with flat shovel and tamp the bed down. Refer to Page 4 for Parts List. Before You Begin Site Preparation Foundation Recommendations Local building codes vary by region, refer to your local codes for specifications. Concrete Slab. Select level site for building.. Remove 6 of soil for slab. 3. Compact 4 gravel in hole. 4. Place 6 ml plastic over gravel. Wood Platform. Construct with x 4 treated lumber and 5/8 minimum exterior grade plywood using galvanized nails.. Level platform. No. Phillips Screwdriver Shovel BASIC TOOLS Pliers Rubber Mallet Level Tape Measure Work Gloves 5. Construct x 4 form. 6 Centers 6. Pour concrete and level. Slab Dimensions 56 / (43,5cm) Door Opening 56 / (43,5cm) Door Opening 68 / (74cm) 68 / (74cm)

3 Care & Maintenance Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch up scratches as soon as you notice them on your building. Immediately clean the area with a wire brush; wash it and apply touch up paint per manufacturer s recommendation. Roof: Keep roof clean of leaves and snow with long handled, soft bristled broom. Heavy amounts of snow on roof can damage the building making it unsafe to enter. Doors: Keep doors closed to prevent wind damage. Fasteners: Regularly check you building for loose screws, bolts, nuts, etc. and retighten them as necessary. Moisture: With changing temperatures, condensation will accumulate inside the building. Other Tips: A noncorrosive caulking is helpful to seal the building. Do Not store swimming pool chemicals in your building. Combustibles and corrosives must be stored in air tight containers.

4 Step Pre-Assembly Side Walls A Wall Panel Corner Panel ASSEMBLY COMMON FOR ALL PANELS MAKE TWO () SIDE WALL SECTIONS 4 Panels & Corner - Each ARROW TO TOP IMPORTANT MUST USE FLAT SOLID SURFACE DO NOT SNAP ON GROUND OR GRASS! B C Raise Panel at Angle NOTE: ALWAYS COVER THE ARROW! Overlap Panels and align ends Hook edge of top Panel to bottom Panel

5 Pre-Assembly Side Walls....cont D Bring Top Panel down flat while maintaining pressure in the middle to keep edge hooked E Apply pressure in area shown IMPORTANT MUST USE FLAT SOLID SURFACE DO NOT SNAP ON GROUND OR GRASS! Start in middle of assembly to snap panels together F Push down to snap Panels together working from the center outward in both directions G Push down to snap end of panels together 4

6 5 Pre-Assembly Side Walls.... cont H Install Corner Panel Cover Arrow on Corner Panel ARROW TO TOP Use edge of surface to allow Corner Panel to hang down 3 Push down to snap Panels together working from the center in each direction

7 Pre-Assembly Side Walls.... cont I Attach Upper Channel (painted) ARROW TO TOP 06 Upper Channel (painted) -IMPORTANT- START ASSEMBLY AT CORNER PANEL Corner must be against Channel 45 cut on Channel Corner Panel Upper Channel (painted) J Align Channel to Panel Ribs and pop into place at corner K Continue aligning Channel and popping into place 6

8 7 Pre-Assembly Side Walls....cont 055 Floor Channel (unpainted) 080 Corner Clip 4 M Insert Corner Clip M Insert Corner Clip L Attach Floor Channel in the same sequence as Upper Channel. Floor Channel is Unpainted -IMPORTANT- START ASSEMBLY AT CORNER PANEL Corner must be against 45 cut on Channel Channel Corner Panel MAKE TWO () SIDE WALL SECTIONS

9 Step Pre-Assembly Rear Wall A MAKE ONE () REAR WALL SECTION 5 Panels and Corner 0307 Wall Panel Corner Panel ARROW TO TOP IMPORTANT MUST USE FLAT SOLID SURFACE DO NOT SNAP ON GROUND OR GRASS! B ARROW TO TOP Install Corner Panel 8

10 9 Pre-Assembly Rear Wall....cont C Attach Upper Channel (Painted) 06 Upper Channel (painted) 056 Floor Channel (unpainted) 080 Corner Clip D Insert Corner Clip -IMPORTANT- START ASSEMBLY AT CORNER PANEL -IMPORTANT- START ASSEMBLY AT CORNER PANEL Corner must be against 45 cut on Channel Corner must be against 45 cut on Channel Channel Channel Corner Panel Corner Panel D Insert Corner Clip E Attach Floor Channel (unpainted) in the same sequence as Upper Channel.

11 Step 3 Pre-Assembly Front Wall A Assemble Door Jambs to Wall Panels Install Bolt, Washer & Nut in each Door Jamb 036 Wall Panel -Right 037 Wall Panel - Left 0373 Door Jamb 068 Corner Panel Door Jambs always on top of Panel ARROW TO TOP B Install Corner Panel Wall Panel on top of Corner Panel 0

12 Pre-Assembly Front Wall....cont C Attach Upper Channel (Painted) 06 Upper Channel 063 Header Trim 056 Floor Channel 080 Corner Clip 8 -IMPORTANT- START ASSEMBLY AT CORNER Corner must be against 45 cut on Channel Channel F Insert Corner Clip Corner Panel D Attach Header Trim (Painted) -IMPORTANT- START ASSEMBLY AT CORNER Corner must be against 45 cut on Channel Channel Corner Panel F E Attach Floor Channel (Unpainted) Insert Corner Clip

13 Step 4 Wall Assembly Side Wall Assembly Rear Wall Assembly CORNER PANEL ON TOP OF WALL PANEL Corner Clip Corner Panel Install Corner Clip Upper B Side Panel Install Corner Clip Lower A Make Sure Engaged 3 Make Sure Engaged 3

14 Wall Assembly....cont 3 Side Wall Assembly Front Wall Assembly Install Corner Clip Lower C D D D Make Sure Engaged 3 C CORNER PANEL ON TOP OF WALL PANEL Corner Clip Corner Panel C Install Corner Clip Upper D E Join Corner Side Panel Snap Corner Panels to Wall Panel Inside assembler applies pressure to hold wall firm INSIDE Outside assembler snaps corner panel to side panel top to bottom INSIDE C Make Sure Engaged 3

15 Step 5 Gable & Ridge Beam Assembly A 065 Left Gable 066 Right Gable 058 Header Angle 078 Gable Brace 8 4 Snap Gables onto Upper Channel Gable C B Install Gable Braces onto Gables Assemble Header Angle Upper Channel Header Angle Header Trim 4

16 5 Gable & Ridge Beam Assembly....cont 069 Ridge Beam 03 Ridge Beam Angle 6 4 D Assemble Ridge Beam Angle to Ridge Beam E Install Ridge Beam Assembly to Gables Frame Must Be Square

17 Step 6 Pre-assembly - Roof A MAKE TWO () ROOF SECTIONS Align Roof Panels and snap panel ribs together Roof Panel Roof Panel-Right 05 Roof Panel-Left 067 Roof Channel Roof Fascia 4 ARROW TO TOP HOLES HOLES B Assemble Roof Channel onto top and bottom NOTE Large Holes on Channels FACE DOWN C Assemble Fascia Trim onto each side

18 7 Step 7 Roof Assembly D Assemble Left Roof Section to building 070 Ridge Cap 0 NOTE HOLE POSITIONS E Install Ridge Cap on Right Roof Section

19 Roof Assembly....cont F Assemble Right Roof Section, Peak Caps, & Corner Caps Peak Cap Corner Cap Fold Peak Caps FOLD FOLD HELPFUL HINT Gray Paint FOLD Gently tap Channel to align holes with Main Ridge Beam G Install screws through Ridge Beam and Roof Angle into Roof Channel 8

20 9 Step 8 Door Assembly A Slide Clips onto Verticle Door Brace 036 Vertical Door Brace 0369 Vertical Door Brace Handle Padlock Eyelet Clip 4 4 Installing Clips INCORRECT! CORRECT! 036 B Attach Door Handle & Padlock Eyelet to Vertical Door Brace 0369

21 Door Assembly....cont C Align Door Panels & snap Panel Ribs together 076 Door Panel (/) 0308 Door Panel 0309 Door Panel 075 Door Brace (Horz) 4 HOLES ARROW TO TOP Hole to top D Attach Horizontal Door Braces HOLES 036 E Attach Vertical Door Braces

22 Door Assembly.... cont 088 Diagonal Door Brace 4 F Turn Door OVER G Attach Diagonal Braces & install Screws for Horizontal Braces H Turn Door OVER I Install Screws for Diagonal Braces

23 Door Assembly....cont Padlock Eyelet 6678 Hinge 064 Ramp 6 K Hang Door L J Install Door Hinges & Padlock Eyelet Anchor Building (See Step 9) M Install Ramp

24 3 Step 9 Anchor Building It is important that building be anchored after construction. These are recommended ways of anchoring. Anchor Kit Model No AK00, SAK00 or Recommended for use with concrete foundation. Contains corner gussets, perimeter clips, hardware, /4 masonry drill bit and installation instructions. 3 (33.0 cm) Anchor Kit Model No AK4, SAK4 or 6098 Recommended for use with any suggested base. Contains 4 Anchors with Cable, clamps and installation instructions. Anchor into Wood or Concrete For wood platform. Use Decking Screws. For concrete slab. Use Lag Screws. Insert Cable Feed Cable through hole in Ridge Beam & Ridge Beam Angle Turn Anchors into ground close to building and attach Cable.

25 Parts List 6x5 Dia. No. Part Name Qty Part No. Dia. No. Part Name Qty Part No. Wall Panel Wall Panel - Right Wall Panel - Left Corner Panel Upper Channel (painted) 06 6 Floor Channel (unpainted) Upper Channel (painted) 06 8 Floor Channel (unpainted) Door Jamb Header Trim 063 Ramp 064 Corner Clip Left Gable Right Gable Header Angle Gable Braces Ridge Beam Ridge Beam Angle 03 9 Roof Panel Roof Panel (left) 05 Roof Panel (right) 050 Roof Channel Roof Fascia Ridge Cap Peak Cap 6 Corner Cap 4 7 Door Panel (/) Door Panel Door Panel Vertical Door Brace Vertical Door Brace Horizontal Door Brace Diagonal Door Brace 088 Separate contents of the carton by the part number while reviewing parts list. Check to be sure that you have all the necessary parts for your building. If you find any parts missing during construction call: or write: CUSTOMER SERVICE 0 North Fourth Street Breese, Illinois Please include your Model Number, Part Number, and Part Name Keep this Assembly Manual for further reference. 4

26 x5 3 3