HSW45 Introduction. NanaWall HSW45 Standard Aluminum Framed Single Track Sliding System

Transcription

1 HSW45 Introduction NanaWall HSW45 Standard Aluminum Framed Single Track Sliding System The standard aluminum framed HSW45 System provides an efficient and convenient entrance system for residential, commercial and recreation applications. Easy to slide and easy to store, this system offers a new dimension in designing large exterior opening glass walls. To see these operable wall concepts in action, please visit and click on the Animations link. For benefits of all NanaWall systems, see the General Introduction section. For common features and a comparison between aluminum single track sliding, see the Aluminum Single Track Sliding Systems Introduction. Swing Entry/Exit Panel(s) Swing entry/exit panel can be included, if desired, at either or both side jambs. Swing panels can be inward or outward opening. Multitude of Stacking Possibilities Including Pocket Option(s) The panels can be stacked in a number of ways when the unit is opened; see Stacking Options for examples. The tracks can be laid out beyond the frame in a variety of confi gurations. Floor Track Optional Sills can be eliminated completely providing seamless transition between two spaces. Locking rods in panels engage in adjustable fl oor sockets. Design Flexibility Custom sizes - heights up to 10' and panel widths up to 3 3'. There is a variety of glazing choices (single glass, insulated glass, laminated glass, etc.). Weather Resistant This system is engineered to provide weather resistance, good structural performance and resistance to dust infiltration. Rated Swing Panel The Swing panel(s) or Egress door(s) within the system has been engineered for "normal" commercial traffi c and has been independently tested to half a million opening and closing cycles per AAMA 920. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 1

2 HSW45 Technical Description Technical Description General Description The HSW45 Sliding/Stacking System is an aluminum framed single track sliding system designed to provide an opening glass wall or storefront with any custom panel size; see Maximum Size Chart. An end panel can be a swing panel hinged to a side jamb. Swing panels are single acting but can be either inward or outward opening; see details in the cross-section drawings. This system features many possible confi gurations and stacking bay options; see drawings for possibilities. Frame, Panels, Tracks & Stacking Bays Head and side jambs are extruded aluminum; the nominal head jamb thickness is 2 3/4" (70 mm), and the nominal side jamb thickness is 1 3/4" (45 mm). Sills can be low profi le saddle sill or surface mounted. Also available is a no sill option with fl oor sockets only. The tracks can be laid out in a variety of confi gurations. Various stacking layouts are available as suggested in the drawings. Pocket stacking options are also available. Panels Swing panels and stiles and rails of sliding panels are extruded aluminum with interlocking tongue-and-groove profi les; see cross-section drawings. The nominal panel thickness is 1 3/4" (45 mm). Panels are pre-assembled and all pins and screws needed to assemble the frame are provided. Finishes In addition to the choices from the NanaWall Powder Coating Finish Chart, the full range of RAL high gloss and matte powder coatings are also available. Anodized and fl ouropolymer kynar painted fi nishes are also available. Glazing Glazed units can be supplied with 1/4 (6 mm) single tempered or laminated, 3/4 (20 mm) clear insulating tempered or insulating Low-E tempered glass, other high performing safety glass such as Heat Mirror, special tint, etc. or other glass on request. See Glazing in the General Introduction for other glass thickness possible. provided for effective seals between panels and between panels and frames. Sliding & Swinging Hardware For sliding panels, two load-bearing stainless steel uni-directional carriers are attached to the upper corners of each panel. Each carrier has one guide-roller and two horizontal counter-rotating wheels that roll in the track. Each wheel has sealed bearings and is coated with toughened Polyamide to ensure quiet running and optimal resistance to temperature extremes. Carriers can easily negotiate square or angled corners without mechanical switches. For swing panels, two to fi ve hinges per connection are provided to connect panels together and to connect panels to frames. Finish for zinc die cast hinges would be closest powder coat match to panel profi le. Available as an option are stainless steel hinges. Locking Hardware and Handle Options On sliding panels on a unit, one point locking hardware is provided, consisting of a bottom locking rod operated by a 180º turn of a fl at handle on the inside only. On designated sliding panels, an additional locking rod at the top is provided. If there are swing panels, there are the following hardware options: Multi-point Locking. Consisting of lever handles on both sides, a Schlage compatible lockset, lockable latch, deadbolt and rods at the top and the bottom. After turn of key or thumbturn, depression of handles withdraws latch, lifting of handle engages rods and turn of key or thumbturn engages deadbolt and locks. Deadbolt Lock. Consisting of push/pull handles on both sides with deadbolt(s) operated by a lockset. Turn of key or thumbturn operates lock. Available is a lockset option of having key operation on both sides. To keep the panel closed, a door closer should be fi eld installed. No Hardware. For panic hardware to be installed by others, the main entry panel can be supplied with no locking hardware. Handle finish Schemes: Standard- Stainless steel lever and fl at handles in brushed satin or black titanium fi nish. Push/pull handles in brushed stainless steel fi nish or nylon in dark brown or gray fi nish. Optional- Flat handles in closest powdercoat match to panel aluminum fi nish. Weatherstripping Weatherstripping, consisting of EPDM or brush seals, is NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

3 HSW45 Maximum Size Chart Frame Height of Unit 10'2 (3100) 9'10 (3000) 9'6 (2900) 9'2 (2800) 8'10 (2700) 8 6 (2600) 8 2 (2500) 7 10 (2400) NOTE: English dimensions are approximate. Dimensions in parenthesis are in millimeters The total number of panels in a unit is only restricted by structural steel considerations. Any custom size is possible up to the maximum size shown. Generally, the minimum width of each panel is 1'11" (600 mm). On chart indicates a horizontal mullion is needed for unit heights above 8'4" (2550 mm) such that no glass pane height is more than 8'0" (2440 mm). indicates maximum frame height possible for a given maximum panel width. The maximum size limits are based on the weight of a double glazed panel that has a net glass thickness of 5/16 (8mm). This glass can be insulated or single glazed. For greater net glass thickness, this maximum size chart will not apply. 7 6 (2300) 7 2 (2200) 6 10 (2100) 2 3 (700) 2 7 (800) 2 11 (900) 3 3 (1000) Panel Width SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 3

4 HSW45 Possible Stacking and Configurations Elevation drawings and plan views of typical possible stacking concepts. Please see referenced cross-section details. As there can be many other stacking possibilities, please submit your ideas and sketches to NanaWall Systems, Inc. for evaluation. Please note that the number of panels in a system are unlimited. A switch is defined as a break in the upper track at the head jamb to lead panels away from the opening to the stacking bay. Note: In all concepts, the swing panel can be either inswing or outswing. Concept 1 Perpendicular stacking within the opening adjacent to the swing panel. Concept 2 Parallel stacking outside the plane of the opening in front of the swing panel. Concept 3 Perpendicular stacking outside the plane of the opening on the same side as the swing panel. Concept 4 Diagonal stacking outside the plane of the opening with outswing panel NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

5 HSW45 Possible Stacking and Configuration Elevation drawings and plan views of typical possible stacking concepts. Please see referenced cross-section details. As there can be many other stacking possibilities, please submit your ideas and sketches to NanaWall Systems, Inc. for evaluation. Please note that the number of panels in a system are unlimited. A switch is defined as a break in the upper track at the head jamb to lead panels away from the opening to the stacking bay. Note: In all concepts, the swing panel can be either inswing or outswing. Concept 5 Perpendicular stacking outside the plane of the opening on opposite side of the swing panel. Concept 6 Parallel stacking outside the plane of the opening on opposite side of the swing panel. Concept 7 Parallel stacking within the opening. Concept 8 Compact stacking with unit offset from the adjacent wall SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 5

6 HSW45 Possible Stacking and Configuration Elevation drawings and plan views of typical possible stacking concepts. Please see referenced cross-section details. As there can be many other stacking possibilities, please submit your ideas and sketches to NanaWall Systems, Inc. for evaluation. Please note that the number of panels in a system are unlimited. A switch is defined as a break in the upper track at the head jamb to lead panels away from the opening to the stacking bay. Concepts 1 through 8 are also possible with 90 and 135 angle turns as generally shown below 90 cornerless option 135 cornerless option NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

7 All Cross Sectional Views Are Half Size HSW45 Section Details Detail 1.2 Head Jamb Detail 22.0 Low Profile Saddle Sill (For resistance against wind driven rain, drain connections by others necessary.) FFH Frame Height Detail 2.4 Flush Sill (No rating against wind driven rain.) Detail 27.0 Adjustable Floor Socket - no sill. (No water rating.) Detail 2.3 Surface Mounted Interior Sill SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 7

8 HSW45 Section Details All Cross Sectional Views Are Half Size Detail 11.0 Two Sliding Panels Detail 3.0 Swing Panel hinged to a side jamb Detail 6.2 Side jamb meeting sliding panel NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

9 All Cross Sectional Views Are Half Size HSW45 Section Details Detail 11.4 Sliding Panel meeting Swing Panel Detail 33.0 Two Sliding Panels meeting at 90 Detail 33.2 Two Sliding Panels meeting at 135 SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 9

10 HSW45 Section Details All Cross Sectional Views Are Half Size Typical Kickplate Typical Mullion Profile Typical Simulated Divided Lites Muntins with Spacer Between Insulated Glass (SDL) Typical Panel Profile with Single Glazing NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

11 All Cross Sectional Views Are Half Size HSW45 Suggested Typical Installation Detail A22 Head Jamb Detail A23 Head Jamb Detail A24 Head Jamb INSTALLATION NOTES Suggested Typical Installation drawings shown are very general and may not be suitable for any particular installation. Product placement, fasteners, fl ashing, waterproofi ng, sealant, trim and other details for specifi c surrounding conditions must be properly designed and provided by others. Panel Hinged at Right Side Jamb (Inward Opening) Installation Considerations The approximate weight of a panel with single glazing is 4.5 lbs/sq ft² and double-glazing is 5.5 lbs - 8 lbs/sq ft² respectively. The maximum vertical structural deflection of the header should be the lesser of L/720 of the span and 1/4 under full live and dead loads. The structural support for lateral loads must also be provided. An adjustable anchorage system (see Detail A23) is highly recommended at the head jamb. See Pre-Installation Preparation and Installation Guidelines in the General Introduction. An owner s manual with installation instructions is available upon request. NOTE: Overhead structural steel support must be provided for the entire length of the track and stacking bays. It is recommended that all building dead loads be applied to the header prior to installing the NanaWall. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only the building's live load can be used to meet the above requirements of L/720 or 1/4. If not, both the dead and live loads need to be considered. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 11

12 HSW45 Suggested Typical Installation All Cross Sectional Views Are Half Size Detail 20A Standard Sill Detail 22 Low Profile Saddle Sill* *Low Profile Saddle Sill for Inward or Outward Opening For resistance against wind driven rain, the following is recommended by others: 1. Remove the gasket covering the inner channel. 2. Provide necessary weepholes at the bottom of channels and on the outside face of the sill. 3. Make necessary drain connections. Ask NanaWall for a detailed drawing NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

13 NanaWall HSW45 - Standard Aluminum Framed Single Track Sliding System PART 1 - GENERAL 1.01 Summary Guide Specifications - Section HSW45 A. Section Includes: Individual panel aluminum and glass door system, including aluminum frame, tracks, threshold, sliding panels, swing panels, stacking bays, sliding/swinging and locking hardware, weather stripping, glass and glazing; designed to provide an opening glass wall or storefront, with sizes and configurations as shown on drawings and specified herein, with the NanaWall HSW45, the Standard Aluminum Framed Single Track Sliding System as supplied by NanaWall Systems, Inc References A. American Architectural Manufacturers Association (AAMA): 1. AAMA 611, Voluntary Specification for Anodized Architectural Aluminum. 2. AAMA 2604, Voluntary Specifications, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels. 3. AAMA 920, Operation / Cycling Performance B. American National Standards Institute (ANSI): 1. ANSI Z97.1, Safety Performance Specifications and Methods of Test for Safety Glazing Material Used In Buildings. C. Consumer Product Safety Commission (CPSC): 1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials Submittals A. Product Drawings: Indicate dimensioning, configuration, swing panels, stacking bay layout, typical head jamb, side jambs and sill details, type of glazing material and handle height. B. Product Data: Manufacturer s literature and Owner s Manual with installation instructions. C. Contract Closeout Submittal: Submit Owner s Manual from manufacturer. Identify with project name, location and completion date, and type and size of unit installed Quality Assurance A. Manufacturer: Provide complete, precision built, engineered, pre-fitted unit by a single source manufacturer with at least 25 years experience in the sale of folding/sliding door systems for large openings in the North American market. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. B. Performance Requirements: Provide from manufacturer that has independently tested typical units with the following minimum results: 1. Operation / Cycling Performance of Swing Panel: Provide system that when tested according to AAMA 920, there was no failure after 500,000 cycles (requirement for AW Performance Class). C. Installer Qualifications: Installer experienced in the installation of manufacturer s products or other similar products for large openings. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years Warranty A. Provide manufacturer s standard warranty against defects in materials and workmanship. B. Warranty Period: Ten years for roller and for seal failure of insulated glass supplied. For all other components, one year. (Two years if unit is installed by manufacturers certified trained installer) from date of delivery by manufacturer.) SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 13

14 HSW45 Guide Specifications - Section Site Conditions, Delivery, Storage and Handling A. In addition to general delivery, storage and handling requirements specified in Section 01600, comply with the following: 1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities. PART 2 - PRODUCTS 2.01 Supplier A. NANA WALL SYSTEMS, INC. HSW Meadow Creek Drive Corte Madera, CA Toll Free (800) Telephone: (415) Fax: (415) Website: info@nanawall.com B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior approval Materials A. Frames and Panels: From manufacturer s standard profiles, provide head tracks, stacking bays, side jambs, sliding panels, and swing panels attached to the side jambs, with dimensions shown on drawings. 1. Provide clear anodized aluminum head track with aluminum covers on both sides. 2. Provide panels with: Standard one lite [OR with horizontal mullion(s) at specified height(s) from the bottom of the panel] [OR with simulated divided lites in pattern as shown on drawings]. 3. Provide standard bottom rail [OR manufacturer s standard kickplate with height specified]. 4. Aluminum Extrusion: Extrusions with nominal thickness of.078 (2.0 mm). Alloy specified as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611, powder coated conforming to AAMA Aluminum Finish (including head track covers): Select from NanaWall Powder Coating Finish Chart of 50 standard colors [OR clear anodized] [OR select from range of RAL high gloss powder coated finishes available from manufacturer] [OR select from range of RAL matte powder coated finishes available from manufacturer] [OR select from range of flouropolymar kynar painted finish] [OR custom finish] B. Glass: 1. All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR Provide manufacturer s standard glass with dry glazing with glass stops on the inside only: ¼ (6 mm) tempered [OR ¼ (6 mm ) laminated] [OR 3/4' (20 mm ) double insulating clear safety glass] [OR ¾ (20 mm) double insulating Low-E argon fill safety glass] [OR other glass available from manufacturer, including glass with other total thickness] 2. Provide manufacturer s standard silver gray finish [OR dark bronze] glass spacers. Provide without capillary tubes [OR with capillary tubes]. C. Locking Hardware and Handles: 1. Main entry panel: On the main entry panel(s) for models with swing panel(s), provide manufacturer s standard lever handles on the inside and outside and a Schlage compatible lock set with a lockable latch and multi-point locking with a NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

15 Guide Specifications - Section HSW45 dead bolt and rods at the top and bottom. Rods to be concealed and not edge mounted. After turn of key or thumbturn, depression of handles withdraws latch. Lifting of handles engages rods and turn of key or thumb turn engages deadbolt and operates lock. Stainless steel lever handles in a brushed satin finish [OR stainless steel lever handles in a titanium black finish] [OR oil rubbed bronze solid brass lever handles] [OR satin nickel solid brass lever handles] [OR white solid brass lever handles] [OR other compatible handles] [OR on the main entry panel(s) for models with swing panel(s), provide manufacturer s push/pull handles with separate lock set and dead bolt] Push-pull handles in a brushed stainless steel finish [OR push-pull handles in a gray nylon finish] [OR push-pull handles in a white nylon finish] [OR push-pull handles in brown nylon finish] [OR other compatible handles]] SPECIFIER S NOTE: This option is recommended with a door closer. [OR on the main entry panel(s) for models with a swing panel(s), no hardware or locking to be provided by the manufacturer, but with field installed panic device by others.] [OR on the sliding panel to be opened first for models without a swing panel, provide manufacturer s standard L-shaped handle on the inside, flat handle on the outside and lock set with profile cylinder. Operation of lock set is by turn of key from the outside and with a thumbturn from the inside with a two point locking hardware operated by 180º turn of the handle.] Stainless steel L shaped handles in a titanium black finish [OR stainless steel L shaped handles in a brushed satin finish] [OR L shaped handles in a brown nylon finish] [OR L shaped handles in a gray nylon finish] [OR L shaped handles in a white nylon finish] [OR other compatible handles] [OR on the sliding panel to be opened first for models without a swing panel, provide manufactur er s standard flat handle on the inside and on the outside and a lock set with a profile cylinder. Operation of lock set is by turn of key from the outside and from the inside with a two point locking hardware operated by 180º turn of the handle. SPECIFIER S NOTE: Key operation from the inside may not meet egress requirements.] [OR on main entry panel, provide manufacturer s standard flat handle on inside only with concealed two point locking hardware operated by 180º turn of handle. SPECIFIER S NOTE: Note that with this option, the main entry panel is operable from inside only and that there is no latch.] 2. On all other secondary panels, provide manufacturer s standard flat handles [OR removable custodial handles] and concealed one or two point locking hardware operated by 180º turn of handle. 3. Flat handle finish: Stainless steel in a brushed satin finish [OR stainless steel in a titanium black finish] [OR closest powder coat match to aluminum profile finish] 4. Provide handle height centered at 41 3/8 [OR as specified] from bottom of panel. 5. Aluminum locking rods with standard fiber glass reinforced polyamide end caps at the bottom (and top on certain panels). Rods to have a stroke of 15/16 (24 mm). 6. If there are more than one profile cylinder on the units for a project, keyed alike [OR keyed differently]. D. Sliding & Swinging Hardware: Provide manufacturer s standard hardware. 1. For each sliding panel, provide 2 two wheeled, toughened polyamide covered steel unidirectional sliding panel carriers with a one wheeled, polyamide guide roller that are attached to the panels with steel rods. Maximum carrying capacity of two carriers on a panel to be 220 lbs (100 kgs). 2. For swing panels, provide manufacturer s standard zinc die cast powder coated hinges that are the closest match to finish of frame and panels [OR stainless steel hinges]. Provide stainless steel security hinge pins with set screws. 3. Adjustment: Provide system capable of specified amount of adjustments without removing panels from tracks. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 15

16 HSW45 Guide Specifications - Section E. Other Components: 1. Threshold: Provide aluminum Clear anodized flush sill [OR bronze anodized flush sill] [OR clear anodized Low Profile Saddle Sill] [OR bronze anodized Low Profile Saddle Sill] [OR no sill but with adjustable clear anodized floor sockets]. 2. Weather stripping: Provide manufacturer s standard double layer EPDM or brush seals at both the inner and outer edge of door panels or on frame between panels and between panels and frame. Single layer weather stripping will not be allowed. 3. Provide machine screws for connecting frame components Fabrication A. Use extruded aluminum frame and panel profiles, corner connectors and hinges, sliding hardware, locking hardware and handles, glass and glazing and weather stripping as specified herein to make a sliding glass wall. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions. B. Sizes and Configurations: See drawings for selected number and size of panels, location of swing panels, and location of tracks and stacking bays Accessories (Edit for project requirements.) A. Provide other side lites, transoms, corner posts, or single or double doors as per drawings provided. B. Provide the NanaScreen, a series of vertical, collapsible, pleated screen panels. Provide pleated screen material with floor tracking chain with 1/4 (5 mm) floor track. See drawings for selected number of panels and configuration. Provide aluminum top track, side jambs, and vertical struts: White powder coated [OR clear anodized] [OR dark bronze anodized] [OR select from range of RAL powder coated finishes available from manufacturer] NanaScreen installation within opening [OR extended beyond opening] PART 3 - EXECUTION 3.01 Erection A. Because of the large dimensions involved and the weight and movement of the panels, verify the structural integrity of the header such that the maximum deflection with live and loads is limited to be the lesser of l/720 of the span and 1/4 (6 mm). Similar structural support is needed for the stacking bay(s) and any upper track leading to it. Structural support for lateral loads such as wind load must be provided. It is recommended that all building dead loads be applied to the header prior to installing the NanaWall. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only the building's live load can be used to meet the above requirements of L/720 or 1/4 (6 mm). If not, both the dead and live loads need to be considered. B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no unevenness, bowing, or bumps on floor. C. Installation of units constitutes acceptance of existing conditions Installation A. Install frame in accordance with manufacturer s recommendations and installation Instructions. Properly flash and waterproof around the perimeter of the opening NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

17 Guide Specifications - Section HSW45 B. Installer to provide anchorage devices and to securely and rigidly fit frame in place, absolutely level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work. C. If necessary, provide drain connections from lower track. D. Install panels, handles and lock set in accordance with manufacturer s recommendations and installation instructions. E. If necessary, adjust hardware for proper operation. END OF SECTION DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to, compliance with building codes, safety codes, laws, or fitness for a particular purpose. The guide specifications is not intended to be verbatim as a project specification without appropriate modifications for the specific use intended and the particular requirements of a specific construction project. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 17