blu stone freestanding basins Installation Guide

Transcription

1 blu stone freesting basins Installation Guide SA0504 SA0506 SA0505 SA0507 SA0505N44

2 Attention Before Installation - We recommend that installation be done by a minimum of 2 people as a security precaution. Also make sure to adopt proper posture when lifting basin. - Adhere to all local building plumbing codes. The diagrams in this guide are not construction plans. They are visual aids. - For best results, floor must be level wall must be square with floor. Installation Requirements Please read instructions carefully so as to avoid any damage to fixture. 1. To ensure this product is installed properly, you must read follow se guidelines. 2. The owner/user of product must keep this information for future reference. 3. Consult local building codes to make sure installation complies with stards. 4. Remove unit from its packaging. Before disposing of it, inspect unit to make sure its in good shape. Should inspection reveal any damage or defect in finish, contact your distributor. The warranty does not cover damages or defects in finish once it has been installed. Blu Bathworks responsibility for shipping damages ceases upon delivery of product in good order to carrier. All complaints regarding damage due to transport must be made directly to carrier. 5. Place unit in bathroom before you start working. Conserve all nuts bolts. 6. To protect unit during installation, we recommend that you lay a piece of cardboard on bottom. 7. If unit is covered with polyethylene protective film, do not remove until installation is complete to grant maximum protection. However, remove film where any two surfaces will be in permanent contact. 8. Verify that all dimensions on plan are same as ones of unit. Installation Notes Important! Install this product according to installation guide. Product does have an overflow. Spout must provide a minimum of 5 reach for adequate clearance into basin. Our products must be installed by certified professionals only according to our installation guide as well as federal, provincial / state local building codes regulations. Technical Support Assistance If furr assistance is required, please contact: Product Support at (09:00 17:00hrs PST) or technical@blubathworks.com North America Blu Bathworks Inc. 188 Smi Street,Vancouver, BC, Canada, V6B 6A9 T F Please refer to blubathworks.com for warranty, terms & conditions under warranty & procedure for warranty service. 1

3 Installation for Freesting Basins SA0504 / SA0505 / SA0506 / SA0507 PREPARATION 1. Place pedestal into installed position. Ensure product is level when placed mounting holes are located at sides. 2. Carefully mark mounting hole locations for pedestal onto floor with a non-permanent marker. 3. To help recall pedestal position, trace a line along base of pedestal. 4. Carefully remove pedestal. PEDESTAL INSTALLATION 5. Drill pilot holes for floor mounting brackets 1 2 (12mm) inside line. 6. Install pedestal mounting hardware provided. Place a metal washer onto bolts insert bolts through mounting brackets into floor securely. Fig Return pedestal into position with mark on floor. 8. Install pedestal bracket to floor using two supplied screws. Fig 2. WARNING: DO NOT OVERTIGHTEN. Overtightening may damage products cause personal injury /or property damage. 2 Min 2" (51mm) Max 3 (76mm) from finished wall All dimensions based on recommended 3 gap between finished wall actual distance based on spout length to be confirmed by installer 1 Floor mounting brackets 11" Rear cut-out for drain Line of basin ½" (12mm) ¾" Mounting holes 1½" (35mm) ؼ" Ø(8mm) 2

4 SA0504 / SA0505 / SA0506 / SA FAUCET FAUCET AND AND DRAIN DRAIN CONNECTIONS CONNECTIONS (NOT (NOT SUPPLIED) SUPPLIED) 1. Connect 1. Connect to to faucet faucet according according to faucet to faucet instructions. instructions. 2. Connect 2. Connect tighten tighten trap trap to to drain. drain. 3. Turn 3. Turn ON ON supplies supplies to to faucet. faucet. 4. Purge 4. Purge air from air from HOT HOT & COLD & COLD by running by running for a for few a few seconds. seconds. 5. Fill 5. Fill lavatory lavatory with with.. 6. Check 6. Check for leaks for leaks at at drain drain connections. connections. 3

5 SA0505N Plastic Anchors for Concrete Floor 3 4 Silicon 5 14 " [370] 3¼" FAUCET AND DRAIN CONNECTIONS (NOT SUPPLIED) 1. Connect to faucet according to faucet instructions. 2. Connect tighten trap to drain. 3. Turn ON supplies to faucet. 4. Purge air from HOT & COLD by running for a few seconds. 5. Fill lavatory with. 6. Check for leaks at drain connections. silicon ¾" 4

6 blu stone cleaning & repair guide blu stone is Blu Bathworks signature eco-friendly stone collection; a durable, low maintenance hygienic material that is high pressure injection molded, non-porous anti-microbial. blu stone products are stain, scratch impact resistant, easy to clean: after each use, simply wipe with a soft cloth to remove any surface dirt. routine care Never expose blu stone to petroleum based products, such as paint removers, oven cleaners or or solvents (Note: personal hygiene products cosmetics will NOT damage surface) We recommend that stains are removed within 24 hours Do not directly cut on blu stone surface Blu Bathworks does not recommend exceeding US/ Canada maximum hot temperature regulations of 150ºF/65ºC, respectively. Exceeding stated temperatures could result in damage to blu stone products stard cleaning For stard cleaning of both gloss matte finishes, we recommend using widely available cleaning products such as Mr. Clean, Fantastik, VIM, CIF etc. Matte finished products may occasionally require a mildly abrasive product. blu stone matte finish: For more difficult stains, use a mildly abrasive cream cleanser such as Soft Scrub, Comet Soft Cleanser, CIF or VIM blu stone gloss finish: Do not use abrasive products or cream cleansers scratched or damaged surfaces blu stone matte finish: Ensure re is no surface dirt by flushing with Rub 600-grit sing block, provided, in a gentle circular motion Higher grit spaper may be required to blend repaired area to match existing product finish blu stone gloss finish: Ensure re is no surface dirt by flushing with We recommend sing area starting with 600, grit spaper: begin with lower number (coarser) grit followed with each higher number (finer) in ascending order Finish by polishing surface using a cloth white polishing compound for automobiles repairs For more extensive repairs, send a photograph of your blu stone product to Blu Customer Service (technical@blubathworks.com), who will inform you as to most appropriate methods to use. limited warranty Blu Bathworks ( Blu ) warranty on blu stone products covers all defects in materials manufacturing for a period of five (5) years from date of purchase. This limited warranty, starting on original purchase date, is only offered to original purchaser who acquires product directly from Blu or from its authorized dealers. This limited warranty does not apply to cases in which a product was incorrectly installed, nor to damage due to negligence, misuse, rmal shocks, cigarettes, flames, natural catastrophes or or accidents. Blu is not responsible for costs claims that may arise from purchase of a product unsuited to structure of existing building. Any transformation or alteration made to a Blu product automatically voids warranty. Blu s warranty is limited to repair or replacement (with a product of equal value), provided claim is made to an authorized dealer or directly to Blu, within warranty period. Labor costs any or expenses entailed by replacement of a Blu product are not covered by warranty. 5