ENGINEERING STRUCTURES

Transcription

1 ENGINEERING STRUCTURES

2 In the previous chapter we have employed the equations of equilibrium in order to determine the support / joint reactions acting on a single rigid body or a system of connected members treated as a single rigid body. Determination of the support / joint reactions constitutes only the first step of the analysis in engineering structures.

3 To determine the forces internal to an engineering structure, we must dismember the structure and analyze separate free body diagrams of individual members or combination of members which are mostly connected to each other using smooth pin connections.

4 Determination of joint reactions is of great importance in the selection of connection members that hold the structure as a whole.

5 From now on we will focus on the determination of the forces internal to a structure, that is, forces of action and reaction between the connected members.

6 An engineering structure is any connected system of members built to support or transfer forces and to safely withstand the loads applied to it.

7 Joint reactions always occur in pairs that are equal in magnitude and opposite in direction. If not isolated from the rest of the structure or the environment by means of a free body diagram, joint forces are not included in the diagram since they will be internal forces.

8 In order to determine the joint reactions, the structures must be separated into at least two or more parts. At these separation points the joint reactions become external forces and thus, are included in the equations of equilibrium. In this chapter trusses, frames and machines will be examined as engineering structures.

9 TRUSSES (KAFES SİSTEMLER) A framework composed of members joined at their ends to form a rigid structure is called a truss. Bridges, roof supports, derricks, grid line supports, motorway passages and other such structures are examples of trusses.

10 Structural members commonly used are I- beams, channels, angles, bars and special shapes which are fastened together at their ends by welding, riveted connections, or large bolts or pins using large plates named as gusset plates.

11 I-Beam (I-Kiriş) Channel Beam (U-Profil) A Gusset Plate (Bayrak) plakası Angled Beam Bar (Çubuk)) (Köşebent L profil)

12 For bridges and similar structures, plane trusses are commonly utilized in pairs with one truss assembly placed on each side of the structure. The combined weight of the roadway and vehicles is transferred to either side.

13

14

15

16

17

18

19

20 Simple Trusses The basic element of a plane truss is the triangle. Three bars joined by pins at their ends constitute a rigid frame. In planar trusses all bars and external forces acting on the system lie in a single plane. P A B C

21 Joint (Düğüm) A Support Reactions A Typical Roof Truss G B F Member (Çubuk) External Force A truss can be extended by adding extra tirangles to the system. Such trusses comprising only of trianges are called simple trusses basit kafesler. In a simple truss it is possible to check the rigidity of the truss and whether the joint forces can be determined or not by using the following equation: C E Support Reaction D m=2j-3 this should be satisfied for rigidity m : number of members j : number of joints

22 Assumptions * In a truss system it is assumed that all bars are two force members. The weights of members are neglected compared to the forces they are supporting. Therefore members work either in tension or compression. (Çeki) (Bası) If the weight of the bar is to be considered, we can replace the weight W of the member by two forces, each W/2 if the member is uniform, with one force acting at each end of the member.

23 ** When welded or riveted connections are used to join structural members, we may usually assume that the connection is a pin joint if the centerline of the members are concurrent at the joint. In this case the joint does not support any moment since it allows for the rotation of the members.

24 *** It is assumed in the analysis of simple trusses that all external forces are applied at the pin connections. **** Since bars used in trusses are long, slender elements they can support very little transverse loads or bending moments.

25 Determinaton of Zero-Force Members (Boş Çubukların Belirlenmesi) Determination of the zero-force members beforehand will generally facilitate the solution of the problem. 1.Rule: When there are three members of which two are collinear, the member which is not collinear will be a zero-force member. It is necessary to add a third member to maintain alignment of the two members and prevent buckling.

26 We see from a force summation in the y direction that the force F 3 in the third member must be zero and from the x direction that F 1 =F 2. This conclusion holds regardless of the angle q and holds also if the collinear members are in tension. If an external force in y direction were applied to the joint, then F 3 would no longer be zero.

27 2. Rule : When two noncollinear members are joined as shown, then in the absence of an external load at this joint, the forces in both members must be zero, as we can see from the two force summations.

28 Equal Force Members (Eşit Yük Taşıyan Elemanlar) When two pairs of collinear members are joined as shown, the forces in each pair must be equal and opposite. F 1 and F 2, F 3 and F 4 are collinear

29 Determine the Zero-Force Members in the plane truss:

30 The Zero-Force Members in the plane truss:

31 SOLUTION METHODS 1) METHOD OF JOINTS (Düğüm Yöntemi) This method for finding the forces in the members of a truss consists of satisfying the conditions of equilibrium for the forces acting on the connecting pin of each joint. The method therefore deals with the equilibrium of concurrent forces, and only two independent equilibrium equations are involved. F x 0 F 0 y

32 Sign convention (İşaret anlaşması): It is initially assumed that all the members work in tension. Therefore, when the FBDs of pins are being constructed, members are shown directed away from the joint. After employing the equations of equilibrium, if the result yields a positive value (+), it means that the member actually works in tension {T} (çeki), if the result yields a negative value (-), it means that the member works in compression {C} (bası).

33 Determine the force in members ED, DC, EC, EF, FC and FG of the loaded truss.

34 ED, DC, EC, EF, FC, FG

35 2) METHOD OF SECTIONS (Kesim Yöntemi) When analyzing plane trusses by the method of joints, we need only two of the three equilibrium equations because the procedures involve concurrent forces at each joint. We can take advantage of the third or moment equation of equilibrium by selecting an entire section of the truss for the free body in equilibrium under the action of nonconcurrent system of forces.

36 The Method of Sections is often employed when forces in limited number of members are asked for and is based on the two dimensional equilibrium of rigid bodies ( F x =0, F y =0, M=0). This method has the basic advantage that the force in almost any desired member may be found directly from an analysis of a section which has cut that member.

37 Thus, it is not necessary to proceed with the calculation from joint to joint until the member in question has been reached. In choosing a section of the truss, in general, not more than three members whose forces are unknown should be cut, since there are only three available independent equilibrium relations.

38 Once a truss is cut into two parts, one of the parts is taken into consideration and all the internal forces now become external from where the cut was passed. The forces are initially assumed as working in tension, so, they are shown directed away from the FBD. After employing the equations of equilibrium, if the result yields a positive value (+), it means that the member actually works in tension {T} (çeki), if the result yields a negative value (-), it means that the member works in compression {C} (bası).

39 Before starting to solve with this method, if necessary, the support reactions can be determined from the FBD of the whole truss and also zero-force members can be identified. It is very important to recognize that, only the forces acting on the part are considered, the forces acting on the other part, which is not considered, should not be included. The moment center can be any point on or out of the part in consideration.