DAYSONFAST Table of Contents

Transcription

1

2 DAYSONFAST Table of Contents What is DAYSONFAST? 4 DAYSONFAST Areas Of Application 5 DAYSONFAST Benefits And Advantages 8 DAYSONFAST Technical Specifications 9 DAYSONFAST General Instructions 10 DAYSONFAST Instructions For Use 11 - Preparation of Solution Accelerators 11 - Preparation Of The Surface 11 - Application 11 According to ETAG005 (ETA 09/0016) Flat Roof Waterproofing 13 ETA Classification Roofing Applications 15 Packing 16 Storage 16 2

3 Dayson, has a specialized team that offers its clients the necessary expertise and technical assistance for the proper managing of all types of applications, whether in the field of waterproofing and in various industrial applications. Dayson, is in a continuous process of expansion and investigation for new products through using latest high technologies. Liquid 100% polyurethane insulation materials, Very fast drying, water-based polyurethane bitumen-based products, Water-based polyurethane insulation materials, Molding polyurethane sealants used for 10-15cm wide joints, With products manufactured with the most advanced technologies, such as Polyurea; It responds to emerging insulation needs. Waterproofing, tensile, abrasion and excellent resistance to high elongation are the common points of our products produced with the latest technologies. (ISO 11600, EOTA Certification) 3

4 DAYSONFAST Two component water-based Bituminous Liquid Membrane for Heavy Duty Applications DaysonFast a rapid drying waterproofing material, featuring extremely high productivity properties. The material is based on a unique bituminous emulsion featuring outstanding flexibility properties and excellent adhesion to concrete and to metal surfaces. 4

5 DaysonFAST Product Uses Waterproofing underground foundations. Waterproofing basements floors and walls Waterproofing retaining walls Waterproofing Tunnels and Canals Waterproofing covered roofs and verandas Waterproofing of roofs in accordance to ETAG 005 part 5 5

6 Ensures waterproofing needs in hard conditions for highway, subway, train tunnels In the negative and positive insulation applications for water channels, petrochemical and water pipelines Especially in need of stem strength in areas such as parking, garden, balcony Waterproofing for above and below terrace For surfaces such as concrete and OSB Plant area Land area Drainage Insulation DaysonFast top coat DaysonFast primer Concrete ground 6

7 Waterproofing directly on pond above land area and pools Inner and outer waterproofing for chemical waste repositories Ensure the internal and external waterproofing for clean and waste water tanks Providing waterproofing with special primer on glossy surfaces such as ceramic and granite Waterproofing applications directly above all kinds of iron, galvanized steel, aluminum and trapeze steel According to 5 th part of ETAG 005 ensures roofs waterproofing 7

8 Benefits & Advantages Absolute waterproofing High productivity (up to 1,000 m 2 / day) Environmentally friendly Applied immediately - No concrete curing required Rapid Drying Extremely High Flexibility Forms a seamless & uniform film Radon-tight 8

9 General Instructions All surfaces to which DAYSON Fast Liquid Membrane is to be applied must be sound, stable and free from dirt, dust, loose debris, grease etc. DAYSON Fast Liquid Membrane is applied by a double head spraying machine. One nozzle sprays the DAYSON Fast Liquid Membrane and the second sprays the accelerator. DAYSON Fast Liquid M. can be applied over inclined planes, horizontal and vertical surfaces. DAYSON Fast Liquid Membrane should be thoroughly mixed for 5 minutes prior to use using the spraying machine s pump. DAYSON Fast Liquid Membrane and liquid accelerator are simultaneously sprayed at a ratio of 10:1 (10 DAYSON Fast Liquid Membrane: 1 Accelerator). Spray a quantity of 6.5 Kg / m2 of DAYSON Fast Liquid M. to obtain a dry layer of 4mm thick. Footstep is permitted 3 hours from spraying completion. Let dry for 5 days for a complete dry, depending on local whether 9

10 Instructions for use 1. Accelerator solution preparation: a. Solid accelerator should be diluted with water in a separate container prior to use: 80% water, 20% accelerator by weight. 25 kg of solid accelerator are dissolved in 100 L of water to prepare the liquid accelerator used for spraying. b. Thoroughly mix to obtain a homogeneous solution. 2. Surface preparation : a. All surfaces to which DAYSON Fast Liquid Membrane is to be applied must be sound, stable and free from dirt, dust, loose debris, oil, grease or honey combs etc. b. The primer is applied by spraying DAYSON Fast Liquid Membrane directly on the surface without the accelerator. c. Before applying as a primer, DAYSON Fast Liquid Membrane should be thoroughly circulate by using the spraying machine s pump for 5 minutes to obtain homogenous emulsion. d. The primer is sprayed under low pressure at a quantity of gr/m 2 ( gal/100 sq.ft) covering the surface with a thin, even layer, to result a black surface with no excess primer. e. Let dry for about 1 hour (depending on weather conditions) 3. Application : a. Place the DAYSON Fast Liquid Membrane container and the accelerator container next to the spraying machine. Introduce the suction hoses of each material to its specific container. Operate the machine and recycle the solutions. b. DAYSON Fast Liquid Membrane should be thoroughly mixed for 5 minutes prior to use using the spraying machine s pump. c. The accelerator should be applied to the DAYSON Fast Liquid Membrane in a foggy spray flow, using no excess accelerator but in a way the all the sprayed DAYSON Fast Liquid Membrane is covered by the accelerator. d. Check that water is exuded from the new layer in droplets and not streams. e. Check that the water exuded during the creation of the membranes is clear. Cloudy or brown water is a sign that the reaction is not complete and the membrane is impaired. f. Footsteps are permitted 3 hours from spraying completion. g. Let dry for 5 days for a complete dry, depending on local weather. h. Spraying should be done by moving the spraying gun at a continuous pace horizontally or vertically until achieving the required thickness. i. DAYSON Fast Liquid Membrane may be applied to damp but not waterlogged surfaces. i. Do not apply during rain or if rain is expected. The waterproofing layer has to be protected before backfilling with soil. Protect the waterproofing membrane with drainage sheets. The compaction of the backfilled to a distance of 2 m (6ft) from the wall should be done by a manual vibratory hand held compactor. 10

11 No heavy compaction equipment should be allowed to travel close to the waterproofed wall. The backfill should not contain any stones over 40 mm. DaysonFAST System Waterproofing of horizontal layers should be protected with nonwoven Polyester spun bonded geotextile with a CBR puncture strength over 1000 kn (BS EN ISO 12236), and a layer of screed or concrete. Concrete surface DaysonFast top coat Geotex fibre DaysonFast primer Concrete surface Beton Surface Concrete Mesh Eps - xps foam Surface Drainage foam Geotex fibre Bitumen or polyurethane products Geotex fibre Bitumen or polyurethane products Bitumen membrane and/or Polyurethane primer Surface DaysonFast top coat DaysonFast primer Concrete Surface Concrete 11

12 Technical properties : Description Property Standard Appearance: Emulsion: Dark brown Membrane: black Specific gravity 1.02 ± 0.01 Solid content 60 ±2 % Coverage kg/m2 ( gal/100 sq.ft) Dry film thickness mm ( mils) Flashpoint Non flammable Service temperature: -10 C to +60 C Application temperature: +5 C to 40 C Application temperature: Heat stability >90 C (194 F) ASTM D 2939 Cold flexibility < -20 C (<-4 F) ASTM D 522 Low temperature flexibility and crack Pass Conduct C ASTM C 836 Tensile Strength > 0.1 MPa (> 14.2 psi) ASTM D 412 Elongation at break > 1200 % ASTM D 412 Resistance to water pressure > 1 atm, 24 hr (>14.7 psi, 24 hr) DIN Water Vapor Penetration 0.35 perms ASTM E 96 Recovery ( % elongation) > 85% ASTM D412 Creep AT 100 C No creep DIN Resistance to Standing water Passed ASTM D2939 Bacterial attack in soil 30 days 40 C (104 F) Pass ASTM D

13 4. Waterproofing flat roofs (S1-S4) in accordance to ETAG 005 (certificate no. ETA 09/0016) a. Surface preparation - as above. Prime the surface with The Bituminous component of DAYSON Fast Liquid Membrane without accelerator at a quantity of approximately 250 gr/ sq. m. b. Apply to the wet primer the polyester non woven geotextile 200 g/sq.m tensile strength 2.5 kn/m, CBR puncture test 0.5 kn. c. Let dry for 1-2 hours d. Spray the geotextile with the bituminous component of DAYSON Fast Liquid Membrane (without accelerator) approximately 1 kg / sq. m, until the geotextile is fully impregnate and covered with a thin layer of material. e. Let dry for four hours f. Apply at 2-4 kg sq.m of DAYSON Fast Liquid Membrane with accelerator over the impregnated geotextile. g. Apply two layers of the geotextile in corners and around penetrations in the roof, soak each layer separately with DAYSON Fast Liquid Membrane without accelerator, and after drying spray as in paragraph g. h. Coating - it is recommended to coat the material with a high solar reflectance coating. Consult the manufacturer for instructions. 13

14 Description Property Standard Resistance to water vapour EN 1931 Sd value: 2.0 m μ value: 1350 Water tightness TR 003 dense: 0,1 atm over 24 h Resistance to wind loads (fully bonded assembled system,: ii) TR-004 >80 kpa on concrete Resistance to dynamic indentation TR-006 dense on concrete: category I 2 Resistance to static indentation TR-007 dense on concrete: category L 2 User load category on concrete P2 : I 2 / L 2 Resistance to fatigue movement TR-008; 1000 cycles W cycles / - 10 C dense Resistance to low temperatures TR-006 at 20 C TL 3 - dense after dyn. / stat.indentation EN C TR C adhesion: > 50 kpa Resistance to high temperatures TR C TH 4 dense after stat. indentation: category L 2 TR-009 Roof slope : S 1 to S 4 climatic zone category: S severe; working Resistance to heat ageing TR-011: 70 C life category: W 2 (200 d) dense after dyn. indentation category I 2 TR cycles at 10 C dense, no crack, no delamination TR-010 exposure: UV-radiation in the presence of 1000 MJ/m 2 (W3) TR-006 dense, category: I 2 moisture 10 C EN C Resistance to water ageing TR C exposure time 60 days (W 3), dense, category L 2 Resistance to plant roots * DIN 4062 proof in comparison with bitumen 14

15 ETA Classifications Application to the roof: Minimum layer thickness 1.5 mm Water vapor diffusion resistance factor µ 1350 Resistance to wind loads 50 kpa External fire performance EN Class F ROOF Reaction to fire EN Class F Statement on dangerous substances Does not contain any Levels of use categories according to ETAG 005 with relation to: Working life W2 Climatic zones M and S (Moderate and Severe) Imposed loads P1 to P2 (Low to Moderate on less compressible substrate, e.g Concrete/steel) Roof slope S1 to S4 Lowest surface temperature TL3 (-20ºC) Highest surface temperature TH4 (90ºC) Equipment care : After finishing the entire job replace the suction hoses of the DAYSONFAST in diesel oil and spry the left over DAYSONFAST in the system to a garbage container until getting clear solvent coming out from the nozzle. 15

16 Packaging DAYSONFAST is available in the following packaging options: DAYSONFAST: 1 ton IBC Cube/ 264 gallon cube 180 Kg Drum / 48 gallon drum Storage Store under cover out of direct sunlight and protect from extreme temperature. In tropical climates the product must be stored in an air-conditioned environment. In cold climates the product must be stored in heated environment (over 10 o C/50 o C). Do not freeze. Shelf life is up to 12 months when stored as above. NOTE: Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. For specific storage advice consult our representatives. For Safety detailed instructions please refer to safety sheets (MSDS) Warranty DAYSON's products are manufactured to rigid standards of quality. DAYSON makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Users must always refer to the most recent issue of the local product data publication for the product concerned. The user of the product must test the product's suitability for the intended application and purpose. Due to differences in materials, substrates and site conditions DAYSON assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including but not limited to, the implied warranty of merchantability, fitness for a particular purpose, nor any liability arising from any legal relationship. All orders are accepted subject to our current inventory, terms and conditions of sale and delivery. 16