VSW65 BeyondLiftSlide / SwingSlide Introduction

Transcription

1 VSW65 BeyondLiftSlide / SwingSlide Introduction VSW65 - BeyondLiftSlide The VSW65 BeyondLiftSlide is a wood-framed, individual panel sliding door system that makes large glass openings possible. With its single track, the custom system provides a clean line for a seamless transition from inside to outside. The VSW65 is easy to operate and can be designed to slide into a pocket. For years, architects have been trying to design projects with large glass walls that completely disappear when open a seamless transition from inside to outside that is also weather-resistant and easy to operate. Past solutions have had multiple tracks with thick wall requirements, were difficult to operate (since multiple panels were hooked together) and had limited weather resistance. The VSW65 addresses all these issues. The VSW65 is a multi-panel, single track sliding system with large glass walls that easily glide open and close, Closed panels lock end to end for an energy efficient seal and streamlined appearance. Each system is custom designed to the size and number of panels needed, and can have an almost unlimited number of panels. When open, the panels can be stored in a number of possible ways. Design Benefits: Creates a very large opening that gives a sense of more space Panels stack in a pocket outside the plane of the opening or hang unobtrusively to the side. This means the panels can be moved out of sight. All panels are in the same plane in a single track. This eliminates the need for bulky multi-tracks and thick walls for holding the tracks. Also possible to have panels acting as swing panels that can completely disappear in a pocket Slim sills, concealed hardware, and doors aligned edge-toedge mean clean lines and maximum view Sliding panels glide easily on a single head track Available with one or more single acting operable doors The VSW65 has been rated, certified and labeled in accordance with NFRC 100 and 200; see the Performance and Testing Results section for more details. Engineering Benefits: The wall can be very easily moved since each panel is moved independently and is not hooked to other panels The main weight is borne by the top track, which ensures smooth operation even when there is some dirt or debris in the bottom track Quiet and rattle-resistant operation because of sealed, ball bearing multi-roller running carriages Long-term ease of use with compensation and adjustment features High performance levels for air infiltration, water penetration, structural & thermal performance and forced entry Sustainable design features: energy efficiency, natural day lighting and passive ventilation Special Features of Nanawall VSW65 System Multitude of Stacking Possibilities - Including Pocket Options The panels can be stacked in a number of ways when the unit is opened; see Possible Stacking Options. The tracks can be laid out beyond the frame in a variety of configurations. Design Flexibility Custom sizes of frame heights up to 10 (3050 mm) and panel widths up to 5 (1525 mm) are possible. There is a variety of glazing choices (single glass, insulated glass, laminated glass, etc.), and a large selection of muntin layouts (horizontal mullions, SDLs, solid panels, higher bottom rails, etc.). VSW65 - SwingSlide (see Configurations 7 and 7A on page 5) The NanaWall VSW65 SwingSlide looks like a normal pair of French doors with fixed sidelights. The center swing doors provide all the functional and aesthetic benefits of French doors. The NanaWall advantage, though, is that the pair of single acting operable doors and the sidelights can also slide away to create unobstructed openings up to fourteen feet wide. Design Benefits Symmetrical center swing doors Flexibility of large opening glass walls Panels can stack unobtrusively to the side or out of sight in a pocket when open All panels are in the same plane in a single track Narrow stiles and rails maximize the glass area Hinges, sliding and multi-point locking hardware are concealed and integrated into the profiles Each system is a custom designed to the size needed. The maximum sliding panel width is 4 (1220 mm) and the maximum swing panel width is 3 3 (1000 mm). The maximum unit height is 10 (3050 mm) SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 1

2 Technical Description VSW65 BeyondLiftSlide / SwingSlide General Description The VSW65 is a Single Track Multi-panel Wood Framed Slider System, designed to provide a large opening glass wall or storefront with any custom panel size; see Maximum Size Chart. A panel adjacent to a sliding panel can be a swing panel that can also slide away with the sliding panels on an end panel attached to a side jamb. Swing panels are single acting but can be either inward or outward opening; see details in the cross-section drawings. Possible configurations and stacking bay options are many; see drawings for possibilities. Frame, Tracks & Stacking Bays The head jamb is extruded aluminum. The nominal head jamb thickness is 3 9/16 (90 mm) and the nominal side jamb thickness is 2 5/8 (66 mm). Various sill options are available. The tracks can be laid out in a variety of configurations. Various stacking layouts are available as suggested in the drawings. Pocket stacking options are also available. Panels Stiles and rails of panels are cross grained, triple laminated, solid wood with interlocking tongue-and-groove profiles; see cross-section drawings. The nominal panel thickness is 2 5/8 (66 mm). Standard woods are European pine, meranti or douglas fir. Other selected woods are also available. Frames and panels have a sanding sealer or a base coat applied to be field finished by others. Panels are pre-assembled; see Wood Finish Options in the General Introduction. Glazing Glazed units can be supplied with 15/16 (24 mm) insulating Low E tempered glass, clear insulating tempered, 1/4 (6 mm) single tempered or laminated, other high performing safety glass such as Heat Mirror, acoustic, special tint, etc. or other glass on request. A large selection of muntin layouts with mullions, solid panels, higher bottom rails, etc. is available. For a sliding panel with a swing panel hinged to it there is concealed locking on the edge of the panel to secure the swing panel. If there is a swing panel, there are the following additional hardware option on the primary swing panel(s). 1. Multi-point Locking. Consisting of lever handles on both sides, a Schlage compatible lockset, lockable latch, deadbolt and rods at the top and the bottom. Depression of handles withdraws latch, lifting of handles engages rods and turn of key or thumbturn engages deadbolt and locks. For a unit with a secondary inactive swing panel, available are matching dummy lever handles on both sides and a concealed flush bolt that operates the rods at the top and the bottom. 2. Deadbolt Lock. ADA approved pull handles on both sides with deadbolt(s) operated by a lockset. Turn of key or thumb turn operates lock. Lockset option of having key operation on both sides. To keep the panel closed, a door closer should be field installed, but please note that a door closer can only be installed for a swing panel that is attached to the side jamb. 3. No Hardware. For panic hardware to be installed by others, the main entry panel can be supplied with no locking hardware. Handle finish schemes: Standard-Stainless steel lever and flat handles in brushed satin or black titanium finish. Optional-Brass lever handles in oil rubbed or satin nickel and flat handles powdercoated dark brown or silver gray. Push/pull handles are available in dark brown or gray nylon finish. Weatherstripping Weatherstripping, consisting of EPDM or brush seals, is provided for effective seals between panels and between panels and frames. Sliding & Swinging Hardware Attached to the upper corners of each panel are load-bearing, stainless steel unidirectional carriers with two rollers each. Each roller has sealed bearings and is coated with toughened Polyimide to ensure quiet running and optimal resistance to extreme temperature. Locking Hardware and Handle Options On all swing panels and on sliding panels as needed, a two point locking hardware is provided, consisting of top and bottom locking rods operated by a 180 turn of a flat handle on the inside only or concealed flush bolt. On most sliding panels, the top rod interlocks the male locking receptacle with the female receptacle of the adjacent panel. The lower rod is thrown into the sill or striker plate NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

3 VSW65 BeyondLiftSlide / SwingSlide Maximum Size Chart NOTE: English Dimensions are approximate. Dimensions in parenthesis are in millimeters MAXIMUM UNIT HEIGHT 10 0 (3050) FRAME HEIGHT OF UNIT 9 6 (2900) 9 2 (2800) 8 10 (2700) 8 6 (2600) 8 2 (2500) 7 10 ((2400) 7 6 (2300) 7 2 (2200) MAXIMUM WIDTH OF SWING PANEL MAXIMUM WIDTH OF SLIDING PANEL FOR ALL STACKING OPTIONS EXCEPT BEYONDLIFTSLIDE MAXIMUM WIDTH OF SLIDING PANEL FOR BEYONDLIFTSLIDE 6 10 (2100) and less (600) (700) (800) (900) (1000) (1100) (1220) (1320) (1420) (1525) PANEL WIDTH Any custom size is possible up to the maximum size shown. The unit width is the panel width multiplied by the number of panels. For heights above 8 6 panels have to be stiffened with a horizontal mullion. The total number of panels in a unit is only restricted by structural steel consideration. Generally, the minimum width of each panel is 1 11 (600 mm). The Maximum size limits are based on the weight of insulated glass with a net glass thickness of 5 16 or (8mm) (each glass pane being 5 32 or (4 mm) thick). If thicker net glass is used on a panel, this maximum size chart will not apply. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 3

4 VSW65 Testing Results - Performance of the NanaWall VSW65 TYPE OF TEST LOW PROFILE SADDLE SILL *Air psf (75 Pa): 0.19 ASTM E-283, cfm/ft psf (300 Pa): 0.46 *Water Penetration: ASTM E-547 Structural Load Deflection ASTM E-330: pass No uncontrolled water psf (215 Pa) subject to the following adaptations of the sill in the field by others: 1. Remove the gaskets covering the inner channel. 2. Drill weep holes through the bottom of this channel (about one 1 x ¼ weep hole per panel.) 3. Drill weep holes through the lower front face of the sill to drain water collected to a lower point (about one 1 x ¼ weep hole per panel.) Please note that due to varying site requirements and conditions, these sills will not be prepared for drainage by NanaWall Systems, Inc. If this drainage system is desired, we recommend that a qualified professional construct this system on the project site strictly in accordance with instructions provided by NanaWall Systems, Inc. and in accordance with good waterproofing techniques. Note that in some applications drain connections may not be possible. No uncontrolled water 6 psf (300 Pa) With Further Sill Modifications - additional U channel on inside 1 ⅜ deep and ½ wide with two weepholes through to lower chamber of sill. Design Pressure psf (2390 Pa) Design Pressure psf (2390 Pa) See Design Windload Charts for other sized panels. Note that the structural test pressures were 50% higher than the design pressures. *Forced Entry Resistance In accordance with AAMA and CAWM 300 requirements NOTES * Excerpts of results of a 10 5 W x 7 10 H three panel VSW65 unit (1 swing panel attached to a side jamb and 2 sliding panels. 1 sliding panel has offset detail 6.4 on 1 side) with Low Profile Saddle Sill and reinforced locking tested by Architectural Testing, Inc., Fresno, CA, an independent testing laboratory in February Thermal Performance Rated, certified and labeled in accordance with NFRC 100 and 200 TYPE OF GLASS (1 LITE) EITHER 78 MM OR 95 MM STILES GLASS THICKNESS U-FACTOR STANDARD SILL SHGC LOW PROFILE SADDLE SILL 2010 ENERGY STAR U-FACTOR SHGC 2010 ENERGY STAR Double IG Clear (air filled) Double IG standard Low E (argon filled) Double IG standard Low E (argon filled and enhanced spacer) Double IG 272/SB 60 Low E (argon filled, enhanced spacer) Double IG Heat Mirror TC88 flipped Low E (argon filled) Double IG Heat Mirror TC88 flipped Low E (krypton filled) 15/16" /16" /16" /16" a a 15/16" a a 15/16" a a NOTES SHGC = Solar Heat Gain Coefficient a 2010 Energy Star Qualification Criteria: U-Factor <.32, SHGC <.30 for doors in all climate zones. Call NanaWall for U-Factor & SHGC for other glass types NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

5 VSW65 BeyondLiftSlide / SwingSlide Possible Stacking Options As there can be many other possibilities, please submit your ideas and sketches to NanaWall Systems, Inc. for evaluation. Please note that the number of panels possible is unlimited (except with stacking option 7). NanaWall VSW65 BeyondLiftSlide 3 Parallel stacking in pocket - unit installed offset from the wall opening 1B Parallel stacking in pocket 6 Parallel stacking in front of open swing panel that is attached to the side jamb NanaWall VSW65 SwingSlide 7 Center Swing panels hinged off sliding panels - all parallel stacking in pocket on both sides Note: For a swing panel hinged to a sliding panel, limitation is that there can only be a total of 2 panels stacking on that side. 7a Swing panel hinged off sliding panel - one side only. Other side can be any of the other stacking options shown above. Note: Any numbers of panels can be stacked on this side using stacking option 1B, 3 or 6. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 5

6 VSW65 BeyondLiftSlide / SwingSlide Elevation Drawings of Possible Configurations For NanaWall VSW65 BeyondLiftSlide Stacking Option 3 As there can be many other possibilities, please submit your ideas and sketches to NanaWall Systems, Inc. for evaluation. Please note that the number of panels possible is unlimited (except with Stacking Option 7). For Stacking Option 1B For Stacking Option 6 For NanaWall VSW65 SwingSlide Stacking Option 7 For Stacking Option 7a NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

7 All Cross Sectional Views Are Half Size VSW65 BeyondLiftSlide / SwingSlide Section Details Detail 1.8 Head Jamb Detail 2.3 Low profile saddle sill (For resistance against wind driven rain, drain connections by others necessary.) Detail 2.5 Flush sill (no rating against wind driven rain.) SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 7

8 Section Details VSW65 BeyondLiftSlide / SwingSlide All Cross Sectional Views Are Half Size Detail 2.7 No sill. Adjustable floor sockets (no rating against wind driven rain. Only possible with Stacking Options 1B and 6.) NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

9 All Cross Sectional Views Are Half Size VSW65 BeyondLiftSlide / SwingSlide Section Details Nominal 3 1/16 (78 mm) and 4 3/4 (120 mm) are available as an option. Detail 3.0 Swing Panel Hinged to Right Side Jamb Detail 11.2 Swing Panel Hinged off Sliding Panel SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 9

10 Section Details VSW65 BeyondLiftSlide / SwingSlide All Cross Sectional Views Are Half Size Nominal 3 1/16 (78 mm) and 4 3/4 (120 mm) are available as an option. Detail 6.0 Side Jamb and Sliding Panel Detail 6.4 End sliding panel offsetting wall To be installed by others on adjacent wall NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

11 All Cross Sectional Views Are Half Size VSW65 BeyondLiftSlide / SwingSlide Section Details Nominal 3 1/16 (78 mm) and 4 3/4 (120 mm) are available as an option. Detail 11.0 Stiles of two sliding panels Detail 11.4 Sliding panel meeting swing panel, two swing panels meeting or two sliding panels meeting Detail 6.2 Wiggle panel hinged to sliding panel at side jamb SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 11

12 Section Details VSW65 BeyondLiftSlide / SwingSlide All Cross Sectional Views Are Half Size Typical Mullion Profile Typical Stile and Rail with Single ¼ Glass Typical Higher Bottom Rail Typical Simulated Divided Lites Muntins with Spacers Between Insulated Glass (SDL) NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

13 VSW65 BeyondLiftSlide / SwingSlide Suggested Typical Installation All Cross Sectional Views Are Half Size Head Jamb INSTALLATION NOTES Suggested Typical Installation drawings shown are very general and may not be suitable for any particular installation. Product placement, fasteners, flashing, waterproofing, sealant, trim and other details for specific surrounding conditions must be properly designed and provided by others. Installation Considerations The approximate weight of a panel with single-glazing is 4 lbs/ft 2 ; with double-glazing, the approximate weight is 5.5 lbs/ft 2. The maximum structural deflection of the header should be limited to the lesser of L/720 of the span and ¼ under full loads. The structural support for lateral loads, such as windload, must be provided. See Pre-Installation Preparation and Installation Guidelines in the General Introduction. An owner s manual with installation instructions is available upon request. Overhead structural steel support must be provided for the entire length of the track and stacking bays. Please consider the weight of all the panels at the stacking bay. Rough Opening From Subfloor Frame Height Low Profile Saddle Sill* It is recommended that all building dead loads be applied to the header prior to installing the NanaWall. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only the building s live load can be used to meet the above requirements of L/720 or 1/4. If not, both the dead and live loads need to be considered. *For Low Profile Saddle Sill: For resistance against wind driven rain, the following is recommended by others 1. Remove the gasket covering the inner channel. 2. Provide necessary weepholes at the bottom of channels and on the outside face of the sill. 3. Make necessary drain connections. Contact NanaWall for a detailed drawing. Panel Hinged at Right Side Jamb FFH FFH SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 13

14 Suggested Typical Installation VSW65 BeyondLiftSlide / SwingSlide All Cross Sectional Views Are Half Size INSTALLATION NOTES Suggested Typical Installation drawings shown are very general and may not be suitable for any particular installation. Product placement, fasteners, flashing, waterproofing, sealant, trim and other details fro specific surrounding conditions must be properly designed and provided by others. Installation Considerations The approximate weight of a panel with single-glazing is 4 lbs/ft 2 ; with double-glazing, the approximate weight is 5.5 lbs/ft 2. The maximum structural deflection of the header should be limited to the lesser of L/720 of the span and 1/4 under full loads. The structural support for lateral loads, such as windload, must be provided. See Pre-Installation Preparation and Installation Guidelines in the General Introduction. An owner s manual with installation instructions is available upon request. Overhead structural support must be provided for the entire length of the track and stacking bays. Please consider the weight of all the panels at the stacking bay. It is recommended that all building dead loads be applied to the header prior to installing the NanaWall. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only the building s live load can be used to meet the above requirements of L/720 or 1/4. If not, both the dead and live loads need to be considered. Standard Flush Sill NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

15 VSW65 Beyond LiftSlide / Swing Slide Design Windload Chart Standard Unit. (Derived From Comparative Analysis) Test Unit Size: 10 5 W x 7 10 H (3 panel unit with 1 swing panel attached to a side jamb and 2 sliding panels). Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/ or sizes may be restricted to what was tested. Please also note that chart is only applicable for units with referenced Nana Wall supplied locking. Both negative and positive pressures ALLOWABLE DESIGN WIND LOADING - PSF UNIT WIDTH DIVIDED BY NUMBER OF PANELS PANEL HEIGHT See Maximum Frame Size Chart for Possible Sizes SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 15

16 Guide Specifications - Section BeyondLiftSlide / SwingSlide VSW65 NanaWall VSW65 - BeyondLiftSlide and SwingSlide PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: Individual panel wood and glass door sliding system, including aluminum head jamb, tracks, stacking bays and threshold, wood frame side jambs, sliding panels and swing panels, sliding/swinging and locking hardware, weather stripping, glass and glazing; designed to provide an opening glass wall or storefront, with sizes and configurations as shown on drawings and specified herein, with the NanaWall VSW65 BeyondLiftSlide [OR SwingSlide] as supplied by Nana Wall Systems, Inc REFERENCES A. American Architectural Manufacturers Association (AAMA): 1. AAMA , Voluntary Specifications for Forced Entry Resistant Aluminum Sliding Glass Doors. B. American National Standards Institute (ANSI): 2. ANSI Z97.1, Safety Performance Specifications and Methods of Test for Safety Glazing Material Used In Buildings. C. American Society for Testing and Materials (ASTM): 1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 3. STM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential. D. Consumer Product Safety Commission (CPSC): 1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials. E. National Fenestration Rating Council (NFRC): 1. NFRC 100, Procedure for Determining Fenestration Product Thermal Materials. 2. NFRC 200, Procedure for Determining Solar Heat Gain Coefficient SUBMITTALS A. Detail Drawings: Indicate dimensioning, configuration, swing panels, stacking bay layout, typical head jamb, side jambs and sill details, type of glazing material and handle height. B. Product Data: Manufacturer s literature including independently tested data listing performance criteria and Owner s Manual with installation instructions. C. Contract Closeout Submittal: Submit Owner s Manual from manufacturer. Identify with project name, location and completion date, and type and size of unit installed QUALITY ASSURANCE A. Manufacturer: Provide complete, precision built, engineered, pre-fitted unit by a single source manufacturer with at least 20 years experience in providing single track systems for large openings in the North American market. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. 2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005 standard. B. Performance Requirements: Provide from manufacturer that has independently tested typical units. Testing results to include air infiltration in accordance with ASTM E 283, water penetration in accordance with ASTM E 547, structural loading in accordance with ASTM E 330, and forced entry in accordance with AAMA and CAWM ** SPECIFIER NOTE: Air infiltration and water penetration testing results can only be applicable if the unit matches the test unit in the direction of opening and the type of sill. Structural load testing results are only applicable for the test unit size and type of locking. (Comparative analysis charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures specifically required for the project). Forced entry testing results are only applicable for the test unit type of locking. See manufacturer s latest published data NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

17 BeyondLiftSlide / SwingSlide VSW65 Guide Specifications - Section C. Thermal Performance U value: Unit to be rated, certified and labeled in accordance with NFRC 100, shown in manufacturer s latest published data for the glazing, sill and direction of opening specified. D. Solar Heat Gain Coefficient: Unit to be rated, certified and labeled in accordance with NFRC 200, shown in manufacturer s latest published data for the glazing, sill, and direction of opening specified. E. Installer Qualifications: Installer experienced in the installation of manufacturer s products or other similar products for large openings. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years WARRANTY A. Provide manufacturer s standard warranty against defects in materials and workmanship. B. Warranty Period: Ten years for roller and for seal failure of insulated glass supplied. For all other components, one year (two years if unit is installed by manufacturer s certified trained installer) from date of delivery by manufacturer SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING A. In addition to general delivery, storage and handling requirements specified in Section 01600, comply with the following: B. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities. C. Do not subject wood components to extreme nor rapid changes in heat or humidity. Condition wood components to average prevailing relative humidity before installing. D. Do not use forced heat to dry out building. E. Store flat in dry, well ventilated area out of direct sunlight. PART 2 - PRODUCTS 2.01 SUPPLIER A. NANA WALL SYSTEMS, INC. 707 Redwood Highway, Mill Valley, California Toll Free (800) Telephone: (415) Fax: (415) Website: info@nanawall.com 2.02 MATERIALS A. Head Jamb, Tracks, Stacking Bays, and Sill: From manufacturer s standard profiles, provide head tracks, stacking bays, and sill with dimensions shown on drawings. 1. Provide Clear anodized standard flush sill [OR bronze anodized, thermally broken with polyamide standard flush sill] [OR clear anodized, thermally broken with polyamide Low Profile Saddle Sill] [OR bronze anodized, thermally broken with polyamide Low Profile Saddle Sill] [OR no sill but with adjustable floor sockets]. 2. Aluminum: Extrusions with nominal thickness of.078 (2.0mm). Alloy specified as AlMgSi 0.5 with strength rated as 6063-T5 or F-22 (European standard). Finish: Anodized conforming to AAMA 611. B. Panels and Side Jambs: From manufacturer s standard profiles, provide panels and side jambs with dimensions shown on drawings or as needed for panel stability. 1. Provide panels with: Standard one lite SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 17

18 Guide Specifications - Section BeyondLiftSlide / SwingSlide VSW65 [OR with horizontal mullion(s) at specified height(s) from the bottom of the panel] [OR with simulated divided lites in pattern as shown on drawings]. 2. Provide stile width of 3 3/4 (95 mm) [OR 3 1/16 (78 mm)] [OR 4 3/4 (120mm)] [OR other]. Provide bottom rail width of 3 3/4 (95 mm) [OR higher bottom rail only with height specified between 5 and 12 ] 3. Type of Wood: Solid, three layer, cross-grained, kiln dried Douglas fir - PEFC [OR European pine] [OR meranti] [OR western hemlock] [OR spruce] [OR European oak] [OR sapeli mahogany] [OR cherry (interior applications only)] [OR maple (interior applications only)] [OR beech (interior applications only)] [OR laminated bamboo (interior applications only)] [OR other wood as selected] [OR selected FSC wood on request] 4. Construction of wood panels to include close tolerance mortise and tenon, glued and pinned corners. 5. Wood Finish: Finishes to be water based, opened pored C. Glass: Clear sanding sealer for stain [OR base coat applied for paint] SPECIFIER S NOTE: Before installation, the unit must be field finished with at least two coats for a final protected finish. 1. Provide manufacturer s standard glass and dry glazing with EPDM gaskets and glass stops fixed with hidden nails. Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR /16 (24 mm) insulating clear safety [OR 15/16 (24 mm) insulating argon filled Low-E safety] [OR 15/16 (24 mm) insulating krypton filled Heat Mirror TC88 safety] [OR 1/4 tempered (6mm)] [OR 1/4 laminated (6mm)] [OR other glass available from manufacturer]. 2. For insulated units, provide manufacturer s standard glass spacers. Provide without capillary tubes [OR with capillary tubes]. D. Locking Hardware and Handles: 1. Main entry panel: On the main entry panel for models with a swing panel, provide manufacturer s standard lever handles on the inside and outside, a Schlage compatible lock set with lockable latch, multi-point locking with a dead bolt and rods at the top and bottom on primary panel. Rods to be concealed and not edge mounted. Depression of handles withdraws latch. Lifting of handles engages rods and turn of key or thumb turn engages deadbolt and operates lock. [OR on the main entry panel for models with a swing panel, provide manufacturer s push/pull handles with separate lock set and dead bolt NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

19 BeyondLiftSlide / SwingSlide VSW65 Guide Specifications - Section SPECIFIER S NOTE: This option is recommended with a door closer.] [OR on the main entry panel for models with a swing panel, no hardware or locking to be provided by the manufacturer, but with field installed panic device by others.] [OR on the sliding panel to be opened first for models without a swing panel, provide manufacturer s standard L-shaped handle on the inside, flat handle on the outside and lock set with profile cylinder. Operation of lock set is by turn of key from the outside and with a thumbturn from the inside with a two point locking hardware operated by 180º turn of the handle.] [OR on the sliding panel to be opened first for models without a swing panel, provide manufacturer s standard flat handle on the inside and on the outside and a lock set with a profile cylinder. Operation of lock set is by turn of key from the outside and from the inside with a two point locking hardware operated by 180º turn of the handle. SPECIFIER S NOTE: Key operation from the inside may not meet egress requirements.] [OR on main entry panel, provide manufacturer s standard flat handle on inside only with concealed two point locking hardware operated by 180º turn of handle. SPECIFIER S NOTE: Note that with this option, the main entry panel is operable from inside only and that there is no latch.] 2. On all other secondary panels, provide manufacturer s standard flat handles [OR removable custodial handles] and concealed two point locking hardware operated by 180 degree turn of handle. Face applied flush bolt locking will not be allowed. 3. Handle finish: Stainless steel lever, L shaped and flat handles in a titanium black finish [OR stainless steel lever, L shaped and flat handles in a brushed satin finish] [OR oil rubbed bronze solid brass lever handles and dark brown powder coated flat handles] [OR satin nickel solid brass lever handles and silver gray powder coated flat handles] [OR L shaped handles in a brown nylon finish and dark brown powder coated flat handles] [OR L shaped handles in a gray nylon finish and silver gray powder coated flat handles] [OR push-pull handles in a brown nylon finish and dark brown powder coated flat handles] [OR push-pull handles in a gray nylon finish and silver gray powder coated flat handles] SPECIFIER S NOTE: Note that other compatible lever handle styles and finishes are available from other suppliers.] 4. Provide handle height centered at 41 3/8 [OR as specified] from bottom of panel. 5. Aluminum locking rods with standard [OR reinforced to meet higher structural loading] fiber glass reinforced polyamide end caps at top and bottom. Rods to have a stroke of 15/16 (24 mm). 6. If there are more than one unit, keyed alike [OR keyed differently]. E. Sliding & Swinging Hardware: Provide manufacturer s standard hardware. 1. For each sliding panel, provide 2 two wheeled, toughened Polyamide covered stainless steel unidirectional sliding door carriers. Carrying capacity of each carrier to be 220 lbs. (100 kgs) 2. For each swing panel, provide manufacturer s standard clear anodized aluminum hinges [OR dark bronze anodized aluminum hinges] 3. Adjustment: Provide system capable of specified amount of adjustments without removing panels from tracks. F. Other Components: SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 19

20 Guide Specifications - Section BeyondLiftSlide / SwingSlide VSW65 1. Weather stripping: Provide manufacturer s standard double layer APTK at both the inner and outer edge of door panels or on frame for vertical sealing between panels and between panels and frame. Provide brush seals with flexible plastic web for all horizontal sealing. Single layer weather stripping will not be allowed. 2. Provide machine screws for connecting frame components FABRICATION A. Seal wood frame and panel wood members with a clear sand sealer or primer. B. Use frame, tracks, threshold, stacking bays, panel profiles, hinges, sliding/swinging hardware, locking hardware and handles, glass and glazing and weather stripping as specified herein to make an individual panel sliding opening glass wall. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions. C. Sizes and Configurations: See drawings for selected custom dimensions within the maximum frame sizes possible as indicated in manufacturer s literature. See drawings for selected number of panels, location of swing panels, and location of tracks and stacking bays ACCESSORIES (EDIT FOR PROJECT REQUIREMENTS) A. Provide other side lites, transoms, corner posts, or single or double doors as per drawings provided. B. Provide the NanaScreen, a series of vertical, collapsible, pleated screen panels. Provide pleated screen material with floor tracking chain with 1/4 (5 mm) floor track. See drawings for selected number of panels and configuration. Part 3 Execution 3.01 ERECTION Provide aluminum top track, side jambs, and vertical struts: White powder coated [OR clear anodized] [OR dark bronze anodized] [OR powder coated select from range of RAL powder coated finishes available from manufacturer]. NanaScreen installation within opening [OR extended beyond opening] A. Because of the large dimensions involved and the weight and movement of the panels, verify the structural integrity of the header such that the maximum deflection with live and dead loads is limited to be the lesser of L/720 of the span and 1/4 (6 mm). Similar structural support is needed for the stacking bay(s) and any upper track leading to it. Structural support for lateral loads such as wind load must be provided. It is recommended that all building dead loads be applied to the header prior to installing the NanaWall. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only the building s live load can be used to meet the above requirements of L/720 or 1/4 (6 mm). If not, both the dead and live loads need to be considered. B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no unevenness, bowing, or bumps on the floor. C. Installation of units constitutes acceptance of existing conditions INSTALLATION A. Install frame by qualified installer in accordance with manufacturer s recommendations and installation instructions. For exterior applications, properly flash and waterproof around the perimeter of the opening. B. Installer to provide appropriate anchorage devices and to securely and rigidly fit frame in place, absolutely level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work. C. If necessary, provide drain connections from lower track. D. Install panels, handles and lock set in accordance with manufacturer s recommendations and installation instructions. E. If necessary, adjust hardware for proper operation. F. Finishing: Field finish under Section Painting; seal and finish promptly after installation and prior to exposure to weather in accordance with manufacturer recommendations NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

21 BeyondLiftSlide / SwingSlide VSW65 Guide Specifications - Section END OF SECTION DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to, compliance with building codes, safety codes, laws, or fitness for a particular purpose. The guide specifications is not intended to be verbatim as a project specification without appropriate modifications for the specific use intended and the particular requirements of a specific construction project. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 21

22