Accreditation Scope by Certification Test Order

Transcription

1 Organization NEMA MW 1000 NEMA RE-2 Section 4.11 ASTM D149 ASTM D150 ASTM D256 ASTM D257 ASTM D495 ASTM D570 ASTM D635 ASTM D638 ASTM D790 ASTM D882 ASTM D1653 ASTM D1676 ASTM D1822 ASTM D1830 ASTM D1876 ASTM D1932 ASTM D2132 ASTM D2240 ASTM D2303 ASTM D2304 ASTM D2307 ASTM D2519 ASTM D3145 Magnet Wire Refrigerant Resistance/Extractable Title Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulation at Commercial Power Frequencies Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics Standard Test Methods for DC Resistance or Conductance of Insulating Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation Standard Test Method for Water Absorption of Plastics Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position Standard Test Method for Tensile Properties of Plastics Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Standard Test Method for Tensile Properties of Thin Plastic Sheeting Standard Test Method for Water Vapor Transmission of Organic Coating Films Standard Test Methods for Film-Insulated Magnet Wire Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Standard Test Method for Thermal Endurance of Flexible Sheet Used for Electrical Insulation by the Curved Electrode Method Standard Test Method for Peel Resistance of Adhesives Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes Standard Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Standard Test Method for Rubber Property - Durometer Hardness Standard Test Methods for Liquid-Contaminant, Inclined-Plane Tracking and Erosion of Insulating Standart Test Method for Thermal Endurance of Rigid Electrical Insulating Standard Test Method for Thermal Endurance of Film-Insulated Round Magnet Wire Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method Page 1 of 5

2 ASTM D3251 Standard Test for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire ASTM D3455 Standard Test Methods for Compatibility of Construction Material with Electrical Insulating Oil of Petroleum Origin ASTM D3638 Standard Test Method for Comparative Tracking Index of Electrical Insulating ASTM D3755 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Under Direct-Voltage Stress ASTM D3801 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position ASTM D3874 Standard Test Method for Ignition of by Hot Wire Sources ASTM D4804 Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics ASTM D5048 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn - Through of Solid Plastics Using a 125-mm Flame ASTM D5642 Standard Test Method for Sealed Tube Chemical Compatibility Test ASTM D6194 Standard Test Method for Glow-Wire Ignition of ASTM E96/96M Standard Test Methods for Water Vapor Transmission of ASTM E162 Standard Test Method for Surface Flammability of Using a Radiant Heat Energy Source UL 94 Tests for Flammability of Plastic for Parts in Device and Appliances Sections 7, 8, 9, 10, 11 UL 746A Polymeric Short Term Property Evaluations Sections 10, 11, 12, 13, 14, 15, 16, 20, 21, 22, 23, 24, 25, 26, 31, 32, 33, 34, 35, 38 UL 746B Polymeric Long term Property Evaluations Sections 6-17, 19, 20, and 20A UL 746C Polymeric - Use in Electrical Equipment Evaluations Sections 9, 10, 11, 12, 13, 14, 16, 17, 35, 51, 51 UL 1446 Systems of Insulating General UL 1441 Coated electrical sleeving Sections 5.6 and 5.7 UL 984 Compatibility Section 41 UL 2353 Single Multi-Layer Insulated Winding 1 Wire UL 2157/CSA-22.2 Long Term Exposure Sections 26.13, 26.14, , , 26.5, 26.6, 26.12, and No / Sections thru IEC Rotating electrical machines Part 1: Rating and performance IEC Rotating electrical machines - Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines IEC Rotating electrical machines - Functional evaluation of insulation systems - General guidelines IEC Rotating electrical machines - Test procedures for wire-wound windings - Thermal evaluation and classification IEC procedures for wire-wound windings - Classification of changes and insulation component substitutions Page 2 of 5

3 IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC Accreditation Scope by Certification Test Order procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines procedures for form-wound windings - Evaluation by electrical endurance procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses procedures for form-wound windings - Evaluation of thermomechanical endurance of insulation systems Rotating electrical machines - Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests Rotating electrical machines - Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters Rotating electrical machines - Selection of energy-efficient motors including variable speed applications - Application guide Power transformers Part 3 Insulation levels dielectric tests and external clearances in air Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials Method for the determination of the proof and the comparative tracking indices of solid insulating materials Methods of test for the determination of the insulation resistance of solid insulating materials Test procedure for the determination of the temperature index of enameled winding wires Electrical insulating materials - Thermal endurance properties - Ageing procedures and evaluation of test results Electrical insulating materials - Thermal endurance properties - Guide for the determination of thermal endurance properties of electrical insulating materials - Choice of test criteria Electrical insulating materials - Thermal endurance properties - Determination of thermal endurance indices (TI and RTE) of an insulating material using the fixed time frame method Electric strength of insulating materials - Tests at power frequencies Electric strength of insulating materials -Additional requirements for tests using direct voltage Recommended test methods for determining the relative resistance of insulating materials to breakdown by surface discharges Evaluation and qualification of electrical insulation systems Electrical insulating materials used under severe ambient conditions Test methods for evaluating resistance to tracking and erosion Page 3 of 5

4 IEC Glowing/hot-wire based test methods Glow-wire apparatus and common test procedure IEC Glowing/hot-wire based test methods Glow-wire flammability test method for end-products IEC Glowing/hot-wire based test methods Glow-wire flammability test method for materials IEC Glowing/hot-wire based test methods Glow-wire ignitability test method for materials IEC Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure IEC Fire hazard testing: Test Flames 500W W flame test methods IEC Test on gases evolved during combustion of materials from cables: Halogen acid gas content IEC Test on gases evolved during combustion of materials from cables: Acidity by ph measurement and conductivity IEC Winding wires - Test Methods - Chemical properties IEC Guide for test procedure for the measurement of loss tangent of coils and bars for machine windings IEC Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate IEC Measurement of smoke density of cables burning under defined conditions IEC Dry, solid insulating materials - Resistance test to high-voltage, low-current arc discharges IEC Electrical insulation systems Procedures for thermal evaluation IEC Specific requirements for general-purpose models Wire-wound applications IEC Specific requirements for encapsulated-coil model Wire-wound electrical insulation system IEC Electrical insulation systems - Procedures for thermal evaluation - Part 31: Applications with a designed life less than 5000 hours IEC Electrical insulation systems - Procedures for thermal evaluation - Multifactor evaluation by diagnostic procedures IEC Electrical insulation systems - Procedures for thermal evaluation - Multifactor evaluation with increased factors at elevated temperature IEC Electrical insulation systems- Procedures for thermal evaluation - Part 41: Specific requirements for electrical insulation systems for use in dry-type highvoltage transformers with operating voltages of 1kV and above IEC , -2 Electrical insulation systems Thermal evaluation of modifications to an established wire-wound and form wound EIS ISO 62 Plastics -- Determination of water absorption Page 4 of 5

5 ISO 178 ISO 180 ISO ISO ISO ISO 868 ISO 1210 ISO 8256 ISO 9773 IEEE 99 Sec. 9 IEEE 117 IEEE 259 IEEE 1043 IEEE 1776 (merger of IEEE 275 with IEEE 429) IEEE C IEEE C IEEE C Accreditation Scope by Certification Test Order Plastics Determination of flexural properties Plastics Determination of izod impact strength Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) Plastics -- Determination of the burning behavior of horizontal and vertical specimens in contact with a small-flame ignition source Plastics Determination of tensile-impact strength Plastics -- Determination of burning behavior of thin flexible vertical specimens in contact with a small-flame ignition source IEEE Recommended Practice for the Preparation of Test Procedures for the Thermal Evaluation of Insulation Systems for Electrical Equipment Test Procedure for Evaluation of Systems of Insulating for Random- Wound AC Electric Machinery Standard Test Procedure for Evaluation of 1 Systems of Insulation Dry Type Specialty and General-Purpose Transformers Recommended Practice for Voltage-Endurance Testing of Form-Wound Bars and Coils Recommended Practice for Thermal Evaluation of Unsealed or Sealed insulation Systems for AC Electric Machinery Employing Form Wound Pre-Insulated Stator Coils for Machines Rated 15,000 V and Below Test Procedure for Thermal Evaluation of Insulation Systems for Ventilated Dry- Type Power and Distribution Transformers Guide for Test Procedures for Thermal Evaluation of Insulation Systems for Dry- Type Power and Distribution Transformers, Including Open-Wound, Solid-Cast and Resin-Encapsulated Transformers Standard Test Procedure for Thermal Evaluation of Insulation Systems for Liquid-Immersed Distribution and Power Transformers Page 5 of 5