Missouri Correlations CEV Pathway: Building Trades Pathway

Transcription

1 CEV Multimedia Adoption 2010 Missouri s CEV Pathway: Building Pathway Meets 76% of standards for Air Conditioning, Heating and Refrigeration - pg 2 Meets 98% of standards for Agriculture Engineering Technology - pg 6 Meets 86% of standards for Carpentry - pg 9 Meets 91% of standards for Masonry - pg 14 Meets 74% of standards for Plumbing - pg 17

2 Building Pathway A. Appreciate and apply all personal and workplace safety procedures 1 Demonstrate appropriate work place safety practices (e.g., combustibles, electrical, hand tools, power tools, lockout/tagout, fall protection, refrigerants and pressurized gases) Tool Identification & Workplace Safety in Building ; Electricity, Plumbing & HVAC 2, 3, 4; 2, 3, 4, 5, 6, Safety & Operation of Tools, Hand Tool ID & Terminology - I, Hand Tool ID & Terminology - II, Hand Tool ID & Terminology - III, Basic Shop Safety, Basic Scaffolding: Safety & Assembly, Tool Security & Maintenance; Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Skills, Plumbing: Repair & Maintenance of a Sink & faucet Assembly, Plumbing: Repair & Maintenance of a Toilet, Plumbing: Material & Tool ID, Plumbing: Residential Systems, HVAC: Equipment & Test Instruments, HVAC: The Refrigeration Cycle 2 Identify types, purposes, and operation of fire Tool Identification & Workplace Safety in 4 Basic Shop Safety extinguishers and suppression systems Building 3 Inspect lab for hazards Tool Identification & Workplace Safety in 4 Basic Shop Safety Building 4 Recognize when first aid is needed for occupational Electricity, Plumbing & HVAC 2 Electrical Tools, Safety & Wiring injuries and follow proper procedures 5 Demonstrate victim removal procedures from an electrical conductor Electricity, Plumbing & HVAC 2 Electrical Tools, Safety & Wiring 6 Apply MSDS (Material Safety Data Sheet) information to Tool Identification & Workplace Safety in 4 Basic Shop Safety material use Building 7 Adhere to applicable local, state, and federal regulations Core Competency Disc Workplace Issues (EPA [environmental], DOT [moving vehicle] and OSHA [worker safety]) B. Identify and apply refrigeration principles and practices consistent with industry standards 1 Read and interpret pressure-temperature charts Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 2 Explain principles of refrigeration and heat transfer Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 3 theory Identify refrigerants/oil types and their characteristics Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments and uses 4 Operate a gauge manifold set Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments 5 Leak-test system Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments 6 Evacuate and measure vacuum level to 500 microns Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments 7 Recover and recycle refrigerants Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments 8 Charge system to manufacturer s specifications Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 9 Describe the operation of refrigeration system Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments accessories (e.g., receivers, accumulators, filter/dryer, sight glasses, and valves) C. Identify and apply piping principles and practices 1 Identify tubing and fitting types Electricity, Plumbing & HVAC 5 Plumbing Material & Tool ID 2 Perform copper tubing operations (e.g., cutting, flaring, Electricity, Plumbing & HVAC 5 Plumbing Material & Tool ID soldering, brazing, bending, and swaging) 3 Install, repair, and replace aluminum tubing Electricity, Plumbing & HVAC 5 Plumbing Material & Tool ID 4 Install and replace PVC tubing and pipe Electricity, Plumbing & HVAC 5 Plumbing Material & Tool ID Subject: 1 Course: Air Conditioning, Heating and Refrigeration

3 Building Pathway 5 Perform gas pipe operations (e.g., cutting, reaming, threading, and connecting) Electricity, Plumbing & HVAC 5 Plumbing Material & Tool ID D. Apply basic electrical theory to construct circuits and solve electrical circuit problems 1 Apply the principles of alternating and direct current Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Systems 2 Differentiate between common single- and three-phase voltage systems (e.g., 240V, 60Hz, single-phase; 208V, 60Hz, three-phase; 240V, 60Hz, three-phase; and 480V, 60Hz, three-phase systems) Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Systems 3 Read and interpret voltage, ampere, ohm, and watt Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments 4 meters Read and interpret electrical schematic and wiring diagrams Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Systems 5 Install electrical power and control circuits Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Systems 6 Apply the Ohm s law principles as related to series, Electricity, Plumbing & HVAC 3 Electrical Principles parallel, and series-parallel circuits 7 Apply the principles of electrical circuit protection (e.g., fuses, circuit breakers, disconnect switches, and grounds) Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Systems E. Identify and apply electrical motor principles and practices consistent with industry standards 1 Apply the operating principles of electric motors N/A N/A N/A 2 Recognize the application of various types of electric motors N/A N/A N/A 3 Recognize the application of various types of capacitors N/A N/A N/A 4 Test capacitors N/A N/A N/A 5 Explain the principles and operation of electric motor N/A N/A N/A protective devices 6 Interpret electric motor specifications (e.g., horsepower N/A N/A N/A and voltage) 7 Install and connect electric motors N/A N/A N/A F. Apply the principles of control systems consistent with industry and safety standards 1 Apply the principles of safety devices and operating Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments control circuits (e.g. pressure switches and thermostats) 2 Apply the principles of electromechanical control Electricity, Plumbing & HVAC 3 Electrical Principles devices (e.g., relays, contractors, magnetic starters, timers and sequences) 3 Apply the principles of electronic control devices (e.g., Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments ignition modules and electronic timers) 4 Install/service mechanical control devices (e.g., Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments pneumatic and water controls) 5 Install/service electromechanical control devices Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments 6 Install/replace transformers N/A N/A N/A G. Install and repair residential/light commercial cooling/heating systems consistent with industry and safety standards 1 Install or replace compressor Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 2 Install or replace condensing unit Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 3 Repair or replace condenser Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle Subject: 2 Course: Air Conditioning, Heating and Refrigeration

4 Building Pathway 4 Repair or replace evaporator Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 5 Replace, repair, and adjust metering devices Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 6 Clean up a contaminated system Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 7 Describe operation of a heat pump Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 8 Describe zoned heating and cooling systems Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 9 Start and check residential heating and cooling systems Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 10 Measure and adjust conditioned air flow Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 11 Describe vacuum pump and micron gauge applications Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 12 Repair, replace, and service electronic air cleaner Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 13 Pump down unit Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle H. Perform preventative maintenance on residential/light commercial cooling/heating systems 1 Perform preventive maintenance on air- conditioning Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle systems 2 Perform preventive maintenance on heating systems Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle 3 Perform preventive maintenance on heat pumps Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle I. Install air distribution system consistent with industry and safety standards 1 Design air-distribution system N/A N/A N/A 2 Fabricate, insulate, and install air-distribution systems N/A N/A N/A 3 Size and assemble vents N/A N/A N/A J. Troubleshoot residential/light commercial cooling/heating systems 1 Troubleshoot control devices (e.g., mechanical, N/A N/A N/A electromechanical and electronic) 2 Analyze compressor operation (e.g., electrical and N/A N/A N/A mechanical) 3 Analyze and replace a four-way reversing valve N/A N/A N/A 4 Troubleshoot electric motors N/A N/A N/A 5 Troubleshoot LP and natural gas fired heating systems N/A N/A N/A 6 Troubleshoot electric heating systems N/A N/A N/A 7 Troubleshoot heat pumps N/A N/A N/A 8 Troubleshoot oil-fired heating systems N/A N/A N/A 9 Troubleshoot air-conditioning systems N/A N/A N/A K. Demonstrate professional customer relations skills 1 Explain operation of the system s thermostat Electricity, Plumbing & HVAC 6 HVAC: Equipment & Test Instruments 2 Communicate system operation in lay terms Electricity, Plumbing & HVAC 6 HVAC: The Refrigeration Cycle L. Demonstrate leadership skills in the classroom, industry and society 1 Demonstrate an understanding of SkillsUSA, its structure and activities Core Competency Disc Jobs, Careers & Education 2 Demonstrate an understanding of one s personal values Core Competency Disc Jobs, Careers & Education 3 Perform tasks related to effective personal management Core Competency Disc Skills for Real World Survival skills 4 Demonstrate interpersonal skills Core Competency Disc All Lessons 5 Demonstrate etiquette and courtesy Core Competency Disc All Lessons 6 Demonstrate effectiveness in oral and written communication Core Competency Disc All Lessons Subject: 3 Course: Air Conditioning, Heating and Refrigeration

5 Building Pathway 7 Develop and maintain a code of professional ethics Core Competency Disc Skills for Real World Survival 8 Maintain an appropriate professional appearance Core Competency Disc All Lessons 9 Perform basic tasks related to securing and terminating Core Competency Disc Jobs, Careers & Education employment 10 Perform basic parliamentary procedures in a group Core Competency Disc Skills for Real World Survival meeting M. Explain and demonstrate skills in a specialization area identified by the instructor All MPUs All All Lessons Subject: 4 Course: Air Conditioning, Heating and Refrigeration

6 Building Pathway A. Construct Drawings 1 Demonstrate basic board drawing skills. Planning Effective Construction 2 Blue Prints: Planning a Building 2 Demonstrate basic CAD skills. Planning Effective Construction 2 Blue Prints: Planning a Building 3 Create a class schedule Career Guidance & Management in Building 1 Skills for Real World Survival 4 Create construction details Planning Effective Construction 2 Blue Prints: Planning a Building 5 Create floor plans Planning Effective Construction 2 Blue Prints: Planning a Building 6 Create building elevations Planning Effective Construction 2 Blue Prints: Planning a Building 7 Identify basic specification context Planning Effective Construction 2 Blue Prints: Planning a Building 8 Document materials used for specifications. Planning Effective Construction 2 Blue Prints: Planning a Building 9 Prepare preliminary and working drawings for wood frame Building Construction 2 Building Construction: Fundamentals residential construction and an intermediate-sized commercial B. Perform contract-related computer skills 1 Use programmable calculator. Career Guidance & Management in Building 1 Skills for Real World Survival 2 Use word processing. Career Guidance & Management in Building 1 Skills for Real World Survival 3 Use a spreadsheet Career Guidance & Management in Building 1 Skills for Real World Survival 4 Explain the process of developing architectural presentations using Planning Effective Construction 2 Blue Prints: Planning a Building appropriate computer software. C. Apply content-related mathematical skills 1 Solve problems using trig functions. Career Guidance & Management in Building 1 Skills for Real World Survival 2 Solve problems using algebraic equations activities. Career Guidance & Management in Building 1 Skills for Real World Survival 3 Solve problems using descriptive geometry. Career Guidance & Management in Building 1 Skills for Real World Survival 4 Perform conversions between measuring systems Planning Effective Construction 1 Marking & Measuring Devices D. Demonstrate measurement skills 1 Understand the conceptual difference between 2D and 3D. Planning Effective Construction 2 Blue Prints: Planning a Building 2 Use measuring tools. Planning Effective Construction 1 Marking & Measuring Devices 3 Perform and record onsite observation. Planning Effective Construction 1 Marking & Measuring Devices E. Effectively communicate orally and in writing 1 Develop materials for presentation. Career Guidance & Management in Building 1 Skills for Real World Survival 2 Develop and research background material. Career Guidance & Management in Building 1 Skills for Real World Survival 3 Demonstrate communications with co-workers. Career Guidance & Management in Building 1 Skills for Real World Survival 4 Demonstrate communications with external contacts. Career Guidance & Management in Building 1 Skills for Real World Survival 5 Demonstrate architectural presentation competencies. Career Guidance & Management in Building 1 Skills for Real World Survival F. Demonstrate teamwork in the engineering process 1 Conduct work in an ethical/professional manner Career Guidance & Management in Building 1 Skills for Real World Survival 2 Understand role within a team. Career Guidance & Management in Building 1 Skills for Real World Survival 3 Demonstrate responsibility in problem solving (team). Career Guidance & Management in Building 1 Skills for Real World Survival 4 Demonstrate responsibility in problem solving (individual). Career Guidance & Management in Building 1 Skills for Real World Survival G. Describe building materials and construction sequencing 1 Identify basic materials. Building Construction 2, 3, 4, 5, Building Construction: Fundamentals, Building Construction: Site Surveying & Development, Building Construction: Concrete & Masonry, Building Construction: Basic Masonry Subject: 1 Course: Architectural Engineering Technology - Technician

7 Building Pathway 2 Understand appropriate use of materials. Building Construction 2, 3, 4, 5, Building Construction: Fundamentals, Building Construction: Site Surveying & Development, Building Construction: Concrete & Masonry, Building Construction: Basic Masonry 3 Detail joining materials Building Construction 2, 3, 4, 5, 4 Understand critical sequencing of construction. Building Construction 2, 3, 4, 5, Building Construction: Fundamentals, Building Construction: Site Surveying & Development, Building Construction: Concrete & Masonry, Building Construction: Basic Masonry Building Construction: Fundamentals, Building Construction: Site Surveying & Development, Building Construction: Concrete & Masonry, Building Construction: Basic Masonry 5 Demonstrate concepts of energy conservation in building design. Building Construction; Planning Effective Construction 1; 1 Home Efficiency Service Checks; Non-Traditional Building Structures 6 Understand and demonstrate heat loss and heat gain calculations N/A N/A N/A in building design using computers. H. Perform material field testing 1 Identify appropriate site test, eg., Soil, Percolation. Building Construction 3 Building Construction: Site Surveying & Development 2 Understand implications of site test. Building Construction 3 Building Construction: Site Surveying & Development 3 Identify important construction material testing. Building Construction 2, 3, 4, 5, Building Construction: Fundamentals, Building Construction: Site Surveying & Development, Building Construction: Concrete & Masonry, Building Construction: Basic Masonry 4 Identify important construction material test, eg., welding, concrete. Building Construction 2, 3, 4, 5, Building Construction: Fundamentals, Building Construction: Site Surveying & Development, Building Construction: Concrete & Masonry, Building Construction: Basic Masonry I. Apply building-related codes to the design process 1 Understand application of International Building Code. Planning Effective Construction 2 Blue Prints: Planning a Building 2 Understand application of ADA. Planning Effective Construction 2 Blue Prints: Planning a Building 3 Understand application of Uniform Building Code. Planning Effective Construction 2 Blue Prints: Planning a Building J. Describe roles, relationships and responsibilities of engineering professionals 1 Understand role of surveyor. Career Guidance & Management in Building 3 Careers: Architecture & Construction 2 Understand role of civil engineer. Career Guidance & Management in Building 3 Careers: Architecture & Construction 3 Understand role of structural engineer. Career Guidance & Management in Building 3 Careers: Architecture & Construction 4 Understand role of mechanical/electrical engineer. Career Guidance & Management in Building 3 Careers: Architecture & Construction 5 Understand role of architect Career Guidance & Management in Building 3 Careers: Architecture & Construction 6 Understand role of contractor. Career Guidance & Management in Building 3 Careers: Architecture & Construction 7 Understand the history of architecture. Career Guidance & Management in Building 3 Careers: Architecture & Construction K. Analyze site characteristics Subject: 2 Course: Architectural Engineering Technology - Technician

8 Building Pathway 1 Understand site characteristics. Building Construction 3 Building Construction: Site Surveying & Development 2 Conduct site analysis. Building Construction 3 Building Construction: Site Surveying & Development L. Appreciate and apply all personal workplace safety procedures 1 Understand basic office site safety. Career Guidance & Management in Building 1 Workplace Issues 2 Understand basic job site safety. Career Guidance & Management in Building 1 Workplace Issues M. Demonstrate leadership skills in the classroom, industry and society 1 Demonstrate an understanding of Skills USA/VICA, its structure, Career Guidance & Management in Building 1 Jobs, Careers & Educations and activities. 2 Demonstrate an understanding of one s personal values. Career Guidance & Management in Building 2 Career Planning Basics 3 Perform task related to effective personal management. Career Guidance & Management in Building 1 Skills for Real World Survival 4 Demonstrate interpersonal skills. Career Guidance & Management in Building All Lessons 5 Demonstrate etiquette and courtesy Career Guidance & Management in Building All Lessons 6 Demonstrate effectiveness in oral and written communication. Career Guidance & Management in Building All Lessons 7 Develop and maintain a code of professional ethics. Career Guidance & Management in Building 1 Skills for Real World Survival 8 Maintain a good professional appearance. Career Guidance & Management in Building All Lessons 9 Perform basic task related to securing and terminating employment. Career Guidance & Management in Building 2 Career Planning Basics 10 Perform basic parliamentary procedures in a group meeting. Career Guidance & Management in Building 1 Skills for Real World Survival Subject: 3 Course: Architectural Engineering Technology - Technician

9 Building Pathway A. Describe and safely interact with all carpentry systems, including equipment, tools, codes, first aids, and applied academic skills. 1 Demonstrate appropriate safety practices All MPUs All All Lessons 2 Demonstrate knowledge of first-aid techniques Career Guidance & Management in Building 1 Workplace Issues 3 Identify and use measuring and layout tools Planning Effective Construction 1 Marking & Measuring Devices 4 Identify proper use and care of power and hand tools Tool Identification & Workplace Safety in Building 2, 3, 4 Safety & Operations of Tools, Hand Tool ID & Terminology - I, Hand Tool ID & Terminology - II, Hand Tool ID & Terminology - III, Tool Security & Maintenance 5 Identify and use nails and fasteners Building Construction 2 Building Construction: Fundamentals 6 Use pneumatic tools safely Tool Identification & Workplace Safety in 2 Safety & Operations of Tools Building 7 Estimate linear measurement, area, and volume Planning Effective Construction 2 Field Trip: Lumber Production 8 Construct scaffolding according to local, state, and/or national legislation Tool Identification & Workplace Safety in 4 Basic Scaffolding: Safety & Assembly Building 9 Identify purposes of building codes, zoning laws, and building permits Building Construction 3 Building Construction: Site Surveying & Development B. Demonstrate elements of construction planning 1 Read and interpret construction related documents (e.g., drawings, plans Building Construction 2 Building Construction: Fundamentals and blueprints) 2 Describe the steps of the building process Building Construction 2 Building Construction: Fundamentals 3 Estimate material and labor costs Planning Effective Construction 1 Planning Cost Effective Construction 4 Identify grades of lumber and plywood Planning Effective Construction 2 Field Trip: Lumber Production 5 Practice construction material quality control techniques (e.g., slump and Building Construction 4 Building Construction: Concrete & Masonry compaction tests) 6 Organize building materials Building Construction 2 Building Construction: Fundamentals C. Prepare the building site consistent with industry and safety standards 1 Analyze site excavation to be used (e.g., slab on grade, crawl space, or basement) Building Construction 3 Building Construction: Site Surveying & Development 2 Establish level/grade using appropriate instrumentation Building Construction 3 Building Construction: Site Surveying & Development 3 Lay out building Building Construction 3 Building Construction: Site Surveying & Development 4 Identify resources for locating utilities Building Construction 3 Building Construction: Site Surveying & Development D. Build and install construction forms consistent with industry and safety standards 1 Construct footing forms Building Construction 4 Building Construction: Concrete & Masonry 2 Install keyway for footing and foundations Building Construction 4 Building Construction: Concrete & Masonry 3 Erect wall forms (e.g., wood, manufactured, and new products) Building Construction 4 Building Construction: Concrete & Masonry 4 Strip and clean forms Building Construction 4 Building Construction: Concrete & Masonry 5 Lay out and install anchor bolts Building Construction 4 Building Construction: Concrete & Masonry 6 Install bulkhead Building Construction 4 Building Construction: Concrete & Masonry 7 Install expansion and contraction joint Building Construction 4 Building Construction: Concrete & Masonry 8 Waterproof foundation Building Construction 4 Building Construction: Concrete & Masonry 9 Install appropriate foundation drainage Building Construction 4 Building Construction: Concrete & Masonry 10 Identify and locate specified reinforcement materials Building Construction 4 Building Construction: Concrete & Masonry Subject: 1 Course: Carpentry

10 Building Pathway 11 Build and install forms/screeds for horizontal concrete (e.g., slab on grade) Building Construction 4 Building Construction: Concrete & Masonry E. Lay out and frame floor systems consistent with industry and safety standards 1 Demonstrate on-site crane rigging and safety procedures Building Construction 2 Building Construction: Fundamentals 2 Install termite shield N/A N/A N/A 3 Install beam Building Construction 2 Building Construction: Fundamentals 4 Install sill plate and sealer Building Construction 2 Building Construction: Fundamentals 5 Construct box sill Building Construction 2 Building Construction: Fundamentals 6 Lay out and install floor joists or truss system Building Construction 2 Building Construction: Fundamentals 7 Identify and layout specific wall and extra joist locations (e.g., under Building Construction 2 Building Construction: Fundamentals bathtubs or toilets) 8 Frame floor opening Building Construction 2 Building Construction: Fundamentals 9 Install subfloor Building Construction 2 Building Construction: Fundamentals 10 Install cross-bridging or strongback Building Construction 2 Building Construction: Fundamentals 11 Lay out, cut, and install stair system (e.g., stringers, treads, and risers) N/A N/A N/A F. Lay out and frame wall systems consistent with industry and safety standards 1 Lay out walls and framing members Building Construction 2 Building Construction: Fundamentals 2 Construct corner post Building Construction 2 Building Construction: Fundamentals 3 Construct, align, and brace stud partitions and walls Building Construction 2 Building Construction: Fundamentals 4 Identify and locate engineered materials Building Construction 2 Building Construction: Fundamentals 5 Frame openings (e.g., load-bearing or non load-bearing) Building Construction 2 Building Construction: Fundamentals 6 Install wind bracing Building Construction 2 Building Construction: Fundamentals 7 Install exterior wall sheathing Building Construction 2 Building Construction: Fundamentals 8 Install metal studs Building Construction 2 Building Construction: Fundamentals G. Lay out and frame roof system consistent with industry and safety standards 1 Lay out ceiling joist system Building Construction 2 Building Construction: Fundamentals 2 Install ceiling joists and stiff backs Building Construction 2 Building Construction: Fundamentals 3 Lay out, cut and install common rafter systems Building Construction 2 Building Construction: Fundamentals 4 Install roof truss systems Building Construction 2 Building Construction: Fundamentals 5 Lay out, cut and install roof (e.g., hips, valleys, jack and cripple rafters, and Building Construction 2 Building Construction: Fundamentals pearling) 6 Construct gable roof system Building Construction 2 Building Construction: Fundamentals 7 Lay out, cut and install gable studs Building Construction 2 Building Construction: Fundamentals 8 Apply roof sheathing Building Construction 2 Building Construction: Fundamentals 9 Frame roof openings Building Construction 2 Building Construction: Fundamentals H. Install roofing components consistent with industry and safety standards 1 Install roofing felt Building Construction 2 Building Construction: Fundamentals 2 Apply ventilation techniques and weather tightness techniques Building Construction 2 Building Construction: Fundamentals 3 Install flashing (e.g., chimney, step, and valley) N/A N/A N/A 4 Install roof ventilation systems (e.g., ridge vents, and box vents) Building Construction 2 Building Construction: Fundamentals 5 Install drip cap Building Construction 2 Building Construction: Fundamentals 6 Install composite shingle systems Building Construction 2 Building Construction: Fundamentals I. Install exterior finished consistent with industry and safety standards 1 Identify and describe exterior finishes (e.g., Nova brick, stackable masonry, Building Construction 5 Building Construction: Basic Masonry Hardi board, and concrete applied lap siding) 2 Install wood jamb window unit Building Construction 2 Building Construction: Fundamentals Subject: 2 Course: Carpentry

11 Building Pathway 3 Case exterior opening Building Construction 2 Building Construction: Fundamentals 4 Install pre-hung exterior door Building Construction 2 Building Construction: Fundamentals 5 Set metal window/door frames Building Construction 2 Building Construction: Fundamentals 6 Install drip cap over doors or windows Building Construction 2 Building Construction: Fundamentals 7 Install louvers/shutters N/A N/A N/A 8 Install metal, vinyl, and wood soffit/facia and siding N/A N/A N/A 9 Install columns N/A N/A N/A 10 Install and weatherproof storm doors and windows Building Construction 2 Building Construction: Fundamentals 11 Lay out, cut and install porches and decks N/A N/A N/A J. Install interior finishes consistent with industry and safety standards 1 Install batt insulation N/A N/A N/A 2 Install vapor barrier N/A N/A N/A 3 Install moldings N/A N/A N/A 4 Install interior door jambs and doors (e.g., pre-hung, double-acting, Building Construction 2 Building Construction: Fundamentals accordion, bypass, bifold, and pocket) 5 Install underlayment N/A N/A N/A 6 Install case and base trim N/A N/A N/A 7 Install interior hardware and accessories (e.g., doors, windows, kitchen, closet, bath, and cabinets) Electricity, Plumbing & HVAC 4, 5 Plumbing: Repair & Maintenance of a Sink and Faucet Assembly, Plumbing: Repair & Maintenance of a Toilet, Plumbing: Material & Tool ID, Plumbing: Residential Systems 8 Hang and finish drywall (gypsum) over wood or metal studs N/A N/A N/A 9 Install wall paneling N/A N/A N/A K. Perform basic electrical procedures consistent with industry and safety standards (exploration) 1 Apply basic fundamentals of electricity, including national and local electrical codes Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Skills 2 Apply proper wiring techniques Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Skills 3 Install/route wiring and components Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Skills 4 Install GFCIs (ground-fault circuit interrupters) Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Skills 5 Install Arc Fault protection Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Skills 6 Install devices, fixtures, and appliances Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principles, Residential Electrical Wiring Skills L. Perform basic concrete and masonry procedures consistent with industry and safety standards (exploration) 1 Identify characteristics of a mason and opportunities in the trade Career Guidance & Management in Building 3 Careers: Architecture & Construction 2 Install scaffolding Tool Identification & Workplace Safety in 4 Basic Scaffolding: Safety & Assembly Building 3 Identify and operate masonry tools Building Construction 4; 5 Building Construction: Concrete & Masonry, Building Construction: Basic Masonry 4 Identify and select masonry products Building Construction 4; 5 Building Construction: Concrete & Masonry, Building Construction: Basic Masonry 5 Practice proper anchoring and reinforcing procedures Building Construction 4; 5 Building Construction: Concrete & Masonry, Building Construction: Basic Masonry Subject: 3 Course: Carpentry

12 Building Pathway 6 Select masonry reinforcing materials Building Construction 4; 5 Building Construction: Concrete & Masonry, Building Construction: Basic Masonry 7 Identify components of chimneys, fireplaces, and wood-burning stoves N/A N/A N/A 8 Install wall and flooring tile N/A N/A N/A M. Perform basic plumbing procedures consistent with industry and safety standards (exploration) 1 Identify plumbing terminology (e.g., code applications) Electricity, Plumbing & HVAC 4, 5 Plumbing: Repair & Maintenance of a Sink and Faucet Assembly, Plumbing: Repair & Maintenance of a Toilet, Plumbing: Material & Tool ID, Plumbing: Residential Systems 2 Identify and select appropriate plumbing materials Electricity, Plumbing & HVAC 4, 5 Plumbing: Repair & Maintenance of a Sink and Faucet Assembly, Plumbing: Repair & Maintenance of a Toilet, Plumbing: Material & Tool ID, Plumbing: Residential Systems 3 Identify and operate plumbing tools (e.g., hand, torches, and power) Electricity, Plumbing & HVAC 4, 5 Plumbing: Repair & Maintenance of a Sink and Faucet Assembly, Plumbing: Repair & Maintenance of a Toilet, Plumbing: Material & Tool ID, Plumbing: Residential Systems 4 Locate and prepare for plumbing lines and fixtures Electricity, Plumbing & HVAC 4, 5 Plumbing: Repair & Maintenance of a Sink and Faucet Assembly, Plumbing: Repair & Maintenance of a Toilet, Plumbing: Material & Tool ID, Plumbing: Residential Systems 5 Install backing for fixtures Electricity, Plumbing & HVAC 4, 5 Plumbing: Repair & Maintenance of a Sink and Faucet Assembly, Plumbing: Repair & Maintenance of a Toilet, Plumbing: Material & Tool ID, Plumbing: Residential Systems N. Plan for HVAC systems consistent with industry and safety systems (exploration) 1 Describe general components of an HVAC system and how it functions (e.g., trunk lines for heat and return air, feeders, branch ducts, venting, and Electricity, Plumbing & HVAC 5 HVAC: Equipment & Test Instruments, HVAC: The Refrigeration Cycle power/fuel supply) 2 Locate and prepare for an HVAC system Electricity, Plumbing & HVAC 5 HVAC: Equipment & Test Instruments, HVAC: The Refrigeration Cycle O. Demonstrate leadership skills in the classroom, industry and society 1 Demonstrate an understanding of SkillsUSA, its structure and activities Career Guidance & Management in Building 1 Jobs, Careers & Education 2 Demonstrate an understanding of one s personal values Career Guidance & Management in Building 2 Career Planning Basics 3 Perform tasks related to effective personal management skills Career Guidance & Management in Building 1 Skills for Real World Survival 4 Demonstrate interpersonal skills Career Guidance & Management in Building All Lessons 5 Demonstrate etiquette and courtesy Career Guidance & Management in Building All Lessons 6 Demonstrate effectiveness in oral and written communication Career Guidance & Management in Building All Lessons 7 Develop and maintain a code of professional ethics Career Guidance & Management in Building 1 Skills for Real World Survival Subject: 4 Course: Carpentry

13 Building Pathway 8 Maintain an appropriate professional appearance Career Guidance & Management in Building All Lessons 9 Perform basic tasks related to securing and terminating employment Career Guidance & Management in Building 1 Jobs, Careers & Education 10 Perform basic parliamentary procedures in a group meeting Career Guidance & Management in Building 1 Skills for Real World Survival P. Explain and demonstrate skills in a specialization area identified by the instructor All MPUs All All Lessons Subject: 5 Course: Carpentry

14 Building Pathway A. Demonstrate employability skills 1 Identify employment opportunities and current trends in the Career Guidance & Management in Building 3 Careers: Architecture & Construction masonry trade 2 Describe employment requirements (e.g., drug testing) Career Guidance & Management in Building 3, 4 Careers: Architecture & Construction, Occupational Guidance for Agriculture 3 Identify personal responsibilities of employment (e.g., punctuality, good attitude, professional appearance, Career Guidance & Management in Building 1, 2 Skills for Real World Survival, Career Planning Basics accountability, and respect for diversity) B. Demonstrate basic trade and applied academic skills 1 Demonstrate basic reading and comprehension skills Career Guidance & Management in Building 1, 2 Skills for Real World Survival, Career Planning Basics 2 Solve job-specific mathematical calculations (e.g., basic ratio Building Construction 2 Building Construction: Fundamentals and proportion problems) 3 Read and interpret measuring instruments (e.g., rules, Planning Effective Construction 1 Marking & Measuring Devices spacing rules, and modular rules) 4 Identify types of scaffolding Tool Identification & Workplace Safety in Building 4 Basic Scaffolding: Safety & Assembly 5 Identify repair and maintenance procedures in the masonry trade Building Construction 4,5 Building Construction: Concrete & Masonry, 6 Use computer technology in the construction trade Planning Effective Construction 1 Computer Aided Design Techniques C. Appreciate and apply all personal and workplace safety skills 1 Complete a safety performance assessment for tools and Tool Identification & Workplace Safety in Building 2 Safety & Operation of Tools equipment 2 Demonstrate appropriate work place safety practices (e.g., Tool Identification & Workplace Safety in Building 4 Basic Shop Safety housekeeping, electrical, hand tools, power tools, fall protection, PPE, and environmental hazards) 3 Recognize when first aid is needed for occupational injuries Career Guidance & Management in Building 1 Workplace Issues and follow proper procedures 4 Identify types, purposes, and the operation of fire Tool Identification & Workplace Safety in Building 4 Basic Shop Safety extinguishers and suppression resources 5 Demonstrate proper techniques for lifting and carrying Building Construction 5 Building Construction: Basic Masonry 6 Demonstrate proper installation and use of scaffolding Tool Identification & Workplace Safety in Building 4 Basic Scaffolding: Safety & Assembly 7 List and describe government agencies that affect the masonry trade (e.g., OSHA, DNR, and building codes) Career Guidance & Management in Building 3, 4 Careers: Architecture & Construction, Occupational Guidance for Agriculture 8 Read and interpret Material Safety Data Sheets (MSDS) Tool Identification & Workplace Safety in Building 4 Basic Shop Safety D. Use basic hand and power tools consistent with industry and safety standards 1 Identify and use masonry hand and power tools Building Construction 4,5 Building Construction: Concrete & Masonry, 2 Select and use masonry hand and power tools Building Construction 4,5 Building Construction: Concrete & Masonry, 3 Maintain masonry hand and power tools Building Construction 4,5 Building Construction: Concrete & Masonry, E. Identify masonry materials and supplies 1 Identify masonry products (e.g., structural clay, concrete, natural, and mortar) Building Construction 4,5 Building Construction: Concrete & Masonry, 2 Identify additives, protectives, cleaning agents, sealants, and Building Construction 4,5 Building Construction: Concrete & Masonry, water repellants Subject: 1 Course: Masonry

15 Building Pathway 3 Identify artificial materials Building Construction 4,5 Building Construction: Concrete & Masonry, 4 Identify reinforcing materials Building Construction 4,5 Building Construction: Concrete & Masonry, 5 Identify insulated concrete forms (ICF) Building Construction 4,5 Building Construction: Concrete & Masonry, 6 Identify Concrete Form Masonry Units (e.g., grouted and installed by masons) Building Construction 4,5 Building Construction: Concrete & Masonry, 7 Describe new masonry products and emerging technologies Building Construction 5 F. Interpret designs, drawings and specifications 1 Read and interpret the architect s scale Planning Effective Construction 1 Marking & Measuring Devices 2 Read and interpret the engineer s scale Planning Effective Construction 1 Marking & Measuring Devices 3 Read and interpret masonry related documents (e.g., site plans, structural plans, mechanical plans, technical specifications, architectural blueprints, and electrical plans) Building Construction 2 Building Construction: Fundamentals 4 Read and interpret a set of specifications Planning Effective Construction 1, 2 Planning Cost Effective Construction, Blue Prints: Planning a Building 5 Read and interpret a finish schedule Planning Effective Construction 1, 2 Planning Cost Effective Construction, Blue Prints: Planning a Building 6 Estimate masonry materials for a job Planning Effective Construction 1, 2 Planning Cost Effective Construction, Blue Prints: Planning a Building G. Construct masonry structures consistent with industry and safety standards 1 Spread mortar (e.g., brick and block) Building Construction 5 2 Lay brick to a line with established leads Building Construction 5 3 Construct a 90-degree brick lead Building Construction 5 4 Lay 8 block to a line with established leads Building Construction 5 5 Construct a 90-degree block lead Building Construction 5 6 Lay out and construct a wall section with a joint Building Construction 5 reinforcement and openings 7 Construct an 8 brick wall Building Construction 5 8 Construct two 8 brick intersecting walls Building Construction 5 9 Identify arches, chases, pilasters, columns, and piers N/A N/A N/A 10 Install a rowlock brick window sill N/A N/A N/A 11 Describe layout procedures Building Construction 5 12 Describe pre-cast applications Building Construction 5 13 Install flashing, weeps, and cavity protection products N/A N/A N/A 14 Install Concrete Form Masonry Unit Building Construction 5 15 Install new pre-finished CMU walls (e.g., glazed, colored splitface, colored smooth, and groundface) N/A N/A N/A H. Clean, point and caulk masonry structures consistent with industry and safety standards 1 Apply hazardous materials safely (e.g., acids and strippers) Tool Identification & Workplace Safety in Building 4 Basic Shop Safety 2 Clean new brick walls with appropriate materials Building Construction 4 3 Clean existing brick walls with appropriate materials Building Construction 4 4 Repair or rebuild a masonry wall section Building Construction 4 5 Remove paint and stains from masonry wall faces N/A N/A N/A Subject: 2 Course: Masonry

16 Building Pathway 6 Caulk doors, windows, masonry, pre-cast, and concrete Building Construction 2 Building Construction: Fundamentals control joints 7 Demonstrate safe and proper procedures for below grade waterproofing and damp proofing applications Building Construction 4,5 Building Construction: Concrete & Masonry, 8 Demonstrate proper water repellant procedures for concrete and masonry Building Construction 4,5 Building Construction: Concrete & Masonry, 9 Clean pre-finished CMU walls (e.g., glazed, colored splitface, colored smooth, and groundface) N/A N/A N/A I. Demonstrate leadership skills in the classroom, industry and society 1 Demonstrate an understanding of SkillsUSA, its structure Career Guidance & Management in Building 1 Jobs, Careers & Education and activities 2 Demonstrate an understanding of one s personal values Career Guidance & Management in Building 2 Career Planning Basics 3 Perform tasks related to effective personal management Career Guidance & Management in Building 1 Skills for Real World Survival 4 Demonstrate skills interpersonal skills Career Guidance & Management in Building All All Lessons 5 Demonstrate etiquette and courtesy Career Guidance & Management in Building All All Lessons 6 Demonstrate effectiveness in oral and written Career Guidance & Management in Building All All Lessons 7 Develop communication and maintain a code of professional ethics Career Guidance & Management in Building 1 Skills for Real World Survival 8 Maintain an appropriate professional appearance Career Guidance & Management in Building All All Lessons 9 Perform basic tasks related to securing and terminating Career Guidance & Management in Building 1 Jobs, Careers & Education employment 10 Perform basic parliamentary procedures in a group meeting Career Guidance & Management in Building 1 Skills for Real World Survival J. Explain and demonstrate skills in a specialization area identified by the instructor All MPUs All All Lessons Subject: 3 Course: Masonry

17 Building Pathway 1 Safety 1 Demonstrate good safety practices [A01] Electricity, Plumbing & HVAC 4, 5 Plumbing: Repair & Maintenance of a Sink, Plumbing: Repair & Maintenance of a Toilet, Plumbing: Material & Tool ID, Plumbing: Residential Systems 2 Demonstrate proper techniques for lifting and carrying [A02] Building Construction 5 Building Construction: Basic Masonry 3 Exercise extreme caution when working around electric lines and equipment [A03] 4 Maintain work area properly [A04] Tool Identification & Workplace Safety in Building 5 Adhere to safety signs and color codes [A05] Tool Identification & Workplace Safety in Building 6 Identify and report potential safety hazards [A06] Tool Identification & Workplace Safety in Building 7 Practice ladder and scaffold safety [A07] Tool Identification & Workplace Safety in Building 8 Safely operate hand and power tools [A15] Tool Identification & Workplace Safety in Building 9 Properly handle gas cylinders, hoses, and regulators [A16] Tool Identification & Workplace Safety in Building 10 Wear required safety equipment [A09] Tool Identification & Workplace Safety in Building 11 Identify types of fire extinguishers and their proper uses [A12] Tool Identification & Workplace Safety in Building 12 Practice fire safety when operating heating equipment or working with hot materials [A13] 13 Demonstrate safe practices when using flux [A14] Tool Identification & Workplace Safety in Building 14 Demonstrate safe use of solvents [A17] Tool Identification & Workplace Safety in Building 15 Read and interpret MSDS sheets [A18] Tool Identification & Workplace Safety in Building 16 Demonstrate an awareness of locating and verifying buried utility lines [A19] Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principals, Residential Electrical Wiring Skills 4 Basic Shop Safety 4 Basic Shop Safety 4 Basic Shop Safety 4 Basic Scaffolding: Safety & Assembly 2 Safety & Operation of Tools 4 Basic Shop Safety 4 Basic Shop Safety 4 Basic Shop Safety Tool Identification & Workplace Safety in Building 4 Basic Shop Safety 4 Basic Shop Safety 4 Basic Shop Safety 4 Basic Shop Safety Electricity, Plumbing & HVAC 2, 3 Electrical Tools, Safety & Wiring, Electrical Principals, Residential Electrical Wiring Skills 17 Shoring and bracing excavation [A20] N/A N/A N/A 18 Demonstrate awareness of confined space entry [A21] N/A N/A N/A 19 Identify hazardous materials on site (i.e., leaking gas, Tool Identification & Workplace Safety in Building 4 Basic Shop Safety asbestos) [A22] 20 Work safely around laser equipment [A23] N/A N/A N/A 21 Demonstrate awareness of OSHA guidelines [A24] Career Guidance & Management in Building 1 Workplace Issues 22 Administer first aid and CPR [A25] Career Guidance & Management in Building 1 Workplace Issues 2 Pre-Employment Skills Subject: 1 Course: Plumbing

18 Building Pathway 1 Identify employment opportunities in the plumbing trade [J01] Career Guidance & Management in Building 3, 4 Careers: Architecture & Construction, Occupational Guidance for Agriculture 2 Complete a job application thoroughly [J02] Career Guidance & Management in Building 1, 2 Jobs, Careers & Education, Career Planning Basics 3 Develop and present a resume [J03] Career Guidance & Management in Building 1, 2 Skills for Real World Survival, Jobs, Careers & Education, Career Planning Basics 4 Maintain a professional appearance (neat, clean, groomed, appropriately dressed) [J04] Career Guidance & Management in Building 1, 2 Skills for Real World Survival, Career Planning Basics 5 Demonstrate effectiveness in oral and written communication [J05] Career Guidance & Management in Building 1, 2 Skills for Real World Survival, Career Planning Basics 6 Demonstrate good interpersonal skills [J06] Career Guidance & Management in Building 1, 2 Skills for Real World Survival, Career Planning Basics 7 Demonstrate a polite/respectful attitude [J07] Career Guidance & Management in Building 1, 2 Skills for Real World Survival, Career Planning Basics 8 Demonstrate good interviewing skills [J08] Career Guidance & Management in Building 2 Career Planning Basics 3 Basic Skills 1 Demonstrate basic reading skills [B12] Career Guidance & Management in Building 1, 2 Skills for Real World Survival, Career Planning Basics 2 Perform general mathematical calculations [B04] Building Construction 2 Building Construction: Fundamentals 3 Use good time management skills (i.e., efficient use of time on Career Guidance & Management in Building 1, 2 Skills for Real World Survival, Career job site) [B13] Planning Basics 4 Lay out and plan any given installation [B14] Planning Effective Construction 1, 2 Planning Cost Effective Construction, Blue Prints: Planning a Building 5 Define plumbing terminology [B02] Electricity, Plumbing & HVAC 4, 5 Plumbing: Repair & Maintenance of a Sink, Plumbing: Repair & Maintenance of a Toilet, Plumbing: Material & Tool ID, Plumbing: Residential Systems 6 Read and interpret Americans with Disabilities Act (ADA) Planning Effective Construction 2 Blue Prints: Planning a Building requirements [B15] 7 Read measuring devices [B03] Planning Effective Construction 1 Marking & Measuring Devices 8 Read and interpret a blueprint [B05] Planning Effective Construction 2 Blue Prints: Planning a Building 9 Sketch a plumbing layout [B06] Electricity, Plumbing & HVAC 5 Plumbing: Residential Systems 10 Read and interpret catalog and rough-in information [B07] Electricity, Plumbing & HVAC 5 Plumbing: Residential Systems 11 Read and interpret specifications [B08] Planning Effective Construction 1, 2 Planning Cost Effective Construction, Blue Prints: Planning a Building 12 Prepare a bill of materials [B09] Planning Effective Construction 1 Planning Cost Effective Construction 13 Read and interpret applicable codes [B10] Planning Effective Construction 2 Blue Prints: Planning a Building 14 Identify basic structural framing components [B11] Building Construction 2 Building Construction: Fundamentals 15 Use judgment for structural penetrations (i.e., drilling, cutting, Building Construction 2 Building Construction: Fundamentals notching) [B16] 16 Solder a 95/5 copper joint [B17] Electricity, Plumbing & HVAC 5 Plumbing: Material & Tool ID 17 Assemble a soft and rigid lead-free copper joint [B18] Electricity, Plumbing & HVAC 5 Plumbing: Material & Tool ID 18 Silver braze a copper joint [B19] Electricity, Plumbing & HVAC 5 Plumbing: Material & Tool ID Subject: 2 Course: Plumbing