Contract Design, Estimating and Documentation (CDED) Manual. CDED REVISION No. 216

Transcription

1 Contract Design, Estimating and Documentation (CDED) Manual CDED REVISION No. 216 July 13, 2017 The CDED Manual has been revised as detailed below and the documents are available for viewing and download, free of charge, from the MTO Technical Publications website at Chapter B - Detail Estimating Reference Code Existing Version New Version Implementation Date In CPS New (New), Revised (Rev), Cancelled (Can), Reissued (Rei) Chapter E - Standard Special Provisions (SSPs) Reference Code Existing Version E3-1 June 2017 New Version July S13 N/A July S14 February S17 N/A June 2017 Implementation Date In CPS July 20, 2017 July 13, 2017 N/A July 13, 2017 July 13, 2017 New (New), Revised (Rev), Cancelled (Can), Reissued (Rei) Rev: List of Active Standard Special Provisions is revised. New: SSP Amendment to OPSS 911, November Measurement of Coating Thickness is implemented to address identification, inspection, and repair of high mast lighting pole defects. Can: SSP Amendment to OPSS 905, November Inspection After Installation of Mechanical Connectors and Placing Reinforcement is cancelled. Applicable content has been included in new SSP 109S17. New: SSP Amendment to OPSS 905, November Delete and Replace Construction Specification for Steel Reinforcement for Concrete is implemented to address technical changes and the addition of requirements for welded wire reinforcement (WWR). Applicable content from SSP 109S14 and 109S56 has also been incorporated. July 13, 2017 (Revised July 20, 2017) Page 1 of 3 CDED Revision No. 216

2 Reference Code 109S56 Existing Version July 2016 New Version 111S12 N/A July S05 November S06 N/A June S01 N/A July F01 May 2017 Implementation Date In CPS N/A July 13, 2017 July 13, 2017 N/A July 13, 2017 July 2017 July 13, 2017 July 13, 2017 July 13, 2017 New (New), Revised (Rev), Cancelled (Can), Reissued (Rei) Can: SSP Amendment to OPSS 905, November 2014 is cancelled. Applicable content has been included in new SSP 109S17. New: SSP Amendment to OPSS 1103, November Delete and Replace SSP for Material Specification for Emulsified Asphalt is implemented. Can: SSP Amendment to OPSS 1440, November Fabrication of Reinforcing and Splice Bars is cancelled. Applicable content has been included in new SSP 114S06. New: SSP Amendment to OPSS 1440, November Delete and Replace SSP for Material Specification for Steel Reinforcement for Concrete is implemented to address technical changes and the addition of requirements for welded wire reinforcement (WWR). Applicable content from SSP 114S05 has also been incorporated. New: SSP Amendment to OPSS 2471, November Coating Inspectors and Inspection by the Owner is implemented. Rev: SSP Amendment to OPSS 517, November Design Storm Return Period and Preconstruction Survey Distance is revised with changes to the notes in Table A. Chapter G - Ministry of Transportation of Ontario Drawings (MTODs) Reference Code Existing Version New Version Implementation Date In CPS New (New), Revised (Rev), Cancelled (Can), Reissued (Rei) Chapter H - OPSSs and OPSDs Reference Code Existing Version New Version Implementation Date In CPS New (New), Revised (Rev), Cancelled (Can), Reissued (Rei) July 13, 2017 (Revised July 20, 2017) Page 2 of 3 CDED Revision No. 216

3 Chapter I - Structural Standard Drawings (SSDs) Reference Code Existing Version New Version Implementation Date In CPS New (New), Revised (Rev), Cancelled (Can), Reissued (Rei) I2-0 June 2017 July 2017 July 20, 2017 Rev: List of Active SSDs is revised. July 13, 2017 (Revised July 20, 2017) Page 3 of 3 CDED Revision No. 216

4

5 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs E3-1 - LIST OF ACTIVE STANDARD SPECIAL PROVISIONS S.P. # Title Issue Date Imp. Date 100S02 AMENDMENT TO MTO GENERAL CONDITIONS OF CONTRACT, NOVEMBER Ontario Provincial Standards 100F06 AMENDMENT TO MTO GENERAL CONDITIONS OF CONTRACT, NOVEMBER Tender Items Governed By Municipal-Oriented Specifications 100F08 PROTECTION OF PUBLIC TRAFFIC - Restrictions on Construction Operations 100S15 AMENDMENT TO MTO GENERAL CONDITIONS OF CONTRACT, NOVEMBER Utilities and Maintaining Roadways and Detours 100S21 AMENDMENT TO MTO GENERAL CONDITIONS OF CONTRACT, NOVEMBER Indemnification and Insurance Requirements Concerning the Canadian Pacific Railway Company 100S22 AMENDMENT TO MTO GENERAL CONDITIONS OF CONTRACT, NOVEMBER Indemnification and Insurance Requirements Concerning the Canadian National Railway Company 100F28 AMENDMENT TO MTO GENERAL CONDITIONS OF CONTRACT, NOVEMBER Property; Aircraft and Watercraft; Boiler; and Contractor s Equipment Insurance 100S59 AMENDMENT TO MTO GENERAL CONDITIONS OF CONTRACT, NOVEMBER Approvals and Permits, and Water Taking 100S62 AMENDMENT TO MTO GENERAL CONDITIONS OF CONTRACT, NOVEMBER Definitions, Substantial Performance, and Advance Payments for Material 101F02 AMENDMENT TO OPSS 120, NOVEMBER Identification of Waterbodies for Application of DFO Guidelines for the Use of Explosives In or Near Canadian Fisheries Waters 101S04 AMENDMENT TO OPSS 120, NOVEMBER Flyrock Incident Form - Part A Mar 2017 Jun 8, 2017 Nov 2016 Jan 12, 2017 Mar 2017 Jun 8, 2017 May 2017 Jun 8, 2017 Feb 2017 Mar 2, 2017 Nov 2016 Jan 12, 2017 Nov 2016 Jan 12, 2017 Nov 2016 Jan 12, 2017 Nov 2016 Jan 12, 2017 Dec 2014 Jan 8, 2015 Jan 2017 Jan 12, S11 ADDITIONAL EQUIPMENT - Equipment Option and Compensation Rates Mar 1985 Mar 1, S12 POWER RATINGS - Horse Power, Crawlers, Tractors, and Dozers Aug 1984 Aug 1, F13 LIQUIDATED DAMAGES - Inadequate Supply of Equipment, Labour and Material 101S18 AMENDMENT TO OPSS 102, OCTOBER Bar Coding on Material Delivery Invoices 101F21 OCCUPATIONAL HEALTH AND SAFETY ACT COMPLIANCE - List of Designated Substances 101F23 AMENDMENT TO OPSS 182, APRIL Timing of In-Water Works, Oversight Requirements, and Measures to Avoid Harm to Fish 102S05 AMENDMENT TO OPSS 206, NOVEMBER Various Revisions to Construction Specification for Grading Aug 1984 Aug 1, 1984 Apr 1994 May 11, 1994 Nov 2014 Nov 6, 2014 Apr 2017 Jun 8, 2017 May 2017 Jun 8, 2017 July 2017 (Rev. July 20, 2017) Page 1 of 13 CDED E3-1

6 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 103F02 AMENDMENT TO OPSS 313, NOVEMBER Submission Requirements and Production 103F03 AMENDMENT TO OPSS 313, NOVEMBER Construction Specification for Hot Mix Asphalt - End Result (Deletes and Replaces OPSS 313 In Its Entirety) 103F31 ASPHALTIC CONCRETE SURFACE SMOOTHNESS - Asphaltic Concrete Payment Adjustment for Surface Smoothness Based on Quality Assurance Measurements Taken by an Inertial Profiler Mar 2017 Mar 2, 2017 Jun 2017 Jun 8, 2017 Jun 2017 Jun 8, S39 AMENDMENT TO OPSS 350, MARCH Curing Compound Sep 2001 Oct 10, S06 AMENDMENT TO OPSS 421, NOVEMBER Post Installation Inspection 105S22 AMENDMENT TO OPSS 501, NOVEMBER Target Density Control Strip 106S05 106S09 (ELEC) 106S10 (ELEC) 106S16 (ELEC) AMENDMENT TO OPSS 106, APRIL Revisions to Definitions, Materials, and Construction for ATMS Work AMENDMENT TO OPSS 609, NOVEMBER Proof of Performance Testing and Inspection AMENDMENT TO OPSS 611, NOVEMBER Proof of Performance Testing and Inspection AMENDMENT TO OPSS 617, NOVEMBER Definitions and Proof of Performance Testing and Inspection 107S01 AMENDMENT TO OPSS 710, NOVEMBER Short Term Pavement Marking 107S02 AMENDMENT TO OPSS 710, NOVEMBER Sample and Application Requirements Feb 2016 Mar 03, 2016 Jun 2016 Sep 1, 2016 Jun 2017 Jun 8, 2017 Feb 2017 Mar 2, 2017 Feb 2017 Mar 2, 2017 Feb 2017 Mar 2, 2017 Sep 2011 Sep 29, 2011 Feb 2017 Mar 2, S04 AMENDMENT TO OPSS 740, NOVEMBER Steel Reinforcement Feb 2013 Mar 7, S05 AMENDMENT TO OPSS 706, NOVEMBER Freeway Paving Operations Apr 2017 Jun 8, S04 AMENDMENT TO OPSS 906, NOVEMBER 2012 Mar 2016 Mar 03, S12 AMENDMENT TO OPSS 902, NOVEMBER QVE, Backfilling Compaction, and Certificate of Conformance 109S13 AMENDMENT TO OPSS 911, NOVEMBER Measurement of Coating Thickness Feb 2017 Mar 2, 2017 Jul 2017 Jul 13, F16 TRANSPORTATION OF STRUCTURAL COMPONENTS - Background Feb 2009 Feb 19, S17 AMENDMENT TO OPSS 905, NOVEMBER Construction Specification for Steel Reinforcement for Concrete (Deletes and Replaces OPSS 905 In Its Entirety) Jun 2017 Jul 13, S22 INSTALLATION OF STEEL PINS Aug 1984 Aug 1, S23 TIMBER MATTING Aug 1984 Aug 1, 1984 July 2017 (Rev. July 20, 2017) Page 2 of 13 CDED E3-1

7 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 109S31 SUBSTITUTION OF PRECAST CONCRETE BOX CULVERTS FOR CAST- IN-PLACE CONCRETE BOX CULVERTS - Submission and Design Requirements, Aggregate, Construction and Payment of Precast Box Culvert Alternative 110S03 AMENDMENT TO OPSS 1002, APRIL Fine Aggregate and Aggregate Processing, Handling, and Stockpiling 110F10 USE OF AIR COOLED IRON BLAST FURNACE SLAG AS GRANULAR MATERIAL - Requirements for Use of Air Cooled Iron Blast Furnace Slag as Granular Material In Road Construction 110S12 AMENDMENT TO OPSS 1003, APRIL Material Specification for Aggregates - Hot Mix Asphalt (Deletes and Replaces OPSS 1003 In Its Entirety) 110F14 INFORMATION TO BIDDERS REGARDING AGGREGATE SOURCES - General 110S16 AMENDMENT TO OPSS 1004, NOVEMBER Quality Assurance Sampling, and Physical Property and Gradation Requirements for Granular Sheeting 111F06 AMENDMENT TO OPSS 1151, NOVEMBER Mix Design Criteria and Asphalt Cement Anti Stripping Treatment 111F09 AMENDMENT TO OPSS 1101, NOVEMBER Additional Test Results and Samples for Performance Graded Asphalt Cement (PGAC) 111S12 AMENDMENT TO OPSS 1103, NOVEMBER Material Specification for Emulsified Asphalt (Deletes and Replaces OPSS 1103 In Its Entirety) 112S07 AMENDMENT TO OPSS 1212, NOVEMBER Material Specification for Hot-Poured Rubberized Asphalt Joint/Crack Sealant Compound (Deletes and Replaces OPSS 1212 In Its Entirety) Jul 2011 Jul 21, 2011 Apr 2015 Apr 23, 2015 Sep 2001 Sep 20, 2001 Feb 2017 Mar 2, 2017 Jun 2012 Jul 5, 2012 May 2017 Jun 8, 2017 Mar 2017 Mar 2, 2017 Jun 2017 Jun 8, 2017 Jul 2017 Jul 13, 2017 Feb 2008 Feb 14, S03 AMENDMENT TO OPSS 1301, SEPTEMBER Cementing Materials Dec 2004 Jan 19, S05 AMENDMENT TO OPSS 1359, MAY Unshrinkable Backfill Dec 2006 Jan 25, S09 AMENDMENT TO OPSS 1352, NOVEMBER Steel Reinforcement Feb 2013 Mar 7, S06 AMENDMENT TO OPSS 1440, NOVEMBER Material Specification for Steel Reinforcement for Concrete (Deletes and Replaces OPSS 1440 In Its Entirety) 118S03 AMENDMENT TO OPSS 1821, MAY Air Void System Parameters, Salt Scaling and Concrete Cover Measurements of Precast Hardened Concrete 124S01 AMENDMENT TO OPSS 2471, NOVEMBER Coating Inspectors and Inspection by the Owner 168F10 168F14 168S20 Jun 2017 Jul 13, 2017 Feb 2017 Mar 2, 2017 Jul 2017 Jul 13, 2017 ATMS OPERATIONS - Interference With ATMS Operations Sep 2007 Jan 24, 2008 QUALITY CONTROL, TESTING AND DOCUMENTATION FOR ATMS WORK PROTECTION OF EXISTING SYSTEM - Accidental Damage to Existing ATMS Plant Mar 2012 Mar 15, 2012 Sep 2007 Oct 15, 2010 July 2017 (Rev. July 20, 2017) Page 3 of 13 CDED E3-1

8 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 168F31 168F32 INCENTIVE/DISINCENTIVE FOR REINSTATEMENT OF LOOP DETECTORS NTCIP FOR VARIABLE MESSAGE SIGNS - Requirements for Delivery, Installation, Documentation and Testing of (NTCIP) for (PVMS) and (VMS) Controllers Feb 2014 Mar 27, 2014 Jul 2009 Jul 23, F03 PLACING HOT MIX ASPHALT BEFORE SEASONAL SHUTDOWN May 2016 Jun 9, F06 STOCKPILING OF MATERIALS FOR FUTURE USE BY THE MINISTRY Jul 2010 Jul 22, F12 ENVIRONMENTALLY SENSITIVE AREAS Nov 2014 Nov 6, S18 FENCING OF THE CONSTRUCTION AREA Jun 1992 Sep 2, S24 SUPPLY OF TRUCKS Aug 1984 Aug 1, F31 ENVIRONMENTAL EXEMPTIONS AND PERMITS Apr 2016 Apr 28, F33 CONSTRUCTION NOISE CONSTRAINTS - Noise Sensitive Areas - Requirements for Control of Construction Noise Produced by the Contractor's Operations 199S38 ADMINISTRATION OF AGGREGATE SOURCES INCLUDING EARTH BORROW AND ROCK SUPPLY SOURCES AND HIGHWAY RIGHT-OF- WAY AGGREGATE PRODUCTION - Permits and Approvals for Pit and Quarry Operations, Haul Road Maintenance and Repair, and Surplus Crushed Granular Materials 199F43 OTHER CONTRACTORS WITHIN OR ADJACENT TO THE LIMITS OF THE CONTRACT Jun 2013 Jun 20, 2013 Mar 2017 Jun 8, 2017 Jun 2000 Jun 21, S44 TRAFFIC CONTROL AT INTERSECTIONS Jan 2001 Jan 10, S48 QUALITY VERIFICATION ENGINEER SERVICES Feb 2017 Mar 2, S53 PERFORMANCE REQUIREMENT-QUALITY PROCESSES - Performance Requirements for Quality Processes 199S54 PARTICIPATION IN THE ANNUAL LABORATORY CORRELATION PROGRAM - Annual Laboratory Correlation Program Feb 2012 Apr 26, 2012 May 2004 May 26, S55 RECORD DRAWINGS FOR STRUCTURES AND FOUNDATIONS May 2004 May 26, S56 CONTROL OF EMISSIONS DURING STRUCTURAL WORK - Requirements for Control of Emissions Generated from Work on Structures 199F57 GENERAL REQUIREMENTS OF SAMPLES FOR QUALITY ASSURANCE, REFEREE AND OTHER TESTING BY THE OWNER OR THE OWNER'S AGENT - Requirements for Handling, Identification, and Delivery of Samples to a Laboratory for Quality Assurance, Referee and Other Testing Sep 2005 Nov 17, 2005 Feb 2017 Mar 2, F59 NATIONAL ENERGY BOARD (NEB) REGULATED PIPELINES Feb 2015 Feb 26, S60 INCENTIVE FOR SUPPLY OF CANADIAN STEEL - Requirements for an Incentive Payment for Supply of Canadian Steel Oct 2009 Oct 29, F61 ADDITIONAL DOCUMENTS AVAILABLE DURING ADVERTISING Dec 2016 Dec 15, F63 NAVIGABLE WATERS PROTECTION Mar 2012 Apr 26, S64 GENERAL REQUIREMENTS FOR REFEREE TESTING Jul 2016 Jul 21, 2016 July 2017 (Rev. July 20, 2017) Page 4 of 13 CDED E3-1

9 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 199S65 CONTRACT DOCUMENTS AND NATIVE FORMAT ELECTRONIC INFORMATION 201F01 CLEARING - Item No., CLOSE CUT CLEARING - Item No. - Amendment to OPSS 201, November Salvage of Trees 201F02 CLEARING - Item No., CLOSE CUT CLEARING - Item No. - Amendment to OPSS 201, November Marketable Timber from Crown Lands 206F04 ROCK EXCAVATION, GRADING - Item No. - Amendment to OPSS 206, November Bulking Factor for Shale 206F06 EARTH EXCAVATION, GRADING - Item No. - Amendment to OPSS 206, November F01 RENTAL OF SWAMP EXCAVATION EQUIPMENT, DRAGLINE - Item No., (Same), HYDRAULIC BACKHOE - Item No., GEOTEXTILE FOR SWAMP TREATMENT - Item No. Amendment to OPSS 209, November F01 EARTH BORROW - Item No. - Amendment to OPSS 212, November Fly Ash Material Dec 2016 Dec 15, 2016 May 2013 Jun 20, 2013 May 2013 Jun 20, 2013 Dec 2014 Jan 8, 2015 Dec 2014 Jan 8, 2015 Dec 2014 Jan 8, 2015 Jan 2014 Mar 27, S01 WICK DRAINS - Item No. - Amendment to OPSS 220, November 2014 Dec 2016 Dec 15, F01 RENTAL OF MOTOR GRADER (Various) - Item No., RENTAL OF BACKHOE (VARIOUS) - Item No. - Use of Rental Equipment 299F02 DRILL AND BLAST ROCK IN DITCHES - Item No. - Construction Specification for Drilling and Blasting Rock in Ditches 299F11 EARTH DITCH CLEANOUT Item No., ROCK DITCH CLEANOUT Item No. Construction Specification for Ditch Cleanout 304F04 BINDER (TYPE) - Item No., CLASS 1, 2, 4, 6 AGGREGATE - Item No., CLASS 1, 2, 4, 6 AGGREGATE, FROM STOCKPILE - Item No. - Amendment to OPSS 304, November Application of Binder, Binder Sampling, Determination of Binder and Aggregate Application Rates, Quality Assurance and Price Adjustments 305S03 GRANULAR SEALING - Item No. - Amendment to OPSS 305, November F02 TACK COAT - Item No. - Amendment to OPSS 308, April Painting Material, Application Options, and Samples for Testing 331F02 FULL-DEPTH RECLAMATION WITH EXPANDED ASPHALT STABILIZATION Item No. - Amendment to OPSS 331, November Design Rate of Expanded Asphalt 332F03 HOT IN-PLACE RECYCLED MIX - Item No. - Amendment to OPSS 332, November Design Requirements and Preparation of Existing Pavement 333S04 COLD IN-PLACE RECYCLED MIX Item No. - Amendment to OPSS 333, November Compaction Measurement Using Nuclear Moisture and Density Gauge 335S04 COLD IN-PLACE RECYCLED EXPANDED ASPHALT MIX Item No. - Amendment to OPSS 335, November Compaction Measurement Using Nuclear Moisture and Density Gauge May 2002 May 29, 2002 Apr 2014 May 8, 2014 Sep 2011 Sep 29, 2011 Feb 2017 Mar 2, 2017 Mar 2017 Mar 2, 2017 Feb 2017 Mar 2, 2017 Nov 2015 Dec 17, 2015 Nov 2016 Jan 12, 2017 Jun 2016 Jul 21, 2016 Jun 2016 Jul 21, 2016 July 2017 (Rev. July 20, 2017) Page 5 of 13 CDED E3-1

10 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 336F01 MICRO-SURFACING -TYPE (VARIOUS) - Item No. - Amendment to OPSS 336, November F01 SLURRY SEAL TYPE (VARIOUS) - Item No. - Amendment to OPSS 337, November S01 SEALING CRACKS IN ASPHALT PAVEMENT - Item No., ROUTING AND (Same) - Item No. - Delete and Replace Construction Specification for Routing and Sealing Cracks in Asphalt Pavement (Deletes and Replaces OPSS 341 In Its Entirety) 351S01 TACTILE WALKING SURFACE INDICATORS FOR CONCRETE SIDEWALK RAMPS - Item No. - Amendment to OPSS 351, November S02 CONCRETE SIDEWALK - Item No. - Amendment to OPSS 351, November Granular Material Placed Below Sidewalk 353S02 CONCRETE CURB AND GUTTER - Item No. - Amendment to OPSS 353, September F01 FULL DEPTH CRACK REPAIRS - Item No. - Requirements for Full Depth Crack Repairs in Asphaltic Concrete Pavements 399F02 TEMPORARY HOT MIX PAVEMENT - Item No. - Construction Specification for Temporary Hot Mix Pavement 399S09 RECLAIM ASPHALT PAVEMENT - PARTIAL DEPTH - Item No. - Requirements for Reclaiming Existing Asphalt Pavement to a Partial Depth and Stockpiling the Processed Material for Reuse 399S10 RECLAIM ASPHALT PAVEMENT - FULL DEPTH - Item No. - Requirements for Reclaiming Existing Asphalt Pavement and Asphalt Curb and Gutter to Their Full Depth, and Stockpiling the Material for Reuse 399S43 FULL DEPTH CONCRETE REPAIR - Item No., FAST TRACK (Same) - Item No., PARTIAL DEPTH CONCRETE REPAIR - Item No., FAST TRACK (Same) - Item No. - Construction Specification for Partial Depth, Full Depth, and Fast Track, Repairs to Concrete Pavement and Concrete Base (Deletes and Replaces OPSS 360, 362, and 364) 407S01 BREAKING INTO MANHOLES, CATCHBASINS, DITCH INLETS, CULVERTS AND SEWERS - Item No. - Amendment to MTC Form 407, March Pipe Subdrain Outlet to Existing Structure 407S02 ROCK EXCAVATION FOR SEWERS, MANHOLES, CATCHBASINS AND DITCH INLETS - Item No. - Amendment to MTC Form 407, March S03 CATCH BASIN COLLAR - Item No. - Amendment to MTC Form 407, March S06 (SIZE) MANHOLES CATCH BASINS AND DITCH INLETS - Item No., ADJUSTING AND REBUILDING MHs, CBs AND DIs - Item No. - Amendment to MTC Form 407, March Aggregate Requirements, Lift Rings, Adjustment Units and Resilient Connectors 415S01 TUNNEL - Item No. - Amendment to OPSS 415, February Interceptor Drains and Service Connections 416S01 JACKING AND BORING - Item No. - Amendment to OPSS 416, February Interceptor Drains and Service Connections May 2016 Jun 9, 2016 Nov 2013 Dec 5, 2013 Feb 2017 Mar 2, 2017 Oct 2016 Dec 15, 2016 Jan 2016 Jan 28, 2016 Jul 2007 Aug 30, 2007 Dec 2014 Dec 18, 2014 Jan 2017 Mar 2, 2017 Jun 2006 Jul 27, 2006 May 2010 May 20, 2010 Feb 2013 Mar 7, 2013 Feb 1988 May 1, 1988 Aug 2007 Sep 20, 2007 Jul 1996 Aug 16, 1996 Apr 2014 Jun 12, 2014 Mar 2012 Apr 26, 2012 Mar 2012 Apr 26, 2012 July 2017 (Rev. July 20, 2017) Page 6 of 13 CDED E3-1

11 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 422S01 PRECAST CONCRETE BOX CULVERT - Item No. - Amendment to OPSS 422, April S02 CLEAN OUT CATCHBASINS, MAINTENANCE HOLES AND DITCH INLETS - Item No. - Management of Highway Storm Sewer Catchbasin Cleanout Material - No Receiving Site Provided 499S03 WELD AND RELEASE MAINTENANCE HOLE AND CATCH BASIN FRAMES AND GRATES - Item No. 517F01 DEWATERING SYSTEM - Item No., TEMPORARY FLOW PASSAGE SYSTEM - Item No. - Amendment to OPSS 517, November Design Storm Return Period and Preconstruction Survey Distance 599S22 RETAINED SOIL SYSTEM (VARIOUS) - Item No.; BACKFILL FOR RSS (VARIOUS) - Item No. - Requirements for Design and Construction of RSS Walls and Steep Slopes 599S23 RETAINED SOIL SYSTEM (VARIOUS) - Item No. - Requirements for Materials, QC and QA Testing and Acceptance Criteria for Precast Concrete Facing Elements Including Panels 601S01 (ELEC) 610F01 (ELEC) 611F01 (ELEC) 614F01 (ELEC) 615S05 (ELEC) 617F01 (ELEC) 617F03 (ELEC) 622F03 (ELEC) 623F03 (ELEC) 623F04 (ELEC) MAINTENANCE AND OPERATION FOR TEMPORARY TRAFFIC SIGNAL SYSTEM WORK - Item No. - Requirements for Maintenance and Operation of Temporary Traffic Signal System REMOVAL OF ELECTRICAL EQUIPMENT - Item No. - Shipping of Salvaged Electrical Equipment and Materials UNDERPASS LUMINAIRES - Item No., (Same) (TEMPORARY) - Item No., REPLACE (Same) - Item No. - Amendment to OPSS 611, November 2013 DISTRIBUTION ASSEMBLIES - Item No., (Same) (TEMPORARY) - Item No., SUPPLY CONTROL CABINET ASSEMBLIES - Item No., (Same) (TEMPORARY) - Item No. - Amendment to OPSS 614, November Listing of Descriptions for Distribution and Supply Control Cabinet Assemblies, and Supply of Arc Flash and Shock Hazard Warning Labels BREAKAWAY BASE ANTI-THEFT DEVICE - Item No. - Amendment to OPSS 615, April 2017 LIGHTING LUMINAIRES (VARIOUS) - Item No., (Same) (TEMPORARY) - Item No. - Amendment to OPSS 617, November 2013 (VARIOUS) LED LIGHTING LUMINAIRES - Item No. - Amendment to OPSS 617, November 2013 TRAFFIC SIGNAL CONTROLLERS - Item No., TRAFFIC SIGNAL CONTROLLERS (TEMPORARY) - Item No. - Amendment to OPSS 622, April 2017 for Traffic Signal Controller Programming and Timing ACCESSIBLE PEDESTRIAN SIGNALS - Item No., ACCESSIBLE PEDESTRIAN SIGNALS (TEMPORARY) - Item No. - Amendment to OPSS 623, April 2017 for Listing of Product Descriptions and Verbal Announcements for Accessible Pedestrian Signals NON-INTRUSIVE DETECTION SYSTEM - Item No., NON-INTRUSIVE DETECTION SYSTEM (TEMPORARY) - Item No. - Amendment to OPSS 623, April 2017 for Listing of Non-Intrusive Detection System Equipment Jul 2011 Jul 21, 2011 Mar 2012 Apr 26, 2012 Jan 2000 Feb 2, 2000 Jul 2017 Jul 13, 2017 Feb 2016 Mar 03, 2016 Feb 2017 Mar 2, 2017 Nov 2014 Dec 18, 2014 Nov 2016 Jan 12, 2017 Feb 2014 Mar 27, 2014 Apr 2017 Jun 8, 2017 May 2017 Jun 8, 2017 Feb 2014 Mar 27, 2014 Feb 2014 Mar 27, 2014 May 2017 Jun 8, 2017 May 2017 Jun 8, 2017 May 2017 Jun 8, 2017 July 2017 (Rev. July 20, 2017) Page 7 of 13 CDED E3-1

12 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 630F02 (ELEC) 631S02 (ELEC) 681F15 681F17 681F19 681F25 681F32 681F34 682S01 682S07 682S08 682S09 682S12 682S13 682S14 682S15 682S16 682S17 (Various m) SECTIONAL STEEL HIGH MAST LIGHTING POLES AND EQUIPMENT - Item No. - Amendment to OPSS 630, November 2016 CONCRETE FOOTINGS FOR HIGH MAST LIGHTING POLES - Item No. - Amendment to OPSS 631, November 2015 TRAINING FOR ATMS WORK - Item No. - Requirements for Training Seminars to be Provided by the Contractor SPARE COMPONENTS FOR ATMS WORK - Item No. - Requirements for Supply of Additional Quantities of Tender Items SYSTEM INTEGRATION TESTING FOR ATMS WORK - Item No. - Requirements for System Integration Testing (SIT) of all ATMS Subsystems. MAINTENANCE AND WARRANTY FOR ATMS WORK - Item No. - Requirements for Maintenance and Warranty for all ATMS Components Supplied, Installed, Replaced or Modified GROUND DEPLOYMENT OF PVMS - Item No., FIXED SUPPORT DEPLOYMENT OF PVMS - Item No. - Requirements for Deployment of Portable Variable Message Signs (PVMS) MAINTENANCE AND WARRANTY FOR PVMS - Item No. - Requirements for Maintenance and Warranty of Portable Variable Message Signs (PVMS) and Associated Subsystem Components ATMS FIELD EQUIPMENT CABINET MAINTENANCE SITES - Item No. - Requirements for Construction of ATMS Field Equipment Cabinet Maintenance Sites FLEXIBLE DUCTS BY SUBSURFACE INSTALLATION Item No., RIGID DUCTS, DIRECT BURIED - Item No., (Same) (TEMPORARY) Item No. - Amendment to OPSS 603, November 2015 SURFACE MOUNTED DUCT SYSTEMS - Item No., (Same) (TEMPORARY) - Item No. - Amendment to OPSS 603, November 2015 EXTRA LOW VOLTAGE CABLES (VARIOUS) - Item No., SAWCUT SLOT FOR EXTRA LOW VOLTAGE CABLES - Item No. - Amendment to OPSS 604, November 2013 POWER SUPPLY CABINETS - Item No. - Requirements for Installation of Power Supply Cabinets CONCRETE POLES, DIRECT BURIED IN EARTH - Item No. - Amendment to OPSS 615, November 2008 Nov 2016 Jan 12, 2017 Feb 2016 Mar 03, 2016 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Jun 2017 Jun 8, 2017 Sep 2007 Jan 24, 2008 Mar 2012 Apr 26, 2012 Apr 2016 Apr 28, 2016 Feb 2016 Mar 03, 2016 Feb 2016 Mar 03, 2016 Feb 2014 Mar 27, 2014 Sep 2010 Oct 14, 2010 Feb 2009 Mar 12, 2009 CONCRETE PADS - Item No. - Amendment to OPSS 616, November 2012 Feb 2013 Mar 7, 2013 BASE MOUNTED COMMUNICATION PEDESTALS - Item No. - Requirements for Installation of Base Mounted Communications Pedestal on a Concrete Footing CONTROLLER CABINETS - Item No. - Amendment to OPSS 622, April 2017 CONTROLLERS - Item No. - Requirements for Installation and Testing of Advanced Traffic Controllers (ATCs) Sep 2007 Jan 24, 2008 Jun 2017 Jun 8, 2017 Jul 2012 Sep 13, 2012 July 2017 (Rev. July 20, 2017) Page 8 of 13 CDED E3-1

13 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 682S18 682S19 682S20 682F22 682S23 682S25 682S26 682S27 682S28 682S30 682F34 683S01 683S02 683S03 683S04 683S07 683S09 683S10 LOOP VEHICLE DETECTOR SENSOR UNITS - Item No. - Requirements for Installation and Testing of Loop Vehicle Detector Sensor Units ATMS LOOP DETECTORS - Item No., (Same) (TEMPORARY) - Item No. - Amendment to OPSS 623, April 2017 TEST EXISTING LOOP DETECTORS - Item No. - Requirements for Locating and Testing of Existing Loop Detectors Installed Under Previous Contracts REMOVAL OF ADVANCED TRAFFIC MANAGEMENT SYSTEM EQUIPMENT - Item No. - Amendment to OPSS 610, November 2016 INNER CHAMBERS - Item No. - Requirements for Installation of Inner Chambers Within Rigid Ducts CONCRETE FOOTINGS IN EARTH - Item No. - Amendment to OPSS 616, November 2012 NON-INTRUSIVE TRAFFIC SENSORS (Microwave) - Item No. - Requirements for Installation, Calibration, Integration and Testing of Non- Intrusive Traffic Sensor (NITS) Units CONTROLLER CABINETS, POLE MOUNTED - Item No. - Requirements for Installation of Pole Mounted Controller Cabinets UNINTERRUPTIBLE POWER SUPPLY UNITS - Item No. - Requirements for Installation and Testing of Uninterruptible Power Supply Units (UPS) CONCRETE POLES, DIRECT BURIED IN EARTH WITH CAMERA RAISING AND LOWERING SYSTEM - Item No., (Same) IN ROCK - Item No. - Amendment to OPSS 615, November 2008 EXTERNAL UNINTERRUPTIBLE POWER SUPPLY UNITS - Item No. - Requirements for Installation and Testing of Integrated External Uninterruptible Power Supply Units FIBRE OPTIC COMMUNICATION CABLES, IN DUCTS - Item No., (Same) (TEMPORARY) - Item No., FIBRE OPTIC COMMUNICATION CABLES, AERIAL ON MESSENGER CABLE - Item No., (Same) (TEMPORARY) - Item No. - Requirements for Installation, Splicing and Testing of Fibre Optic Communication Cables to be Placed in Ducts SPLICE ENCLOSURES FOR FIBRE OPTIC CABLES - Item No. - Requirements for Installation of Splice Enclosures for Fibre Optic Cables DATA INTERFACE CABLES - Item No. - Requirements for Installation and Testing of Connectorized Data Cables for Interfaces VIDEO TRANSMITTERS AND RECEIVERS - Item No. - Requirements for Installation and Testing of the Video Transmitters and Receivers VIDEO SYSTEM LINE UP AND TEST - Item No. - Requirements for System Line Up and Test (SLAT) of All Existing Analog Video Links FIBRE OPTIC MODEMS - Item No. - Requirements for Installation and Testing of Fibre Optic Modems (FOM) PORT SHARING DEVICES - Item No. - Requirements for Installation and Testing of Port Sharing Device (PSD) Sep 2007 Jan 24, 2008 May 2017 Jun 8, 2017 Sep 2007 Jan 24, 2008 Nov 2016 Jan 12, 2017 Sep 2007 Jan 24, 2008 Feb 2013 Mar 7, 2013 Jun 2017 Jun 8, 2017 Jun 2017 Jun 8, 2017 Nov 2013 Dec 5, 2013 Jul 2009 Jul 23, 2009 Jun 2017 Jun 8, 2017 Feb 2013 Mar 7, 2013 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 July 2017 (Rev. July 20, 2017) Page 9 of 13 CDED E3-1

14 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 683S11 683F18 683S19 683S22 683S23 683S24 683S25 683S26 683S27 684S01 684S07 684S10 685S01 685S07 687S01 DATA SYSTEM LINEUP AND TEST - Item No. - Requirements for Line Up and Test of Data System FIBRE OPTIC MODEMS - Item No. - Requirements for Installation and Testing of Low Range Fibre Optic Modems (LFOM), High Range Fibre Optic Modems (HFOM), Fibre Optic Taps (FOT), and Fibre Optic Splitters (FOS) DROP / INSERT NODES - Item No., CHANNEL PORTS - Item No. - Requirements for Installation and Testing of Field Drop and Insert Nodes (FDINs), Central Drop and Insert Nodes (CDINs), Data Channel Ports (DCPs), LAN Channel Ports (LCPs) and Fibre Optic Ethernet Hubs (FOEHs) WIRELESS ETHERNET BRIDGES - Item No. - Requirements for Installation and Testing of Wireless Ethernet Bridges DIGITAL VIDEO ENCODERS AND DECODERS - Item No. - Requirements for Installation and Testing of Digital Video Encoders and Digital Video Decoders PORT SERVERS - Item No. - Requirements for Installation and Testing of Port Servers ETHERNET SWITCHES - Item No. - Requirements for Installation and Testing of Ethernet Switches FIBRE OPTIC ETHERNET MODEM - Item No. - Requirements for Installation and Testing of Fibre Optic Ethernet Modems GATEWAY ROUTERS - Item No. - Requirements for the Installation of Gateway Routers OUTDOOR CLOSED CIRCUIT TELEVISION CAMERAS - Item No. - Requirements for Installation and Testing of CCTV Camera and Lens, Environmental Enclosure, Video Interface Cable and Camera and Accessory Power Cable and Ground Wire CLOSED CIRCUIT TELEVISION VIDEO MONITORS - Requirements for Supply, Installation and Testing of CCTV Monitors DOME CAMERA SYSTEM - Item No. - Requirements for Installation and Testing of Dome Camera System VARIABLE MESSAGE SIGNS - Item No. - Requirements for Design, Installation and Testing of Colour Full Matrix Variable Message Signs (VMS), VMS controllers, and All Associated Equipment FIXED SUPPORT MOUNTABLE VARIABLE MESSAGE SIGNS - Item No. - Requirements for Delivery, Installation, Documentation and Testing of Variable Message Signs (VMS) to be Mounted on a Support Structure RACK ASSEMBLIES - Item No. - Requirements for Installation of Rack Assemblies Including Power Distribution Equipment 706F04 PVMS (TEMPORARY) - Item No., PVMS, RELOCATION - Item No. - Amendment to OPSS 706, November Designation of Modem and Message Details for PVMS 708F01 PORTABLE TEMPORARY TRAFFIC SIGNALS - Item No. - Amendment to OPSS 708, November Traffic Signal Timing Sep 2007 Jan 24, 2008 Apr 2005 Apr 6, 2005 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Sep 2010 Oct 14, 2010 Sep 2007 Jan 24, 2008 Jun 2017 Jun 8, 2017 Sep 2007 Jan 24, 2008 Sep 2007 Jan 24, 2008 Feb 2014 Mar 27, 2014 Feb 2016 Mar 03, 2016 Feb 2016 Mar 03, 2016 Sep 2007 Jan 24, 2008 Nov 2016 Mar 2, 2017 Nov 2016 Jan 12, 2017 July 2017 (Rev. July 20, 2017) Page 10 of 13 CDED E3-1

15 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 710S01 PAVEMENT MARKING - Item No., (Same), DURABLE - Item No., (Same), TEMPORARY - Item No., (Same), TEMPORARY - REMOVABLE - Item No. - Amendment to OPSS 710, November S02 PAVEMENT MARKING - Item No., (Same), TEMPORARY - Item No. - Amendment to OPSS 710, November Double Application of Organic Solvent Based Traffic Paint 710S03 PAVEMENT MARKING OBLITERATING BY ABRASIVE BLASTING - Item No. - Amendment to OPSS 710, November Removing and Obliterating Pavement Markings 710S04 PAVEMENT MARKING OBLITERATING - BY GRINDING - Item No. - Amendment to OPSS 710, November Removing and Obliterating Pavement Markings 710S05 PAVEMENT MARKING OBLITERATING - BY BLACK LINE MASK Item No. - Amendment to OPSS 710, November Removing and Obliterating Pavement Markings 710S06 PAVEMENT MARKERS, RECESSED - Item No. - Amendment to OPSS 710, November Marker Requirements for Recessed Pavement Markers 710F07 PAVEMENT MARKING - Item No., (Same), DURABLE - Item No. - Amendment to OPSS 710, November F08 PAVEMENT MARKING, TEMPORARY - Item No. - Amendment to OPSS 710, November F09 PAVEMENT MARKING, TEMPORARY, FIELD REACTED POLYMERIC - FLUORESCENT ORANGE Item No. - Amendment to OPSS 710, November F10 PAVEMENT MARKING, TEMPORARY, PAINT - FLUORESCENT ORANGE - Item No. - Amendment to OPSS 710, November S11 PAVEMENT MARKING, TEMPORARY REMOVABLE - FLUORESCENT ORANGE - Item No. - Amendment to OPSS 710, November S05 SINGLE RAIL STEEL BEAM GUIDE RAIL - Item No. - Amendment to OPSS 721, November Type M SBGR Mounting Heights 721S06 SINGLE RAIL STEEL BEAM GUIDE RAIL, BASE PLATED FOR SHALLOW CULVERTS - Item No. - Amendment to OPSS 721, November S01 ENERGY ATTENUATOR TEMPORARY, REDUCED EXPOSURE - Item No., ENERGY ATTENUATOR RELOCATION, REDUCED EXPOSURE - Item No. - Amendment to OPSS 723, November S02 ENERGY ATTENUATOR - TEMPORARY, NARROW - Item No. - Amendment to OPSS 723, November S03 STEEL BEAM ENERGY ATTENUATING TERMINAL SYSTEM - Item No. - Amendment to OPSS 732, April S01 CONCRETE BARRIER - Item No., ASYMMETRIC (Same) - Item No., TALL WALL BARRIER - Item No., ASYMMETRIC (Same) - Item No. - Amendment to OPSS 740, November 2010 Sep 2011 Sep 29, 2011 Sep 2011 Sep 29, 2011 Sep 2011 Sep 29, 2011 Sep 2011 Sep 29, 2011 Sep 2011 Sep 29, 2011 Sep 2011 Sep 29, 2011 Sep 2011 Sep 29, 2011 Sep 2011 Sep 29, 2011 Feb 2012 Mar 15, 2012 Feb 2012 Mar 15, 2012 Feb 2012 Mar 15, 2012 Apr 2016 Apr 28, 2016 Jul 2016 Jul 21, 2016 Aug 2016 Sep 1, 2016 Feb 2017 Mar 2, 2017 Sep 2016 Sep 1, 2016 Sep 2011 Sep 29, 2011 July 2017 (Rev. July 20, 2017) Page 11 of 13 CDED E3-1

16 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 741S01 TEMPORARY CONCRETE BARRIER, REDUCED DEFLECTION - Item No.; (Same), RELOCATION - Item No. - Amendment to OPSS 741, November S02 STEEL BEAM ENERGY ATTENUATING TERMINAL SYSTEM - Item No. - Amendment to OPSS 732, April F01 height NOISE BARRIER SYSTEM Item No., height NOISE BARRIER SYSTEM INCLUDING PRECAST NOISE/TRAFFIC BARRIER - Item No., height NOISE BARRIER SYSTEM ON STRUCTURES Item No., NOISE BARRIER ACCESS Item No. - Amendment to OPSS 760, November S03 TEMPORARY TRANSITION RAIL - Item No. - Construction Specification for Temporary Transition Rail 799S04 PERMANENT REACT Item No. - Construction Specification for Permanent REACT S05 CIAS; STEAL BEAM TERMINAL; SBEAT SYSTEM; ENERGY ATTENUATOR - (VARIOUS); PERMANENT REACT 350; TCB RESTRAINT SYSTEM - (VARIOUS); HIGH TENSION THREE CABLE GUIDE RAIL (Various); HIGH TENSION CABLE GUIDE RAIL TERMINAL SYSTEM; INTERMEDIATE SIGNS (VARIOUS) - Item No. - Certification of Safety Items 799S08 BOLLARDS - Item No. - Construction Specification for the Installation of Bollards 799S12 RAMP CLOSURE GATES - Item No., CONCRETE IN RAMP CLOSURE GATE SUPPORT FOOTINGS - Item No. - Construction Specification for Ramp Closure Gates 799S15 HIGH TENSION THREE CABLE GUIDE RAIL SHOULDER INSTALLATION - Item No., HIGH TENSION THREE CABLE GUIDE RAIL SLOPE INSTALLATION - Item No., HIGH TENSION CABLE GUIDE RAIL TERMINAL SYSTEM - Item No. - Requirements for the Installation of High Tension Cable Guide Rail and Terminal Systems 799S16 STEEL BEAM TERMINAL SYSTEM - Item No. - Requirements for the Installation of Steel Beam Terminal (SBT) System 799S17 INTERMEDIATE SIGNS, (Various) - Item No. - Construction Specification for Permanent Intermediate Signs and Support Systems 805F01 (VARIOUS) BARRIERS Item No., (VARIOUS) CHECK DAMS - Item No., (VARIOUS) TRAPS Item No., TURBIDITY CURTAINS Item No., COFFERDAMS Item No., FIBRE ROLL GRADE BREAKS - Item No., SLOPE DRAINS - Item No., DIVERSION DITCHES - Item No., FILTER BAGS - Item No., - Amendment to OPSS 805, November S01 MANAGEMENT AND DISPOSAL OF MATERIALS CONTAINING ASBESTOS - Item No. - Requirements for Management and Disposal of Materials That Contain or May Contain Asbestos 911F10 COATING EXISTING STRUCTURAL STEEL - Item No., COATING NEW STRUCTURAL STEEL - Item No., COATING STEEL RAILING SYSTEM(S) - Item No. - Item No. - Supplemental Instructions to Bidders and Amendment to OPSS 911, November 2014 Jul 2015 Aug 27, 2015 Aug 2016 Sep 1, 2016 Jun 2015 Oct 22, 2015 Sep 2011 Sep 29, 2011 Feb 2013 Mar 7, 2013 Feb 2017 Mar 2, 2017 Mar 2012 Mar 15, 2012 May 2013 Jun 20, 2013 Dec 2016 Dec 15, 2016 Dec 2016 Dec 15, 2016 Feb 2017 Mar 2, 2017 Dec 2015 Jan 28, 2016 Mar 2015 Apr 23, 2015 May 2016 Jun 9, 2016 July 2017 (Rev. July 20, 2017) Page 12 of 13 CDED E3-1

17 CHAPTER E SPECIAL PROVISIONS LIST OF ACTIVE SSPs S.P. # Title Issue Date Imp. Date 914F02 BRIDGE DECK WATERPROOFING - Item No., DECK SURFACE PREPARATION - Item No. - Amendment to OPSS 914, November S03 FORM AND FILL GROOVES - Item No. - Amendment to OPSS 914, November F01 BEARINGS - Item No. - Amendment to OPSS 922, November Requirements for Elastomeric Bearings 928F01 CONCRETE REMOVAL - PARTIAL DEPTH - TYPE (A, B, C) - Item No. - Half Cell Survey 931S01 NORMAL SHOTCRETE - Item No., SILICA FUME SHOTCRETE - Item No. - Construction Specification for Structure Rehabilitation - Shotcrete (Deletes and Replaces OPSS 931 In Its Entirety) 999S02 GLASS FIBRE REINFORCING POLYMER REINFORCING BAR - Item No. - Construction Specification For Glass Fibre Reinforcing Polymer Reinforcing Bar 999F29 DOWELS INTO CONCRETE - Item No. - Construction Specification for the Installation of Metallic Dowels Into Concrete 999S30 JACKING OF SUPERSTRUCTURE Item No. - Construction Specification for the Jacking of Bridge Superstructure 999F31 PRECAST CONCRETE BRIDGE ELEMENTS, FABRICATION - Item No., (Same), DELIVERY - Item No., (Same), INSTALLATION - Item. No. - Construction Specification for Non-Prestressed Precast Concrete Bridge Elements Dec 2014 Dec 18, 2014 Mar 2016 Mar 03, 2016 Nov 2016 Jan 12, 2017 Aug 1995 Sep 1, 1995 Feb 2017 Mar 2, 2017 Jun 2017 Jun 8, 2017 May 2016 Jun 9, 2016 Feb 2016 Mar 03, 2016 Feb 2017 Mar 2, 2017 Note: The above table lists all active SSPs currently implemented for use in CPS. Those identified as (ELEC) or are published in Volume 3, Electrical CDED Manual and Volume 4, Electrical CDED ATMS Manual, accordingly. Users should refer to the respective manuals for further information regarding the use of those SPs. July 2017 (Rev. July 20, 2017) Page 13 of 13 CDED E3-1

18

19 AMENDMENT TO OPSS 911, NOVEMBER Measurement of Coating Thickness Special Provision No. 109S13 July QUALITY ASSURANCE Measurement of Coating Thickness on New Structural Steel Sign Support Structures and Sectional Steel High Mast Lighting Poles Clause of OPSS 911 is deleted in its entirety and replaced with the following: The dry film thickness shall be measured by Type 2 constant probe magnetic gauges according to ASTM D 7091 and SSPC-PA 2, except that 5 separate spot measurements at representative locations of each galvanized sign support columns or legs and each sectional steel high mast lighting pole shall be taken after the application of individual coats of the paint coating system. The Contractor shall note defects on sectional steel high mast lighting poles prior to installation. All defects shall be repaired according to the Repair of Paint Coatings on Galvanized Surfaces and Repair of Hot Dip Galvanizing clauses as applicable. The coating of sectional steel high mast lighting poles is subject to inspection by the Contract Administrator. July 2017 Page 1 of 1 SSP 109S13

20

21 AMENDMENT TO OPSS 905, NOVEMBER 2014 Special Provision No. 109S17 June 2017 OPSS 905, November 2014 Construction Specification for Steel Reinforcement for Concrete is deleted in its entirety and replaced with the following: SCOPE This specification covers the requirements for the placement of all steel reinforcement and mechanical connections for concrete structures REFERENCES This specification refers to the following standards, specifications or publications: Ontario Provincial Standard Specifications, Construction OPSS 909 OPSS 910 Prestressed Concrete - Precast Members Stressing Systems for Post-Tensioning Ontario Provincial Standard Specifications, Material OPSS 1440 Steel Reinforcement for Concrete Ontario Ministry of Transportation Publications Structural Manual Laboratory Testing Manual: LS-434 Method of Test for Mechanical Connectors Used to Splice Steel Reinforcement LS-448 Method of Test for Determination of Tensile Properties of Welded Wire Reinforcement CSA Standards G (R2014) Carbon Steel Bars for Concrete Reinforcement S6-14 Canadian Highway Bridge Design Code W186-M1990 (R2012) Welding of Reinforcing Bars in Reinforced Concrete Construction ASTM International A 276 / A 276M-16a A 421 / A 421M-15 A 955 / A 955M-16a Stainless Steel Bars and Shapes Stress - Relieved Steel Wire for Prestressed Concrete Deformed and Plain Stainless Steel Bars for Concrete Reinforcement DEFINITIONS For the purpose of this specification the following definitions apply: June 2017 Page 1 of 13 SSP 109S17

22 Mechanical Connection means a joining of two reinforcing steel bars, stainless steel reinforcing bars, or posttensioning tendons by means of a mechanical connector. Post-Tensioning means a method of prestressing in which tendons are stressed after the concrete has reached a predetermined strength. Prestressing Steel means steel strand or bar that exhibits the principal attributes of high tensile strength and ductility because of its composition and method of production. Reinforcing Steel Bars means deformed steel bars made of carbon steel as defined in CSA G30.18, used for the reinforcement of concrete. Slip means the axial displacement of the reinforcing bars measured relative to the mechanical connector. Displacement is measured at a rebar stress of 5% of specified yield after the mechanical connection has been loaded to a rebar stress of 50% of specified yield and then unloaded to a bar stress of 5% of specified yield. Splice Bar means a reinforcing steel bar or stainless steel reinforcing bar that is further manufactured, other than by solely cutting threads, to be compatible with a specific mechanical connector. Stainless Steel Reinforcing Bars means deformed stainless steel bars as defined in ASTM A 955 / A 955M used for the reinforcement of concrete. Steel Reinforcement means all types of steel reinforcement for concrete including reinforcing steel bars, stainless steel reinforcing bars, splice bars, steel welded wire reinforcement, and prestressing strands and bars. Steel Welded Wire Reinforcement means a wire mesh fabricated by means of resistance welding the crossing joints, available in rolls or flat sheets. Strand means a group of wires laid helically over a central-core wire. A seven-wire strand would consist of six outer wires laid over a single wire core. Structure means any bridge, culvert, tunnel, retaining wall, wharf, dock, or guideway, or any part thereof, or other reinforced concrete component designed to carry loads, including high mast pole footings and sign support footings. Swaged means to apply circumferential pressure to a sleeve surrounding a bar to deform the sleeve sufficiently to achieve bearing between the deformed sleeve and the deformations on the bar. Ultimate Tensile Strength means the breaking load of the material per unit area established by tensile testing. Yield Strength means the stress at which the material exhibits a specified deviation of proportionality of stress and strain DESIGN AND SUBMISSION REQUIREMENTS Submission Requirements Working Drawings June 2017 Page 2 of 13 SSP 109S17

23 Steel Reinforcement Working Drawings Three sets of steel reinforcement Working Drawings shall be submitted to the Contract Administrator for information purposes only at least 7 Days prior to the commencement of placing steel reinforcement. An Engineer s seal and signature shall be affixed on the Working Drawings verifying that they are consistent with the Contract Documents. The Working Drawings shall include at least the following: quantity, bar size, grade, mark number, location, and spacing for all steel reinforcement. When a metric to imperial bar size substitution is made, the placing drawings shall include the quantity, bar size, grade, location, and spacing of both the metric and the substitute imperial bar. When bar marks are indicated on the Contract Documents and reinforcing bar lists show the same bar marks, Working Drawings are not required. A sealed and signed copy of these drawings shall be kept at the site before and during placing of steel reinforcement Steel Reinforcement Schedule Three sets of steel reinforcement schedules shall be submitted to the Contract Administrator for information purposes only at least 7 Days prior to the commencement of placing steel reinforcement. An Engineer s seal and signature shall be affixed on the Working Drawings verifying that they are consistent with the Contract Documents. The steel reinforcement schedules shall include at least: quantity, bar size, grade, reinforcing steel bars, stainless steel reinforcing bars, welded wire reinforcement, type if applicable, length, and bending dimensions. When bar marks are shown on the Working Drawings, they shall be used in the schedule. Steel reinforcement shall be detailed according to CAN/CSA-S6, and the Structural Manual. A sealed and signed copy of the steel reinforcement schedule shall be kept at the site prior to and during placement of steel reinforcement Prestressed Concrete - Precast Members Submission of proposals and shop drawings for prestressed concrete-precast members shall be according to OPSS Prestressed Concrete - Post-Tensioning Submissions for post-tensioning shall be according to OPSS Welding Details Three sets of welding details shall be submitted to the Contract Administrator for information purposes only at least 7 Days prior to the commencement of steel reinforcement welding. An Engineer s seal and signature shall be affixed on the Working Drawings verifying that they are consistent with the Contract Documents. The welding details shall include materials, procedures, bars to be welded, location, and type of welds, as well as details of tack welds. Details shall be designed to prevent notching effects in the bars. June 2017 Page 3 of 13 SSP 109S17

24 A sealed and signed copy of the welding details shall be kept at the site prior to and during welding of reinforcing Mechanical Connections Details Three sets of mechanical connection details shall be submitted to the Contract Administrator for information purposes only at least 7 Days prior to the commencement of installation of the connectors. Prior to making a submission, an Engineer s seal and signature shall be affixed on the Working Drawings verifying that they are consistent with the Contract Documents. The connections details shall contain the following information: a) The type or series identification of the connector. b) The grade and size of the reinforcement to be joined by the connector. c) A copy of the manufacturer's catalogue giving complete data on the connector material and installation procedures. d) Location of splices, including type of splice MATERIALS Steel Reinforcement Steel reinforcement shall be according to OPSS Post-Tensioning Materials Post-tensioning materials shall be according to OPSS Mechanical Connections Details Post-Tensioning Tendons When tested in an unbonded condition, mechanical connections for post-tensioning tendons shall develop at least 100% of the ultimate tensile strength of the tendons, without exceeding the anticipated set. The mechanical connection shall withstand without failure, two million cycles of stress through a range of 245 MPa for plain bars and 195 MPa for strands and ribbed bars. The upper limit of the range shall be 70% of the nominal tensile strength Reinforcing Steel Bars, Stainless Steel Reinforcing Bars The mechanical connections shall be qualified by tests made on sample splices according to the Job Control Tests clause. Mechanical connections for steel reinforcement shall develop, in tension, at least 125% of the specified yield strength of the bars to be used, in the test of the mechanical connection. June 2017 Page 4 of 13 SSP 109S17

25 The total slip of the reinforcing bars shall not exceed the following measured displacements between gauge points straddling the mechanical connector: a) For bar sizes up to and including No. 45M 0.25 mm b) For No. 55M bars 0.75 mm Splice bars shall be supplied by the manufacturer of the associated mechanical connector. Stainless steel splice bars shall be used with stainless steel reinforcing bars and shall be of a type according to OPSS Mechanical Connectors Post-Tensioning Tendons Mechanical connectors shall be supplied by the manufacturer of the prestressing system Reinforcing Steel Bars, Stainless Steel Reinforcing Bars Mechanical connectors shall be of an approved type and design and may be the form saver type, the filled sleeve type, the sleeve swaged coupler type, the threaded coupler type, the hot rolled thread bar coupler type, or the forged bar coupler type. Stainless steel mechanical connectors shall be used with stainless steel reinforcing bars and shall be of a type according to OPSS Associated Hardware Only hardware, including spacers and support devices, approved by the Owner shall be used with steel reinforcement and the hardware shall meet the following requirements: a) All supports or support systems shall be capable of withstanding the loads to be placed on them. b) Except for tie wire, embedded hardware within 50 mm of exposed surfaces shall be stainless steel, galvanized steel, or of a non-metallic material verified not to react with concrete and approved by the ministry prior to use. c) Tie wire shall be 1.2 or 1.6 mm in diameter and shall be annealed ferrous wire except for the tie wire used to tie stainless steel reinforcing bars to stainless steel reinforcing bars, reinforcing steel bars, and shear studs, which shall be Type 316 LN or Type 316L, stainless steel wire. d) Bar chairs for supporting stainless steel reinforcing bars shall be non-metallic. Concrete chairs shall not be used to support stainless steel reinforcing bars. e) Concrete chairs shall not be used except in footings and against granular surfaces. June 2017 Page 5 of 13 SSP 109S17