SUMMARY OF PRICES FOR PLUMBING WORK Only Labour Rate PART - I SANITARY FIXTURES, C.P. FITTINGS & TOILET REQUISITES. Rs.

Transcription

1 B.O.Q. FOR SANITARY AND WATER SUPPLY INSTALLATION WORK OF INDIAN ARCHEOLOGICAL SOCIETY, B-17 QUATAB INSTITUTIONAL AREA, NEW DELHI SUMMARY OF PRICES FOR PLUMBING WORK Only Labour Rate PART - I SANITARY FIXTURES, C.P. FITTINGS & TOILET REQUISITES Rs. PART - II SOIL, WASTE, VENT & RAIN WATER PIPES AND FITTINGS Rs. PART - III WATER SUPPLY Rs. TOTAL Rs.

2 LABOUR S.NO. DESCRITPION QTY UNIT RATE AMOUNT PART - I, SANITARY FIXTURE 1 Fixing White Vitreous China, wall hung European type Water Closet (EWC) with low water consuming concealed flushing cistern with dual flushing fitting and accessories including W.C connecter,ci /galvanised steel chair carries with CP brass screw,or other fixing arrangements with white solid plastic seats and lids, CP bass hinges rubber buffers conforming to IS :2548 part -1, including cutting and making good the wall etc. complete. Make: Hindware - Studio Wall mounted closet Cat. No & CONCEALED FLUSHING CISTERN (GEBERIT White- CAT.No / VIEGA) 32 Nos. 2 Fixing vitreous china large flat back urinal basin of size 590mmx375mmx390mm deep 15mm dia C.P. spreader pipe, 32mm dia C.P. brass domical waste,32mm C.P. brass bottle trap & wall flange complete, cast iron hangers for support including cutting and making good the walls wherever required. Make : Hindware Model : Flat back Large Colour : White 8 Nos. 3 Fixing vitreous china urinal partition with necessary C.P. secrewed as required of approved design. 12 Nos. 4 Installing, testing & commissioning of infra-red sensor controlled electronic automatic flushing system for urinals comprising light sensing device & solenoid valve of approved make including cutting & making good the walls & floors as required. 8 Nos. 5 Prpviding & fixing Jaquar- Pressmatic urinal valve auto closing system with built-in control cock complete with fittings. R/O 6 Fixing white vitreous china wash-basin with C.I. brackets painted white, 32 mm. dia. C.P. brass waste with C.P. brass chain and rubber plug, 32 mm. dia. C.P. brass bottle trap and unions complete, including cutting and making good walls wherever required. (a) Flat back wash basin size 580x450 mm. with single 15 mm. C.P. brass pillar tap (Cat. No of Hindware or equivalent). R/O (b) Oval wash basin (above counter type) size 520x460 mm. (Cat. No of Hindware). 27 Nos.

3 7 Fixing 600mmx450mm (3 sq ft.)bevelled edge mirror of superior glass (of approved make) complete with 6mm thick asbestos sheets ground fixed to wooden cleats with CP brass screws & washers. 27 Nos. 8 Fixing stainless steel sink of AMC or equivalent make with R.S. brackets including painting with 40mm C.P.brass waste connected to 40mm G.I./Plastic pipe with necessary unions complete cutting & making good the walls wherever required. a) Single bowl with drain board having size 940x465 mm with C.P. brass waste complete 5 Nos. b) Double tub type with both side drain board and bowl size 500x400x200mm 1 No. 9 Fixing in position 15 mm dia C.P.brass sink mixture for hot & cold with fitting ( Jaqar Floorntine cat. No. 5163) 6 Nos. 10 Fixing in position C.P.brass 15mm dia nominal bore bib cock with wall flange complete. ( Jaquar Florentine series) 6 Nos. 11 Fixing CP brass long body bib cock with wall flange complete. ( Jaquar Florentine series) 6 Nos. 12 Fixing in position china ware toilet paper holder of approved design. ( Jaquar Code. AKB-35751) 32 Nos. 13 Fixing CP brass towel rail complete with CP brass brackets fixed to the wooden cleats with CP brass screws size 600x20mm. ( Jaquqr Code. AKB-35711) 20 Nos. 14 Fixing liquid soap dispenser with simple push lever fitted with liquid soap (one time) including cutting and making good the walls, wherever required. a) Make: jaquar -"Continentel' Catalogue No.1135N. or approved equivalent) 20 Nos. 15 Fixing C.P brass Health faucet with 8mm dia l meter long flexible tube and wall hook. a) Make: Jaquar, "Allied" Range Catalogue No.573, (with 8mm long flexible tube and wall hook) 32 Nos. 16 Fixing 15mm C.P.brass angle valve with C.P copper connecting pipe 375mm long and nuts, washer with C.P. brass flange complete, including cutting and making good the walls, wherever required. a) Make: Jaquar, Florentine Range Catalogue No. 5053, 95 Nos. 17 Fixing storage type water heater of Venus/Racold make of following capacity with brackets, nuts & bolts grouted in wall with 1:2:4 cement concrete mix (1 cement:2 coarse sand:4 stone aggregates) with connection to vent inlet & outlet complete including cutting & making good the walls where require in all respect complete..

4 a) 25 ltrs 4 No. b) 35 ltrs. 7 No. 18 Fixing 15 mm C.P. brass Wash basin mixer with complete fittings of approved quality. Make : (Jaquar,Florentine Range Catalouge No: 5357). 27 Nos. 19 Fixing C.P Over head shower with complete fittings. a) Make: Jaquar, "Allied " Range Catalogue No 497 N, 6 Nos. 20 Fixing wall mixer (3 in 1) with wall flanges complete. a) Make : Jaquar.Florentine, Catalouge No Nos. TOTAL FOR PART - I, SANITARY FIXTURES & FITTINGS PART - II, SOIL WASTE & VENT PIPES & FITTINGS 21 Fixing sand cast iron /cast iron spun soil, waste & vent pipes with all fittings of approved make such as collars, junctions, bends, offsets, M.S.holders bat clamp, lead joints cutting & making good the walls, floors complete with painting of pipes and fittings with two coats of synthetic enamel paint of an approved quality & shade over a coat of red oxide primer including earth work, excavation of trenches, refilling, consolidation etc. a) 75 mm dia 5 Mtrs. b) 100 mm dia 500 Mtrs. c) 150 mm dia 10 Mtrs. 22 Fixing sound insulated Polyproplene piping system as per ON EN 1451-Part 1-6 & EN Part 1-5 with 3 layer pipe made of PP- C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dba as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.25gms/cm3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring incluiding painting with ordinary cement based paint for external installation. (POLOPLAST - PKNG) a) 75 mm (OD) - POLO KAL NG 5 Mtrs. b) 110 mm dia POLO KAL NG 500 Mtrs. c) 160 mm dia POLO KAL NG 10 Mtrs. 23 Fixing in position the following G.I. medium class soil/waste/vent pipes as per IS: 1239 part 1 & part II with all necessary specials complete cutting chase/holes in wallas/floors and making good the same including painting the embedded pipes with two coats of anticorrosives bitumastic paint complete in all respects. a) 32 mm dia 30 Mtrs.

5 b) 40mm dia 10 Mtrs. c) 50mm dia 10 Mtrs. 24 Fixing sound insulated Polyproplene piping system as per ON EN 1451-Part 1-6 & EN Part 1-5 with 3 layer pipe made of PP- C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dba as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.25gms/cm3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring. (POLOPLAST - PKNG) - For indirect waste/sinks, wash bassin etc.) a) 40 mm (OD) - POLOKAL NG 30 Mtrs. b) 50 mm (OD) - POLO KAL NG 10 Mtrs. c) 75 mm (OD) - POLO KAL NG 10 Mtrs. 25 Fixing C.I. cowls to following vent pipes:- a) 75 mm dia b) 100 mm dia 16 Nos. 26 Fixing in position the following CI floor traps of self - cleaning design or a trap with not less than 50 mm water seal, with sand cast iron or CP screwed down/hinged grating as approved complete including embedding the trap in cement concrete 1:2:4 and making good the floors wherever required. a) 100mm dia inlet x 100 mm dia outlet 40 Nos. b) 100mm dia inlet x 75 mm dia outlet 5 Nos. 27 Fixing PP white Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections (McAlpine, UK). a) 110 mm inlet & 110 mm outlet. 40 Nos. b) 110 mm inlet & 75 mm outlet. 5 Nos. 28 Laying cement concrete 1:2:4 mix (1 cement:2 coarse sand : 4 stone aggergate 20 mm & down gauge) 75 mm in bed and alround CI soil, waste and rain water pipes under floors including centering and shuttering wherever required. a) 75 mm dia 5 Mtrs. b) 100mm dia 185 Mtrs. 29 Fixing cast brass, clean out plugs with suitable insert key for opening,male threaded joint with G.I socket caulked to soil pipe waste pipe of C.I pipe as required complete as shown in drawing. a) 100 mm dia 6 Nos. b) 160 mm dia 3 Nos.

6 30 Fixing clean out cap plug (FCO ) for cleaning of same material composition as per item no. 1 above ( POLO KAL NG). a) 110 mm dia POLO KAL NG 6 Nos. b) 160 mm dia POLO KAL NG 3 Nos. 31 Fixing inlet fittings with one or more inlets fabricatd from 100mm dia G.I. Pipe and welded G.I. sockets and fixed to C.I. Trap with lead joint and set in cement concrete as per drawing and design complete. 30 Nos. 32 Fixing, testing and commissioning of pipe inlet fittings fabricated with P.P. Pipe with maximum 3 inlets 40, 50 & 75 mm OD size poloplast pipe, fixed to 'P' traps including Dripseal/Pipe seal/solvent weld joint/rubber ring joint complete. 30 Nos. 33 Fixing of Floor Drain points formed of 65x50/40mm elblow of G.I. fitted to pipe with 75mm dia stainless steel grating with frame of approved make complete including cost of cutting and making good the walls and floors. 15 Nos. 34 Fixing of Floor Drain points formed of 65x50/40mm elblow of POLO KAL NG fitted to pipe with 75mm dia stainless steel grating with frame of approved make complete including cost of cutting and making good the walls and floors. 15 Nos. 35 Fixing rain water UPVC pipes (IS:4985) including all fittings (plain or door) e.g. bends, junction, cowels, offsets access pieces, jointing with rubber ring/solvent cement joints including cutting chase or holes in walls and floor and making good wherever required. a) 110 mm dia 10 Mtrs. b) 160 mm dia 90 Mtrs. 36 Making Khurras with average minimum thickness of 5cm Cement Concrete 1:2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate) over HDPE sheet (400 microns min. thickness), finished with 12mm Cement Plaster 1:3 (1 Cement : 3 Coarse Sand, and mixed with waterproofing compound) and a coat of neat cement rounding the edges, making & finishing complete. a) Khurra Size 230 x 230mm, for 75/100mm dia outlet with 5mm thick circular/square vertical C.I grating. 12 Nos. b) Khurra Size 450 x 450mm, for 100/150mm dia outlet with 5mm thick circular/square vertical C.I grating. 6 Nos. 37 Erection, testing and commissioning of submersible pump with cast iron body, bronze impellers, stainless steel, shaft and water lubricated bearings. The characteristics (both the pumps shall operate simultaneously, if required) Sump pump suitable for storm water drainage. a) No. of pumps - 2 nos. b) capacity LPM 1 Set c) heads - 6 to 8mtr

7 d) motor as required. 38 Fixing vertical /horizontal C.I. Grating for following rain water pipes. a) 100mm Dia. Rain Water Pipe 12 Nos b) 150mm Dia. Rain Water Pipe 4 Nos 39 Fixing C.P hinged grating, 6mm thick with rim including setting in floor with cement mortar (of approved design) a) 125mm dia 45 Nos b) 100mm dia 15 Nos EXTERNAL DRAINAGE 40 Laying in position the following salt glazed stoneware pipes, jointing in cement sand mortar 1:1, effecting proper connections & embedding the pipes in 100mm thick cement concrete 1:3:6 all around including earth work,dugging of trenches and refilling the same as required. a) 100 mm dia 10 Mtrs. 41 Laying and jointing UPVC pipes of 6 kg cm2 including all fittings (Plain/door) i.e. bend, junction, cowl, offsets access pipes etc. and jointing with solvent cement complete as per manufacture specifications.including earth work,dugging of trenches and refilling the same as required. a) 160 mm outer dia 90 Mtrs. b) 200 mm outer dia 80 Mtrs. 42 Laying cement concrete 1: 4: 8 (1cement : 4 fine send :8 graded stone aggregate 40mm nominal size) al round S.W/RCC/UPVC pipe including bed concrete 15cm thick as per standard design. a) 160 mm outer dia 90 Mtrs. b) 200 mm outer dia 80 Mtrs. 43 Fixing in position the following stoneware glazed gully trap with CI grating and cover including embedding the trap in cement concrete 1:2:4 construction of 30 cm x 30 cm x 30 cm size brick masonry chamber plastering in CM (1:3) and cement punning etc. The weight of cover not less than 4.53 kg. and weight of the frame not less than 2.7 kg. as per specifications 150 x 100 mm size `p' or `S' trap with FPS bricks of class designation Nos.

8 44 Construction of brick masonry manholes with 75 class designation bricks in cement mortar 1:5 (1 cement : 5 fine sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) inside plastering 12mm thick with cement mortar 1:3 mix, finished with a floating coat of neat cement complete and making channels in cement concrete 1:2:4, including excavation of earth, back filling of earth around the manholes, consolidation of soil, iron steps etc. for a) Inside size 90 cm x 80 cm x 60 cm deep including Pre cast RCC manhole cover with frame 600x450 mm of grade (LD-2.5) internal diamentions. 5 Nos. b) Inside size 900 cm x 80cm exceeding 60cm depth & upto 900 cm depth including pre cast RCC manhole cover with frame circular shape 500 mm internal (MD-10) 3 Nos. 45 Construction brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56 m dia at top with 75 class designation FPS bricks in cement mortar 1:4 (1 cemnt:4 coarse sand) inside cement plaster 12mm tjick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement: 3 coarse sand : 6 graded stone aggregate, 40 mm nominal size) and making necessary channel in cement conctere 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate, 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design. a) 0.91m deep with SFRC cover and frame, 560 mm internal diameter, conforming to IS:12592, total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4 (1 cement:2 coarse sand:4 grade stone aggregate 20 mm nominal size) including centering shuttering all complete (excavation, foot rest and 12 mm thick cement plaster at all external surface shall be paid for separately) 4 Nos. 46 Extra depth for circular type manhole 0.91 m internal dia (at bottom) with FPS bricks. a) Beyond 0.91 m to 2.50m 1.5 Mtrs. 47 M.S. PVC coated foot rest fixing in manholes with 20x20x10cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) As per standard design with 20x20 mm square bar 60 Nos. 48 Laying in position reinforced cement concrete pipes (NP 2 class) with collars, jointed in cement mortar 1:2 laid over rammed and consolidated trench bed, concreting (PCC 1:4:8) 100mm thick all around joints to a width of 400mm including excavation of trenches and refilling the same as required. a) 150mm dia 50 Mtrs. b) 250mm dia 110 Mtrs.

9 49 Constructing storm water catch basin of following internal sizes in brick with cement mortar 1:3 including earth work (excavation/back filling & disposal of extra earth) M.S. top grating fabricated from M.S. angle /flats, openable & connected through M.S. hinges to the frame. Grating to be made with 45x45mm angle iron frame hinged and resting on all edges over 50x50x5mm angle iron. The top grating to have flat of size 40x5mm welded to angle iron of size 45x45mm and spaced at 20mm internal. a) Size : 500x450x600mm depth 9 Nos. b) Size : 750x750x800mm depth 3 Nos. 50 Extra depth for catch basin size 500X450X600 mm with FPS bricks 1.5 Mtr 51 Extra depth for catch basin size 750X750X800 mm with FPS bricks 1.5 Mtr 52 Construction of water re- charging well soakpit cum perforatedwell) 3.5mtr dia, and 3.5 mtr.deep (overall depth 4.5 mtr.) with 1 no 160 mm OD PVC screen pipe with ribs conforming to IS , 15 mtr. long or upto natural water stream as per required depth and disposal of excavated earth as directed, brick masonary pitching around 75 class brick in cement mortar 1:4, foundation concrete 1:4:8, 150 mm thick RCC top slab with steel reinforcement, centering and shuttering, 1 no. Pre cast RCC manhole cover and frame with 6mm thick plastic 300 mm c/c complete as per detail drawing, nothing extra will be paid. 1 No. TOTAL FOR PART - II, SOIL WASTE, VENT & RAIN WATER PIPES & FITTINGS PART - III, WATER SUPPLY 53 Fixing in position the following medium class G.I. pipes as per IS: 1239 part 1 & part II (for cold water supply) for internal water supply, cut to be required lengths including enamel paint over a coat of primer and all necessary specials, clamp, hangers, cutting chase & making good the same & effecting proper connection to fixtures / equipment etc. a) 15mm dia 10 Mtrs. b) 20 mm dia 15 Mtrs. c) 25 mm dia 25 Mtrs. d) 32mm dia 60 Mtrs. e) 40mm dia 25 Mtrs. f) 50mm dia 25 Mtrs. g) 65mm dia 15 Mtrs. 54 Fixing composite pipes of HDPE - AL with compression composite/brass fitting e.g. tee s reducer's threaded connectors etc. and clamps including jointing and cutting & making good the walls etc. complete in all respects. a) 20 (O.D) 170 Mtrs. b) 25 (O.D) 90 Mtrs.

10 c) 32 (O.D) 40 Mtrs. d) 40 (O.D) 20 Mtrs. 55 Fixing in position the following GM Bronze ball valve with operating handle of approved manufacturer including effecting connections & hydraulically tested 20 kg/sqcm. complete of approved make. a) 15 mm dia Bronze Ball Valve 3 Nos. b) 20 mm dia Bronze Ball Valve 2 Nos. c) 25 mm dia Bronze Ball Valve 3 Nos. d) 32 mm dia Bronze Ball Valve 5 Nos. e) 40 mm dia Bronze Ball Valve 7 Nos. f) 50 mm dia Bronze Ball Valve 3 No. g) 65 mm dia Bronze Ball Valve 2 No. 56 Fixing heavy duty full bore GM ball with brass arm and polythene float of approved make for following size: a) 40 mm dia 1 No. 57 Fixing insulation for hot water (internal) for pipe with on layer of 6mm thick veto flex / Kai flex for chased pipe in walls finished complete. a) For 15mm nominal bore 40 Mtr. 58 Placing and hoisting upto terrace level and making platform for Sintex make water storage tank as per standard design with complete cover, inlet, outlet pipe overfllow and drain pipe etc. complete as required. a) 5000 Ltr. Cap. 2 Nos. WATER SUPPLY EXTERNAL 59 Fixing in position the following medium class GI pipes as per IS: 1239 part 1 & part II (for cold water supply) in trenches cut to be required length including anti bitumastic paint and sand filling alround the pipes and all necessary specials complete with digging of trenches, refilling consolidations of earth etc. a) 15mm dia 10 Mtrs. b) 20 mm dia 20 Mtrs. c) 25mm dia 10 Mtrs. d) 32mm dia 25 Mtrs. e) 40mm dia 20 Mtrs. 60 Fixing in position 100mm dia G.I vent pipe (inverted 'L' shaped) with puddle flange and brass perforated puff grating on water tank all complete. 5 Nos. 61 Fixing in position the following GM vertical check valve of approved manufacturer including effecting connections complete of approved make. a) 40 mm dia 2 Nos.

11 b) 50 mm dia 2 Nos. 62 Two coats anti corrosive painting of water supply external pipes and filling sand 75 mm thick all around a) 15mm dia 10 Mtrs. b) 20 mm dia 20 Mtrs. c) 25mm dia 10 Mtrs. d) 32mm dia 25 Mtrs. e) 40mm dia 20 Mtrs. 63 Fixing C.I. Manhole frame & cover for under ground water tanks of 116 kg. Weight including painting with 3 coats of anticorrosive paint, grouting with PCC 1:2:4 and finishing. 5 Nos. 64 Ditto as above item but for O.H. tank of 38kg. Weight. RO WATER SUPPLY BOOSTER PUMPS 65 Erect, test and commissioning of horizontal, centrifugal, openwell submersible monoblock pumps capable of delivering 2 LPS against 35 Mtr. head (3 H.P.) complete with starter and motor, of required as per manufacture of Kirloskar/ equivalent make. 2 Nos. 66 Fixing in position in RCC walls the following, MS-C-class1'-3" long flanged pipe sleeves with puddle flange in cebtre of sleeve including drilling of flanges and threading piping as per IS standard and as per drawings. a) 150 mm dia with both sides flanged 3 Nos. b) 100 mm dia with both sides flanged 2 Nos. c) 80 mm dia with one side flanged and other side screwed. 1 No. d) 80 mm dia with both side flanged 1 Nos. e) 50 mm dia with both sides flanged 1 Nos. f) 50 mm dia with one side flanged and other side screwed. 1 Nos. 67 Fixing water meter spiral (enclosed) type of ISI approved make with C.I cover & frame copmlete with Locking arrangements of 32dia. RO TOTAL FOR PART - III, WATER SUPPLY WORK