Fibreglass poles: table of general features

Transcription

1 432 Poles

2 Poles 433 POLES

3 434 Fibreglass poles Fibreglass poles: table of general features h pole diam. Ø recommended recomended on base sinking h. mn Ø 60 acc Ø 60 acc Ø 60 acc Ø Ø Ø 60 0 Ø Ø 60/ Ø 60/ Ø 60/ Fibreglass poles have a round or cone-shaped cross-section (dimensions depend on mechanical requirements). Compared with aluminium or steel poles they offer the following advantages: - lighter weight - less maintenance - surfaces are not attacked by corrosive agents - electrically insulated - less dangerous when impact occurs - extremely flexible in the wind. Certificated poles: These poles are recommended for small-size luminaires (decorative factor), in private areas, (anti-vandalism factor). They can be installed both on a base or buried according to measurements acc 5 pole h a. h u. 200 w/o window h a h u. 250 w/o window h a h u. 250 w/o window h a h u. 300 w/o window h a h u. 350 w/o window acc. 50 base for acc 5 black In f.g. nylon; supplied with burying anchor. For use with poles max 1900 high. Connection Ø 60. Cone-shaped fibreglass pole, black, corrosion resistant, mechanical high-resistance and UV stabilized.

4 Fibreglass cone-shaped poles C 583/683/ A B ø50 acc 1284 cone-shaped pole with window -120 h a h u. window (50x194) h a h u. 500 window (50x194) h a h u. 600 window (50x194) Cone-shaped pole in f.g., black, corrosion-proof, high mechanical resistance and UV-stabilised. Complete with inspection window, fuse and terminal block cover. C A B ø POLES acc 1278 cone-shaped pole without window -120 h a h u. w/o window h a h u. 500 w/o window h a h u. 600 w/o window Cone-shaped pole in f.g., black, corrosion-proof, high mechanical resistance and UV-stabilised.

5 436 Scored pole ø 100 Fluted pole made of extruded aluminium, anodised by 15/20µ thick tin salt electrocoating; black, graphite or natural oxidised colour. With die-cast inspection window (191x55 mm), protective fuse holder, 10A fuse, 4-pole/3-way removable terminal block = 6 sqmm, 4 sqmm connection. With hole for insertion of power supply cable. Die-cast aluminium adapter, Ø60 mm. The version with base is supplied with a base and 4 log bolts to be sunk into the ground, bolts and caps. Standard insulation class II. When using Insulation Class I fixtures, appropriate grounding connections should be included in the system. NOTE: The possibility to attach an assembly to the pole is subject to a wind pressure resistance assessment in the areas regulated by CNR- UNI standard , according to load assumptions in UNI UNI 40/6 standard. An accurate and suitable protection or insulation of the surfaces involved is recommended to avoid any direct contact with the new masonry or concrete screed. 75 acc. 299 log bolt Log bolts are to be always bought with the pole acc upward arm 444 ø acc curved arm black s. silver Tropicalised steel. Attach to accessories 1364/1365 and pole acc. 1408/1409. black /1500 ø black sil sil To be attached to acc. 1364/5 ø ø 120 acc. 211 Sector connection s. silver graphite Made of aluminium. To be used with acc. 210 for pole mounting ø100 use acc ø /2100 acc downward arm 1600 black black sil sil To be attached to acc. 1364/5 and to pole 1408/9. acc. 367 cover for poles ox. black ox. nat graphite Made of aluminium. To be used when a particular aesthetic finish is desired. 211 ø 170 acc Corona black s. silver Made of die-cast aluminium. Equipped with terminal block 700 acc. 210 Sector arm s. silver graphite Made of aluminium. To be used with acc. 211 for pole mounting. 40 ø 211 acc Corona flange black s. silver Made of die-cast aluminium. With 6 arm-stop devices to reinforce the assembly. 188 ø 121 ø 100 acc. 217 connector adapter s. silver graphite Use with acc. 211 for installation on ø100 poles acc. 327 arm s. silver graphite Die-cast aluminium. To be used with acc. 302 for wall mounting or 300/211 for the pole. ø acc. 300 Oliva connection s. silver graphite In aluminium. For installation on pole of the arms acc acc. 328 arm s. silver graphite Die-cast aluminium. To be used with acc. 302 for wall mounting, or acc. 300/211 for pole. 652 ø 72 acc. 301 arm Oliva s. silver graphite Made of aluminium. To be used with acc.300/303/304/309 and 304 for pole or with acc 302/303/304/309 wall mounting..

6 Scored pole ø L ENERGIA CHE TI ASCOLTA. ø100 Inspection window with easily removable terminal block for quick connection. The dimension of the plinth depends on the type of post, the composition, the ground and material. to seal protection band impermeable material Pole PVC Tube cement sand hole Cava 60x35 r17.5 acc 1409 scored pole Ø 100 h a h u. 500 oxy black h a h u. 600 oxy black h a h u. oxy black h a h u. 500 oxy natural h a h u. 600 oxy natural h a h u. oxy natural h a h u. 500 graphite h a h u. 600 graphite h a h u. graphite L ENERGIA CHE TI ASCOLTA. ø100 Inspection window with easily removable terminal block for quick connection. For correct installation of pole and base, the ceiling cap should be fitted as shown in the assembly drawing featured opposite mm POLES acc 1408 scored pole with base Ø 100 h a oxy black h a oxy black h a oxy black h a oxy natural h a oxy natural h a oxy natural h a graphite h a graphite h a graphite Log bolt is to be bought separately acc ø20 Cement base dimensions (subject to soil variations) for underground sinking of the 4 log bolts of acc

7 438 Scored pole ø 120 Fluted pole made of extruded aluminium, anodised by 15/20µ thick tin salt electrocoating; black, graphite or natural oxidised colour. With die-cast inspection window (191x55 mm), protective fuse holder, 10A fuse, 4-pole/3-way removable terminal block = 6 sqmm, 4 sqmm connection. With hole for insertion of power supply cable. Die-cast aluminium adapter, Ø60 mm. The version with base is supplied with a base and 4 log bolts to be sunk into the ground, bolts and caps. Standard insulation class II. When using Insulation Class I fixtures, appropriate grounding connections should be included in the system. NOTE: The possibility to attach an assembly to the pole is subject to a wind pressure resistance assessment in the areas regulated by CNR- UNI standard , according to load assumptions in UNI UNI 40/6 standard. An accurate and suitable protection or insulation of the surfaces involved is recommended to avoid any direct contact with the new masonry or concrete screed. 75 acc. 299 log bolt Log bolts are to be always used with the pole acc curved arm bla s. silver Tropicalised steel. Attach to accessories1464/1465 and to poles acc. 1508/ / acc upward arm 1430 bla bla sil sil To be attached to acc. 1464/5 and to pole 1508/ acc. 129 curved arm bla Tropicalised steel, black cationic electrocoating. Apply to acc.1464/1465 and to poles acc. 1508/ /2030 acc downward arm 1530 bla bla sil sil To be attached to acc. 1464/5 and to pole 1508/9. ø acc. 300 Oliva connection s. silver graphite In aluminium. For installation on pole of the arms acc ø 240 acc Corona bla s. silver graphite Made of die-cast aluminium. For max 6 arms acc1462 or Equipped with terminal block. 652 ø 72 acc. 301 Oliva arm s. silver graphite Made of aluminium. To be used with acc.300/303/304/309 and 304 for pole or with acc 302/303/304/309 wall mounting 40 ø ø 125 acc Corona flange bla s. silver graphite Made of die-cast aluminium. With 6 arm-stop devices to reinforce the assembly acc. 327 arm s. silver graphite Die-cast aluminium. To be used with 300/211 for the pole mounting. ø 214 ø ø 121 ø acc. 211 Sector connection s. silver graphite Made of aluminium. To be used with acc. 210 for pole mounting ø120. acc. 222 base pole cover s. silver bla graphite Made of die-cast aluminium.to be used as base pole cover acc. 1493/1308/ acc. 328 arm s. silver graphite Die-cast aluminium. To be used with 300/211 for the pole mounting. 700 acc. 210 Sector arm s. silver graphite Made of aluminium. To be used with acc. 211 for pole mounting.

8 Scored pole ø L ENERGIA CHE TI ASCOLTA. ø120 Inspection window with easily removable terminal block for quick connection. The dimension of the plinth depends on the type of post, the composition, the ground and material. to seal protection band impermeable material Pole PVC Tube cement sand hole Cava 60x35 60x35 r17.5 r17.5 acc 1509 scored pole Ø 120 h a h u. 500 oxy black h a h u. 600 oxy black h a h u. oxy black h a h u. oxy black h a h u. 500 oxy natural h a h u. 600 oxy natural h a h u. oxy natural h a h u. oxy natural h a h u. 500 graphite h a h u. 600 graphite h a h u. graphite h a h u. graphite Double fuse and standard knife switch available upon request. L ENERGIA CHE TI ASCOLTA. ø120 Inspection window with easily removable terminal block for quick connection. For correct installation of pole and base, the ceiling cap should be fitted as shown in the assembly drawing featured opposite mm POLES acc 1508 scored pole with base Ø 120 h a oxy black h a oxy black h a oxy black h a oxy natural h a oxy natural h a oxy natural h a graphite h a graphite h a graphite Double fuse and standard knife switch available upon request. Log bolt is to be bought separately acc ø20 Cement base dimensions (subject to soil variations) for underground sinking of the 4 log bolts of acc

9 440 Scored pole Lione Ø 120 Fluted pole made of extruded aluminium, anodised by 15/20µ thick tin salt electrocoating; black, graphite or natural oxidised colour. With die-cast inspection window (191x55 mm), protective fuse holder, 10A fuse, 4-pole/3-way removable terminal block = 6 sqmm, 4 sqmm connection. With hole for insertion of power supply cable. Die-cast aluminium adapter, Ø60 mm. The version with base is supplied with a base and 4 log bolts to be sunk into the ground, bolts and caps. Standard insulation class II. When using Insulation Class I fixtures, appropriate grounding connections should be included in the system. NOTE: The possibility to attach an assembly to the pole is subject to a wind pressure resistance assessment in the areas regulated by CNR- UNI standard , according to load assumptions in UNI UNI 40/6 standard. An accurate and suitable protection or insulation of the surfaces involved is recommended to avoid any direct contact with the new masonry or concrete screed. 75 acc. 299 log bolt Log bolts are to be always used with the pole ø ø 120 acc. 212 ring s. silver graphite Made of aluminium. To be used with acc. 214/215 for ø120 pole mounting. acc. 151 Lione cube bla s. silver Made of die-cast aluminium. To be used when installing the products on poles Ø acc. 129 curved arm bla Tropicalised steel, black cationic electrocoating. Apply to acc.1464/1465 and to poles acc. 1308/ acc. 210 Sector arm s. silver graphite Made of aluminium. To be used with acc. 211 for pole mounting acc. 153 arm attachment bla s. silver Made of die-cast aluminium. To be used with acc. 151 when installing curved arms on poles. ø ø 120 acc. 211 Sector connect. s. silver graphite Made of aluminium. To be used with acc. 210 for pole mounting ø / acc upward arm 1430 bla bla sil sil To be attached to acc. 1464/5 and to pole 1308/9. ø acc. 305 end cap s. silver graphite To be used when no fixture is installed on acc 210 to improve appearance /2030 acc downward arm 1530 bla bla sil sil To be attached to acc. 1464/5 and to pole 1308/ acc. 327 arm s. silver graphite Die-cast aluminium. To be used with acc. 302 for wall mounting, or 300/211 for pole mounting acc curved arm bla s. silver Tropicalised steel. Attach to acc.1464/1465 and on poles acc. 1308/ acc. 328 arm s. silver graphite Die-cast aluminium. To be used with acc. 302 for wall mounting, or 300/211 for pole mounting. ø 430 ø acc. 222 base pole cover sil.sab bla graphite Made of die-cast aluminium.to be used as base pole cover acc. 1493/1308/1508.

10 Scored pole Lione Ø L ENERGIA CHE TI ASCOLTA. ø120 Inspection window with easily removable terminal block for quick connection The dimension of the plinth depends on the type of post, the composition, the ground and material. to seal protection band impermeable material hole Cava 60x35 r x35 r Pole cement PVC Tube sand acc 1309 scored pole Lione Ø 120 h a h u. oxy black h a h u. oxy natural h a h u. graphite Double fuse and standard knife switch available upon request. L ENERGIA CHE TI ASCOLTA. ø120 Inspection window with easily removable terminal block for quick connection For correct installation of pole and base, the ceiling cap should be fitted as shown in the assembly drawing featured opposite. ø mm POLES 1100 acc 1308 scored pole Lione with base h a oxy black h a oxy natural h a graphite Double fuse and standard knife switch available upon request. Log bolt is to be bought separately acc Cement base dimensions (subject to soil variations) for underground sinking of the 4 log bolts of acc

11 442 Cone-shaped poles Equipped with inspection window (293x94 mm), removable 4-pole terminal block, max. cross-section 16 sqmm. Supplied with 2 16A safety fuses. With hole for insertion of power supply cable; with holes at different heights according to use. The version with base is supplied with a base and 4 log bolts to be sunk into the ground, bolts and caps. Standard insulation class II. NOTE: The possibility to attach an assembly to the pole is subject to a wind pressure resistance assessment in the areas regulated by CNR-UNI standard , according to load assumptions in UNI standard 40/6. ø acc. 300 Oliva connect. s. silver graphite In aluminium. For installation on pole of the arms acc. 210/301/327/ ø 72 acc. 301 Oliva arm s. silver graphite Made of aluminium. To be used with acc. 300/303/304/309 for the pole installation or with acc. 302/303/304/309 for the wall. acc. 210 Sector arm s. silver graphite Made of aluminium. To be used with acc. 300 for pole mounting acc. 328 arm s. silver graphite Die-cast aluminium. To be used with acc. 302 for wall mounting or 300/211 for the pole acc. 327 arm s. silver graphite Die-cast aluminium. To be used with acc. 302 for wall mounting or 300/211 for the pole.

12 Cone-shaped poles 443 ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, Inspection door with easily removable terminal board for quick connection. Concrete base dimensions (subject to soil variations) hole 100x50 Cava 100X50 acc 1481 steel cone-shaped to be buried-with window h a h u. 500 silver h a. 0 h u. 500 silver h a h u. 500 silver h a h u. 500 graphite h a. 0 h u. 500 graphite h a h u. 500 graphite POLES ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, Inspection door with easily removable terminal board for quick connection. Concrete base dimensions (subject to soil variations) acc 1480 steel cone-shaped with base-with window h a silver h a. 0 silver h a silver h a graphite h a. 0 graphite h a graphite

13 Steel poles ø 102 ø102, silver colour steel pole. Complete with inspection window with removable terminal strip. The version with base comes complete with a plinth, 4 tie rods to be buried, bolts, nuts and caps. Use with accessories 465/467 and with articles Agadir and Monza is recommended acc. 465 pole arm s. silver The pole arm for Monza. To be used with poles art. 1492/ acc. 467 pole arm s. silver The pole arm for Monza. To be used with poles art. 1492/1494.

14 Steel poles ø ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, Inspection door with easily removable terminal board for quick connection. Concrete base dimensions (subject to soil variations) ø102 hole 100x50 r25 Cava 100x50 r acc 1492 steel pole to be buried h a h u. silver ø102 40mm POLES ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, Inspection door with easily removable terminal board for quick connection. For correct installation of pole and base, the ceiling cap should be fitted as shown in the assembly drawing featured opposite. 191 acc 1494 steel pole with base h a silver mm ø acc. 222 base pole cover s. silver To be used as base pole cover acc. 1492/1494. ø 430 ø Concrete base dimensions (subject to soil variations)

15 446 Steel poles ø 120 Hot-dip galvanised steel poles. Equipped with inspection window (293x94 mm), removable 4-pole terminal block, max. cross-section 16 sqmm. Supplied with 2 16A safety fuses. With hole for insertion of power supply cable; with holes at different heights according to use. The version with base is supplied with a base and 4 log bolts to be sunk into the ground, bolts and caps. Standard insulation class II. NOTE: When using Insulation Class I fixtures, appropriate grounding connections should be included in the system. NOTE: The possibility to attach an assembly to the pole is subject to a wind pressure resistance assessment in the areas regulated by CNR-UNI standard , according to load assumptions in UNI standard 40/6. Milan Padova Installation acc. 222 on the pole base. 163 acc. 368 mast-top-pole connec. galvanized In galvanized steel. To be used as a mast-top-pole connection on poles acc. 1491/1493. ø 430 ø acc. 222 base pole cover s. silver bla graphite In die-cast aluminium. To be used as a base pole cover acc

16 Steel poles ø ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, ø25 Inspection door with easily removable terminal board for quick connection. Concrete base dimensions (subject to soil variations) ø121 hole 150x50 Cava 150x50 r25 r25 acc 1491 steel pole to be buried h a h u. galvanized h a h u. galvanized h a. 0 h u. galvanized Supplied with end cap and holes to let the cables through. acc 1491 painted pole with colour choice h a h u. painted h a h u. painted h a. 0 h u. painted Supplied with end cap and holes to let the cables through. The painted version is with RAL selected colour as indicated. POLES ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, ø25 Inspection door with easily removable terminal board for quick connection. For correct installation of pole and base, the ceiling cap should be fitted as shown in the assembly drawing featured opposite mm ø acc 1493 steel pole with base h a galvanized h a. 6 galvanized h a. 7 galvanized Supplied with end cap and holes to let the cables through. 40mm ø 20 acc 1493 steel pole with base h a painted h a. 6 painted h a. 7 painted Supplied with end cap and holes to let the cables through. The painted version is with RAL selected colour as indicated. Concrete base dimensions (subject to soil variations)

17 448 Steel pole ø Hot-dip galvanised steel poles. Equipped with inspection window (293x94 mm), removable 4-pole terminal block, max. cross-section 16 sqmm. Supplied with 2 16A safety fuses. With hole for insertion of power supply cable; with holes at different heights according to use. The version with base is supplied with a base and 4 log bolts to be sunk into the ground, bolts and caps. Standard insulation class II. NOTE: When using Insulation Class I fixtures, appropriate grounding connections should be included in the system. NOTE: The possibility to attach an assembly to the pole is subject to a wind pressure resistance assessment in the areas regulated by CNR-UNI standard , according to load assumptions in UNI standard 40/6. Arcugnano - Vicenza Installation acc. 223 on the pole base. 163 acc. 368 mast-top-pole connec. galvanized In galvanized steel. To be used as mast-top-pole connection on poles acc. 1505/1503. ø 430 ø acc. 223 base pole cover s. silver Die-cast aluminium. To be used as base pole cover acc

18 Steel pole ø ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, ø25 Inspection door with easily removable terminal board for quick connection. Concrete base dimensions (subject to soil variations) ø ø hole Cava 150x50 150x50 Cava r25150x50 r25 acc 1503 steel pole to be buried h a h u. galvanized Supplied with end cap and holes to let the cables through. acc 1503 painted pole with colour choice h a h u. painted Supplied with end cap and holes to let the cables through. The painted version is with RAL selected colour as indicated. POLES ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, ø25 Inspection door with easily removable terminal board for quick connection. For correct installation of pole and base, the ceiling cap should be fitted as shown in the assembly drawing featured opposite ø mm ø acc 1505 steel pole with base h a galvanized Supplied with end cap and holes to let the cables through. acc 1505 painted steel pole with base h a painted Supplied with end cap and holes to let the cables through. The painted version is with RAL selected colour as indicated. 40mm ø 20 Concrete base dimensions (subject to soil variations)

19 450 Steel pole Aliante ø Hot galvanised steel poles. Complete with inspection window (239x64mm), with 4-pole and 16mm2 maximum cross section removable terminal strip. With 2 16A rated protection fuses. Arranged with the power cable entry hole. The version with base comes complete with a plinth, with 4 tie rods to be buried, bolts, nuts and caps. Class II insulation as a standard feature. Attention is required when using fixtures with class I insulation since earthing connections must be foreseen. N.B.: The possibility of combining a composition to the pole is subordinated to verifying the ability to withstand the wind force in the areas foreseen by the ENV standards. In accordance with the load assumptions foreseen in the EN standards. For technical information see chapter. Pole installation example of acc Supplied with 3W triple lens LED module, white or standard bluee. ø acc. 450 LED head CTL LED whi LED blue To be installed on pole to give an aesthetic finish acc. 406 Aliante arm s. silver graphite In steel. It permits the pole application acc. 1475/ acc. 407 Aliante arm s. silver graphite In steel. It permits the pole application acc. 1475/1476.

20 Steel pole Aliante ø ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, ø121 Inspection door with easily removable terminal board for quick connection. Concrete base dimensions (subject to soil variations) ø hole 150x50 r25 Cava 150x50 r25 acc 1475 Aliante pole to be buried h a. 0 h u. silver Supplied with end cap and holes to let the cables through. The painted version is with RAL selected colour as indicated. Cycle pathway versions are available on request. ø121 ø ø mm POLES 1380 ON REQUEST Possibility of supplyng poles with the following colour paint finishes: RAL 3003, 5011, 7026, 9011, 8015, , 7016, 9006, 7037, 6004, 8019, 6011, 7022, 1015, Inspection door with easily removable terminal board for quick connection. 239 For correct installation of pole and base, the ceiling cap should be fitted as shown in the assembly drawing featured opposite acc 1476 Aliante pole with base h a. 0 silver Supplied with end cap and holes to let the cables through. The painted version is with RAL selected colour as indicated. Cycle pathway versions are available on request. Concrete base dimensions (subject to soil variations)

21 452 Aliante composition examples ø121 ø121 ø121 ø ø193 ø193 ø193 ø193 ES. ac 91-1 Giovi 1 Giovi 1 pole to be selected between acc. 1475/76* 1 arm acc /90 2 ACC /1476 Example of project with art SAP-T 150. Area 15x30 m; h=8 m ES. ac 71-1 Metropolis 1 Metropolis 1 pole to be selected between acc. 1475/76* 1 arm acc /90 ACC /1476 Example of project with art SAP-T 150. Area 15x30 m; h=8 m ES. ac 76-2 Metropolis 2 Metropolis 1 pole to be selected between acc. 1475/76* 1 arm acc /90 1 arm acc / /1476 Example of project with 1752/1753 SAP-T150. Area 20x30m; h=8/4,5 13 ACC 407 ACC 406 ACC ES. ac 23-2 Monza 2 Monza 1 pole to be selected between acc. 1475/76* 2 arms acc /90 1 led head acc ACC 407 ACC /1476 Example of project with HCI- T 150. Area 20x30 m; h=8 m

22 ARKINOTEComposition examples ø121 Pø121 L Hø ø ø G4500 ø193 ø193 ø ACC 407 ACC /1476 Example of project with CDM-TT 150. Area 15x30 m; h=8 m ES. ac 15-1 Torpedo 1 Torpedo 1 pole to be selected between acc. 1475/76* 1 arm acc /90 1 attachment acc / POLES ACC 407 ACC /1476 ACC 455 Example of project with 1240/1244 CDM-TT150 JM-T70. Area 30x20 m; h=8/4, ES. ac 17-2 Torpedo 2 Torpedo 1 pole to be selected between acc. 1475/76* 1 arm acc /90 1 arm acc /88 2 attachments acc / ACC /1494 Example of project with 1584 JM-TS 150. Area 15x30m; h= ES. ac 26-2 Agadir 2 Agadir 1 pole to be selected between acc. 1492/1494* 2 arms acc ACC /1494 Example of project with 1755 HCI-T 150. Area 15x30m; h=8 ES. ac 25-1 Monza 1 Monza 1 pole to be selected between acc. 1492/1494* 1 arm acc

23 A454 BAø /4360/5260B3298/4298/5198/6198 R5750/6750/7750 ø120 ø121 ø /6860/8760 Examples of assemblies ES. ac 74-1 Metropolis 1 Metropolis 1 pole to be selected between acc. 1491/93* 1 Sector arm acc /51 1 Sector connect. acc /53 1 ring acc /55 1 attachment acc /57 1 tie-rod acc ACC 210 ACC 211 ACC /93/97/98 ACC 213 ACC 215 Example of project with art SAP-T 150. Area 10x7 m; h=5 m 2012 ES. b 30-2 Metropolis 2 Metropolis 1 pole to be selected between acc. 1508/1509* 1 Oliva acc /71 2 arms Sector acc /51 RACC 210 ACC /1509 Example of project with 2 metropolis SAP-T70. Area 20x20m; h=5; I= ES. b82 with scored pole ø120 2 Lanterna art. 1760/61/62/63/64/65 1 pole to be selected between acc 1508 e 1509* 1 Oliva acc /71 2 Oliva arms acc /73 2 attachments acc /1509 ACC 300 ACC 301 ACC 309 Example of project with art SAP-E 100. Area 15x15 m; h=3 m ES. ac95-2 Capri 2 Capri 1 pole to be selected between acc.1491/93* 2 Sector arm acc /51 1 Sector connect. acc /53 1 ring acc /55 2 attachment acc /59 2 tie-rods acc pole attach. acc ACC 210 ACC 211 ACC /1493 ACC 214 ACC 215 ACC 155 Example of project with art JM-E 150. Area 16x8 m; h=5 m 2840

24 TEL10 Examples of assemblies ø102 ø121 ø120 Eø121 L6000/7000/0 3720/4720/5620/ HOT /1494 Example of project with art JM-TS 150. Area 15x20m; h=5 11 ACC 300 ACC 301 ACC ES. ac 34 - Montecarlo 2 Montecarlo art. 3171/72/73 1 pole to be selected between acc. 1492/94* 1 Oliva acc /71 2 Oliva arms /73 2 threaded connec. acc POLES ACC 210 ACC 300 ACC /1503/5 Example of project with art HCI-T150. Area 20x30m; h= /1509 Example of project with art JMTS 150. Area 14x7 m; h=5000mm ACC 300 ACC 301 ACC ACC 211 ACC 213 ACC /93 ACC 303 Example of project with art HCI-T150. Area 20x20m; h=5,56 10 H OES. b 28-1 Monza 2 Monza 1 pole to be selected between acc. 1491/93/1503/05* 1 Oliva acc /71 2 Sector arms acc /51 2 connection acc /86 ES. b14 with pole Ø120-2 Vista 2 Vista art. (chose one from art. 1596/98/99) 1 pole to be selected between acc e 1509* 1 Oliva acc /73 2 Oliva arms acc /71 2 attach. acc /77 ES. b 28 - with steel pole ø120-1 Torcia 1 Torcia (choose three art.) 1 pole to be selected between acc 1491 e 1493* 1 attach. arm oliva acc /73 1 Sector connect. acc /53 1 banner connect. acc /57 1 attach. acc /77