Revision Date: July 1, 2015 Version No.: 1 SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING

Transcription

1 SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING 1.1 Product Identifier Product Name JEESILC PDS Relevant Identified Uses of the Substance or Mixture and Uses Advised Against Identified uses Cosmetic raw material 1.3 Details of the Supplier of the Safety Data Sheet Company JEEN International Corporation 24 Madison Road Fairfield, New Jersey Tel: Fax: info@jeen.com Website: Emergency telephone number (Chemtrec Int l Tel - Collect calls accepted) SECTION 2 HAZARDS INGREDIENTS 2.1 Classification of the Substance or Mixture according to Regulation (EC) 1272/ Label Elements according to Regulation (EC) EU 1272/2008 Hazard pictogram Signal words Hazard statements Precautionary statements 2.3 Other Hazards known SECTION 3 COMPOSITION/INFORMATION ON INGREDIENTS 3.1 Substances Chemical characterization Cosmetic ingredients INCI Dimethicone CAS EC Polymer exempt Concentration 100% 3.2 Mixture - SECTION 4 FIRST AID MEASURES 4.1 Description of First Aid Measures Eye: If irritation occurs, flush eye(s) with lukewarm gently flowing water for 5 minutes. Obtain medical attention. JEESILC PDS-100 Page 1 of 6

2 Skin: Inhalation: Oral: te to Physician: health effects expected. If irritation does occur flush with lukewarm, gently flowing water for 5 minutes. If irritation persists, obtain medical advice. If symptoms are experienced remove source of contamination or move victim to fresh air. If irritation persists, obtain medical advice. If irritation or discomfort occurs, obtain medical advice. Treat according to person s condition and specifics of exposure. 4.2 Indication of any immediate Medical Attention and special Treatment needed information available. SECTION 5 FIRE FIGHTING MEASURES 5.1 Flash Point >248 F / >120 C (Closed Cup) >482 F / >250 C (Cleveland Open Cup) 5.2 Flammable Limits in Air 5.3 Auto ignition Temperature 5.4 Extinguishing Media On large fires use dry chemical, foam or water spray. On small fires use carbon dioxide (C02), dry chemical or water spray. Water can be used to cool fire exposed containers. 5.5 Fire Fighting Measures Self-contained breathing apparatus and protective clothing should be worn in fighting large fires involving chemicals. Determine the need to evacuate or isolate the area according to your local emergency plan. Use water spray to keep fire exposed containers cool. 5.6 Unusual Fire Hazards SECTION 6 ACCIDENTAL RELEASE MEASURES 6.1 Methods and Material for Containment and Cleaning Up Determine whether to evacuate or isolate the area according to your local emergency plan. Observe all personal protection equipment recommendations described in Section 5 and 8. For large spills, provide diking or other appropriate containment to keep material from spreading. If dikes material can be pumped, store recovered material in appropriate container. Clean up remaining materials from spill with suitable absorbent. Clean area as appropriate since spilled materials even in small quantities may present a slip hazard. Final cleaning may require use of steam, solvents or detergents. Dispose of saturated absorbent or cleaning materials appropriately, since spontaneous heating may occur. Local, state and federal laws and regulations may apply to releases and JEESILC PDS-100 Page 2 of 6

3 SECTION 7 HANDLING AND STORAGE disposal of this material, as well as those materials and items employed in the cleanup of releases. You will need to determine which federal, state and local laws and regulations are applicable. Section 13 and 15 of this SDS provide information regarding certain federal and state requirements. 7.1 Precautions for Safe Handling Use with adequate ventilation. Avoid eye contact. Avoid skin contact. 7.2 Conditions for Safe Storage including Use reasonable care and store away from oxidizing any incompatibilities materials. SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION 8.1 Component Exposure Limits There are no components with workplace exposure limits. 8.2 Engineering Controls Local ventilation: General Ventilation: 8.3 Personal Protective Equipment for Routing Handling Eyes: Skin: Suitable Gloves: Inhalation: Suitable Respirator: 8.4 Personal Protective Equipment for Spills Eyes: Skin: Inhalation / Suitable Respirator: Precautionary Measures: Comments: te: should be needed Recommended. Use proper protection safety glasses as a minimum Washing at mealtime and end of shift is adequate. Handle in accordance with good industrial hygiene and safety practices. respiratory protection should be needed. should be needed. Use proper protection safety glasses as a minimum. Washing at mealtime and end of shift is adequate. respiratory protection should be needed. Avoid eye contact. Use reasonable care. When heated to temperature above 150 C (300 F) in the presence of air, product can form formaldehyde vapors. Physical and health hazards information is readily available from Jeen International per this Material Safety Data Sheet. These precautions are for room temperature handling. Use at elevated temperature or aerosol / spray applications may require added precautions. SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES 9.1 Information on basic Physical and Chemical Properties Physical Form: Color: Liquid Clear to Slightly Hazy Liquid JEESILC PDS-100 Page 3 of 6

4 Odor: Characteristic Odor Specific 25 C Viscosity 100 cst Freezing/Melting Point: Boiling Point: >65oC Vapor 25 C: Vapor Density: Solubility in Water: ph: Volatile Content: Flash Point: >248 F / > 120 C (closed cup) > 482oF / > 250oC (Cleveland open cup) Auto ignition Temp: Flammability Limits in Air: SECTION 10 STABILITY AND REACTIVITY 10.1 Stability Stable 10.2 Incompatible Materials Strong oxidizing material can cause a reaction 10.3 Conditions to Avoid 10.4 Hazardous Polymerization Will not occur 10.5 Hazardous Decomposition Products Thermal breakdown of this product during fire or very high heat conditions may evolve the following decomposition products: Carbon oxides and traces of incompletely burned carbon compounds. Silicone dioxide. Formaldehyde. SECTION 11 - TOXICOLOGICAL INFORMATION 11.1 Information on Toxicological Effects known applicable information. SECTION 12 - ECOLOGICAL INFORMATION 12.1 Environmental Fate and Distribution Air: Water: Soil: This product is a high molecular weight liquid polymer which has a very low vapor pressure. As a result it Is unlikely to become an atmospheric contaminant unless generated as an aerosol. This product has a very low water solubility (< 100 ppb). As it has a specific gravity of < 1, if discharged to water, it will initially form a surface film. As the product is nonvolatile and has a high binding to sewage sludge. If the sewage sludge is subsequently spread on soil, the silicone product is expected to degrade. If discharged to surface water, this product will bind to sediment. If discharged in effluent to a waste water treatment plant, the product is removed from the aqueous phase by binding to sewage sludge. If the sewage sludge JEESILC PDS-100 Page 4 of 6

5 Degradation: 12.2 Environmental Effects Toxicity to Water Organisms: Toxicity to Soil Organisms: Bioaccumulation: is subsequently spread on soil, the silicone product is expected to degrade. This product, polydimethylsiloxane, degrades is soil abiotically to form smaller molecules. These in turn are either biodegraded in soil or volatilized into the air where they are broken down in the presence of sunlight. Under appropriate conditions, the ultimate degradation products are inorganic silica, carbon dioxide and water vapor. Due to the very law water solubility of this product, standard OECD protocols for ready and inherent biodegradability are not suitable for measuring the biodegradability of this product. The product is removed > 80% during the sewage treatment process. Based on analogy to similar materials this product is expected to exhibit low toxicity to aquatic organisms. Experiments show that when sewage sludge containing polydimethylsiloxane is added to soil is had no effect ton soil micro-organisms, earthworms or subsequent crops grown in the soil. This product is a liquid and is a high molecular weight polymer. Due to its physical size, it is unable to pass through or be absorbed by biological membranes. This has been confirmed by testing or analogy with similar products Fate and Effects in Waste Water This product or similar products has been shown to be Treatment Plants non-toxic to sewage sludge bacteria Eco toxicity Classification Criteria HAZARD PARAMETERS (LC50) HIGH MEDIUM LOW ACUTE AQUATIC TOXCITY (MG/L) <=1 >1 AND <=100 >100 ACUTE TERRESTRIAL TOXICITY <=100 >100 AND <=2000 >2000 te This table is adapted from Environmental Toxicology and Risk Assessment ASTM STP 1179, P.34, This table can be used to classify the Eco toxicity of this product when Eco toxicity data is listed above. Please read the other information presented in the section concerning the overall ecological safety of this material SECTION 13 - DISPOSAL CONSIDERATIONS 13.1 Waste Treatment Methods Dispose of in accordance with federal, state and local regulations. SECTION 14 TRANSPORTATION INFORMATION 14.1 DOT Road Shipment Information (49 CFR ) t subject to DOT JEESILC PDS-100 Page 5 of 6

6 14.2 Ocean Shipment (IMDG) t subject to IMDG code 14.3 Air Shipment (IATA) t subject to IATA regulations SECTION 15 REGULATORY INFORMATION 15.1 TSCA Status All chemical substances in this material are included on or exempted form listing on the TSCA Inventory of Chemical Substances EPS SARA Title III Chemical Listings Section 302 Extremely Hazardous Substances (40 CFR 355): Section 304 CERCLA Hazardous Substances (40 CFR 302): Section 311 / 312 Hazard Class (40 CFR 370): Acute: Chronic: Fire: Pressure: Reactive: Section 313 Toxic Chemicals (40 CFR 372): te: 15.3 Supplemental State Compliance Information California: Massachusetts: present or non-present in regulated quantities. Chemicals are listed under the 313 Toxic Chemicals section only if they meet or exceed a reporting threshold. Warning: This product contains the following chemical(s) listed by the State of California under the Sage Drinking Water and Toxic Enforcement Act of 1989 (Proposition 65) as being known to cause cancer birth defects or other reproductive harm: known ingredient regulated by MA Right- to Know Law Present New Jersey CAS NUMBER WT % COMPONENT NAME >60.0 Polydimethylsiloxane Pennsylvania SECTION 16 OTHER INFORMATION CAS NUMBER WT % COMPONENT NAME >60.0 Polydimethylsiloxane Disclaimer: As the conditions or methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of this product. Information contained herein is believed to be true and accurate but all statements or suggestions are made without warranty, expressed or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof. Compliance with applicable federal, state and local regulations remains the responsibility of the user. JEESILC PDS-100 Page 6 of 6