Aluminium Frame Doors ATB 68 Environmental Product Declaration acc. to ISO Holder of the declaration

Transcription

1 Aluminium Frame Doors ATB 68 Environmental Product Declaration acc. to ISO Holder of the declaration Content of the declaration Lindner AG Bahnhofstraße Arnstorf Germany Product information Certification system DGNB Certification system LEED Certification system BREEAM General information

2 Product information Product description The door leaf ATB 68 is an Aluminium frame door with glass inlay. The door leaf thickness is 68 mm. Application area For the application inside of buildings, e.g. offices, conference rooms, industrial workspaces as well as rooms for training and research. Base materials Base materials per door leaf 1 m x 2,2 m with single glazing System components Tempered/ laminated safety glass Material proportions [%] for 32 db proportions [%] for 37 db Glass ~ 60,6 ~ 70,0 Glazing frame Aluminium ~ 37,3 ~ 28,6 Gasket EPDM ~ 1,5 ~ 0,9 Thin plate Timber < 0,5 < 0,5 Screws Steel < 0,5 < 0,5 Screws Stainless Steel < 0,5 < 0,5 Clip-on Plastic < 0,5 < 0,5 Base materials per door leaf 1 m x 2,2 m with double glazing System components Tempered/ laminated safety glass Material proportions [%] for 32 db proportions [%] for 37 db proportions [%] for 42 db Glass ~ 63,9 ~ 66,0 ~ 72,6 Glazing frame Aluminium ~ 32,7 ~ 30,8 ~ 25,2 Gasket EPDM ~ 2,7 ~ 2,6 ~ 1,7 Thin plate Timber < 0,5 < 0,5 < 0,5 Screws Steel < 0,5 < 0,5 < 0,5 Screws Stainless Steel < 0,5 < 0,5 < 0,5 Clip-on Plastic < 0,5 < 0,5 < 0,5 Attention: Accessories like ironmongery, hinges and door handles are supplied by third. If available, we can add the declaration of the supplier. Material explanation Glass ESG, Tempered safety glass VSG, Laminated safety glass Aluminium Extruded aluminium profiles are coated (powder coated or anodized), cut and mounted as a frame with screws and corner connectors. Editor: PM Partition Systems Page 2 of 12 Rev. 02 dated

3 Die Lindner Group ist Certification System Not listed characteristics do not apply to this product. 1 Environmental Quality ENV1.1 Life Cycle Impact Assessment Data for a project specific LCA can be gathered observing the valid standards. Therefore, an additional expenditure of time and money might occur. ENV1.2 ENV2.1 Local Environment Impact Life Cycle Impact Assessment Primary Energy Component Tempered/ laminated glass safety proportion Glazing frame - - Gasket Thin plate Screws Clip-on Total VOC GISCODE Other Giscode BS 10 not applicable for powder coating without lead, mercury, cadmium and chrome (VI) compounds Data for a project specific EPD can be gathered observing the valid standards. Therefore, an additional expenditure of time and money might occur. Editor: PM Partition Systems Page 3 of 12 Rev. 02 dated

4 1 Economic quality ECO1.1 Life Cycle Cost Door leaves can be expected to remain durable for up to 50 years (acc. to BBSR table, code no to , state 11/2011, published by the Federal Institute for Research on Building, Urban Affairs and Spatial Development). 1 Sociocultural & Functional Quality SOC1.2 Indoor Air Quality Products of the Linder company are fabricated with materials of low emission like VOC or formaldehyde. SOC1.3 Acoustic Comfort The single door leaf can be designed with a valued sound insulation of 42 db according to DIN EN ISO SOC1.4 Visual Comfort The consists mostly of glass. Therefore, daylight from the facades can reach the corridor. SOC2.1 Accessibility Our products can be designed according to the guidelines and regulations of accessibility. Therefore, they facilitate the access to rooms. Editor: PM Partition Systems Page 4 of 12 Rev. 02 dated

5 1 Technical Quality TEC1.2 Sound Insulation The single door leaf can be designed with a valued sound insulation of 42 db according to DIN EN ISO TEC1.6 Deconstruction and Disassembly The door leaves and frames can be dismantled and reutilized. Lindner system product are designed to allow assembly o site with almost no rubbish. Certain rubbish can not be avoided on site, but will principally be recycled by specialised companies. 1 Process quality PRO1.5 PRO2.1 Documentation for Facility Management Environmental Impact of Construction Utilisation, maintenance and care instructions are created to the usual extent and can be provided. The compliance with project-related requirements regarding low-waste, low-noise and low-dust site as well as measures for soil and ground water protection are ensured by specialised in-house departments. An appropriate verification can be created and implemented on request by specialised personnel. Due to the delivery of finished door leaves and frames that do not have to be processed on site, the product contributes to a noise-free and dust-free site The packaging is selected project-related to produce as little waste as possible. PRO2.2 Construction Quality Assurance All documents relevant for project documentation can be provided. 1 DGNB GmbH Editor: PM Partition Systems Page 5 of 12 Rev. 02 dated

6 Certification system LEED Not listed credits do not apply for this product. And its related logo, is a trademark owned by the U.S. Green Building Council Sustainable Sites Construction Activity Pollution Prevention The compliance with project-related requirements of an ESC plan is ensured by specialised in-house departments. A complete ESC plan can be created and implemented on request by specialised personnel. Materials and Resources Construction and Demolition Waste Management Planning Building Life Cycle Impact Reduction Building Product Disclosure and Optimization Environmental Product Declaration Waste that cannot be avoided on site is preferentially put into recycling processes by means of waste management facilities. A complete CWM plan can be created and implemented on request by specialised personnel. Lindner products have a long life expectancy Moreover, certain products can systematically be dismantled and reused after small processing (C2C). Data for a project specific LCA can be gathered observing the valid standards. Therefore, an additional expenditure of time and money might occur. Data for a project specific EPD can be gathered observing the valid standards. Therefore, an additional expenditure of time and money might occur. Editor: PM Partition Systems Page 6 of 12 Rev. 02 dated

7 Building Product Disclosure and Optimization Sourcing of Raw Materials Components for double glazed door leaf with 36 db Tempered/ laminated safety glass proportion Recycled content Pre- Consumer Post- Consumer Production site ~ 63,9 % 20 % 5 % Arnstorf Glazing frame ~ 32,5 % 0 % 30 % Arnstorf Gasket ~ 2,7 % 0 % 0 % Arnstorf Floor Gasket ~ 0,8 % 0 % 0 % Arnstorf Thin plate < 0,5 % 0 % 0 % Arnstorf Screws < 0,5 % 0 % 0 % Arnstorf Clip-on < 0,5 % 0 % 0 % Arnstorf Total 100 % ~ 19.4 % Depending on the door leaf design a recycled contet of up to 20.3% is possible. Building Product Disclosure and Optimization Material Ingredients Construction and Demolition Waste Management As manufacturer of products, Lindner fulfils the obligations towards the EU chemical directive REACH and created its own REACH declaration. The aim of the REACH regulation (Registration, Evaluation and Authorization of CHemicals) is to capture materials produced and used in the EU and to determine and record their impact on health and environment. Due to the delivery of finished door leaves and frames that do not have to be processed on site, the product contributes to a noise-free and dust-free site. The packaging is selected project-related to produce as little waste as possible. Lindner products are designed to avoid waste during assembly. Waste that cannot be avoided on site is preferentially put into recycling processes by means of waste management facilities. Editor: PM Partition Systems Page 7 of 12 Rev. 02 dated

8 Indoor Environmental Quality Minimum Acoustic Performance Construction Indoor Air Quality Management Plan Indoor Air Quality Assessment The single door leaf can be designed with a valued sound insulation of 42 db according to DIN EN ISO and insulates the rooms of incoming sound. The compliance with project-related requirements of an IAQ plan is ensured by specialised in-house departments. A complete IAQ plan can be created and implemented on request by specialised personnel. Lindner door systems are made from materials that show almost no emissions of e.g. VOC and formaldehyde. Daylight Acoustic Performance The consists mostly of glass. Therefore, daylight from the facades can reach the corridor. The single door leaf can be designed with a valued sound insulation of 42 db according to DIN EN ISO and insulates the rooms of incoming sound. Editor: PM Partition Systems Page 8 of 12 Rev. 02 dated

9 Certification system Not listed characteristics do not apply to this product Management Man 02 Responsible construction practices Generally, all companies of the Lindner Group largely fulfil the requirements of an environmental management system. For companies of the Lindner Group certified according to ISO 14001, ISO 50001, SCC**- and OHSAS, further specific environmental and safety targets are defined in conjunction with the annual management review. The implementation of environmental protection and relevant legal regulations are defined in the Lindner intern guideline Environmental protection. Man 03 Man 05 Construction site impacts Life cycle cost and service life planning The compliance with project-related requirements regarding low-waste, low-noise and low-dust site as well as measures for soil and ground water protection are ensured by specialised in-house departments. An appropriate verification can be created and implemented on request by specialized personnel. Lindner products have a long life expectancy (due to the raw materials, production processes and high production quality). Moreover, certain products can systematically be dismantled and reused after small processing (C2C). Doors can be expected to remain durable for up to 50 years (acc. to BBSR table, code no to , state 11/2011, published by the Federal Institute for Research on Building, Urban Affairs and Spatial Development). Health and Wellbeing Hea 01 Visual comfort The consists mostly of glass. Therefore, daylight from the facades can reach the corridor. Hea 02 Indoor air quality Lindner partition systems are made from materials that show almost no emissions of e.g. VOC and formaldehyde. Editor: PM Partition Systems Page 9 of 12 Rev. 02 dated

10 Hea 05 Acoustic performance Energy The single door leaf can be designed with a valued sound insulation of 42 db according to DIN EN ISO and insulates the rooms of incoming sound. Ene 01 Energy efficiency Data for a project specific EPD can be gathered observing the valid standards. Therefore, an additional expenditure of time and money might occur. Materials Mat 01 Life cycle impacts Data for a project specific EPD can be gathered observing the valid standards. Therefore, an additional expenditure of time and money might occur. Mat 03 Wst 01 Responsible sourcing of materials Waste Construction waste management Environmental Pollution Lindner door systems are made from materials with a high recycling content. Local suppliers are preferred. The company Lindner is certified according to the environmental management system according to DIN EN ISO Lindner door leaves and frames are produced in such a way that they can be installed on site with as little waste as possible. Waste that cannot be avoided on site is preferentially put into recycling processes by means of waste management facilities. Pol 08 Noise reduction The single door leaf can be designed with a valued sound insulation of 42 db according to DIN EN ISO and insulates the rooms of incoming sound. Editor: PM Partition Systems Page 10 of 12 Rev. 02 dated

11 General information CO 2 & Waste In order to reduce waste from demolition and building measures, waste streams are dedicated to recycling processes. The verification can be done by the company Lindner. The used transport packaging (timber, cardboard, foils) can be recycled. Where possible, they are collected separately and supplied to a proper recycling (packaging regulation). Lindner system products are delivered to the construction site in ready-for-assembly condition. This means that no work or possibly minor work has to be done on the product. In this way, only little waste or no waste is generated on site. The used transport packaging can in large part be recycled. Only certified waste management companies are entrusted with the disposal conforming to the law for waste that cannot be avoided. Vision 2020: Co2 neutral and waste-free location Less is more. Much less is our aim! The vision: It is our aim to further develop Lindner production sites in CO2 neutral and waste-free locations. We derived concrete aims from the vision to make an entrepreneurial contribution to the reduction of CO2 emissions as well as all commercial waste. The analysis of major pollutants is of course given top priority. Environmental Management Acting sustainably, saving resources For Lindner, responsibility towards humans and environment is as important as the quality of the products. For this reason, an environmental management system acc. to DIN EN ISO is established company-wide and largely certified. Our central environment programme comprises the responsible and sustainable use of resources, the reduction of CO2 emissions and a continuous improvement process to achieve our environmental objectives. An integrated management system evaluates the production of Lindner products regularly according to ecological aspects and adapts the processes to current standards. Our principles comprise an active waste management in all business units from waste prevention concept to waste balance. We also keep an eye on preceding stages of the value added chain. Environmental aspects also play a major role in the selection of our suppliers Editor: PM Partition Systems Page 11 of 12 Rev. 02 dated

12 Energy Management Towards an environmentally friendly future. The national and international supply situation asks for a targeted and effective use of resources and environmentally friendly forms of energy. At Lindner, an energy management system based on DIN EN ISO controls the procurement of energy sources centrally for all locations as well as their transformation, delivery and distribution to affiliated companies. Energy saving and the change of fossil and nuclear energy to ecological sources of energy are the core of all measurements to implement energetic business objectives. Thus, every single employee is aware of its role in sustainable, operative project management. Due to many small improvements, for example the improvement of compressed air loss, the utilisation of waste heat and targeted light control, we could achieve massive energy savings in the last years. Especially at future-oriented investments, for example the installation of new production plants, we pay attention to the implementation of resource-saving solutions. Editor: PM Partition Systems Page 12 of 12 Rev. 02 dated