Technical Application Guide for UP-SHINE LED Cylinder UP-PD02B-10W

Transcription

1 Technical Application Guide for UP-SHINE LED Cylinder UP-PDB-1W

2 Introduction PD whole lamp adopts straightforward design with stylish appearance, easy to install, simple and generous, paying more attention to leisure and comfort. It gives space a clear and lively feelings. Different color of surface ring is optieral, which could create diversified light atomosphere according to different environment. The lamp adopts high quality reflector which has good reflective rate and light output > %. AL3 Aluminum radiator in sand blast oxidation treatment provides excellent heat dissipation and corrosion resistance. High lumen COB chip with CRI>. PF>.9, THD<%, passed EMC test with strong antijamming capability. Besides, it possesses shortcircuit protection and overvoltage protection function, showing high safety performance. Up to 7% energy saving compared to standard CFL Long lifetime of 5, hours 15 / /3 beam angle CCT: 7K 3K K 5K No UV/IR light Environment friendly, without Mercury or any other hazardous substances Internal Driver Application notes IP for indoor use only Professional electrician for installation only Switch off before installation Do not touch when in use Keep away from hot steam and corrosive gas Application Areas Applicable for residential lighting in bedroom, living room, corridor etc, also suitable for commercial lighting in office, hotel, restaurant etc. Certificate

3 Product Information 13 Ø Technical Specifications Model Voltage Power Power Factor UP-PDB-1W AC1-V 1W.9 UP-PDB-1W-D AC3V 1W.9 Driver data Sheet Lumen (±5%) CCT 5 7K 3K 9 K 7 5K 1 7K 3K 55 K 3 5K Beam angle Lifespan CRI Dimmable Dimension 15 / /3 5,h No Ø*13mm 15 / /3 5,h Yes Ø*13mm Fixture Compatibility Rated Wattage Driver data DIM Non dim Input rated Voltage AC3V AC1-V Frequency 5Hz 5/Hz Input Voltage AC-V AC5-5V Efficiency 7% % Total load Wattage 1W±.5W 1W±.5W Power Factor.9.9 Rated input current.5a.1a Full load output Voltage DC-75V DC-75V Rated output current 1mA 1mA Output current range 1mA±5% 1mA±5% Power tolerance ±5% ±5% Current output tolerance ±5% ±5% Dimming range %-1% Dimmer Triac dimmers Short circuit protection PASS PASS Over voltage protection PASS PASS Over temperature protection PASS PASS Withstand voltage Electrical Classification Ingress Protection Operating Temp Operating Humidity Storage Temp 1W Ⅰ IP - o C~5 o C ~9% - o C~5 o C

4 Spectral Distribution 7K 3K..7. Max=59 [1.=].73 SDCM F7K. Max=55 [1.=] SDCM F3K.5..3 x=.51 y= x=.5 y= K 5K. Max=57 [1.=].1 SDCM FK. Max=7 [1.=]. SDCM F5K x=.35 y= x=.351 y= Photometric Diagram 7K 3K /+ 1 9 MH=1m C/ C9/7 Flux out: 57. lm /+ 1 9 MH=1m C/ C9/7 Flux out:. lm AVERAGE BEAM ANGLE(5%): 3. DEG Height Eavg, Emax Angle: 3. deg Diameter AVERAGE BEAM ANGLE(5%): 3.5 DEG Height Eavg, Emax Angle: 3.13 deg Diameter K 5K /+ 1 9 MH=1m C/ C9/7 Flux out: 5. lm /+ 1 9 MH=1m C/ C9/7 Flux out: 1.1 lm AVERAGE BEAM ANGLE(5%): 3.5 DEG Height Eavg, Emax Angle: 3.1 deg Diameter AVERAGE BEAM ANGLE(5%): 3. DEG Height Eavg, Emax Angle: 3.97 deg Diameter

5 Polar Diagram Comparison -15 O O 15 O -1 O 1 O -9 O 9 O - O 1 O -3 O 3 O O AVERAGE BEAM ANGLE (5%): 3.DEG C/, 3.9 deg C3/1, 3.1 deg C/, 3. deg C9/7, 39.3 deg Driver lifetime & LED light decay rate Driver Lifetime LED Light Decay Rate 9 11%. Lifetime (hours) o C 75 o C 5 o C 95 o C 15 o C Capacitor Tc ( o C) % Luminous Flux 15% 1% 95% 9% 5% % 75% FLUX.1.5 U'V' 7% LifeTime (hours) Temperature The testing is operated at 5 C The lifetime of capacitor, minimum of 5, hours if operated at 15 C, will be doubled whenever the temperature drops 1 C The highest withstand temperature of IC, MOS could be 1 C The highest withstand temperature of LED junction temperature is 15 C 1 Temperature ( o C) IC Capacitor MOS PCB LED 1 11:13:13 11:31:1 11:9:1 1:7:1 1:5:1 1:3:1 13:1:1 13:19:1 13:37:1 Time 13:55:1 1:13:1 1:31:1 1:9:1 15:7:1 15:3:1 :1:1 :19:1 :37:1 Fitting Environmental temperature The driver lifespan is based on capacitor working temperature.

6 Installation 1 Take out the accessories from accessory box. Determine mounting location and knock the plastic anchor into ceiling, fix bracket with screw into the ceiling. 3 L N L = BROWN N = BLUE = YELLOW-GREEN Connect the corresponding polarities between the wire on the ceiling and input wire by screw terminal. After proper alignment and adjustment between lamp and mounting plate, then rotate the lamp clockwise until it is stuck firmly by mounting plate. Packaging Information SIZE(CM) N.W/pc (KGS) G.W.(KGS) Q'TY(PCS) Carton 3.5** '' standard container '' standard container CTNS Q'TY(PCS) VOLUME(CBM) Phone: Add: nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China