Technical Application Guide for UP-SHINE LED Downlight

Transcription

1 Technical Application Guide for UP-SHINE LED Downlight UP-DL94-8-2W

2 Introduction Up-shine ultra thin LED downlight DL94 model adopts side-emitting design, high lumen SMD LED, PMMA LGP with even light output. Equipped with aluminum heating sink, 94- V fire rated PC housing and internal driver. Dimmable version available, it shares great popularity by the excellent dimming effect. Upshine ultra thin LED downlight is suitable for various applications perfectly even narrow and low ceiling. Up to 7% energy saving compared to standard CFL Long lifetime of 4, hours Triac dim 12 wide beam angle 2-21mm cutout CCT: 3K 4K 5K 57K No UV/IR light Environment friendly, without Mercury or any other hazardous substances Application notes IP4 for indoor use only Professional electrician for installation only Switch off before installation Do not touch when in use Keep away from hot steam and corrosive gas Application Areas It is designed for general lighting applications in office, supermarket, shop, school, hotel, etc. It is also widely used for public areas, such as stairway, lobby, reception, corridors etc. Certificate

3 Product Information 33 Ø197 Technical Specifications Model Voltage Power Power Factor Driver data Sheet Driver data DIM Non dim Input rated Voltage AC23V AC1-24V Frequency 5Hz 5/6Hz Input Voltage AC2-24V AC85-265V Efficiency 85% 88% Total load Wattage 2W±5% 2W±5% Power Factor.9.9 Rated input current.12a.23a Full load output Voltage DC65-78V DC55-78V Rated output current 24mA 25mA Output current range 24mA±5% 25mA±5% Power tolerance ±5% ±5% Current output tolerance ±5% ±5% Dimming range 8%-1% Dimmer Triac dimmers Short circuit protection PASS PASS Over voltage protection PASS PASS Over temperature protection PASS PASS THD 2% 23V Fixture Compatibility Rated Wattage Electrical Classification Lumen (±5%) Beam angle Ingress Protection CCT Lifespan CRI Dimmable Dimension UP-DL94-8-2W 1-24V 2W K 4h 8 No Ø23*33mm cutout 2-21mm UP-DL94-8-2W 1-24V 2W K 4h 8 No Ø23*33mm cutout 2-21mm UP-DL94-8-2W 1-24V 2W K 4h 8 No Ø23*33mm cutout 2-21mm UP-DL94-8-2W 1-24V 2W K 4h 8 No Ø23*33mm cutout 2-21mm UP-DL94-8-2W-D 23V 2W K 4h 8 Yes Ø23*33mm cutout 2-21mm UP-DL94-8-2W-D 23V 2W K 4h 8 Yes Ø23*33mm cutout 2-21mm UP-DL94-8-2W-D 23V 2W K 4h 8 Yes Ø23*33mm cutout 2-21mm UP-DL94-8-2W-D 23V 2W K 4h 8 Yes Ø23*33mm cutout 2-21mm Operating Temp Operating Humidity Storage Temp 2W Ⅱ IP4-2 o C~45 o C ~9% -2 o C~65 o C Ø23

4 Spectral Distribution 3K 4K.8 Max=6515 [1.=2] 5.27 SDCM F3K.8 Max=8473 [1.=2] 4.6 SDCM F4K x=.4581 y= x=.3976 y= K 57K.8 Max=623 [1.=2] 3.11 SDCM F5K.8 Max=863 [1.=2] 5.91 SDCM F57K x=.3625 y= x=.3348 y= Photometric Diagram 3K 4K / MH=1m C/18 C9/27 Flux out: 1211 lm / MH=1m C/18 C9/27 Flux out: 1195 lm AVERAGE BEAM ANGLE(5%): DEG Height Eavg, Emax Angle: 112.9deg Diameter AVERAGE BEAM ANGLE(5%): DEG Height Eavg, Emax Angle: 111.3deg Diameter 5K 57K -/ AVERAGE BEAM ANGLE(5%): DEG MH=1m 6.5 C/18 C9/ Flux out: 1316 lm Height Eavg, Emax Angle: deg Diameter -/ AVERAGE BEAM ANGLE(5%): DEG MH=1m 6.5 C/18 C9/ Flux out: 1337 lm Height Eavg, Emax Angle: deg Diameter

5 Polar Diagram Comparison -15 O -/+18 O 15 O -12 O 12 O -9 O 9 O -6 O O -3 O 3 O O AVERAGE BEAM ANGLE (5%): DEG C/18, deg C3/21, deg C6/24, deg C9/27, deg Driver lifetime & LED light decay rate Driver Lifetime LED Light Decay Rate 9 11%.4 Lifetime (hours) o C 75 o C 85 o C 95 o C 15 o C Capacitor Tc ( o C) % Luminous Flux 15% 1% 95% 9% 85% % 75% FLUX.1.5 U'V' 7% LifeTime (hours) Temperature The testing is operated at 25 C The lifetime of capacitor, minimum of 5, hours if operated at 15 C, will be doubled whenever the temperature drops 1 C The highest withstand temperature of IC, MOS could be 12 C The highest withstand temperature of LED junction temperature is 15 C 7 6 IC Temperature ( o C) Capacitor MOS LED Fitting 1 Transformer Environmental temperature 14:34:57 14:46:53 14:58:53 15:1:53 15:22:53 15:34:53 15:46:53 15:58:53 16:1:53 Time 16:22:53 16:34:53 16:46:53 16:58:53 17:1:53 17:22:53 17:34:53 17:46:53 The driver lifespan is based on capacitor working temperature.

6 Installation 1. Open a hole according to the cutout size of led downlight. 2. Use screw-driver to open the driver terminal cover on the back of downlight, feed the main AC wire L. N. in terminal block respectively, then fix the cover back. 3. Hold back the spring clip then push the downlight into the hole. 4. Make sure the downlight fixed tightly in ceiling, turn on the power (Fig 1). Packaging Information SIZE(CM) N.W/pc (KGS) G.W.(KGS) Q'TY(PCS) Carton 49*49* '' standard container 4'' standard container CTNS Q'TY(PCS) VOLUME(CBM) Phone: Add: 2nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China