Energy efficiency can be measured. Measurement solutions for heating, air conditioning and ventilation.

Transcription

1 Energy efficiency can be measured. Measurement solutions for heating, air conditioning and ventilation. 1

2 Energy efficiency Utilising potential. Find out more about the various ways to increase the energy efficiency of your customers systems. The most varied of components and parameters have to be checked in order to optimise the energy consumption of a heating system or building. Regardless of whether you are analyzing heating emissions, visualising energy loss in a building, or would like to detect pipeline leaks Testo measurement solutions enable you to manage practically all your everyday work challenges with ease. Problem: heating costs are too high. Problem: stipulated particulate matter concentration must be observed. Problem: gas boiler does not ignite. Solution: set the heating system to be more efficient. Solution: determine the particle concentration in order to comply with legal standards. Solution: measure the gas flow pressure. testo 310, testo 320, testo 330 testo 380 testo 312, testo 510 Problem: return flow is too hot or too cold. Problem: energy loss due to weak spots in the heating systems. Problem: regular maintenance of water and gas pipes is timeconsuming. Solution: determine the supply and return temperature in order to set the circulation pump correctly. testo 175, testo 830, testo 922, testo 925 Solution: visualise and localise damage or superheating by means of thermography. testo 835, testo 870, testo 875i, Solution: perform pressure and load testing more time efficiently. testo 324 2

3 Problem: leaking gas pipes. Problem: harm to health due to carbon monoxide emissions. Problem: risk of carbon monoxide poisoning due to heating flue gas emissions. Solution: localise the gas leak. Solution: CO warning/measurement of the ambient air. Solution: a back pressure indicator detects and reports heating flue gas emissions. testo 316-1/-2, testo testo 315-2, testo testo Problem: heat insulating capacity of a building is unknown. Problem: building shell shows agerelated insulation damage. Problem: energy loss in the heating or air conditioning of buildings. Solution: measurement of the U-value provides the insulation characteristics of the construction material. testo 635 U-value Solution: determine the energy loss by means of thermography. testo 870, testo 875i Solution: thermographic visualisation of the entire building shell. testo 875i, testo 885 3

4 Energy efficiency Problem: insufficient air exchange rate in closed rooms. Problem: thermal discomfort in a room. Problem: bad indoor air quality. Solution: measurement and adjustment of the volumetric flow in the duct and duct outlet. testo 416, testo 410, testo 417 Solution: determine thermal radiation and air temperature, humidity and flow. testo 405, testo 425 Solution: an instrument that records the indoor air quality (temperature, flow, humidity, and CO 2 ). testo 435, testo 535 Problem: indoor climate has to be checked promptly. Problem: complaints about noise pollution. Problem: undetected risk of mould. Solution: fast room testing with mobile humidity measuring instruments. Solution: determine the noise level in order to adjust the volume. Solution: show temperature, humidity and dew point on a display. testo 608, testo 610, testo 625 testo 815, testo 816 testo 835-H1, testo 875i 4

5 Problem: formation of mould due to improper ventilation. Problem: structural damage due to material moisture. Problem: undetected moisture in walls, floors, or ceilings. Solution: monitoring of ventilation behaviour. testo 174 H, testo 175 H1 Solution: measure wood and material moisture in good time. testo 606 Solution: fast, non-destructive determination of material moisture characteristics in construction materials. testo 616 Problem: inspection and verification of restoration work carried out by tradesmen. Problem: water and moisture damage must be localised. Problem: building dehumidification measures must be documented. Solution: thermal images before and after for efficient monitoring. Solution: identify damp areas by means of thermography. Solution: show the drying process with the aid of thermography. testo 870, testo 875i testo 870, testo 875i testo 870, testo 875i, testo 885 5

6 From the Black Forest into the big, wide world. We measure it. This motto is both a slogan and also the key to success for our company, which is based in Lenzkirch in the Black Forest. For over 50 years now, everything at Testo has revolved around innovative measuring technology. Measurement solutions for demanding target groups Whether the testo 870 thermal imager, the monitoring system testo Saveris or the particulate matter measuring instrument testo 380 Testo AG excels through its high level of innovation and broad spectrum of products. Testo measuring instruments help to save you time and resources, they protect the environment and human health, and improve the quality of products and services. The high-tech instruments are used, for example, in the storage and transport of sensitive goods in the pharmaceutical and food sectors, in production and quality assurance in industry or in the monitoring of climate data in energy production and by contractors. Extensive range of training courses available. Our in-company academy offers the most extensive range of thermography training courses, both in theory and practice, in the whole of Germany: these include the basics about qualified TÜV staff and experts (TÜV - German Technical Safety Standards Authority) right through to training courses for levels 1, 2 and 3. Please contact our employee, Christian Podeswa, on or by (cpodeswa@testo.de). Service for the highest expectations. Our experts are available to answer any queries you may have concerning our service and range of products on the Testo hotline ( ). In case of service, we can guarantee you quick response times and also a loan instrument. Reliable calibration services. Testo Industrial Services, a subsidiary of Testo AG, is Germany s market leader for all calibration services. Consequently, we are also the only company able to offer ISO certificates for thermography. You can contact Testo Industrial Services by at info@testotis.de or on Individual consultation. We can offer you solution-oriented product and customer support for all areas of thermography or thermal imagers from Testo. You can reach us from Monday to Thursday from 7:30 am to 7:00 pm and on Friday from 7:30 am to 5:30 pm on ; or write us an vertrieb@testo.de. 6

7 Energy efficiency Our measurement solutions. Flue gas/particulate matter Flue gas analyzer testo Highly efficient flue gas analyzer testo Professional flue gas analyzer testo 330 LL 12 Particulate matter analyzer testo Pressure Pressure and leakage measuring instrument testo Differential pressure measuring instrument testo Leak detection Detector for gas pipe leaks testo The gas leak detection instrument with integrated pump for fast control readings testo The handy gas leak detection instrument for beginners testo Thermography Thermal imager testo Thermal imager testo 875i 21 Thermal imager testo Temperature Contact measurements Temperature measuring instruments testo 925 / Penetration/surface temperature measuring instrument testo Non-contact measurement Infrared temperature measuring instrument (2 channel) testo Infrared temperature measuring instrument testo Infrared thermometer with humidity module testo 835-H1 25 Moisture Humidity Humidity/temperature measuring instrument testo 605-H1 26 Thermo-hygrometer testo 608-H2 26 Humidity/temperature measuring instrument testo Humidity/temperature measuring instrument testo Humidity/temperature measuring instrument testo Material moisture Wood/material moisture measuring instrument testo Material moisture measuring instrument testo Data loggers Mini data logger for temperature and humidity testo 174H 29 Data logger for temperature and humidity testo 175 H1 29 Flow/multi-function Flow velocity Thermal anemometer testo Thermal anemometer testo Vane anemometer testo Vane anemometer testo Vane anemometer testo Multi-function Multi-functional measuring instrument testo Indoor air quality CO warning/measuring instrument testo CO monitor testo Back pressure indicator testo CO 2 measuring instrument testo Light/sound Sound level meter testo Sound level meter testo Lux meter testo

8 Flue gas testo 310 Flue gas analyzer testo 310 Robust design for daily use Up to 10 hours battery life Measures flue gas, draught, CO environment and pressure Quick sensor zeroing in just 30 seconds Illuminated display Documentation of measurement results via IR printer testo 310 flue gas set testo 310 incl. rech. battery and calibration protocol for the measurement of O 2, CO, hpa and C; probe 180 mm with cone, case, and mains unit incl. cable, silicon hose for pressure measurement, and 5 particle filter The testo 310 flue gas analyzer combines simple functions with a high level of measurement accuracy, and is thus perfect for all basic measurements on heating systems. Long battery lifetimes of up to 10 hours guarantee you high availability. Its easy handling and compact design make the testo 310 a robust tool for daily work even when things get rough. testo 310 flue gas set with printer testo 310 incl. rech. battery and calibration protocol for the measurement of O 2, CO, hpa and C; IR printer ( ); probe 180 mm with cone, case, and mains unit incl. cable; silicon hose for pressure measurement, 5 particle filters, and 2 rolls of thermal paper for printer Measuring range Accuracy ±1 digit Resolution Flue gas temperature 0 to +400 C ±1 C (0 to +100 C) ±1.5% of m.v. (>100 C) 0.1 C Ambient temperature -20 to C ± 1 C 0.1 C Draught measurement Pressure measurement -20 to +20 hpa -40 to 40 hpa ±0.03 hpa (-3.00 to hpa) ±1.5% of m.v. (remaining meas. range) 0.01 hpa ± 0.5 hpa 0.1 hpa O 2 measurement 0 to 21 vol. % ±0.2 vol. % 0.1 vol. % CO measurement (without H 2 compensation) 0 to 4000 ppm ±20 ppm (0 to 400 ppm) ±5% of m.v. (401 to 2000 ppm) ±10% of m.v. (2001 to 4000 ppm) Ambient CO measurement 0 to 4000 ppm ±20 ppm (0 to 400 ppm) ±5% of m.v. (401 to 2000 ppm) ±10% of m.v. (2001 to 4000 ppm) 1 ppm Efficiency testing (Eta) 0 to 120% - 0.1% 1 ppm Flue gas loss 0 to 99.9% - 0.1% Measuring instrument accessories USB mains unit incl. cable Testo IR printer Testo fast printer IRDA Spare thermal paper for printer, permanent ink Spare dirt filter Spare gas sensors Spare O 2 sensor Spare CO sensor

9 Flue gas testo 310 Robust Robust and light instrument for daily use even in rough and dirty surroundings. Illuminated display Two-line display and clear menu structure. Easy to operate and clearly legible. Automatic zeroing of sensor Automatic zeroing of the gas sensor in only 30 seconds after starting, which can be cancelled if not required. Rechargeable lithium battery Operation with rechargeable lithium battery (1500 mah) no need to change battery, up to ten hours running time, charging via USB possible. Probe filter Quickly and easily exchangeable Attachment Integrated magnets for easy fixing to burner. Condensate trap Integrated condensate trap very quick and easy to empty. 9

10 Flue gas testo 320 Highly efficient flue gas analyzer testo 320 Fast and easy menu structure Measurement of flue gas, draught, pressure, CO environment and differential temperature Also suitable for gas leak detection O 2 and CO sensor and flue gas probe with temperature probe The testo 320 is a high-quality measuring instrument for efficient flue gas analysis. Its wide measuring range makes it a reliable partner for eliminating malfunctions and emergencies, monitoring legal limit values or for daily routine work servicing heating systems. The numerous measurement menus of the testo 320 are clearly structured. Standardised menu structures, which are stored in the instrument specific to the country concerned, simplify operation depending on which standard applies to measurement. The high resolution colour display enables a detailed presentation of the measurement procedures and can be clearly read even in the worst of conditions. Options for testo 320 Optional CO sensor without H 2 compensation testo 320 testo 320 flue gas analyzer, incl. O 2 sensor, calibration protocol, and colour display testo 320 set for flue gas inspectors testo 320 with H 2 compensated CO sensor and bluetooth USB mains adapter modular flue gas probe (length 300 mm, Ø 8 mm) combustion air probe with cone (length 190 mm) testo 320 set for heating engineers testo 320 with H 2 compensated CO sensor USB mains adapter system case (height: 130 mm) testo fast printer IRDA compact flue gas probe (length 300 mm, Ø 6 mm) combustion air probe with cone (length 190 mm) Optional H 2 compensated CO sensor Optional CO low sensor Optional bluetooth Measuring range Accuracy ±1 digit Resolution Temperature -40 to C ±0.5 C (0 to C) ±0.5% of m.v. (remaining meas. range) Draught measurement to +40 hpa ±0.02 hpa or ±5% of m.v. (-0.50 to hpa) ±0.03 hpa (+0.61 to hpa) ±1.5% of m.v. (+3.01 to hpa) Pressure measurement 0 to +300 hpa ±0.5 hpa (0.0 to 50.0 hpa) ±1% of m.v. (50.1 to hpa) ±1.5% of m.v. (remaining meas. range) O 2 measurement 0 to 21 vol. % ±0.2 vol. % 0.1 vol. % CO measurement (without H 2 compensation) CO measurement (H 2 compensated) 0 to 4000 ppm ±20 ppm (0 to 400 ppm) ±5% of m.v. (401 to 2000 ppm) ±10% of m.v. (2001 to 4000 ppm) 0 to 8000 ppm ±10 ppm or ±10% of m.v. (0 to 200 ppm) ±20 ppm or ±5% of m.v. (201 to 2000 ppm) ±10% of m.v. (2001 to 8000 ppm) Flue gas loss 0 to 99.9% 0.1% CO 2 determination 0 to CO 2 max ±0.2 vol. % 0.1 vol. % digital calculation from O C (-40 to C) 1 C (> C) 0.01 hpa with fine draught option 0,001 hpa 0.1 hpa with fine pressure option 0.01 hpa 1 ppm 1 ppm For accessories and probes for testo 320, see page

11 Flue gas testo 320 High-resolution graphic display The measurement menus and measurement values are presented in detail and always well legible. Automatic zeroing of sensor Automatic zeroing of the sensor in only 30 seconds after starting, which can be cancelled if not required. Sensor exchange by the user Easy exchange of the sensors by the user no adjustment necessary. Rechargeable lithium battery Operation with rechargeable lithium battery (1500 mah) no need to change battery, up to eight hours running time, charging via USB possible. Sensor monitoring Integrated traffic light system which continuously monitors the sensor functionality. Condensate trap Integrated condensate trap very easy to empty. Efficient exchange of probes Fast and easy exchange of probes via the probe coupling. All gas paths are connected to the instrument at once with the bayonet connection. 11

12 Flue gas testo 330 Professional flue gas analyzer testo 330 Many measurement menus for analyses of heating systems, including solid fuel measurement and gas pipe test menus Integrated sensor monitoring 4 years warranty without maintenance contract Dilution to 30,000 ppm CO (testo LL) Zeroing in the flue possible (testo LL) The testo 330 LL meets the highest requirements and is capable of fulfilling all measurement tasks on heating systems. The variety of flue gas probes often negates the need for an additional measuring instrument. Other fuels can be individually defined. Gas pipe tests or solid fuel measurements can be carried out using the testo 330 LL. The measuring instrument has three high quality measurement cells for O 2, CO and NO, as well as a temperature sensor integrated into the flue gas probe, for the direct measurement of temperature, O 2, CO and NO. The sensors have an extended lifetime of up to 6 years. testo LL testo LL flue gas analyzer with long life gas sensors, incl. O 2 /CO cell; without H 2 compensation, incl. rechargeable battery and calibration protocol; with graphic display testo LL testo LL flue gas analyzer set featuring long life gas sensors with integrated draught and gas zeroing, incl. O 2 /CO cell; without H 2 compensation, incl. rechargeable battery and calibration protocol; with graphic display Options for testo 330 Optional fine draught measurement, resolution 0.1 Pa, measuring range to 100 Pa (instead of standard draught measurement) Optional fine differential pressure measurement Optional NO sensor, measuring range 0 to 3000 ppm, resolution 1 hpa Optional H 2 compensated CO cell Optional CO low sensor Optional NO low sensor Optional bluetooth Order suggestion testo 330 for service technicians and inspectors with fine pressure probe testo LL Optional: H 2 compensated CO cell Optional: Bluetooth International mains unit V AC / 6.3 V DC Modular flue gas probe, 300 mm, Ø 6 mm Combustion air temperature probe 190 mm testo BLUETOOTH printer PC analysis software easyheat USB connection cable instrument/pc Fine pressure probe Order suggestion testo 330 for Customer Service and maintenance engineers testo LL Optional: H 2 compensated CO cell Optional: Bluetooth International mains unit V AC / 6.3 V DC Modular flue gas probe, 300 mm, Ø 6 mm Combustion air temperature probe 190 mm testo BLUETOOTH printer Hose connection set System case (height: 130 mm) Measuring range Accuracy ±1 digit Resolution Temperature -40 to +1,200 C ±0.5 C (0.0 to C) ±0.5% of m.v. (remaining meas. range) Draught measurement to +40 hpa ±0.02 hpa or ± 5% of m.v. (-0.50 to hpa) ±0.03 hpa (+0.61 to hpa) ±1.5% of m.v. (+3.01 to hpa) (whichever value is the greater) Pressure measurement 0 to 300 hpa ±0.5 hpa (0.0 to 50.0 hpa) / ± 1% of m.v. (50.1 to hpa) ±1.5 % of m.v. (remaining meas. range) 0.1 C (-40 to C) ±1 C (remaining meas. range) 0.01 hpa 0.1 hpa O 2 measurement 0 to 21 vol. % ±0.2 vol. % 0.1 vol. % CO measurement (without H 2 compensation) CO measurement (H 2 compensated) 0 to 4,000 ppm ±20 ppm (0 to 400 ppm) /± 5% of m.v. (401 to 2,000 ppm) ±10% of m.v. (2,001 to 4,000 ppm) 0 to 8,000 ppm ±10 ppm or ±10% of m.v. (0 to 200 ppm) ±20 ppm or ±5% of m.v. (201 to 2,000 ppm) ±10% of m.v. (2,001 to 8,000 ppm) 1 ppm 1 ppm CO 2 determination 0 to CO 2 max ±0.2 vol. % 0.1 vol. % Option: NO measurement: 0 to 3,000 ppm ±5 ppm (0 to 100 ppm) /± 5% of m.v. (101 to 2,000 ppm) ±10% of m.v. (2,001 to 3,000 ppm) 1 ppm 12

13 Flue gas testo 330 Long life sensors The sensors of the instrument series testo 330 LL have an extended lifetime of up to 6 years. At least one sensor replacement is saved in the course of a normal working life. Sensor exchange by the user Easy exchange of the sensors by the user no adjustment necessary. Dilution CO In CO measurement, from 8,000 ppm, automatic dilution is carried out up to min. 30,000 ppm CO (only for testo LL) Long battery life Powerful Li-ion rechargeable battery no battery change. Up to eight hours life with pump running. Battery can be charged separately and in the instrument, no memory effect, no deep discharge. Sensor monitoring Integrated traffic light system which continuously monitors the sensor functionality. High-resolution colour display The measurement menus and measurement values are presented in detail and always well legible. Draught and gas zeroing Integrated gas and draught zeroing without probe removal: The probe can remain in the chimney during zeroing (only for testo LL). Flexibility with modular probe A range of probe lengths and diameters ensure a high degree of flexibility for all applications. To exchange the probe shaft, it is simply placed on the probe handle and engages. For accessories and probes for testo 330, see page

14 Flue gas testo 320/testo 330 Accessories for testo 320/330 Testo fast printer with wireless infrared interface, 1 roll of thermal paper and 4 AA batteries testo BLUETOOTH Printer with wireless bluetooth interface, incl. 1 roll of thermal paper, rech. battery and mains unit Spare thermal paper for printer, permanent ink Smoke tester incl. oil and soot papers for measuring soot in flue gas, excl. cone (order no ) Hose connection set with adapter for separate gas pressure measurement PC analysis software easyheat, for presenting measurement procedures as diagrams, tabels and for customer data management. USB connection cable instrument-pc, testo 330-1/-2 LL / testo 335 System case (height: 130 mm) for instrument, probes and accessories System case with double base (height: 180 mm) for instrument, probes and accessories Probes and accessories for testo 320/330 Compact basic flue gas probes Compact basic flue gas probe incl. cone for fixing; thermocouple NiCr-Ni; hose 1.5 m; dirt filter; length 180 mm; Ø 6 mm; Tmax. 500 C Compact basic flue gas probe incl. cone for fixing; thermocouple NiCr-Ni; hose 1.5 m; dirt filter; length 300 mm; Ø 6 mm; Tmax. 500 C Modular flue gas probes, available in 2 lengths, incl. cone for fixing, thermocouple NiCr-Ni, hose 2.2 m and dirt filter Modular flue gas probe incl. cone for fixing; thermocouple NiCr-Ni; hose 2.2 m; dirt filter; length 180 mm; Ø 8 mm; Tmax. 500 C; TÜV-certified Modular flue gas probe incl. cone for fixing; thermocouple NiCr-Ni; hose 2.2 m; dirt filter; length 300 mm; Ø 8 mm; Tmax. 500 C; TÜV-certified Modular flue gas probe incl. cone for fixing; thermocouple NiCr-Ni; hose 2.2 m; dirt filter; length 180 mm; Ø 6 mm; Tmax. 500 C Modular flue gas probe incl. cone for fixing; thermocouple NiCr-Ni; hose 2.2 m; dirt filter; length 300 mm; Ø 6 mm; Tmax. 500 C Flexible flue gas probe incl. cone for fixing; thermocouple NiCr-Ni; hose 2.2 m; dirt filter; length 330 mm; Tmax. 180 C, short-term 200 C, bending radius max. 90 for measurements in difficult to access locations Probe accessories Modular probe shaft; 180 mm; Ø 8 mm; Tmax. 500 C Modular probe shaft; 300 mm; Ø 8 mm; Tmax. 500 C Probe shaft length 335 mm, incl. cone, Ø 8 mm, Tmax 1000 C Flexible probe shaft; 330 mm; Ø 10 mm; Tmax. 180 C Multi-hole probe shaft; length 300 mm; Ø 8 mm; for CO mean value calculation Multi-hole probe shaft; length 180 mm; Ø 8 mm; for CO mean value calculation Hose extension; 2.8 m; extension line probe-instrument Combustion air temperature probe Combustion air temperature probe, immersion depth 300 mm Combustion air temperature probe, immersion depth 190 mm Combustion air temperature probe, immersion depth 60 mm

15 Flue gas testo 320/testo

16 Particulate matter testo 380 Particulate matter analyzer testo 380 In combination with testo LL, the innovative complete solution for solid fuel, oil and gas systems Unrestricted TÜV testing for the limit value levels 1/2 and according to VDI 4206 Sheet 2 Parallel measurement of particulate matter, O 2 and CO Graphic display of all measuring values in real time Particularly cost-effective operation and maintenance Effortless handling and easy transport High-tech in a portable case: Measurement of all relevant values with just one probe testo 380, fine particle analyzer Without flue gas analyzer testo LL (a firmware update allows you to use your existing testo LL from version 2006) The particulate matter measurement system testo 380 allows you to take effortless and straightforward measurements directly on site includes a reading diagram. The completely new method of measurement developed by Testo enables the flue gas inspector/chimney sweep to monitor and enforce the limit values; The heating engineer has a handy measurement system which is the perfect aid to optimising combustion systems for minimum emissions. The particulate matter analyzer testo 380 is especially flexible in its use due to the integration of the testo LL as control centre in the particulate matter measurement system: Just one measurement system can be used to check and service not only solid fuel systems, but also gas and oil systems. testo 380 particulate matter measuring system testo 380 particulate matter analyzer incl. particulate matter probe and cleaning set Flue gas analyzer testo LL with mains unit (incl. bluetooth, H 2 compensated CO cell) Modular flue gas probe 300 mm Combustion air temperature probe, 190 mm testo LL flue gas analyzer Bluetooth testo LL flue gas analyzer set with long life gas sensors; BLUETOOTH and H 2 compensated CO cell, and integrated draught and gas zeroing, incl. rechargeable battery and calibration protocol with display testo 380 accessories testo 606-2, handy wood and material moisture measuring instrument with integrated moisture measurement and NTC ambient thermometer, incl. protective cap, calibration protocol and batteries Combustion air temperature probe, immersion depth 190 mm CO monitor testo incl. case with belt clip, headphones, wrist strap, scanner and calibration protocol Testo fast printer with wireless infrared interface, 1 roll of thermal paper and 4 AA batteries testo BLUETOOTH Printer with wireless bluetooth interface, incl. 1 roll of thermal paper, rech. battery and mains unit Spare thermal paper for printer, permanent ink PC analysis software easyheat, for presenting measurement procedures as diagrams, tabels and for customer data management. USB connection cable instrument/pc, length 2 m Spare parts for testo 380 Spare particulate matter sensor module Spare nozzle Spare dirt filter, 20 pack Probe fixing chain Probe cleaning brush

17 Particulate matter testo 380 Particulate matter case for easy transportation of the particulate matter measurement system. The entire measuring technology is stored in the handy case with a weight of just 7.9 kg. Particulate matter probe changes part of the crude gas into measurement gas. System contamination is kept to a minimum and at the same time accurate measurement is guaranteed. The innovative technology makes the particulate matter probe compact and easy to handle. testo LL flue gas analyzer (as of version 2006) The system control centre measures particulate matter in parallel to CO, O 2 and other flue gas parameters. The handheld instrument can be removed from the case with one handle and used for flue gas analysis of oil and gas systems. Condensate trap and filters The condensate trap and several filters prepare the crude gas for flue gas analysis in the testo LL. Particulate matter sensor Testo has succeeded in making particulate matter measurement easy by using sophisticated sensor technology. The particulate matter values are displayed in real time allowing the effects of every single action on the boiler to be followed immediately. Printer (available as an optional extra) for on site documentation Mains unit for testo LL 17

18 Pressure testo 324/testo 510 Pressure and leakage measuring instrument testo 324 All measurements for gas and water pipes in one instrument Simple menu structure Integrated pressure build up to 300 mbar High precision sensors 2 year warranty Basic testo 324 set: ready to measure for all legally required tests testo 324 leakage measuring instrument, mains unit, system case, incl. feed unit, terminal block* with connection hose, manual pump to set the test pressure, adapter for the gas boiler test port, 3/4 and 1 1/4 high pressure stage stoppers The testo 324 is the perfect measuring instrument for all stress, leakage and serviceability tests on gas and water systems. A flowmeter, absolute pressure sensor and two pressure sensors provide for highly accurate measurement results. Developed specially for professional applications in everyday work, all relevant elements for the measurement are combined in one instrument. By feeding gas instead of air into the system, development of a dangerous gas-air mixture is also prevented. The testo 324 is DVGW-G-5952 tested. * Instrument, pump, and hose connections, incl. overpressure valve and stopcock Professional set testo 324: Professional measurement, documentation and testing testo 324 leakage measuring instrument, mains unit for testo 324 and basic printer, system case, incl. feed unit, terminal block* with connection hose, manual test pump to set the test pressure, adapter for the gas boiler test port, 3/4" and 1 1/4" high pressure stage stoppers, 3/8" and 3/4" high pressure stage stoppers, 1/2" and 1" high pressure stage stoppers, 1/2" and 3/4" tapered test stoppers, testo gas leak detector, infrared basic printer (incl. batteries), and spare printer paper Leakage measurement Measuring range: 0 to 10 l/h Accuracy: ±0.2 l/h or ±5% of m.v Pressure measurement Measuring range: 0 to 1000 hpa Accuracy: ±0.5 hpa or ±3% of m.v. Absolute pressure measurement Measuring range: 600 to 1150 hpa Accuracy: ± 3 hpa Measuring instrument and accessories Overload Temp.measurement TC type K (only instrument) Temp.measurement NTC Type 5k (instrument only) to 1200 hpa Measuring range: -40 to +600 C Accuracy: ± 0.5 C or ± 0.5% Measuring range: -20 to +100 C testo 324 pressure and leakage measuring instrument (without mains unit) Optional bluetooth Wireless transmission Bluetooth retrofitting testo 510 differential pressure measuring instrument Differential pressure measurement 0 to 100 hpa Flow measurement with Pitot tube possible Temperature and air tightness compensation testo 510 testo 510, handy differential pressure measuring instrument, incl. protective cap, calibration protocol, belt pouch and batteries Measuring range Accuracy ±1 digit Resolution Overpressure 0 to 100 hpa ±0.03 hpa (0 to 0.30 hpa) ±0.05 hpa (0.31 to 1.00 hpa) ±(0.1 hpa + 1.5% of m.v.) (1.01 to 100 hpa) 0.01 hpa 500 mbar 18

19 Leak detection testo 316-1/testo 316-2/testo Detector for gas pipe leaks testo Flexible probe for inaccessible areas TopSafe protective cover protects against dirt and impact (optional) Acoustic and visual alarm if limit values are exceeded Methane testo testo electronic gas leak detector with flexible probe, incl. battery Measuring range 0 to 10,000 ppm CH 4 Lower response thresholds 100 ppm 1st Alarm threshold from 200 ppm CH 4 (Yellow LED) 2nd Alarm threshold from 10,000 ppm CH 4 (LED red) Gas leak detector with integrated pump testo Optical and audible alarm thanks to bar display of increasing and dangerous gas concentrations Trend display indicates maximum leakages Integrated pump Flexible probe for inaccessible areas Earplug connection for safe leakage detection in loud surroundings testo Electronic gas leak detector with flexible probe, incl. mains charger and earphones Methane Propane Hydrogen Measuring range 10 ppm to 4.0 vol. % CH 4 10 ppm to 1.9 vol. % C 3 H 8 Lower response thresholds 10 ppm 10 ppm 10 ppm to 4.0 vol. % H 2 10 ppm 1st Alarm threshold 200 ppm CH ppm C 3 H ppm H 2 2nd Alarm threshold 10,000 ppm CH 4 5,000 ppm C 3 H 8 10,000 ppm H 2 Handy gas leak detector for beginners testo Visial bar indicator Self-test of sensor after switching on Pitch of alarm rises along with gas concentration Continuous tone if alarm threshold exceeded testo Gas leak detector, incl. case with belt clip, wrist strap and batteries Methane Propane Measuring range 0 to 20,000 ppm CH 4 0 to 10,000 C 3 H 8 Lower response thresholds 100 ppm CH 4 50 C 3 H 8 1st Alarm threshold 10,000 ppm CH 4 (20% LEL) 5,000 C 3 H 8 (20% LEL) 19

20 Thermography testo 870 Thermal imager testo 870 Ideal thermal imager for tradesmen Small, light (500 g) and robust Easy operation switch on and go Pays off after only a few uses With real image digital camera for documentation (only testo 870-2) testo Thermal imager testo including professional software, USB cable, mains unit and rechargeable Li-ion battery Thermal imager testo 870 was specially developed for your requirements with specialists from the areas of heating engineering, the construction trade, maintenance and facility management. Thanks to its large display, the high quality detector and wide field of vision, it is well suited to localising leaks in interior spaces or revealing thermal bridges in parts of building. testo Thermal imager testo with integrated real image digital camera in a robust case, including professional software, USB cable, mains unit and rechargeable Li-ion battery Infrared resolution Lens pixels 34 26, 3.68 mrad Thermal sensitivity (NETD) < 100 mk at + 30 C Temperature range -20 to +280 C Digital camera resolution (only testo 870-2) Focus 3.1 MP Fixed focus Display 3.5" Memory Internal Accessories Case for testo 870 and additional rechargeable battery. Made from hard wearing nylon with removable shoulder strap, and a strap for attachment to a belt. High-quality transport case Additional battery. Additional lithium ion rechargeable battery for extending the operating time. Battery charging station. Table charging station for optimising the charge time. testo osuperresolution. Four times as many readings, for even more detailed thermal images

21 Thermography testo 875i Thermal imager testo 875i Thermal imager for complete building analysis Exchangeable lenses Measurement mode for detecting areas with danger of mould Connectible wireless humidity probe (optional) Laser marker The thermal imager testo 875i quickly and reliably detects anomalies and weak spots in materials and components. Its 50 mk thermal resolution and exchangeable lenses makes it ideal for analysing complete house façades. testo 875-1i Thermal imager testo 875-1i in a robust case, including pro software, soft case, carrying strap, SD-card, USB cable, lens cleaning cloth, mains unit, Li-ion rechargeable battery and tripod adapter V1 testo 875-2i Thermal imager testo 875-2i in a robust case incl. pro software, soft case, carrying strap, SD card, USB cable, lens cleaning cloth, mains unit, Li ion rechargeable battery, tripod adapter, and headset V2 Infrared resolution Lens pixels Standard: 32 23, 3.3 mrad Tele (optional): 9 7, 1.0 mrad Thermal sensitivity (NETD) < 50 mk at + 30 C Temperature range -20 to +350 C Digital camera resolution Focus 0.3 MP Display 3.5" Manual focus testo 875-2i set Thermal imager testo 875-2i set in a robust case, incl. pro software, soft case, carrying strap, SD card, USB cable, lens cleaning cloth, mains unit, Li ion rechargeable battery, tripod adapter, headset, 9 7 telephoto lens, lens protector, additional battery and quick charging station V3 Memory Exchangeable SD card Accessories testo SuperResolution. Four times as many readings, for even more detailed thermal images. Fast battery charger. Desktop charging station for two rechargeable batteries for the optimization of the charging time Additional battery. Additional Lithiun ion rechargeable battery for extending the operating time Lens protection glass. Special Germanium protective glass for optimum protection of the lens from dust and scratching Telephoto lens (only for testo 875-2i) High temperature measurement up to 550 C (testo 875-2i only) Code 1) (Initial equipment testo 875i) S1 E1 D1 C1 A1 G1 (Retro-fit) ) 2) Humidity measurement with wireless humidity probe* (testo 875-2i only) 1) When ordering as initial equipment, the accessories will already be in the case. Example: testo 875-1i incl. lens protector and spare battery: V1 C1 D1 2) Please contact our customer service 3) Plus installation B1 2) 3) 21

22 Thermography testo 885 Thermal imager testo 885 Thermal imager for highest requirements Exchangeable lenses Parallax-free laser Panorama image assistant for large images Swivel and hinged display for top ergonomics testo Thermal imager testo in a robust case, including pro software, SD card, USB cable, carrying strap, lenscleaning cloth, mains unit, Li ion rech. battery and headset V2 The thermal imager testo 885 is the professional measuring instrument for accurate and non-contact detection of anomalies and weak spots in materials and components. The high quality infrared measurement system allows even the smallest of energy losses and thermal bridges to be visualised. The camera is operated intuitively and features a rotating handle, swivel display and many helpful functions, such as the panorama image assistant, or auto-focus. This not only enables you to carry out fast inspections on site, but also in-depth inspections with professional reports. testo set Thermal imager testo set in a robust case, including pro software, SD card, USB cable, carrying strap, lens-cleaning cloth, mains unit, Li ion rech. battery, headset, telephoto lens, lens case, lens protector, additional rech. battery and fast charging station V3 Infrared resolution pixels Lens Standard: 30 23, 1.7 mrad Tele (optional): 9 7, 1.0 mrad Thermal sensitivity (NETD) < 30 mk at + 30 C Temperature range -20 to +100 C 0 to +350 C (switchable) Digital camera resolution 3.1 MP Focus Display Memory Auto-focus and manual focus 4.3" capacitive LCD touchscreen Swivel and hinged display Exchangeable SD card Accessories testo SuperResolution. Four times as many readings, for even more detailed thermal images. Lens protection glass. Special Germanium protective glass for optimum protection of the lens from dust and scratching Additional battery. Additional Lithium ion rechargeable battery for extending the operating time. Fast battery charger. Desktop charging station for two rechargeable batteries for optimising the charging time. High temperature measurement up to C Humidity measurement with wireless humidity probe* Telephoto lens 11 9 Process analysis package: image sequence capturing in instrument and fully radiometric video measurement 1) When ordering as initial equipment, the accessories will already be in the case. Example: testo incl. lens protection glass and SuperResolution: V1 F1 S1 2) Please contact our customer service 3) Plus installation Code 1) (First equipment) S1 F1 G1 H1 I1 E1 D1 V1 (Retro-fit) ) 2) 3) 2)

23 Temperature testo 925/testo 922 Temperature measuring instruments testo 925/ testo 922 Ideal for application in heating, air conditioning and ventilation areas With optional radio probes Display of differential temperature (testo 922) testo 925 testo 925, 1 channel temperature measuring instrument TE Type K, acoustic alarm, an optional connectible radio probe, incl. calibration protocol and batteries Measuring range Accuracy ±1 digit Resolution -50 to C ±(0.5 C +0.3% of m.v.) (-40 to +900 C) ±(0.7 C +0.5% of m.v.) (rem. meas. range) 0.1 C (-50 to C) ±1 C (remaining meas. range) testo 922 testo 922, 2 channel temperature measuring instrument TE Type K, an optional connectible radio probe, incl. calibration protocol and batteries Probe Robust air probe, TE type K, fixed cable extends to 1.2 m Dimensions Probe shaft/probe shaft tip 115 mm Measuring range Accuracy t to +400 C Class 2 1) 25 sec Ø 4 mm Waterproof immersion/penetration probe, TE type K, fixed cable extends to 1.2 m 114 mm 50 mm Ø 5 mm Ø 3.7 mm -60 to +400 C Class 2 1) 7 sec Super quick-action surface probe with sprung thermocouple strip, also suitable for non-plane surfaces, measuring range briefly up to +500 C, TC Type K, fixed cable extends to 1.2 m 115 mm Ø 5 mm Ø 12 mm -60 to +300 C Class 2 1) 3 sec Pipe wrap probe for pipe diameters 5 to 65 mm, with replaceable measuring head, measuring range briefly up to +280 C, TC type K, fixed cable extends -60 to +130 C Class 2 1) 5 sec Clamp probe for measuring pipes, pipe diameter 15 to 25 mm (max. 1"), measuring range briefly up to +130 C, TE type K, fixed cable extends -50 to +100 C Class 2 1) 5 sec The measuring instrument with this probe is waterproof in the TopSafe. 1) According to standard EN , the accuracy of Class 1 refers to -40 to C (Type K), Class 2 to -40 to C (Type K), Class 3 to -200 to +40 C (Type K). A probe only ever complies with one accuracy class. 23

24 Temperature testo 905/testo 810 Penetration/surface temperature measuring instrument testo 905 Measuring values easy to read thanks to swivel display Very fast response time Easy to operate testo 905-T1 testo 905-T1, penetration thermometer, large measuring range up to 350 C, great accuracy, incl. attachment clip and batteries testo 905-T2 testo 905-T2, surface thermometer with crossband probe, extremely fast response time, great accuracy, incl. attachment clip and batteries Infrared temperature measuring instrument (2 channel) testo 810 Convenient pocket-sized combined instrument for noncontact measurement of the surface temperature and measurement of the air temperature 1-point laser measurement spot marking and 6:1 lens Hold function, display of max./min. values and the difference between air and surface temperatures testo 810 testo 810, 2 channel temperature measuring instrument with infrared thermometer, laser measurement spot marking, integrated NTC ambient thermometer, incl. protective cap, calibration protocol, belt bag and batteries Infrared NTC Measuring range -30 to +300 C -10 to +50 C Accuracy ±1 digit ±2.0 C (-30 to +100 C) ±2% of m.v. (remaining meas. range) ± 0.5 C Measurement rate 0.5 sec 0.5 sec Resolution 0.1 C 0.1 C 24

25 Temperature testo 830/testo 835-H1 Infrared temperature measuring instruments testo 830 Laser measurement spot marking and large lenses for accurate measurement, even at greater distances Adjustable emission factor Two adjustable alarm limit values Hold function and display of min./max. values testo 830-T1 testo 830-T1, infrared thermometer, 1 point laser measurement spot marking, 10:1 lens, adjustable limit values, alarm function, incl. batteries and factory calibration certificate testo 830-T1 testo 830-T4 Measuring range Infrared -30 to +400 C -30 to +400 C Type K (NiCr-Ni) -50 to +500 C Accuracy ±1 digit Infrared ±1.5 C or 1.5% of m.v. (+0.1 to +400 C) ±2 C or ±2% of m.v. (-30 to 0 C) the higher value applies ±1.5 C (-20 to 0 C) ±2 C (-30 to C) ±1 C or 1% of m.v. (remaining meas. range) Type K (NiCr-Ni) ±0.5 C +0.5% of m.v. Resolution 0.1 C 0.1 C testo 830-T4 testo 830-T1, infrared thermometer, 2-point laser measurement spot marking, 30:1 lens, adjustable limit values, alarm function, external probe can be connected, incl. batteries and factory calibration certificate Probe for testo 830; see probes for testo 925/testo 922 on page 23. Infrared thermometer with humidity module testo 835-H1 Patented surface moisture measurement to identify areas at risk of mould 4-point laser shows the exact measuring range, preventing incorrect measurements Integrated emission level measurement for absolute measurement certainty Convenient menu guidance with icons and joystick testo 835-H1 testo 835-H1, infrared temperature measuring instrument, 4-point laser marker, measurement data management, PCsoftware, humidity module, incl. batteries and calibration protocol Measuring range Infrared -30 to +600 C Type K (NiCr-Ni) -50 to +600 C Humidity sensor 0 to 100% RH Accuracy ±1 digit Infrared Type K (NiCr-Ni) Humidity sensor Resolution ±2.5 C (-30.0 to C) ±1.5 C (-20.0 to -0.1 C) ±1.0 C (+0.0 to C) ±1% of m.v. (remaining meas. range) ±(-0.5 C +0.5% of m.v.) ±2% RH ± 0.5 C 0.1 C/0.1% RH/0.1 Ctd Probe for testo 835-H1; see probes for testo 925/testo 922 on page

26 Humidity testo 605-H1/testo 608-H2/testo 610/testo 625 Humidity/temperature measuring instrument testo 605-H1 Accurate measurement of humidity, air temperature and dew point Ideal for measurements in ducts Measuring values easy to read thanks to hinged joint testo 605-H1 testo 605-H1, thermo-hygrometer with duct bracket and dew point calculation, incl. attachment clip and batteries Measuring range 0 to +50 C/-20 to +50 Ctd / 5 to 95% RH Accuracy ±1 digit ±0.5 C/ ±3% RH Resolution 0.1 C/0.1% RH Thermohygrometer testo 608-H2 Continuous display of temperature and humidity/dew point Min./max. values Battery monitor testo 608-H2 testo 608-H2, alarm hygrometer, humidity/ dew point/temperature measuring instrument with LED alarm, incl. calibration protocol and battery Measuring range Accuracy ±1 digit Resolution -10 to +70 C / -40 to +70 Ctd / +2 to +98% RH ±0.5 C (at +25 C) / ±2% RH (+2 to +98% RH) 0.1 C/0.1% RH Humidity/temperature measuring instrument testo 610 Measurement of air humidity and temperature Includes dew point calculation and wet bulb Testo humidity sensor with long-term stability testo 610 testo 610, handy humidity/temperature measuring instrument, incl. protective cap, calibration protocol, belt pouch and batteries Measuring range Accuracy ±1 digit Resolution -10 to +50 C/0 to 100% RH 0.5 C/ ±2.5% RH (5 to 95% RH) 0.1 C/0.1% RH Humidity/temperature measuring instrument testo 625 Display of temperature and relative humidity/wet bulb temperature and dew point Min./max. values Display lighting testo 625 testo 625, humidity/temperature measuring instrument, incl. plug-in humidity probe head, calibration protocol and battery Measuring range Accuracy ±1 digit Resolution 26 0 to +100% RH/-10 to +60 C ±2.5% RH (+5 to +95% RH)/±0.5 C 0.1% RH/0.1 C

27 Humidity testo 635 Humidity/temperature measuring instrument testo 635 Connection of 2 plug-in probes and 3 radio probes for temperature and humidity Measurement of temperature, humidity, material equilibrium moisture content, pressure dew point, absolute pressure and U-value Display of dew point interval, min, max and mean values Print-out of data using the Testo fast printer (optional) Illuminated display Protection class IP 54 testo testo 635-1, humidity/temperature measuring instrument, incl. calibration protocol and batteries testo testo 635-2, humidity/temperature measuring instrument with reading memory, PC software, USB data cable, incl. calibration protocol and batteries Type K (NiCr-Ni) NTC (humidity probe) Testo humidity sensor Absolute pressure probe Measuring range -200 to C -40 to +150 C 0 to +100% RH 0 to 2000 hpa Accuracy ±1 digit ±0.5 C (-60 to +60 C) ±(0.2 C + 0.3% of m.v.) (remaining meas. range) ±0.2 C (-25 to C) ±0.4 C (-40 to C) ±0.4 C (+75 to C) ±0.5% of m.v. (rem. meas. range) See probe data Resolution 0.1 C 0.1 C 0.1% RH 0.1 hpa See probe data Accessories Service case for basic equipment of measuring instrument and probes, dimensions mm Testo fast printer with wireless infrared interface, 1 roll of thermal paper and 4 AA batteries Probe Dimensions Probe shaft/probe shaft tip Measuring range Accuracy t 99 Humidity/temperature probes Ø 12 mm 0 to +100% RH -20 to +70 C ±2% RH (+2 to +98% RH) ± 0.3 C Slim humidity probe with offset electronics, incl. 4 plug-on PTFE protective caps for material equilibrium moisture measurement 60 mm Ø 4 mm 0 to +100% RH 0 to +40 C ±2% RH (+2 to +98% RH) ± 0.2 C Scatter field probe for fast and non-destructive material moisture measurement, with 1.2 m probe cable Robust air probe, TE type K, fixed cable extends Woods: <50% Building materials: <20% mm -60 to +400 C Class 2 1) 25 sec Temperature probe for U-value determination, threefold sensor for recording wall temperature, incl. modelling clay -20 to +70 C Class 1 1) U-value: ±0.1 C ±2% of m.v. * Note: this probe only fits on testo To determine the U-value an additional probe is required to record the ambient temperature, e.g or / * for use with NTC or humidity radio probes for measuring ambient temperature and 20 K difference in air inside/outside ) According to standard EN , the accuracy of Class 1 refers to -40 to C (Type K), Class 2 to -40 to C (Type K), Class 3 to -200 to +40 C (Type K). 27

28 Humidity testo 606/testo 616 Wood/material moisture measuring instrument testo 606 Other characteristics for detecting wet areas in construction materials Display lighting Additional advantages of the testo Measurement of temperature and humidity in ambient air Includes dew point calculation and wet bulb Measuring range Accuracy ±1 digit testo 606-1/-2 testo Material moisture NTC Humidity sensor 0 to 50% -10 to +50 C 0 to 100% RH 1% ± 0.5 C ±2.5% RH (5 to 95% RH) Resolution C 0.1% RH testo testo 606-1, handy wood/material moisture measuring instrument, incl. protective cap, calibration protocol, belt pouch and batteries testo testo 606-2, handy wood and material moisture measuring instrument with integrated moisture measurement and NTC air thermometer, incl. protective cap, calibration protocol, belt pouch and batteries Material humidity measuring instrument testo 616 Accurate measurement of moisture in construction materials and woods Equipped with 10 characteristics Handy shape for optimal contact pressure testo 616 testo 616, material moisture measuring instrument for non-destructive moisture measurement of wood and construction materials, incl. calibration protocol and battery Measuring range wood: <50% Measuring range building materials: <20% Resolution

29 Humidity testo 174-H/testo 175 H1 Mini data logger for temperature and humidity testo 174H Long-term stable humidity sensor Display of current temperature or humidity values Quick data evaluation and documentation on the PC testo 174H Mini data logger testo 174H, 2 channel, incl. wall bracket, batteries (2 CR 2032 lithium) and calibration protocol Measuring range Accuracy ±1 digit Resolution -20 to +70 C 0 to 100% RH* ±0.5 C (-20 to +70 C) ±2% RH (3 to 98% RH) ±0.03% RH/K 0.1 C 0.1% RH * Not for condensing atmospheres. For continuous application in high humidity (>80% RH at 30 C for >12 h, >60% RH at >30 C for >12 h), please contact us via our website. Set testo 174H Mini data logger set testo 174H 2 channel, incl. USB interface for programming and reading out the logger, wall bracket, batteries (2 CR 2032 lithium) and calibration protocol Accessories USB interface for programming and reading out the loggers testo 174T and testo 174H ComSoft Basic, basic software for programming and reading out Testo data loggers; display of measured values in graph and chart form, and export function. (If free download (requiring registration) is not required) ComSoft Professional, professional software, incl. data archiving Mini data logger for temperature and humidity testo 175 H1 Large, easy-to-read display Measurement data memory for 1 million readings Up to 3 years battery standby Permanently connected capacitive humidity sensor testo 175 H1 testo 175 H1, 2-channel temperature and humidity data logger with external humidity sensor (NTC/capacitive humidity sensor) incl. wall bracket, lock, batteries and calibration protocol Accessories Wall bracket (black) with lock for testo 175 Cable for connecting the data loggers testo 175 and testo 176 with a PC, mini USB to USB SD card for collecting the measurement data from the data loggers testo 175 and testo 176, 2 GB, application range to -20 C Battery for testo 175 Application range -10 C, alkaline manganese batteries AAA (please order 3 batteries per logger) ComSoft Basic, basic software for programming and reading out Testo data loggers; display of measured values in graph and chart form, and export function. (If free download (requiring registration) is not required) ComSoft Professional, professional software, incl. data archiving Measuring range Accuracy ±1 digit Resolution -20 to +55 C -40 to +50 C td 0 to 100% RH* ±0.4 C (-20 to +55 C) +0.03% RH/K ±2% RH (+2 to 98% RH) at +25 C 0.1 C 0.1% RH * Not for condensing atmospheres. For continuous application in high humidity (>80% RH at 30 C for >12 h, >60% RH at >30 C for >12 h), please contact us via our website. 29

30 Flow testo 405/testo 425 Thermal anemometer testo 405 Flow measuring instrument with temperature measurement Volumetric flow rate calculation to m³/h Extendible telescope to 300 mm testo 405 testo 405, thermo-anemometer with duct bracket, incl. attachment clip and batteries Thermal NTC Measuring range Accuracy ±1 digit 0 to 5 m/s (-20 to 0 C) 0 to 10 m/s (0 to +50 C) 0 to m³/h ±(0.1 m/s + 5% of m.v.) (0 to +2 m/s) ±(0.3 m/s + 5% of m.v.) (remaining meas. range) -20 to +50 C ± 0.5 C Resolution 0.01 m/s 0.1 C Thermal anemometer testo 425 Measurement of flow, volumetric flow and temperature Single-point and multi-point mean calculation Max./min. values testo 425 testo 425, compact thermal anemometer with permanently connected flow probe, incl. temperature measurement and telescope (max. 820 mm), calibration protocol and battery Thermal NTC Measuring range Accuracy ±1 digit 0 to +20 m/s -20 to +50 C ±(0.03 m/s +5% of m.v.) ±0.5 C (0 to +60 C) ±0.7 C (remaining meas. range) Resolution 0.01 m/s 0.1 C 30

31 Flow testo 410/testo 416/testo 417 Vane anemometer testo 410 Flow measuring instrument with temperature measurement Integrating measurement by 40 mm vane Additional advantages of the testo Humidity measurement with Testo humidity sensor with long-term stability testo testo 410-1, vane anemometer with integrated NTC air thermometer, incl. protective cap, calibration protocol and batteries Measuring range Accuracy ±1 digit testo 410-1/-2 testo Vane NTC Humidity sensor 0.4 to 20 m/s -10 to +50 C 0 to 100% RH ±(0.2 m/s + 2% of m.v.) ± 0.5 C ±2.5% RH (5 to 95% RH) Resolution 0.1 m/s 0.1 C 0.1% RH testo testo 410-2, vane anemometer with integrated humidity measurement and NTC air thermometer, incl. protective cap, calibration protocol and batteries Vane anemometer testo 416 Direct display of the volumetric flow Single-point and multi-point mean calculation Hold button to record the reading testo 416 testo 416, vane anemometer with permanently connected 16 mm telescopic vane (max. 890 mm), incl. calibration protocol and battery Measuring range Accuracy ±1 digit 0.6 m/s to 40 m/s ±(0.2 m/s +1.5% of m.v.) Resolution 0.1 m/s Vane anemometer testo 417 Measurement of flow, volumetric flow and temperature Flow direction detection Single-point and multi-point mean calculation testo 417 testo 417, vane anemometer with integrated 100 mm vane, incl. temperature measurement, calibration protocol and battery Measuring range Accuracy ±1 digit NTC Vane Volumetric flow 0 to +50 C +0.3 to +20 m/s ± 0.5 C ±(0.1 m/s +1.5% of m.v.) 0 to m³/h Resolution 0.1 C 0.01 m/s 0.1 m³/h (0 to m³/h) 1 m³/h (+100 to m³/h) Accessories testovent 417, funnel set comprising funnel for disc valves (Ø 200 mm) and funnel for fans ( mm) for supply and exhaust air Volumetric flow rectifier testovent 417 comprising the testovent 417 funnel set and volumetric flow rectifier

32 Multi-function testo 435 Multi-functional measuring instrument testo 435 Large range of probes (optional): - IAQ probe for evaluating indoor air quality - Thermal probes with integrated measurement of temperature and humidity - Vane and hot wire probes - Integrated differential pressure probe for Pitot tube measurement (see variants) - Radio probe for temperature and humidity (see variants) Easy operation PC software for analyzing, archiving and documenting the readings testo testo 435-1, multi-functional measuring instrument for air conditioning, ventilation and indoor air quality, incl. calibration protocol and batteries testo testo 435-4, multi-functional measuring instrument with integrated differential pressure measurement for air conditioning, ventilation and indoor air quality, reading memory, PC software, USB cable, incl. calibration protocol and batteries The multi-functional measuring instrument testo 435 is your reliable partner for indoor air analysis, and for regulating VAC systems to optimise energy use. To evaluate indoor air quality CO 2, relative humidity and room temperature parameters are available. In addition, the absolute pressure, draught, lux, U-value and surface temperature can be defined. To determine the volumetric flow all the options for flow measurement are available to you - e.g. thermal probes, vanes and Pitot tubes. Application image: testo 435 testo testo Connectible probe (optional) IAQ probe for measuring CO 2, air temperature, indoor humidity and absolute pressure X X Thermal flow probe with integrated temperature and humidity measurement X X Vane and hot wire probes X X Radio probe for temperature measurements X X Ambient CO probe X X Absolute pressure probe X X Integrated differential pressure measurement for measuring flow with Pitot tubes and filter monitoring X Comfort probe for measuring turbulence levels X Humidity probe for air temperature and humidity measurements X Radio probe for air temperature and humidity measurements X Lux probe for measuring luminous flux X Temperature probe for U-value recording X Instrument fittings Easy operation with user profiles X X Illuminated display X X Testo fast printer for documenting measurement data (optional) X X Instrument memory for readings (cannot be retrofitted) X PC software for analyzing, archiving and documenting the readings X 32

33 Multi-function testo 435 Probe Dimensions Probe shaft/probe shaft tip Measuring range Accuracy IAQ probe for the evaluation of indoor air quality, CO 2, humidity, temperature and absolute pressure measurement, incl. desktop tripod 0 to +50 C 0 to +100% RH 0 to ppm CO to hpa ± 0.3 C ±2% RH (+2 to +98% RH) ±(75 ppm CO 2 ±3% of m.v.) (0 to ppm CO 2 ) ±(150 ppm CO 2 ±5% of m.v.) (+5001 to ppm CO 2 ) ± 10 hpa Thermal flow probe with integrated temperature and humidity measurement, Ø 12 mm, with telescope (max. 745 mm) -20 to +70 C 0 to +100% RH 0 to +20 m/s ± 0.3 C ±2% RH (+2 to +98% RH) ±(0.03 m/s +4% of m.v.) Vane measuring probe, 16 mm diameter, with telescope of max. 890 mm, e.g. for duct measurement, can be used from 0 to +60 C +0.6 to +40 m/s Operating temperature 0 to +60 C ±(0.2 m/s +1.5% of m.v.) Vane measuring probe, 60 mm diameter, with telescope of max. 910 mm, e.g. for duct outlet measurement, can be used from 0 to +60 C to +20 m/s Operating temperature 0 to +60 C ±(0.1 m/s +1.5% of m.v.) Hot wire probe for m/s and C, Ø 7.5 mm probe head, incl. telescope (max. 820 mm) 0 to +20 m/s -20 to +70 C ±(0.03 m/s +5% of m.v.) ±0.3 C (-20 to +70 C) Vane measuring probe, 100 mm diameter, for measuring with funnel set to +20 m/s 0 to +50 C ±(0.1 m/s +1.5% of m.v.) ± 0.5 C testovent 417, funnel set comprising funnel for disc valves (Ø 200 mm) and funnel for fans ( mm) for supply and exhaust air Volumetric flow rectifier testovent Volumetric flow rectifier testovent 417 comprising the testovent 417 funnel set and volumetric flow rectifier testovent Comfort probe for degree of turbulence measurement with telescope (max. 820 mm) and tripod, fulfils requirements of EN max. 820 mm 0 to +50 C 0 to +5 m/s ± 0.3 C ±(0.03 m/s +4% of m.v.) Lux probe; probe for measuring luminous flux 0 to 100,000 Lux 0 to 300 Hz Accuracy as per DIN : f1 = 6% = V(Lambda) adjustment f2 = 5% = cos-like weighting Class C Humidity/temperature probes -20 to +70 C 0 to +100% RH ± 0.3 C ±2% RH (+2 to +98% RH) Ø 12 mm Temperature probe for U-value determination, threefold sensor for recording wall temperature, incl. modelling clay -20 to +70 C Class 1 1) U-value: ±0.1 C ±2% of m.v. * Note: To determine the U-value an additional probe is required to record the ambient temperature, e.g or / * for use with NTC or humidity radio probes for measuring ambient temperature and 20 K difference in air inside/outside

34 Indoor air quality testo 315-2/testo 317-3/testo 317-1/testo 535 CO warning/measuring instrument testo CO safety warning Adjustable alarm thresholds Automatic zeroing testo testo 315-2, CO warning/measuring instrument, incl. battery and calibration report Measuring range Accuracy ±1 digit Resolution 0 to +2,000 ppm CO ±10 ppm CO (0 to +100 ppm CO) ±10% of m.v. (+100 to +2,000 ppm CO) 1 ppm CO Measuring instrument for CO environment measurements testo testo testo 317-3; CO monitor testo incl. case with belt clip, headphones, wrist strap, scanner and calibration protocol 3-year guarantee on CO sensor No zero phase, instrument ready for use immediately Adjustable alarm thresholds Measuring range Accuracy ±1 digit Resolution 0 to ppm ±3 ppm (0 to +29 ppm) 10% (+30 to ppm) 1 ppm Back pressure indicator for detection of leaking flue gases testo testo testo back pressure indicator with flexible probe, incl. battery Reliable detection of leaking flue gases Flexible probe for inaccessible areas Audible and visual alarm CO 2 measuring instrument testo 535 Highly accurate CO 2 measurement 2-channel infrared sensor with long-term stability Long-term monitoring by means of max. and mean values testo 535 testo 535, CO 2 measuring instrument with permanently connected probe, calibration protocol and battery Measuring range0 to ppm CO 2 Accuracy ±1 digit Resolution ±(75 ppm CO 2 ±+3% of m.v.) (0 to ppm CO 2 ) ±(150 ppm CO 2 ±+5% of m.v.) (+5001 to ppm CO 2 ) 1 ppm CO

35 Sound testo 815/testo Light testo 540 Sound level meter testo 815 Frequency evaluation according to characteristic curve A and C Easy to adjust Memory for maximum and minimum values testo 815 testo 815, sound level meter, incl. screwdriver for calibration, wind protection, and battery Measuring range Frequency range +32 to +130 db 31.5 Hz/ 8 khz Accuracy ±1 digit Resolution ±1.0 db 0.1 db Sub-measuring range 30 to 80 db; 50 to 100 db; 80 to 130 db Time weighting Setting FAST 125 ms/setting SLOW 1 s Pressure dependency: db/hpa Accessories Calibrator for regular calibration of testo 815, testo testo sound level meter testo Sound level metering complying with IEC Class 2 and ANSI S1.4 type 2 Frequency assessment A and C Time evaluation can be changed between fast and slow testo 816-1; sound level meter, incl. microphone, wind protection, PC software, connection cable, instruction manual on CD-ROM and batteries in the system case Measuring range 30 to 130 db Frequency range 20 Hz/ 8 khz Accuracy ±1 digit Resolution ±1.4 db (under reference conditions: 94 db, 1 khz) 0.1 db Accessories Calibrator for regular calibration of testo 815, testo Lux meter testo 540 testo 540 testo 540, handy lux meter, incl. protective cap, calibration protocol, and batteries Sensor adjusted to spectral sensitivity of the eye Hold function and max./min. values Display lighting Measuring range Accuracy ±1 digit Resolution 0 to lux ±3 lux or ±3% of m.v. (compared to reference class B, DIN 5032 part 7) 1 lux (0 to lux) 10 lux (remaining meas. range) 35

36 Videos: How Testo measuring instruments excel in practice. Watch four short and informative application videos to see how installation and heating engineering professionals ensure the energy efficiency of heating systems with our flue gas analyzer, thermal imagers, and leakage measuring instruments. 298X XXXX/dk/I/ Video: Thermography in heating engineering with the testo Video: Serviceability test of a gas pipe with the testo Subject to change, including technical modifications, without notice. Video: Inspection of a heating system with the testo Video: Inspection of a heating system with the testo