NOWASTE: WASTE HEAT RE-USE FOR GREENER TRUCKS

Transcription

1 NOWASTE: WASTE HEAT RE-USE FOR GREENER TRUCKS V. Lemort, L. Guillaume, F. Bettoja, T. Reiche, and T. Wagner EGVIA workshop Brussels, May 31 st 2017

2 Introduction Context ² Reduce fuel consumption is necessary Ø to reduce GHG emissions (HD represents ¼ of EU road transport emissions) Ø to increase competitiveness of transportation by trucks (fuel=28% of the total operating cost of the truck) ² How could we reduce fuel consumption? Ø Waste heat valorization is a promising solution Ø Even with a large engine efficiency, 50-60% of fuel energy is lost in waste heat Typical energy distribution on a euro 5 engine 2

3 Introduction Rankine cycle systems ² Among the WHR techniques, the Rankine cycle is one of the most promising ones. Many possible architectures for given boundary conditions ² However, R&D activities are still necessary to find the most appropriate architecture (working fluid, heat source/sink, expansion machine, etc.) in order to reach an acceptable economical profitability and to increase reliability 3

4 NoWaste project Consortium ² FP7 project ² Duration: 42+6 months / Start: October 2011 ² Coordinator: CRF ² Main partners: 4

5 NoWaste project Objectives and challenges ² Develop and validate 2 ORC-based waste heat recovery systems for HD trucks. ² Challenges of the NoWaste project: Ø New components should be compliant with automotive constraints (weight, cost) Ø System should be compliant with incoming regulations about GHG emissions (e.g. F-gas regulation) Ø Impact on vehicle architecture and performance should be limited (for instance cooling drag, back pressure, etc.) Ø Optimize the energy management system (production/storage/use of energy) 5

6 NoWaste project Project organization Y e a r 1 Y e a r 2 Y e a r 3 WP6 Dissemination 6

7 Content of the presentation 1. Introduction 2. NoWaste project 3. Architectures of ORC systems 4. Experimental characterization of prototypes 5. Economical analysis 6. Conclusions 7

8 Architectures of ORC systems Reference applications VOLVO Renault Truck CRF IVECO Engine: thermal w EGR Engine: thermal w/o EGR 8

9 Architectures of ORC systems CRF application Trade off between impact on overall vehicle efficiency and simplicity/cost/ volume/weight Heat source: Exhaust gas only (no EGR): lower temperature heat source Heat sink: low temperature coolant circuit (60 C, capacity limited to 35 kw) Electrical output power No flammable fluid (security): o R245fa o R1233zd: GWP<5 and potentially better performance 9

10 Architectures of ORC systems CRF application Components: Expander: Axial impulse turbine + reducer + generator: electrical output power Boiler: stainless steel plate-fin heat exchanger Condenser: aluminum plate heat exchanger Internal gear pump 10

11 Architectures of ORC systems CRF application Performance design point

12 Architectures of ORC systems Volvo application More complex system Heat source: o Exhaust gas + EGR cooler (higher temperature heat source) o Series or parallel configuration o Recirculated gas temperature low enough Heat sink: low temperature coolant circuit (60-70 C) Mechanical output power Working fluid: ethanol o Better performance o Water-ethanol mixture (reduced flammability and corrosivity) 12

13 Architectures of ORC systems Volvo application WHR on exhaust gases only WHR on exhaust gases and EGR gases in serial WHR on exhaust gases and EGR gases in parallel Dedicated low temp. radiator Engine coolant circuit Source: V. Grelet, T. Reiche, V. Lemort, M. Nadri, P. Dufour, Transient performance evaluation of waste heat recovery Rankine cycle based system for heavy duty trucks. Applied Energy, In press EGR cooler as preheater (serial configuration of the heat sources) o Lower net power production than serial configuration o But lower complexity and cost (less valves) and better cooling down of EGR gases 13

14 Architectures of ORC systems Volvo application Components: Expander: turbine + reducer + engine mechanical coupling EGR Boiler: brazed stainless steel heat exchanger with a concept similar as the EGR cooler Tailpipe boiler: brazed stainless steel (counter flow) plate heat exchanger Condenser: brazed stainless steel (plate/plate counter flow) heat exchanger External gear pump 14

15 Architectures of ORC systems Components specifications 15

16 Content of the presentation 1. Introduction 2. NoWaste project 3. Architectures of ORC systems 4. Experimental characterization of prototypes 5. Economical analysis 6. Conclusions 16

17 Experimental characterization of prototypes CRF application Tests in steady-state engine regime Purpose: Check suppliers specifications and collect data for simulation models improvement All components operated as envisioned, except the turbine whose efficiency is lower than expected. Includes isentropic, mechanical and electrical efficiencies Includes isentropic efficiency only 17

18 Experimental characterization of prototypes CRF application Measured performance at different engine load levels: 18

19 Experimental characterization of prototypes Volvo application Tests in steady-state engine regime Turbine replaced by a representative orifice. Heat ratio = fraction of heat recovered by the working fluid compared to the total heat loss of EGR and exhaust gases o => indication of ambient losses (15-25% in steady-state) o Insulation would have a non negligible impact on weight and cost Engine torque (N.m) Heat Ratio Boiler (%) Engine speed (rpm)

20 Experimental characterization of prototypes Volvo application Extrapolation of performance with a turbine total efficiency of 65% Engine torque (N.m) ORC eff est(%) Engine speed (rpm) o => average efficiency estimation of 10% over a relatively wide range of engine working points o Performance can be increased by improving components efficiencies and decreasing condensing pressure 20

21 Content of the presentation 1. Introduction 2. NoWaste project 3. Architectures of ORC systems 4. Experimental characterization of prototypes 5. Economical analysis 6. Conclusions 21

22 Economical analysis Production cost breakdown o CRF system Ø Smaller, more reliable, less efficient Ø EUR o Volvo system Ø More complex, more efficient Ø EUR Expander and evaporator are the main drivers of the total cost. 22

23 Economical analysis Return on investment time 23

24 Conclusions Project main achievements Relevant improvement in respect of the understanding of the system design and its integration on a heavy duty vehicle application; Increased motivation of the Industrial OEM involved and of the components suppliers in the investment on specific components development; Demonstrated energy savings realized on the considered engine applications through a waste heat recovery system based on the ORC technology; CRF idea of cheap and plug and play system has a low impact on the vehicle s architecture because of its low global size and weight, and no impact on the powertrain s design, can achieve interesting results in terms of electricity power output (~2 kw). VOLVO s WHR system showed that efficient EGR cooling and heat recovery can be combined for a long haul heavy duty application showing realistic cycle efficiencies around 10% on all measured engine working points. 24

25 Thank you for your attention! 25