SAFETY DATA SHEET ISSUED SEPTEMBER 2014 (VALID 5 YEARS FROM DATE OF ISSUE) Heavy Duty Nozzle Dipping Gel

Transcription

1 SAFETY DATA SHEET ISSUED SEPTEMBER 2014 (VALID 5 YEARS FROM DATE OF ISSUE) CT-WNDG Heavy Duty Nozzle Dipping Gel SDS SECTION 1 - IDENTIFICATION OF THE MATERIAL & COMPANY INFORMATION Chemtools Pty Ltd Phone: (business hours) Unit 2/14-16 Lee Holm Road Fax: St Marys NSW PRODUCT NAME PRODUCT TYPE PART NUMBER AVAILABLE SIZES Heavy Duty Nozzle Dipping Gel Weld Anti-Spatter Coating CT-WNDG-400G SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS HAZARDOUS COMPONENTS CAS # % ACGIH TLV OSHA PEL Petrolatum Hydrated magnesium silicate (2-butoxyethanol) <10 SECTION 3 - HAZARDS IDENTIFICATION Hazard Classification: Relevant Routes of Exposure: Potential Health Effects: Inhalation: Skin Contact: Eye Contact: Ingestion: Not classified as a Hazardous Substance according to the criteria of SafeWork Australia. Non-Dangerous Goods according to the ADG Code. Ingestion Unlikely to cause adverse effects by inhalation Unlikely to cause adverse effects through skin contact Unlikely to cause adverse effects through eye contact Unlikely to cause adverse effects by swallowing HMIS: Health: Reactivity: Flammability: PPE: Warning: No specific hazards under normal use conditions. Prolonged or repeated exposure to skin may give rise to dermatitis. Used grease may contain harmful impurities. SECTION 4 - FIRST AID MEASURES Inhalation: Skin contact: No measures necessary. Obtain medical advice if symptoms persist If skin contact occurs, remove contaminated clothing and wash skin with

2 Material Safety Data Sheet: WNDG Heavy Duty Nozzle Dipping Gel Page 2 Eye contact: Ingestion: running water. If irritation occurs seek medical advice. If contact with hot product occurs, treat as for burns. If contact with the eye(s) occurs, wash with copious amounts of water holding eyelid(s) open. Take care not to rinse contaminated water into the non-affected eye. If symptoms develop and persist seek medical attention. Do NOT induce vomiting. Wash out mouth with water. If symptoms develop and persist, seek medical attention. SECTION 5 - FIRE FIGHTING MEASURES Flash point: 210 C (DIN-ISO 2592). Autoignition Temperature: This product is combustible. This product will burn if exposed to fire Flammable/Explosive Limits - Lower %: N/A Flammable/Explosive Limits - Upper %: N/A Extinguishing Media: Foam, dry powder, Carbon dioxide and sand Special Fire Fighting Procedures: DO NOT USE water jets Unusual Fire or Explosion Hazards: None Hazardous Combustion Products: Under fire conditions this product may emit toxic and/or irritating fumes including carbon monoxide, carbon dioxide, oxides of nitrogen, soot and organic substances Hazchem Code: N/A SECTION 6 - ACCIDENTAL RELEASE MEASURES Environmental Precautions: Clean-up Methods: If large spillages of this material enters the waterways contact the Environmental Protection Authority, or your local Waste Management Authority Risk of slippery surfaces due to spilled product. Allow spilled material to solidify and remove mechanically. Extinguish or remove all sources of ignition and stop leak if safe to do so. Dispose of waste according to federal, Environmental Protection Authority and state regulations. If large spillages of this material enters the waterways contact the Environmental Protection Authority, or your local Waste Management Authority. Use appropriate personal protective equipment during clean-up. SECTION 7 - HANDLING AND STORAGE Handling: No special handling procedures are required. Wash hands thoroughly after handling Storage: Store in a cool, dry well-ventilated area away from heat, sources of ignition, oxidising agents and out of direct sunlight Incompatible products: Refer to Section 10. SECTION 8 - EXPOSURE CONTROLS/PERSONAL PROTECTION Engineering controls: Respiratory protection: Skin protection: Eye/face protection: Exposure Limits: No exposure standards have been established for this material by the National Occupational Health and Safety Commission (NOHSC). However, as with all chemicals, exposure should be kept to the lowest possible levels Not normally required. Gloves are recommended as good industrial practise Safety glasses are recommended as good industrial practise. See Section 2 - Composition/Information on Ingredients SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES

3 Material Safety Data Sheet: WNDG Heavy Duty Nozzle Dipping Gel Page 3 Physical State: Semi Solid (Paste). Colour: White Odour: None Vapour Pressure: ph: N/A Boiling Point/Range: N/A. Melting Point/Range: 40-65ºC Specific Gravity: Approx kg/m³ (DIN ) Vapour Density: <0.01 C Evaporation Rate: N/A Solubility in Water: Insoluble VOC Content: SECTION 10 - STABILITY AND REACTIVITY Stability: Hazardous polymerization: Hazardous decomposition products: Incompatibility: Conditions to avoid: Stable at normal temperatures and conditions. Will not occur. In case of incomplete combustion and/or thermal decomposition carbon monoxide, carbon dioxide, several hydrocarbons and soot may be formed Strong oxidising agents. See Section 7 - Handling and Storage Refer to 'Incompatibility', this section, above SECTION 11 - TOXICOLOGICAL INFORMATION Basis for Assessment: Acute Toxicity Oral Acute Toxicity Dermal Acute Toxicity Inhalation Eye Irritation: Skin Irritation: Respiratory Irritation: Skin Sensitisation: Carcinogenicity: Mutagenicity: Reproductive Toxicity: Other Information: Information given is based on a knowledge of the components and the toxicology of similar products. LD 50 expected to be > 2000 mg/kg. LD 50 expected to be > 2000 mg/kg. Not considered to be an inhalation hazard under normal conditions of use. Not expected to be an irritant. Not expected to be an irritant. If mists are inhaled, slight irritation of the respiratory tract may occur. Not expected to be a skin sensitizer. Components are not known to be associated with carcinogenic effects. Not considered to be a mutagenic hazard. Not considered to be toxic to reproduction. Prolonged and/or repeated contact with products containing mineral oils can result in defatting of the skin, particularly at elevated temperatures. This can lead to irritation and possibly dermatitis, especially under conditions of poor personal hygiene. Skin contact should be minimised. High pressure injection of product into the skin may lead to local necrosis if the product is not surgically removed. Used grease may contain harmful impurities that have accumulated during use. The concentration of such harmful impurities will depend on use and they may present risks to health and the environment on disposal. ALL used grease should be handled with caution and skin contact avoided as far as possible. SECTION 12 - ECOLOGICAL INFORMATION Ecotoxicological data have not been determined specifically for this product. Information given is based on a knowledge of the components and the ecotoxicology of similar products. Mobility: Semi-solid under most environmental conditions. Floats on water. If it enters soil, it will adsorb to soil particles and will not be mobile.

4 Material Safety Data Sheet: WNDG Heavy Duty Nozzle Dipping Gel Page 4 Persistence / Degradability: Bioaccumulation: Ecotoxicity: Other Adverse Effects: Not expected to be readily biodegradable. Major constituents are expected to be inherently biodegradable, but the product contains components that may persist in the environment. Contains components with the potential to bioaccumulate. Poorly soluble mixture. May cause physical fouling of aquatic organisms. Product is expected to be practically non-toxic to aquatic organisms, LL/EL50 >100 mg/l. (LL/EL50 expressed as the nominal amount of product required to prepare aqueous test extract). Mineral oil is not expected to cause any chronic effects to aquatic organisms at concentrations less than 1 mg/l. Not expected to have ozone depletion potential, photochemical ozone creation potential or global warming potential. Product is a mixture of non-volatile components, which are not expected to be released to air in any significant quantities. SECTION 13 - DISPOSAL CONSIDERATIONS Recommended Method of Disposal: Container Disposal: Recycle if possible. Dispose of according to Federal, State and local governmental regulations. SECTION 14 - TRANSPORT INFORMATION Not classified as a Dangerous Good, according to the Australian Code for the Transport of Dangerous Goods by Road and Rail (6th Edition). Domestic (Land): UN No.: International Air Transportation (ICAO/IATA): UN No.: Maritime Transport IMDG: IMDG Class: IMDG Subrisk: UN Number: Packing Group: EMS Number: Special Provisions: Limited Quantities: Marine Pollutant: Shipping Name: No information found No information found No information found No SECTION 15 - REGULATORY INFORMATION Poisons Schedule (SUSDP): ADG Code: NOHSC: Not Listed. No information found Not Listed.

5 Material Safety Data Sheet: WNDG Heavy Duty Nozzle Dipping Gel Page 5 DISCLAIMER The information contained within this MSDS applies only to the ChemTools product to which the sheet relates. The information provided is based on our best knowledge at the time of issue. The information contained within this MSDS is believed to be accurate and is given in good faith. However, no warranty is made, either expressed or implied, regarding its accuracy or any liability arising out of the use of the information herein or the product supplied. When used in other preparations, formulations, or in mixtures, it is necessary to ascertain whether the classifications of the hazards have changed. The attention of the user is drawn to the possibility of creating other hazards when the product is used for purposes other than that for which it was recommended. In such cases, a reassessment may be necessary and should be made by the user. This safety data sheet should only be used and reproduced in order that the necessary measures are taken relating to the protection of health and safety at work. It is the responsibility of the handlers to pass on the totality of the information contained within this document to any subsequent person(s) who will come in to contact with, handle or use this product in any way. They should check the adequacy of the information provided within this MSDS before passing it on to their customers/staff.

6 SAFETY DATA SHEET ISSUED SEPTEMBER 2014 (VALID 5 YEARS FROM DATE OF ISSUE) CT-VSBP VIO-Flux Silver Brazing Flux MSDS SECTION 1 - IDENTIFICATION OF THE MATERIAL & COMPANY INFORMATION Chemtools Pty Ltd Phone: (business hours) Unit 2/14-16 Lee Holm Road Fax: St Marys NSW PRODUCT NAME Chemtools Weld Torch Coolant PRODUCT TYPE Coolant for self contained chillers PART NUMBER CT-WTC-5L, -20L AVAILABLE SIZES SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS HAZARDOUS COMPONENTS CAS # % ACGIH TLV OSHA PEL Ethyl alcohol <30 Non hazardous ingredients n/a balance SECTION 3 - HAZARDS IDENTIFICATION Relevant Routes of Exposure: Potential Health Effects: Inhalation: Skin Contact: Eye Contact: Ingestion: Skin, Inhalation, Eyes May cause respiratory tract irritation. High concentrations of vapours may cause headache, fatigue, drowsiness and dizziness. May cause allergic skin reaction. May cause skin irritation. Product has a defatting effect on skin. Prolonged contact may cause dryness of skin. Contact with eyes will cause irritation. HMIS: Health: Reactivity: Flammability: PPE: Warning: Flammable. Irritating to eyes and skin. Vapours may cause drowsiness and dizziness.

7 Material Safety Data Sheet: 8222 Low Strength Threadlocker Page 2 SECTION 4 - FIRST AID MEASURES General Information: Inhalation: Skin contact: Eye contact: Ingestion: Remove victim from exposure avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. Seek medical advice. Wash with soap and water. Remove contaminated clothing and shoes. Wash clothing before reuse. Get medical attention if symptoms occur. Check for and remove any contact lenses. Immediately flush with copious amounts of water, preferably, Lukewarm water for at least 15 minutes, holding eyelids open all the time. Get medical attention. Rinse mouth with water. Give water to drink. Do NOT induce vomiting. If vomiting occurs, place victims face downwards, head lower than hips to prevent vomit entering lungs. Seek immediate medical assistance. SECTION 5 - FIRE FIGHTING MEASURES Flash point: 34ºC (CC) Autoignition Temperature: 392ºC (ASTM D-2155) Flammable/Explosive Limits - Lower %: 3.50% Flammable/Explosive Limits - Upper %: 19.00% Extinguishing Media: Alcohol resistant foam, dry chemical or carbon dioxide. Special Fire Fighting Procedures: None Unusual Fire or Explosion Hazards: None Hazardous Combustion Products: Oxides of carbon. Keep run-off water out of sewers and water sources. SECTION 6 - ACCIDENTAL RELEASE MEASURES Environmental Precautions: Clean-up Methods: Shut off all possible sources of ignition. Increase ventilation. Clear area of all unprotected personnel. Wear protective equipment to prevent skin and eye contamination and inhalation of vapours. Contain using sand or soil prevent run off into drains and waterways. Use absorbent (soil, sand, vermiculite or other inert material). Collect and seal in properly labelled drums for disposal. SECTION 7 - HANDLING AND STORAGE Handling: Avoid contact with eyes, skin and clothing. Avoid breathing vapour and mist. Wash thoroughly after handling. Storage: Store in a cool place and out of direct sunlight. Store in well ventilated area. Store away from oxidising agents and acids. Store away from sources of heat or ignition. Keep containers closed at all times check regularly for leaks. Closed containers, exposed to temperatures >50º may develop excessive vapour pressure. Always open containers slowly to allow any excess pressure to vent. Store in accordance with Dangerous Goods (Storage and Handling) Regulations and AS1940 Storage and Handling of Flammable & Combustible Liquids. Incompatible products: Refer to Section 10.

8 Material Safety Data Sheet: 8222 Low Strength Threadlocker Page 3 SECTION 8 - EXPOSURE CONTROLS/PERSONAL PROTECTION Engineering controls: Respiratory protection: Skin protection: Eye/face protection: Exposure Limits: No specific ventilation requirements noted, but forced ventilation may still be required if concentrations exceed occupational exposure limits. Use approved respirator meeting the requirements of AS 1715 and AS 1716 if there is potential to exceed exposure limit(s). Available information suggests that gloves made from Butyl Rubber, or a combination laminate glove from PE/PA/PE or PE/EVAL/PE should be suitable. Butyl rubber gloves. Natural rubber gloves. Safety goggles or safety glasses with side shields. See Section 2 - Composition/Information on Ingredients SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES Physical State: Colour: Odour: Vapour Pressure: ph: Boiling Point/Range: Melting Point/Range: Specific Gravity: Vapour Density: Evaporation Rate: Solubility in Water: VOC Content: Liquid Clear, colourless Alcoholic Not available ºC -10ºC 0.95 at 20ºC at 20ºC (air=1) 2.53, nbuac=1) Completely miscible SECTION 10 - STABILITY AND REACTIVITY Stability: Hazardous polymerization: Hazardous decomposition products: Incompatibility: Conditions to avoid: Stable under normal conditions of use. Will not occur. Oxides of carbon. Strong oxidizers. Strong acids. See Section 7 - Handling and Storage Refer to 'Incompatibility', this section, above SECTION 11 - TOXICOLOGICAL INFORMATION Product toxicity data: Carcinogen Status: Hazardous components NTP Carcinogen IARC Carcinogen OSHA Carcinogen SECTION 12 - ECOLOGICAL INFORMATION Ecological Information: SECTION 13 - DISPOSAL CONSIDERATIONS Recommended Method of Disposal:

9 Material Safety Data Sheet: 8222 Low Strength Threadlocker Page 4 Container Disposal: SECTION 14 - TRANSPORT INFORMATION U.S. Department of Transportation Ground (49 CFR): Identification number: International Air Transportation (ICAO/IATA): Identification number: Water Transportation (IMO/IMDG): Identification number: Marine pollutant: SECTION 15 - REGULATORY INFORMATION United States Regulatory Information: DISCLAIMER The information contained within this MSDS applies only to the Chemtools product to which the sheet relates. The information provided is based on our best knowledge at the time of issue. The information contained within this MSDS is believed to be accurate and is given in good faith. However, no warranty is made, either expressed or implied, regarding its accuracy or any liability arising out of the use of the information herein or the product supplied. When used in other preparations, formulations, or in mixtures, it is necessary to ascertain whether the classifications of the hazards have changed. The attention of the user is drawn to the possibility of creating other hazards when the product is used for purposes other than that for which it was recommended. In such cases, a reassessment may be necessary and should be made by the user. This safety data sheet should only be used and reproduced in order that the necessary measures are taken relating to the protection of health and safety at work. It is the responsibility of the handlers to pass on the totality of the information contained within this document to any subsequent person(s) who will come in to contact with, handle or use this product in any way. They should check the adequacy of the information provided within this MSDS before passing it on to their customers/staff.