Annex B1 - Product environmental attributes Imaging equipment

Transcription

1 Annex B1 - Product environmental attributes Imaging equipment Ecma/TC38-TG3/2015/025 (Rev April 2015) The declaration may be published only when all rows and/or fields marked with * are filled-in (n.a. for not applicable). Additional information regarding each item may be found under P15. Brand * Konica Minolta Logo Company name * Konica Minolta Europe GmbH Contact information * address Internet site * Additional information The company declares (based on product specification or test results based obtained from sample testing), that the product conforms to the statements given in this declaration. Type of product * Multifunction Printer Commercial name * bizhub Model number * 758 Intended market * Global Europe Asia, Pacific & Japan Americas Other Additional information version 1.0 This is an uncontrolled copy when in printed form. Please refer to the contact information for the latest version. About Annex B1 Annex B1 reflects Product environmental attributes relevant for Imaging products. The following items from the ECMA-370 Main body are not shown in the template: P9.1 PTEC, ETEC and display resolution P12.1-P12.2 Ergonomic requirements. Annex B1 of ECMA th edition Page 1 (6)

2 Product environmental attributes - Legal requirements Requirement met Item Yes No n.a. P1 Hazardous substances and preparations P1.1* Products do comply with the current European RoHS Directive. (See legal reference and NOTE B1) P1.2* Products do not contain Asbestos Comment: Legal reference has no maximum concentration value. P1.3* P1.4* P1.5* P1.6* P1.7* P2 P2.1* P2.2* Products do not contain Ozone Depleting Substances: Chlorofluorocarbons (CFC), hydrobromofluorocarbons (HBFC), hydrochlorofluorcarbons (HCFC), Halons, carbontetrachloride, 1,1,1- trichloroethane, methyl bromide Comment: Legal reference has no maximum concentration values. Products do not contain more than; 0,005% polychlorinated biphenyl (PCB), 0,005% polychlorinated terphenyl (PCT) in preparations Products do not contain more than 0,1% short chain chloroparaffins (SCCP) with carbon atoms in the chain containing at least 48% per mass of chlorine in the SCCP Parts with direct and prolonged skin contact do not release nickel in concentrations above 0,5 g/cm 2 /week Comment: Max limit in legal reference when tested according to EN1811: REACH Article 33 information about substances in articles is available at (add URL or mail contact): env@konicaminolta.eu Batteries If the product contains a battery or an accumulator, the battery/accumulator is labeled with the disposal symbol. Information on proper disposal is provided in user manual. (See legal reference) Batteries or accumulators do not contain more than 0,0005% of mercury or 0,002% of cadmium. (See legal reference) P2.3* Batteries and accumulators are readily removable. (See legal reference) P3 P3.1* P3.2* P4 P4.1* Conformity verification & Eco design (ErP) The product is CE-marked to show conformance with applicable legal requirements The Declaration of Conformity can be requested at (add link or address): env@konicaminolta.eu The product complies with the Eco design requirements for energy-related products, Required information is; given in item P15 or added to this document, available at (add URL): Consumable materials If a photo conductor (drum, belt etc.) is used in the product, it does not contain cadmium max 0,01% (see legal reference and NOTE B1). P4.2* If ink/toner is used in the product, it does not contain cadmium max 0,1% by weight P4.3* P5 P5.1* P5.2* P5.3* P6 If the ink/toner formulation/preparation is classified as hazardous or contains a substance for which there are Community workplace exposure limits, the product/packaging is adequately labeled according to applicable regulations and a Safety Data Sheet (SDS) in accordance with these requirements is available Product packaging Packaging and packaging components do not contain more than 0,01% lead, mercury, cadmium and hexavalent chromium by weight of these together. The packaging materials are marked with abbreviations and numbers indicating the nature of the material(s) used The product packaging material is free from ozone depleting substances as specified in the Montreal Protocol Comment: Legal reference has no maximum concentration values. Treatment information P6.1* Information for recyclers/treatment facilities is available NOTE B1 Restriction applies to the homogeneous material, unless other specified and expressed in weight %. Stating Yes means that the product is compliant with the mandatory requirements. Annex B1 of ECMA th edition Page 2 (6)

3 Product environmental attributes - Market requirements (See General NOTE GN below) - Environmental conscious design Requirement met Item *=mandatory to fill in. Additional information regarding each item may be found under P14. Yes No n.a. P7 Design Disassembly, recycling P7.1* Parts that have to be treated separately are easily separable P7.2* Plastic materials in covers/housing have no surface coating. P7.3* Plastic parts > 100 g consist of one material or of easily separable materials. P7.4* Plastic parts > 25 g have material codes according to ISO referring ISO P7.5 Plastic parts are free from metal inlays or have inlays that can be removed with commonly available tools. P7.6* Labels are easily separable. (This requirement does not apply to safety/regulatory labels). Product lifetime P7.7* Upgrading can be done e.g. with processor, memory, cards or drives P7.8* Upgrading can be done using commonly available tools P7.9. Spare parts are available after end of production for: 7 years P7.10 Service is available after end of production for: 7 years P7.11* Material and substance requirements Product cover/housing material type (e.g. plastics, metal, aluminum): Material type: PC-PET Material type: PC-ABS Material type: PS P7.12 Insulation materials of external electrical cables are PVC free. P7.13 Insulation materials of internal electrical cables are PVC free. P7.14 External plastic casing/cover parts > 25 g contain no more than 0,1% weight (1000 ppm) bromine and 0,1% weight (1000 ppm) chlorine attributable to brominated flame retardants, chlorinated flame retardants, and polyvinyl chloride or 0,3% weight (3000 ppm) bromine and 0,3% weight (3000 ppm) chlorine in parts containing more than 25% post-consumer recycled content. P7.15 Printed circuit boards, PCBs (without components) are low halogen: all PCBs > 25 g are low halogen as defined in IEC (See NOTE B2) P7.16 Flame retarded plastic parts > 25 g in covers / housings are marked according ISO : Marking: FR(40) P7.17 Alt. 1: Chemical specifications of flame retardants in printed circuit boards > 25 g (without components): TBBPA (additive), TBBPA (reactive) (See NOTE B3), Other; chemical name:, CAS #: Alt. 2: Chemical specifications of flame retardants in printed circuit boards (without components) > 25 g according ISO : FR(17) P7.18 Alt. 1: Flame retarded plastic parts > 25 g contain the following flame retardant substances/preparations in concentrations above 0,1%: 1. Chemical name:, CAS #: (See NOTE B4) 2. Chemical name:, CAS #: 3. Chemical name:, CAS #: Alt. 2: Chemical specifications of flame retardants in plastic parts > 25 g according ISO : FR(17), FR(40) P7.19 In plastic parts > 25 g, flame retardant substances/preparations above 0,1% are used which have been assigned the following Risk phrases; and Hazard statements: The source(s) for these classifications is/are found at (add URL(s)):, (See NOTE B5) P7.20* Postconsumer recycled plastic material content is used in the product (See NOTE B6): If YES; at least one of the two alternatives below shall be answered; a) Of total plastic parts weight > 25 g, the postconsumer recycled plastic material content (calculated as a percentage of total plastic by weight) is 21.9 %. or b) The weight of recycled material is g. GENERAL NOTE Standard references should direct to the latest version of a standard. If an older version of a standard is used, section P15 shall be used for explanation. NOTE B2 IEC defines maximum limits of 900 ppm for each of the substances chlorine and bromine and a maximum limit of 1500ppm of these substances combined. The standard does not address fluorine, iodine and astatine which are included in the group of halogens. NOTE B3 and B4 A Guidance document on Chemical substances is available; NOTE B5 If a certain substance has been assigned a certain risk phrases / hazard statement in the referenced source, this does not necessarily mean the substance has been tested for all of the hazards referred to by a certain customer. NOTE B6 Applies to a product containing plastic parts whose combined weight exceeds 100 g with the exception of printed circuit boards, cables, connectors and electronic components and bio-based plastic material. Annex B1 of ECMA th edition Page 3 (6)

4 Product environmental attributes - Market requirements (continued) Requirement met Item Yes No n.a. Material and substance requirements (continued) P7.21* Biobased plastic material content is used in the product (See NOTE B7): P7.22* If YES; at least one of the two alternatives below shall be answered; a) Of total plastic parts weight > 25 g, the biobased plastic material content (calculated as a percentage of total plastic by weight) is %. or b) The weight of the biobased plastic material is g. Light sources are free from mercury, i.e. less than 0,1 mg/lamp. If mercury is used specify: Number of lamps: and maximum mercury content per lamp: mg P8 Batteries P8.1* Battery chemical composition: Lithium P9 Energy consumption (See NOTE B8) P9.1 For the product the following power levels or energy consumptions are reported: Energy mode * Sleep mode for ENERGY STAR Operational Mode (OM) products Standby/off mode for ENERGY STAR Operational Mode (OM) products TEC value for ENERGY STAR TEC products (TEC= Typical Energy Power level at 100 V AC Power level at 115 V AC W W W W W W Power level at 230 V AC 4.9 kwh/week kwh/week 5.1 kwh/week Energy Star Reference/Standard for energy modes and test method * Maximum 1500 W W 2100 W RAL UZ-171 Active (Printing) 1090 W W 1270 W RAL UZ-171 Ready 232 W W 235 W RAL UZ-171 Low power W W 86.6 W RAL UZ-171 Sleep 0.37 W W 0.42 W RAL UZ-171 Plug-in off W W W RAL UZ-171 External Power Supply Efficiency Level (International Efficiency Marking Protocol) * : Print/Scan Speed * : 95 images per minute Default time to enter energy save mode: minutes P9.2* Information about the energy save function is provided with the product. P10 Emissions Noise emission Declared according to ISO 9296 (See NOTE B9) P10.1 Mode Mode description Statistical upper limit A-weighted sound power level, LWA,c (B) Idle * Ready * 5.3 Operation * Printing * 7.4 Other mode Measured according to: ISO 7779 ECMA-74 Other (only if not covered by ECMA-74) NOTE B7 The following is to be excluded from the calculation of percentage: printed circuit boards, labels, cables, connectors and electronic components and postconsumer recycled plastic. NOTE B8 A Guidance document on Energy Efficiency is available; NOTE B9 A Guidance document on Acoustic Noise is available; Annex B1 of ECMA th edition Page 4 (6)

5 Product environmental attributes - Market requirements (continued) Requirement met Item Yes No n.a. Chemical emissions from printing products (See NOTE B10) P10.2* Test performed according to ECMA-328 Determination of Chemical Emission Rates from Electronic Equipment (ISO/IEC 28360), other specify: RAL UZ-171 P10.3 Typical emission rate (operation phase) is (mg/h): P11 Electrophotographic devices: Ozone 0.15 Dust 2.0 Styrene 0.36 Benzene 0.01 TVOC 3.94 Ink devices: Dust Styrene Benzene TVOC Note: compliance with maximum emission rates in eco labels to be declared in P14. Consumable materials for printing products P11.1* A Safety Data Sheet (SDS) is available for the ink/toner preparation, even if not legally required (see P4.3). P11.2* Paper containing post-consumer recycled fibers can be used, provided that it meets the requirements of EN P11.3* 2-sided (duplex) printing/copying is an integrated product function. P11.4* The product is delivered to end-user with default auto-duplex enabled. P13 Packaging and documentation P13.1* Product packaging material type(s): wood weight (kg): 13.3 Product packaging material type(s): paper weight (kg): 13.2 Product packaging material type(s): foamed PS weight (kg): 1.8 P13.2* Product plastic primary packaging is free from PVC. P13.3* For product primary corrugated fiberboard packaging, specify the contained percentage of minimum postconsumer recovered fiber content: 70 % P13.4* Specify media for user and product documentation (tick box): Electronic, Paper, Other P13.5 (Please only complete this item if paper documentation used) User and product documentation on paper media is chlorine-free: If Yes, please specify: P14 Totally chlorine-free Elemental chlorine-free Processed chlorine-free Voluntary programs: P14.1 The product meets the requirements of the following voluntary program(s): ENERGY STAR Criteria version: 2 Date: Product category: MFDs Eco-label: Blue Angel Criteria version: RAL-UZ 171 Date: July 2012 Product category: Multi Function Device Eco-label: Criteria version: Date: Product category: P15 Additional information (See NOTE B11) BTU 134 BTU/h The figure is based on the TEC value of 6.6 kwh / week (=24 h x 7 days) (230v) Sound Lpam=35.7dB(ready), 56.2 db(active) Pressure P3.2 This product complies with Lot6 and Lot26 of Eco design Requirement. NOTE B10 A Guidance document on Chemical Emissions is available; NOTE B11 Additional lines may be inserted to declare further items, by positioning the cursor at the far right of the row and hitting the <Enter> key. Annex B1 of ECMA th edition Page 5 (6)

6 Legal references Europe Annex B1 Reference Directive 2011/65/EU (RoHS Directive) * * Specific exemptions apply for certain products and applications. Declaration item P1.1, P4.1 (EC) 1907/2006(REACH, Annex XVII P1.2, P1.4, P1.6, P1.7, P4.2 Regulation (EC) No. 2037/2000, 2038/2000, 2039/2000, (Marketing and use of Ozone layer depleting substances) Norwegian regulation relating to restrictions on the use of certain dangerous chemicals P1.3, 5.3 P1.5 REACH" Regulation (1907/2006), annex VII P1.10 Directive 2013/56/EC (Battery and accumulators Directive) * * These provisions shall not apply where, for safety, performance, medical or data integrity reasons, continuity of power supply is necessary and requires a permanent connection between the appliance and the battery or accumulator. Directive 2006/95/EC (Low Voltage Directive) P3.1 Directive 2004/108/EC (EMC Directive) P3.1 Directive 1999/5/EC (R&TTE Directive) P3.1 Regulation (EC) 801/2013 amending Regulation (EC) No 1275/2008 with regard to ecodesign requirements for standby, off mode electric power consumption of electrical and electronic household and office equipment, and amending Regulation (EC) No 642/2009 with regard to ecodesign requirements for televisions Regulation (EC) 1907/2006 (REACH Regulation), Article 31, annex II) P2.1, P2.2, P2,3, P8.1 P3.1, P3.2 P4.3 Regulation (EC) 1272/2008 (CLP Regulation) P4.3, P7.19 Directive 2004/12/EC ( Packaging Directive) P5.1 Decision 97/129/EC ( Secondary packaging legislation) P5.2 Directive 2012/19/EU (WEEE directive) P6.1 Annex B1 of ECMA th edition Page 6 (6)