Heat Pump KEYMARK. Date Description of modification Revision number Initial version 1

Transcription

1 Page: 1 f 26 Date Descriptin f mdificatin Revisin number Initial versin 1 10/03/2017 Additin f air/air Editrial changes Annex E included in reference t pren suppressed Reference t EN is added rerating prcess chart was added ne testing pint is added fr peridic cntrl test peridic cntrl test selectin has been mdified 12/09/2017 SCOP tl usage details Editrial changes Safety test fr dmestic ht water heat pumps Peridic surveillance prcess and rerating rules have been mdified 3 CONTENTS 1 Classificatin f prducts Type Sub-type Mdel First admissin Factry inspectin First admissin testing Sampling rules Data declaratin Mdificatin and adding f sub-type Test descriptin SCOP and SEER calculatins Peridic surveillance Factry inspectin Surveillance test prcess Mdel and unit selectin rules Peridicity Receptin f unit by recgnised labratry Perfrmances t be tested Heat pumps fr space heating and cmbinatin heat pumps except air/air type Heat pumps designed fr dmestic ht water prductin Air/air heat pumps fr space heating nly Air/air heat pumps fr space cling nly Air/air heat pumps fr space heating and cling Rerating rules General rules Space heating/cling perfrmances rerating rules... 16

2 Page: 2 f Perfrmances accrding t EN r t EN Perfrmances accrding t EN Dmestic ht water perfrmances rerating rules η DHW V 40 nly fr dmestic ht water heat pumps Other EN perfrmances Sund pwer level rerating rules... 22

3 Page: 3 f 26 1 Classificatin f prducts 1.1 Type A type f heat pumps is defined by the use f the same: Heat surce Heat sink Driving energy (gas, electricity etc.). The types cvered by the KEYMARK Scheme are: Outdr air (r exhaust air)/water - heat pumps Water/water (including brine/water) - heat pumps Direct expansin/water - heat pumps Air/air utdr air/recycled air heat pumps and air cnditiners except single duct and duble duct units The types are declared by the manufacturers. 1.2 Sub-type A sub-type is part f a type. Heat pumps with an identical refrigeratin circuit design, including same refrigerant and mass f refrigerant are cnsidered as being the same subtype if they fulfil all cnditins belw: Same cmpressr: identical (same manufacturer and cmmercial reference) Same cndenser: identical (same manufacturer and cmmercial reference) Same evapratr: identical (same manufacturer and cmmercial reference) except fr air/air multi-split units Same defrst prcess (when relevant) Expansin device: same technlgy In additin, fr cmbinatin heat pumps and heat pumps nly designed fr dmestic ht water (DHW) prductin: Same tank vlume Same heat exchanger Fr air/air multi-split units the sub-type classificatin nly applies t utdr unit. Sub-types are declared by manufacturers but the final decisin n sub-types rests with the certificatin bdy. 1.3 Mdel A sub-type may cnsist f several different mdels, i.e. heat pumps using identical refrigeratin circuits, but therwise differ in design. Examples f such differences are given, but nt limited t the list belw

4 Page: 4 f 26 With r withut integrated circulatr pump(s) With r withut integrated strage tank With r withut integrated back up heater Different sizes and crrsin prtectin f strage tank(s) Different lcatin and dimensins n pipe cnnectins Different electrical supply (frequency, single/three phases) Different brand names Mdels are declared by manufacturers but the final decisin n mdels rests with the certificatin bdy. 2 First admissin 2.1 Factry inspectin Factry inspectin is part f the first admissin prcess and shall be perfrmed accrding Annex B. 2.2 First admissin testing Admissin tests shall be cnducted in a recgnised labratry (see Annex H). Samples fr type testing shall be selected by the certificatin bdy. Fr the sampling prcess the applicant shall prvide a minimum f three units (traceable by serial numbers) fr the sub-type selected by the certificatin bdy; frm which certificatin bdy will select ne randm unit (traceable by serial number) t be tested by recgnised labratry. The certificatin bdy als indicates t the manufacturer the testing cnditins (climates; temperature applicatin and part lad cnditins). The manufacturer shall send the sample t a recgnised labratry and infrm the certificatin bdy within the fllwing mnth abut the schedule and place fr the tests.

5 Page: 5 f Sampling rules Sample size fr all types f heat pumps except air/air type Table 1 Minimum number f sub-types t be tested in a type Number f sub-types t be certified Number f sub-type t be tested 5 1 > > > > > 25 every 5 th sub-type will require ne additinal test Sample size fr air/air types Fr air/air type, different rules fr single split/package units and multi-split units apply Single split and package units Table 2 Minimum number f sub-types t be tested in a type Number f sub-types t be certified Number f sub-type t be tested 10 1 > > > > > 50 every 10 th sub-type will require ne additinal test Multi-split units Table 3 Minimum number f utdr sub-types t be tested in a type Number f sub-types t be certified Number f utdr units t be tested 5 1 > > >

6 Page: 6 f 26 Number f sub-types t be certified Number f utdr units t be tested > > 25 As each utdr unit can be cmbined with several kinds f indr units Wall Ducted Cassette Flr Ceiling Etc. every 5 th sub-type will require ne additinal test The cmbinatin f the utdr unit with indr units shall be selected s that the capacity rati is equal t 1 (±5%) within the cmbinatins declared by the manufacturer. All declared kinds f indr units shall be tested in cmbinatin with ne r several f the selected utdr units at least nce Data declaratin The applicant shall declare all the requested data in the Heat Pump KEYMARK database fr all sub-types Mdificatin and adding f sub-type Mdificatin f certified types (see Annex F) Additinal tests are nly needed if the mdificatin has an impact n the certified perfrmance (either n heating/cling perfrmance, DHW prductin r sund pwer level); the manufacturer has t infrm the certificatin bdy abut changes f cmpnents The rules fr the number f tests t be perfrmed are the same as fr admissin Additin f ne r several sub-types in a type (see Annex F) The rules fr the number f sub-types t be tested are the same as fr admissin The test must be perfrmed in a recgnised labratry Extensin f certified sub-types t anther brand (see Annex G) N additinal prduct test is required Technical dcumentatin check accrding t EN / EN / EN

7 Page: 7 f 26 The manufacturer has t sign and prvide a written cnfirmatin that n technical change that can affect the perfrmance, has been made t the sub-types. The final decisin n mdificatin rests with the certificatin bdy Test descriptin Test Pints fr all types except air/air type Heat pump fr space heating nly Space heating tests fr lw temperature heat pump If bth water and brine as heat surce are certified, tests shall be carried ut with bth heat surces. a) A7/W35; A20/W35; B0/W35; W10/W35 accrding t EN and E4/W35 accrding t EN b) Bivalent temperature cnditin accrding t EN fr average climate c) One ther testing cnditin t be chsen by the certificatin bdy accrding t EN fr average climate d) Fr any ther climate, bivalent temperature cnditin shall be tested accrding t EN Space heating tests fr medium temperature heat pump If bth water and brine as heat surce are certified, tests shall be carried ut with bth heat surces. Fr each lw and medium temperature applicatin, the fllwing tests shall be perfrmed: a) A7/W35/55; A20/W35/55; B0/W35/55; W10/W35/55; accrding t EN and E4/W35/55 accrding t EN b) Bivalent temperature cnditin accrding t EN fr average climate c) One ther testing cnditin t be chsen by the certificatin bdy accrding t EN fr average climate d) Fr any ther climate, bivalent temperature cnditin shall be tested accrding t EN Sund pwer level tests Tests shall be perfrmed accrding t EN fr average climate at the certified highest temperature applicatin. Fr heat pumps certified fr brine and water as heat surce, the sund pwer level test is perfrmed using brine Safety tests Safety tests shall be perfrmed: Accrding t EN clauses as fllw:

8 Page: 8 f 26 Air/Water chapter starting test accrding t table 1 chapter 4.4 shutting ff the heat transfer medium flw chapter 4.5 cmplete pwer supply failure chapter 4.7 defrst test, nly fr utdr air units Brine/Water chapter starting test accrding t table 1 chapter 4.4 shutting ff the heat transfer medium flw chapter 4.5 cmplete pwer supply failure Water/Water chapter starting test accrding t table 1 chapter 4.4 shutting ff the heat transfer medium flw chapter 4.5 cmplete pwer supply failure In case the heat pump can be used with brine r water, nly ne applicatin (brine r water) shall be tested. Accrding t EN clauses as fllw: Direct exchange chapter 7.1 starting test accrding t Table 8 chapter pressure drp chapter shutting f the heat transfer medium flw chapter cmplete pwer supply failure Air flw fr exhaust air heat pumps The manufacturer shall declare the exhaust air vlume flw that shall be used fr space heating test Cmbinatin heat pump Heating mde tests If bth water and brine as heat surce are certified, tests shall be carried ut with bth heat surces. a) A7/W55; A20/W55; B0/W55; W10/W55 accrding t EN and E4/W55 accrding t EN b) Bivalent temperature cnditin accrding t EN fr average climate c) One ther testing cnditin t be chsen by the certificatin bdy accrding t EN fr average climate d) Fr any ther climate, bivalent temperature cnditin shall be tested accrding t EN Lw temperature applicatin can be certified as an ptin; in this case, testing at lw temperature applicatin shall be perfrmed accrding Sund pwer level tests

9 Page: 9 f 26 Tests shall be carried ut accrding t EN fr medium temperature applicatin fr average climate. Fr heat pumps certified fr brine and water as heat surce, the acustic test is carried ut using brine Dmestic ht water tests Tests shall be perfrmed accrding t EN fr average climate. Tests may als perfrmed accrding t EN fr any ther declared climate. The tests shall be perfrmed fr the lad prfiles as declared by the manufacturer in the data sheet fr each climate where relevant. Fr water (brine)/water type, in case brine and water as heat surce are declared, nly ne heat surce shall be tested. The heat surce t be tested is chsen by the certificatin bdy Safety tests Safety tests shall be perfrmed: Accrding t EN clauses as fllw: Air/Water chapter starting test accrding t table 1 chapter 4.4 shutting ff the heat transfer medium flw chapter 4.5 cmplete pwer supply failure chapter 4.7 defrst test, nly fr utdr air unit Brine/Water chapter starting test accrding t table 1 chapter 4.4 shutting ff the heat transfer medium flw chapter 4.5 cmplete pwer supply failure Water/Water chapter starting test accrding t table 1 chapter 4.4 shutting ff the heat transfer medium flw chapter 4.5 cmplete pwer supply failure In case the heat pump is declared fr brine and water as heat surce, nly ne heat surce (brine r water) shall be tested. Accrding t EN clauses as fllw: Dirext exchange chapter 7.1 starting test accrding t Table 8 chapter pressure drp chapter shutting f the heat transfer medium flw chapter cmplete pwer supply failure Air flw fr exhaust air heat pumps The manufacturer shall declare the exhaust air vlume flw that shall be used fr bth space heating test and DHW test.

10 Page: 10 f Heat pump fr dmestic ht water nly Perfrmance tests Tests shall be perfrmed accrding t EN fr average climate. Tests may als be perfrmed accrding t EN fr any ther declared climate. The tests shall be perfrmed fr the lad prfiles as declared by the manufacturer in the data sheet fr each climate where relevant. Fr water (brine)/water type, in case brine and water as heat surce are declared, nly ne heat surce shall be tested. The heat surce t be tested is chsen by the certificatin bdy Sund pwer level tests Tests shall be perfrmed fr average climate accrding t the Eurpean standard when available Safety tests Safety test shall be perfrmed accrding t EN 16147: 8.1.: temperature perating range 8.3.: safety devices checking test 8.4.: cndensate draining Air flw fr exhaust air heat pumps The manufacturer shall declare the exhaust air vlume flw that shall be used Test pint fr air/air types Heat pump fr space heating nly Space heating tests a) Bivalent temperature cnditin accrding t EN fr average climate b) One ther testing cnditin t be chsen by the certificatin bdy accrding t EN fr average climate c) Fr any ther climate, bivalent temperature cnditin shall be tested accrding t EN Sund pwer level tests Tests shall be perfrmed accrding t EN fr average climate Safety tests

11 Page: 11 f 26 Safety tests shall be perfrmed accrding t EN clauses as fllw: chapter starting test accrding t table 1 chapter 4.4 shutting ff the heat transfer medium flw chapter 4.5 cmplete pwer supply failure chapter 4.7 defrst test Heat pump fr space cling nly Space cling tests a) Test cnditin A accrding t EN b) One ther testing cnditin t be chsen by the certificatin bdy accrding t EN Sund pwer level tests Tests shall be carried ut accrding t EN Safety tests Safety tests shall be perfrmed accrding t EN clauses as fllw: chapter starting test accrding t table 1 chapter 4.4 shutting ff the heat transfer medium flw chapter 4.5 cmplete pwer supply failure chapter 4.7 defrst test Heat pump fr space heating and cling Space cling tests a) Test cnditin A accrding t EN b) One ther testing cnditin t be chsen by the certificatin bdy accrding t EN Space heating tests a) Bivalent temperature cnditin accrding t EN fr average climate b) One ther testing cnditin t be chsen by the certificatin bdy accrding t EN fr average climate c) Fr any ther climate, bivalent temperature cnditin shall be tested accrding t EN 14825

12 Page: 12 f Sund pwer level tests Tests shall be perfrmed accrding t EN in cling mde Safety tests Safety tests shall be perfrmed accrding t EN clauses as fllw: chapter starting test accrding t table 1 chapter 4.4 shutting ff the heat transfer medium flw chapter 4.5 cmplete pwer supply failure chapter 4.7 defrst test SCOP and SEER calculatins Fr SCOP and SEER calculatins, certificatin bdies shall use the SCOP tls apprved by the HPSG. 3 Peridic surveillance The peridic surveillance prcess shall start 12 mnths after the first certificate has been granted t the applicant. Surveillance (including psitive assessment f certificatin bdy) has t be cmpleted nt later than 3 mnths after the prcess has started. The prcess starts with the factry inspectin where mdels are chsen by recgnised inspectr fr surveillance test. Surveillance test prcess and rules apply t each type independently. Rerating rules shall be applied t each failed test accrding clause 4. The surveillance prcess is passed if bth factry inspectin and test are cnfirmed t be cnfrm by the certificatin bdy. 3.1 Factry inspectin Factry inspectin shall be perfrmed at each manufacturing site at least every 12 mnths accrding Annex B. 3.2 Surveillance test prcess Peridicity f surveillance test depends n the test results and number f manufacturing sites. A surveillance test is passed when the certificatin bdy has cnfirmed that all the certified perfrmances that are tested are cnfrmed t the declared perfrmances accrding the scheme requirements. A surveillance test is failed when at least ne f the certified perfrmance that is tested deviates frm the declared perfrmance in a higher level than the defined tlerances. The certified perfrmances are listed in scheme rules dcuments clause 8.

13 Page: 13 f Mdel and unit selectin rules The mdels t be tested shall be selected by certificatin bdy and units shall be chsen by recgnised inspectr. Fr a surveillance test, ne mdel f a sub-type per type is selected by the certificatin bdy. If heat pumps fr space heating and cmbinatin heat pumps are certified a cmbinatin heat pump shall be selected. One unit f the selected mdel shall be chsen by a recgnised inspectr frm the existing stck f prducts r directly frm the prductin line. The unit selectin may be dne during an annual factry inspectin r during a specific visit upn certificatin bdy request. In case f split type heat pump, this rule applies t the indr and utdr parts f the selected mdel Peridicity Single manufacturing site Regular surveillance test peridicity is 24 mnths. If the surveillance test is passed, then the next surveillance will be perfrmed after 24 mnths. In case the surveillance test is failed, the next surveillance, n anther mdel f anther sub-type r same sub-type upn decisin f certificatin bdy, shall be perfrmed after 12 mnths. The unit t be tested shall be chsen during factry inspectin. In case this test perfrmed 12 mnths later than the first ne is als failed, anther test, n anther mdel f anther sub-type r same sub-type upn decisin f certificatin bdy shall be perfrmed after 6 mnths. The unit t be tested shall be chsen by a recgnised inspectr. The peridicity remains ne test every 6 mnths until the test is passed. Then the regular peridicity applies again. Multi manufacturing sites If the manufacturing f a type takes place at mre than ne manufacturing site, the regular surveillance test peridicity is 12 mnths. The unit t be tested shall be selected frm a different manufacturing site every 12 mnths. Fr air/air type, nly the manufacturing sites f the utdr units are cnsidered fr the fllwing prcedure. If the surveillance test is failed the regular surveillance test peridicity as described abve ges n but in additin, anther unit manufactured at the same manufacturing site shall be tested after 12 mnths. The mdel can belng t anther sub-type r t the same sub-type upn decisin f the certificatin bdy. The unit t be tested shall be chsen by a recgnised inspectr. In case this secnd test is failed, anther unit manufactured n the same manufacturing site shall be perfrmed after 6 mnths. The mdel can belng t anther sub-type r t the

14 Page: 14 f 26 same sub-type upn decisin f the certificatin bdy. The unit t be tested shall be chsen by a recgnised inspectr. The peridicity remains ne test every 6 mnths until the test is passed. Then the regular peridicity applies again. The prcess is described thrugh an example and a chart in a nte at the end f this dcument Receptin f unit by recgnised labratry After the unit has been chsen by the recgnised inspectr the certificate hlder shall send the unit t a recgnised labratry and shall infrm the certificatin bdy within the fllwing mnth abut the schedule and place fr the tests. 3.3 Perfrmances t be tested Heat pumps fr space heating and cmbinatin heat pumps except air/air type Fr heat pumps certified fr brine and water as heat surce, the certificatin bdy shall chse ne f these heat surces t be used during the fllwing tests. Sund pwer level is tested accrding t EN 12102; bth utdr and indr units shall be tested, where relevant, under average climate. In the case f lw temperature heat pumps, the sund pwer level is tested at lw temperature cnditin, in the case f medium temperature heat pumps r cmbinatin heat pumps, the sund pwer level is tested at medium temperature cnditin. Fr lw temperature heat pumps: a) A7/W35; A20/W35; B0/W35; W10/W35 accrding t EN and E4/W53 accrding t EN where relevant b) Bivalent temperature cnditins accrding t EN fr average climate c) One ther part lad cnditin t be chsen by the certificatin bdy accrding t EN fr average climate d) Fr any ther declared climate, bivalent testing temperature cnditin and anther part lad cnditin t be chsen by the certificatin bdy shall be tested accrding t EN Fr medium temperature heat pumps: Lw r medium temperature applicatin has t be chsen by the certificatin bdy, then the same test as described fr lw temperature heat pumps in clause is t be perfrmed. Fr cmbinatin heat pumps: a) Heating mde test: if nly medium temperature applicatin is declared the same test as described fr lw temperature heat pumps in clause is t be applied fr medium temperature applicatin

15 Page: 15 f 26 If bth lw and medium temperature applicatins are declared, lw r medium temperature applicatin has t be chsen by the certificatin bdy, then the same test as described fr lw temperature heat pumps in clause is t be perfrmed b) DHW efficiency, ƞ DHW, accrding t EN under average climate fr the lad prfile declared by the manufacturer c) DHW efficiency, ƞ DHW, accrding t EN under anther declared climate fr the lad prfile declared by the manufacturer Heat pumps designed fr dmestic ht water prductin Fr heat pumps certified fr brine and water as heat surce, the certificatin bdy shall chse ne f these heat surces t be used during the fllwing tests. Sund pwer level accrding t the Eurpean standard when it will be available. Where relevant, bth indr and utdr units shall be tested. Sund pwer level is nly tested under average climate cnditins DHW efficiency, ƞ DHW, accrding t EN fr average climate fr the lad prfile declared by the manufacturer DHW efficiency, ƞ DHW, accrding t EN under anther declared climate fr the lad prfile declared by the manufacturer V 40 accrding t EN fr average climate fr the lad prfile declared by the manufacturer V 40 accrding t EN fr anther climate fr the lad prfile declared by the manufacturer Air/air heat pumps fr space heating nly Sund pwer level is tested accrding t EN Bth utdr and indr units shall be tested where relevant. Fr package units, bth utdr and indr sund pwer level shall be measured. Heating mde test a) Bivalent temperature cnditins fr average climate accrding t EN b) One ther part lad cnditin t be chsen by the certificatin bdy accrding t EN fr average climate c) Fr any ther declared climate, bivalent temperature cnditin and anther part lad cnditin t be chsen by the certificatin bdy shall be tested accrding t EN Air/air heat pumps fr space cling nly Sund pwer level is tested accrding t EN Bth utdr and indr units shall be tested where relevant. Fr package units, bth utdr and indr sund pwer level shall be measured. Cling mde test a) Part lad cnditin A accrding t EN 14825

16 Page: 16 f 26 b) One ther part lad cnditin t be chsen by the certificatin bdy accrding t EN Air/air heat pumps fr space heating and cling Sund pwer level is tested accrding t EN in cling mde. Bth utdr and indr units shall be tested where relevant. Fr package units, bth utdr and indr sund pwer levels shall be measured. Heating mde test a) Bivalent temperature cnditins fr average climate accrding t EN b) One ther part lad cnditin t be chsen by the certificatin bdy accrding t EN fr average climate c) Fr any ther declared climate, bivalent temperature cnditin and anther part lad cnditin t be chsen by the certificatin bdy shall be tested accrding t EN Cling mde test a) Part lad cnditin A accrding t EN b) One ther part lad cnditin t be chsen by the certificatin bdy accrding t EN Rerating rules 4.1 General rules When a perfrmance test is failed the rerating rules apply t the crrespnding perfrmance f all the mdels in the sub-type in which the tested unit belngs t. Fr the perfrmances nn-listed in the Scheme Rules clause 8 that are tested (eg: EN perfrmances), in case measured data dn t match with declared data, the rerating rules apply t all the mdels in the sub-type in which the tested unit belngs t. Several perating mdes are tested during surveillance tests: acustic, heating, cling and DHW. Rerating rules apply independently t each mde and t the characteristics fr which the tlerances are set in clause 4.2. that has failed within this mde ð E.g.: failure n utdr unit sund pwer level test leads t rerating f sund pwer level f the utdr unit f the mdels f the cnsidered sub-type. 4.2 Space heating/cling perfrmances rerating rules Perfrmances accrding t EN r t EN Tlerance n heating capacity and COP measured at standard rating cnditins accrding t EN is equal t -8%. If bth the measured heating capacity and COP are nt lwer than 8% cmpared t declared values, then the EN tests shall be perfrmed accrding the flwrate declared by the applicant.

17 Page: 17 f 26 If an bserved deviatin between declared and measured heating capacity r COP exceeds - 8 %, then EN tests shall be perfrmed accrding t the measured flwrate and the EN declared perfrmances shall be rerated as fllw: Rerating f tested mdel rerated heating capacity = measured capacity ( ) Equatin 1 rerated COP = measured COP ( ) Equatin 2 Rerating f the ther mdels f the sub-type Same relative deviatin in between declared and rerated heating capacity f the tested mdel shall be applied t the heating capacity f the ther mdels f the sub-type. Same relative deviatin in between declared and rerated COP f the tested mdel shall be applied t the COP f the ther mdels f the sub-type. Input pwer rerating fr all mdels rerated input pwer = rerated heating capacity rerated COP Equatin Perfrmances accrding t EN Space heating The rerating rules apply independently t each declared climate. In case a test in heating mde is failed and in case f tw heat surces are declared, bth heat surces shall be rerated unless the certificate hlder asks fr a full test n bth heat surces fr all the declared temperature applicatins fr the failed climate. A full test means: test accrding t EN , test accrding t EN at every part lad cnditins and test f an auxiliary mde chsen by the certificatin bdy. Fr the space heating test t be cnsidered as passed the space heating tests fr all declared climates need t be passed. a) Test at bivalent temperature cnditin Bivalent temperature cnditin shall be tested first. If the measured heating capacity at T biv fulfil the fllwing criteria: T BCD = E FGHIJK ELMIJK P NOPQRSON TOUCVWX ± 10% Equatin 4 then the test cntinues. If nt, the test is interrupted. The certificate hlder shall prvide a new cmplete set f declared values t the certificatin bdy and t the recgnised labratry within tw weeks after the interrupted test. The tests may then be restarted frm the beginning and the P designh shall be rerated as fllw: Rerating f the tested mdel:

18 Page: 18 f 26 rerated P designh = P j T biv TOLI16 T biv I16 Equatin 5 Rerating f the ther mdels f the sub-type and f the ther heat surce when relevant: Same relative deviatin between declared and rerated P designh f the tested mdel shall be applied t the ther mdels f the sub-type and t the ther heat surces when relevant. When test at bivalent temperature cnditin has been cmpleted, the ther selected part lads shall be tested. b) Test at ther part lad cnditins At each part lad cnditin, measured COP shall nt be lwer than -8% cmpared t the declared COP. If each measured COP is within the tlerance, SCOP is calculated using the declared COP fr each part lad cnditins and declared auxiliary mdes cnsumptin. If the calculated SCOP is nt lwer than -8% cmpared t the declared SCOP, then the test is ver and nr SCOP nr η are rerated. If the calculated SCOP is lwer than -8% cmpared t the declared SCOP, the declared SCOP and η shall be rerated. The rerated SCOP and η shall be equalled t the calculated nes. SCOP and η fr each mdels f the sub-type fr each declared applicatins and each declared climates shall be calculated accrding the declared part lad data and auxiliary mdes cnsumptin. Each SCOP being lwer than the calculated value -8% shall be replaced by the calculated SCOP and η shall be recalculated accrdingly If at least ne f the measured COP is lwer than -8% cmpared t the declared COP then, all the nn-tested EN part lad cnditins and ne auxiliary mde cnditin (chsen by the certificatin bdy) shall be tested. SCOP is calculated using the declared COP when they are within the 8% tlerance, therwise using the measured COP. Fr the calculatin, the measured auxiliary mde cnsumptin and the declared values fr the mdes that have nt been tested shall be cnsidered If the calculated SCOP is nt lwer than -8% cmpared t the declared SCOP, SCOP and η are nt rerated If the calculated SCOP is lwer than -8% cmpared t the declared SCOP then, SCOP and η shall be rerated and all the declared applicatins shall be fully tested (EN r EN and EN at every part lad cnditins and ne auxiliary mde chsen by certificatin bdy). The same rerating prcedure applies t each applicatin Rerating f tested mdel rerated SCOP = measured SCOP ( ) Equatin 6 Rerated η is recalculated accrding rerated SCOP.

19 Page: 19 f 26 Rerating f the ther mdels f the sub-type and f the ther heat surces when relevant Same relative deviatin in between declared and rerated SCOP f the tested mdel shall be applied t the SCOP f the ther mdels f the sub-type and ther heat surces when relevant. η is recalculated accrding rerated SCOP. Heating test is passed if nne f the P designh and η fr all tested applicatins have been rerated Space cling a) Cnditin A test Cnditin A is tested. If heating capacity measured under cnditin A des nt deviate frm P designc frm mre than -8% then the test cntinues. If nt, the test is interrupted. The certificate hlder shall prvide a new cmplete set f declared values t the certificatin bdy and the chsen recgnised labratry within tw weeks f the interrupted test. The tests may then be restarted frm the beginning and the P designc shall be rerated as fllw: Fr the tested mdel: rerated P designc = P dc (35) Equatin 7 Fr the ther mdels f the sub-type, same deviatin in between declared and rerated P designc f the tested mdel shall be applied. When test at A temperature cnditin is cmpleted, the ther selected part lad shall be tested. b) Test at ther part lad cnditins At each part lad cnditins, measured EER shall nt be lwer than -8% cmpared t the declared EER. If every measured EER are within the tlerance, SEER is calculated using the declared EER fr each part lad cnditins and declared auxiliary mdes cnsumptin. If the calculated SEER is nt lwer than -8% cmpared t the declared SEER, then the test is ver and SEER is nt rerated. If the calculated SEER is lwer frm declared SEER by mre than -8%; then SEER shall be rerated and the rerated SEER shall be equal t the calculated SEER. SEER fr every mdel f the sub-type shall be recalculated and rerated if calculated SEER are lwer than -8% cmpared t the declared SEER If at least ne f the measured EER is lwer than -8% cmpared t the declared EER then, every nn-tested EN part lad cnditins and ne auxiliary mde cnditin (chsen by the certificatin bdy) shall be tested. SEER is then calculated using the declared EER when they are within the 8% tlerance, therwise using the

20 Page: 20 f 26 measured nes and using the measured auxiliary mde cnsumptin and the declared nes fr the nn-measured nes If the calculated SEER is nt lwer than -8% cmpared t the declared SEER, SEER is nt rerated If the calculated SEER is lwer than -8% cmpared t the declared SEER then, SEER shall be rerated. Rerating f tested mdel rerated SEER = measured SEER ( ) Equatin 8 Rerating f the ther mdels f the sub-type Same relative deviatin in between declared and rerated SEER f the tested mdel shall be applied t the SEER f the ther mdels f the sub-type. Cling test is passed if neither P designc nr SEER have been rerated. 4.3 Dmestic ht water perfrmances rerating rules The rerating rules apply independently t each declared climate. In case the test is failed and in case several heat surces are declared, all heat surces shall be rerated unless the certificate hlder asks fr a full perfrmance test n the nntested heat surce. If the test cannt fulfil the requirements f EN in term f water temperature; the certificate hlder shall prvide a new cmplete set f declared values: lad prfile; η DHW and V 40 (nly fr DHW heat pumps) t the certificatin bdy and the chsen recgnised labratry within tw weeks f the interrupted test. The tests may then be restarted frm the beginning. DHW test is passed if fr each declared climate the test has been perfrmed fr the declared lad prfile and if neither η DHW nr V 40 has been rerated, therwise the test is failed η DHW If an bserved deviatin between declared and measured η DHW exceeds -8 %, then η dhw shall be rerated. Rerating f tested mdel rerated η DHW = measured η DHW ( ) Equatin 9 Rerating f the ther mdels f the sub-type and f the ther heat surce when relevant

21 Page: 21 f 26 Same relative deviatin in between declared and rerated η DHW f the tested mdel shall be applied t the η DHW f the ther mdels f the sub-type and fr the ther heat surces when relevant V 40 nly fr dmestic ht water heat pumps If an bserved deviatin between declared and measured V 40 exceeds -3 %, then V 40 shall be rerated. Rerating f tested mdel rerated V 40 = measured V 40 ( ) Equatin 10 Rerating f the ther mdels f the sub-type and f the ther heat surce when relevant Same relative deviatin in between declared and rerated V 40 f the tested mdel shall be applied t the V 40 f the ther mdels f the sub-type and fr the ther heat surce when relevant Other EN perfrmances If a deviatin between declared and measured values is bserved fr the heating up perid, P es, reference temperature and the V 40 fr cmbinatin heat pumps; the fllwing rerating rules apply: Heating up perid Tlerance is equal t -15 min. Rerating f tested mdel rerated heating up perid = measured heating up perid 15 minutes Equatin 11 Rerating f the ther mdels f the sub-type and f the ther heat surce when relevant Same deviatin (in minutes) in between declared and rerated heating up perid f the tested mdel shall be applied t the heating up perid f the ther mdels f the sub-type and fr the ther heat surce when relevant P es Tlerance is equal t -10% Rerating f tested mdel rerated P es = measured P es Equatin 12 Rerating f the ther mdels f the sub-type and f the ther heat surce when relevant

22 Page: 22 f 26 Same relative deviatin in between declared and rerated P es f the tested mdel shall be applied t the P es f the ther mdels f the sub-type and fr the ther heat surce when relevant Reference temperature Tlerance is equal t -1K Rerating f tested mdel rerated reference temperature = measured reference temperature 1 Equatin 13 Rerating f the ther mdels f the sub-type and f the ther heat surce when relevant Same deviatin (in Kelvin) in between declared and reference temperature f the tested mdel shall be applied t the reference temperature f the ther mdels f the sub-type and fr the ther heat surce when relevant V 40 (fr cmbinatin heat pump) Tlerance is equal t -3% Rerating f tested mdel rerated V 40 = measured V 40 ( ) Equatin 14 Rerating f the ther mdels f the sub-type and f the ther heat surce when relevant Same relative deviatin in between declared and rerated V 40 f the tested mdel shall be applied t the V 40 f the ther mdels f the sub-type and fr the ther heat surce when relevant. 4.4 Sund pwer level rerating rules The rerating rules apply independently t indr and utdr units. In case the test is failed and in case several heat surces are declared, all heat surces shall be rerated unless the certificate hlder asks fr a full test n the nn-tested heat surce. Sund pwer level test is passed if neither indr unit (when relevant) nr utdr unit (when relevant) has been rerated. If measured sund pwer level is higher than declared sund pwer level frm mre than 2 db(a), then the fllwing rerating rules apply:

23 Page: 23 f 26 Rerating f tested mdel rerated sund pwer level = measured sund pwer level + 2 Equatin 15 Rerating f the ther mdels f the sub-type and f the ther heat surce when relevant Same abslute deviatin in between declared and rerated sund pwer level f the tested mdel shall be applied t the sund pwer level f the ther mdels f the sub-type and fr the ther heat surce when relevant. Sund pwer test is passed if neither utdr nr indr unit, where relevant, sund pwer level has been rerated; therwise, the test is failed. Nte 1 Example f surveillance test prcess related t paragraph Peridicity. Table 4 Surveillance test peridicity in case f multi manufacturing sites Matrix Year 1 The tested sub-types f type 3 and type 5 have t be rerated. Type 3 and type 5 have t be re-tested in the next year. Type 4 needs n surveillance test in the fllwing year.

24 Page: 24 f 26 Year 2 The tested sub-types f type 2 has t be rerated. Type 2 has t be re-tested in the next year. Year 3 The tested sub-types f type 1 has t be rerated. Type 1 has t be re-tested in the next year. All sub-types f the tested type 2 have t be rerated. Type 2 has t be re-tested in the next year. Type 4 needs n surveillance test in the fllwing year. Year 4

25 Page: 25 f 26 Chart 1 Surveillance test prcess Admissin Year 1 Year 2 Year 3 1 test 1.1 test Pass 1.1: 0 test Fail 1.1: 1 test

26