a. The power required to drive the compressor; b. The inlet and output pipe cross-sectional area. [Ans: kw, m 2 ] [3.34, R. K.

Size: px
Start display at page:

Download "a. The power required to drive the compressor; b. The inlet and output pipe cross-sectional area. [Ans: kw, m 2 ] [3.34, R. K."

Transcription

1 CHAPTER 2 - FIRST LAW OF THERMODYNAMICS 1. At the inlet to a certain nozzle the enthalpy of fluid passing is 2800 kj/kg, and the velocity is 50 m/s. At the discharge end the enthalpy is 2600 kj/kg. The nozzle is horizontal and there is negligible heat loss from it. a. Find the velocity at exit of the nozzle. b. If the inlet area is 900 cm 2 and the specific volume at inlet is m 3 /kg, find the mass flow rate. c. If the specific volume at the nozzle exit is m 3 /kg, find the exit area of nozzle. [Ans: m/s, kg/s, cm 2 ] [3.42, R. K. Rajput] 2. In a gas turbine unit, the gases flow through the turbine is 15 kg/s and the power developed by the turbine is kw. The enthalpies of gases at the inlet and outlet are 1260 kj/kg and 400 kj/kg respectively, and the velocity of gases at the inlet and outlet are50 m/s and 110 m/s respectively. Calculate: a. The rate at which heat is rejected to the turbine, and b. The area of the inlet pipe given that the specific volume of the gases at the inlet is 0.45 m 3 /kg. [Ans: 828 kw, m 2 ] [3.33, R. K. Rajput] 3. The mass flow rate of steam into a steam turbine is 1.5 Kg/s and heat loss from the turbine is 8.5 KW. The steam is entering the turbine at the pressure of 2MPa, temperature 350 C, Velocity 50 m/s, elevation 6 m/s and is leaving the turbine at a pressure of 0.1 MPa, quality of 100%, velocity of 200 m/s, elevation of 3 m/s. Determine power output of turbine. [GTU, JUN-2015][Ans: 4. In an air compressor air flows steadily at the rate of 0.5 kg/s through an air compressor. It enters the compressor at 6 m/s with a pressure of 1 bar and a specific volume of 0.85 m 3 /kg and leaves at 5 m/s with a pressure of 7 bar and a specific volume of 0.16 m 3 /kg. The internal energy of the air leaving is 90 kj/kg greater than that of the air entering. Cooling water in a jacket surrounding the cylinder absorbs heat from the air at the rate of 60 kj/s. Calculate: a. The power required to drive the compressor; b. The inlet and output pipe cross-sectional area. [Ans: kw, m 2 ] [3.34, R. K. Rajput] Darshan Institute of Engineering and Technology, Rajkot 1

2 CHAPTER 2 - FIRST LAW OF THERMODYNAMICS 5. A centrifugal pump delivers 50 kg of water per second. The inlet and outlet pressures are 1 bar and 4.2 bar respectively. The suction is 2.2 m below the centre of the pump and delivery is 8.5 m above the centre of the pump. The suction and delivery pipe diameters are 20 cm and 10 cm respectively. Determine the capacity of the electric motor to run the pump. [Ans: 22.2 kw] [3.45, R. K. Rajput] 6. Air at a temperature of 20 C passes through a heat exchanger at a velocity of 40 m/s where its temperature is raised to 820 C. It then enters a turbine with same velocity of 40 m/s and expands till the temperature falls to 620 C. On leaving the turbine, the air is taken at a velocity of 55 m/s to a nozzle where it expands until the temperature has fallen to 510 C. If the air flow rate is 2.5 kg/s, calculate: a. Rate of heat transfer to the air in the heat exchanger; b. The power output from the turbine, assuming no heat loss; c. The velocity at exit from the nozzle, assuming no heat loss. (Take the enthalpy of air as h = cpt, where cp is the specific heat equal to kj/kg- C and t is the temperature.) [Ans: 2010 kj/s, kw, m/s] [3.47, R. K. Rajput] 7. The air speed of a turbojet engine in flight is 270 m/s. Ambient air temperature is - 15 C. Gas temperature at outlet of nozzle is 600 C. Corresponding enthalpy values for air and gas are respectively 260 and 912 KJ/kg. Fuel-air ratio is Chemical energy of the fuel is 44.5 MJ/kg. Owing to incomplete combustion 5% of the chemical energy is not released in the reaction. Heat loss from the engine is 21 KJ/kg of air. Calculate the velocity of the exhaust jet. [Ans: 560m/s] [5.7, P. K. Nag] Darshan Institute of Engineering and Technology, Rajkot 2

3 CHAPTER 3 2 nd LAW OF THERMODYNAMICS 1. A reversed Carnot cycle operates at either a refrigerator or heat pump. In either case, the power input is 20.8 kw. Calculate the quantity of heat extracted from the cold body for either type of machine. In both case 3500 kj/min heat is delivered by the machine. In case of the refrigerator the heat is transferred to the surroundings while in case of heat pump, the space is to be heated. What is their respective coefficient of performances? If the temperature of cold body is 0 C for the refrigerator and 5 C for heat pump what will be respective temperatures of surrounding for refrigerator and heated space for heat pump? What reduction in heat rejection temperatures would be achieved by doubling the COP for same cold body temperature? GTU Jun A Carnot engine receives 4000 KJ as heat addition at C and rejects energy at triple point of water. Calculate (1) thermal efficiency (2) The net work output in KJ, if the efficiency of an irreversible engine is 70 % of Carnot engine. Find the % change in heat rejected for the same input and fluid temperature. GTU Nov An engine manufacturer claims to have developed a heat engine with following specifications: Power developed Fuel burnt Heating value of fuel Temperature limits = 75 kw = 5 kg/hr = kj/kg = 1000 K and 400 K Is the claim of an engine manufacturer true or false? Provide your explanation. [Answer: Claim is false] D.S Kumar 211/ A heat engine is supplied with 2512 kj/min of heat at 650⁰C. Heat rejection takes place at 100⁰C. Specify which of the following heat rejections represents reversible, irreversible and impossible results: D.S Kumar 217/7.21 (i) 867 kj/min, (ii) 1015 kj/min, (iii) 1494 kj/min] [Answer: (1) Impossible cycle; (2) Reversible cycle; (3) Irreversible cycle] 5. A reversible engine receives heat from two thermal reservoirs maintained at constant temperature of 750 K and 500 K. The engine develops 100 kw and rejects 3600 kj/min of heat to a heat sink at 250 K. Determine thermal efficiency of the engine and heat supplied by each thermal reservoir. D.S Kumar 219/7.25 Darshan Institute of Engineering and Technology, Rajkot 1

4 CHAPTER 3 2 nd LAW OF THERMODYNAMICS [Answer: (1) ηth = 62.5%; (2) Heat supplied by source at 750 K = 7200 kj/min, heat supplied at 500 K = 2400 kj/min] 6. Two reversible engines A and B are arranged in series. Engine A rejects heat directly to engine B. Engine A receives 200 kj at temperature of 421⁰C from the hot source while engine B is in communication with a cold sink at a temperature of 5⁰C. If the work output of A is twice that of B. Find (1) intermediate temperature between A and B; (2) efficiency of each engine and (3) heat rejected to the sink. [Answer: (1) T2 = K; (2) ηa = 39.96%, ηb = 33.28%; (3) Q2 = kj, Q3 = kj] D.S Kumar 225/ A reversible heat engine operates between 875 K and 310 K and drives a reversible refrigerator operating between 310 K and 255 K. The engine receives 2000 kj of heat and the net work output from the arrangement equals 350 kj. Make calculations for the cooling effect. D.S Kumar 230/7.38 [Answer: (1) Cooling effect, Q3 = kj] 8. A reversible heat engine operates within the higher and lower temperature limits of 1400K and 400K respectively. The entire output from this engine is utilized to operate a heat pump. The pump works on reversed Carnot cycle, extracts heat from a reservoir at 300K and delivers it to the reservoir at 400K. If 100 KJ/s of net heat is supplied to the reservoir at 400K, calculate the heat supplied by the reservoir at 1400K. GTU Oct 2012 Darshan Institute of Engineering and Technology, Rajkot 2

5 CHAPTER 4 ENTROPY 1. A lump of steel of mass 8 kg at 1000 K is dropped in 80 kg of oil at 300 K. Find out entropy change of steel, oil and the universe. Take specific heats of steel and oil as 0.5 kj/kg K and 3.5 kj/kg K respectively. D.S Kumar 248/8.6 [Answer: (ds)st = kj/k, (ds)oil = kj/k, (ds)uni = kj/k] 2. An inventor claims that he has developed a heat engine which absorbs 1200 kj and 800 kj of heat from reservoirs at 800 K and 600 K respectively and rejects 600 kj and 200 kj of heat to reservoirs at 400 K and 300 K. The engine is further stated to give an output equivalent to 1200 kj. Determine whether the engine suggested by the inventor is theoretically possible. D.S Kumar 256/8.18 [Answer: Suggested claim is theoretically not possible] 3. The connections of a reversible engine to three sources at 400 K, 300 K and 200 K. The engine draws 1200 kj of work. Determine: (1) The amount and directions of heat reservoirs with the other heat sources, (2) Make calculations for the entropy changes due to each of the heat interactions with the engine, (3) How much entropy change occurs for the cycle? [Answer: (1) Q2 = kj, Q3 = -200 kj; (2) ds1 = -3 kj/k, ds2 = +4 kj/k, ds3 = -1 kj/k; (3) dscycle = 0 kj/k] D.S Kumar 257/8.19 Entropy Change during Non Flow Thermodynamic Processes 4. A volume of 0.14 m 3 of air at 1 bar and 90:C is compressed to m 3 according to the law of pv 1.3 = C. Heat is then added at constant volume until the pressure is 66 bar. Determine: (1) Heat exchange with cylinder walls during compression and, (2) Entropy change during each portion of process. Take γ = 1.4, R = kj/kg K. [Answer: (1) Q1-2 = kj; (2) ds1-2 = kj/k, ds2-3 = kj/k] 5. 1 m 3 of air is heated reversibly at constant pressure from 290 K to 580 K and is then cooled reversibly at constant volume back to initial temperature. If the initial pressure is 1 bar. Workout the net heat flow and overall (net) change in entropy. Represent the processes on T-s diagram. Take Cp = kj/kg K and R = kj/kg K. [Answer: (1) Qnet = kj/k; (2) dsnet = kj/k] D.S Kumar 271/ kg of air at 150 kpa pressure and 360 K temperature is compressed polytropically to pressure 750 kpa according to the pv 1.2 = C. Subsequently the air is cooled to initial temperature at constant pressure. This is followed by expansion at constant temperature till the original pressure of 150 kpa is reached. Sketch the cycle on p-v and T-s plot. Determine work done, heat transfer, and change in entropy during each process. D.S Kumar 272/8.33 [Answer: Process 1-2: W1-2 = kj, Q1-2 = kj, ds1-2 = kj/k; Process 2-3: W2-3 = kj, Q2-3 = kj, ds2-3 = kj/k; Process 3-1: W3-1 = kj, Q3-1 = kj, ds3-1 = kj/k] Darshan Institute of Engineering and Technology, Rajkot 1

6

7 Available Energy and Unavailable Energy CHAPTER 5 ENERGY 1. Calculate availability (available energy) and unavailability (unavailable energy) of a system that absorbs kj of heat from a heat source at 500 K temperature while the environment at 290 K temperature. D.S Kumar 287/9.1 [Answer: Availability = 6300 kj, Unavailability = 8700 kj] 2. A source at 1000 K is available for transfer of heat at the rate of 100 kw to a system at 500 K. If these temperatures remain constant. Determine (1) entropy production during heat transfer, (2) the increase in unavailable energy. Take ambient temperature as 300 K. [Answer: (1) dsnet = 6 kj/k min, (2) in UAE = 1800 kj/min] D.S Kumar 289/9.6 Decrease in Available Energy due to Heat Transfer at Finite Temperature Difference 3. A system at 450 K receives 225 kj/s of heat energy from a source at 1500 K, and the temperatures of both the system and source remains constant during heat transfer process. Represent process on T-s diagram. Determine, (1) the net change in entropy, (2) available energy of heat source and system, and (3) decrease in available energy. [Answer: (1) dsnet = kj/s K, (2) AE1 = 180 kj/s, AE2 = 75 kj/s, (3) in AE = 105 kj (or in UAE)] D.S Kumar 292/ kg of water at 90:C is mixed with 30 kg of water at 30:C and the pressure remains constant during the mixing operation. Calculate the decrease in available energy. It may be presumed that the surroundings are at 10:C temperature and for water Cpw = kj/kg K. [Answer: in AE = kj] D.S Kumar 291/ Kg of water undergoes transformation from initial saturated vapour at 150 C, velocity of 25 m/s and elevation of 10 m to saturated liquid at 20 C, velocity of 10m/s and elevation of 3m. determine the availability of for initial state, final state and change if availability considering environment to be taken at 0.1 MPa and 25 C and g=9.8 m/s2 GTU Jun 2010 Availability for Closed System 6. One kg of air is contained in a piston cylinder assembly at 10 bar pressure and 500 K temperature. The piston moves outwards and the air expands to 2 bar pressure and Darshan Institute of Engineering and Technology, Rajkot 1

8 CHAPTER 5 ENERGY 350 K temperature. Calculate: (1) the availability in the initial and final states, (2) the maximum useful work, and (3) the irreversibility for the system. Assume that system is insulated and the environment conditions are 1 bar and 290 K. Further for air, R = kj/kg K, Cv = kj/kg K. [Answer: (1) A1 = kj, A2 = kj, (2) Wmax = kj, (3) irreversibility (I) = kj] D.S Kumar 296/ A closed system contains 2 kg of air and during an adiabatic expansion process; there occurs a change in its pressure from 500 kpa to 100 kpa and its temperature from 350 K to 320 K. If the volume doubles during the process. Calculate: (1) maximum work, (2) change in availability and (3) irreversibility. Take T0 = 300 K and P0 = 10 kpa. D.S Kumar 297/9.15 [Answer: (1) Wmax = kj, (2) A1 A2 = kj, (3) Irreversibility = kj] 8. Two Kg of air at 500 KPa, 80 C expands adiabatically in a closed system until its volume is doubled and its temperature becomes equal to that of surrounding which is at 100 kpa, 5 C. For this process, determine (a) maximum work, (b) Change in availability and irreversibility, for air take Cv =0.718 kj/kg K, R=0.287 kj/kg K Availability for Open (steady flow) System GTU Jun The air in a steady flow enters the system at pressure 12 bar and temperature 180:C with a velocity of 100 m/s. The corresponding values at exit from the system are 1.5 bar, 20:C and 50 m/s. if the surrounding are at 1 bar and 20:C. Determine: (1) the reversible work and actual work assuming process to be adiabatic, (2) irreversibility & effectiveness of the system. D.S Kumar 300/9.17 [Answer: (1) Wrev = kj/kg, Wact = kj/kg (2) Irreversibility = kj/kg, effectiveness (Є) = 92.94%] 10. A single stage air turbine is to be operated with an inlet pressure and temperature of 6 bar and 800 K. The outlet pressure and temperature are 1.0 bar and 500 K. During expansion, the turbine losses 25 kj/kg to the surroundings which are at 1 bar and 300 K. For unit mass flow rate, determine, (1) decrease in availability, (2) the maximum work, and, (3) irreversibility. For air take R = kj/kg K, Cp = kj/kg K. D.S Kumar 300/9.16 [Answer: (1) in AE = kj/kg, (2) Wmax = kj/kg, (3) irreversibility (I) = kj/kg] Darshan Institute of Engineering and Technology, Rajkot 2

9 CHAPTER 6 VAPOR POWER CYCLES 1. A steam power plant operates on the Carnot cycle using dry steam at 17.5 bar. The exhaust takes place at bar into condenser. The steam consumption is 20 kg/min. Calculate: a. Power developed in the cycle b. The efficiency of the cycle [Ans: KW, 34.56%][12.1; Mahesh Rathore] 2. A power generating plant uses steam as working fluid and operates on an ideal Carnot cycle. Dry saturated steam at 17.5 bar pressure is supplied to the engine and it expands isentropically to a condenser pressure of 0.07 bar. Assuming the liquid to be saturated at entry to the boiler, make calculations for the work ratio, thermal efficiency and specific steam consumption. [Ans: 0.823, %, 5.39 kg/kwh] [15.2, D. S. Kumar] 3. A steam turbine working on Rankine cycle is supplied with dry saturated steam at 25 bar and the exhaust takes place at 0.2 bar. For a steam flow rate of 10 kg/s, determine: a. Quality of steam at the end of expansion. b. Turbine shaft work. c. Power required to drive the pump. d. Work ratio and Rankine efficiency. e. Heat flow in the condenser. [Ans: 0.776, kj/kg, kw, 0.996, 28.9 %, kw] [15.4, D. S. Kumar] 4. In a thermal power plant operating on an ideal Rankine cycle, superheated steam produced at 5 MPa and 500 C is fed to a turbine where it expands to the condenser pressure of 10 kpa. If the net power output of the plant is to be 20 MW, determine: a. Heat added in the boiler per kg of water. b. Thermal efficiency of the cycle. c. Mass flow rate of steam in kg/s. d. Mass flow rate of cooling water in the condenser if the cooling water enters the condenser at 25 C and leaves at 35 C. [Ans: kj/kg, %, kg/s, kg/s] [15.7, D. S. Kumar] Darshan Institute of Engineering and Technology, Rajkot 1

10 CHAPTER 6 VAPOR POWER CYCLES 5. Steam at 20 bar, 360 C is expanded in a steam turbineto 0.08 bar. It then enters a condenser, where it is condensed to saturated liquid water. The pump feeds back the water into the boiler. (a) Assuming ideal processes, find per kg of steam the net work and the cycle efficiency. (b) If the turbine and the pump have each 80% efficiency, find the percentage reduction in the net work and cycle efficiency. [Ans: kj/kg, 32.5%, 20.1%, 20.1%] [12.2, P. K. Nag] 6. A steam power plant uses the following cycle: Steam at boiler outlet 150 bar& 550 C Reheat at 40 bar to 550 C Condenser at 0.1 bar. Using the Mollier chart and assuming ideal processes, find the (a) Quality of steam at turbine exhaust, (b) Cycle efficiency and (c) Steam rate. [Ans: 0.88, 43.9%, 2.18 kg/kwh] [12.4, P. K. Nag] 7. In a single heater regenerative cycle the steam enters the turbine at 30 bar, 400 C and the exhaust pressure is 0.1 bar. The feed water heater is a direct contact type which operates at 5 bar. Find: a. The efficiency and the steam rate of the cycle. b. The increase in mean temperature of heat addition, efficiency and steam rate as compared to the Rankine cycle (without regeneration). Pump work may be neglected. [Ans: 36.08%, 3.85 kg/kwh, 27.4 C, 1.9%, 0.39 kg/kwh] [12.13, R. K. Rajput] 8. An ideal steam power cycle combines the reheat and regenerative cycles. Steam is supplied to the turbine at 17.5 bar and 300 C. the steam expands isentropically to a pressure of 8.5 bar, is reheated at constant pressure to 290 C and isentropic expansion follows to a condenser pressure of 0.04 bar. Steam is extracted at 1 bar for the purpose of feed water heating. The bled steam raises the temperature of feed water to 70 C. Assuming the temperature of hot well 26 C, determine the thermal efficiency of the steam plant. [Ans: 34.1%] [15.12, D. S. Kumar] Darshan Institute of Engineering and Technology, Rajkot 2

11 CHAPTER 7 GAS POWER CYCLES 1. A Carnot cycle has lowest pressure and temperature equal to 1bar & 20 C. Pressure after Isothermal compression is 4 bar. Pressure after isentropic compression is 12 bar and after Isothermal heat addition process is 6 bar. Calculate: a. The highest temperature in the cycle. b. The change in entropy during Isothermal expansion. c. Heat added to the cycle. d. Heat rejected by the cycle [Dec 2010] 2. An engine uses 6.5 Kg of oil per hour of calorific value of 30,000 kj/kg. If the Brake power of engine is 22 kw and mechanical efficiency is 85% calculate (a) indicate thermal efficiency (b) Brake thermal efficiency (c) Specific fuel consumption in Kg/B.P/hr. [June-2010] 3. An engine working on Otto cycle has a volume of 0.45 m 3, pressure 1 bar and temperature 30 C at the beginning of compression stroke. At the end of compression stroke, the pressure is 11 bar. 210 kj of heat is added at constant volume. Determine: a. Pressures, temperatures and volumes at salient points in the cycle. b. Percentage clearance. c. Efficiency. d. Mean effective pressure. e. Ideal power developed by the engine if the number of working cycles per minute is 210. Assume the cycle is reversible. [Ans: 600 K, m 3, 1172 K, bar, m 3, 1.97 bar, K, 0.45 m 3, %, 49.5 %, bar, 364 kw] [21.13, R. K. Rajput] 4. In an Otto cycle air at start of isentropic compression is at 20 C and 110kPa. If clearance volume is 20% of the swept volume and temperature at end of constant volume heat addition is 1400 C, find the air standard efficiency and mean effective pressure in kpa. Take. [June-2011] 5. The following data pertains to a C.I. engine working on air standard Diesel cycle: Cylinder bore = 15 cm; Stroke length = 25 cm, Clearance volume = 400 cm 3 Calculate the air standard efficiency of the engine if fuel injection takes place at constant pressure for 5 % of the stroke. How this efficiency value will be affected if the fuel supply continues up to 8 % of the stroke? [Ans: %, 2 %] [12.18, D. S. Kumar] 6. A four stroke engine working on Diesel cycle has a piston diameter of 25 cm, a stroke of 40 cm and a clearance volume of 1200 cc. The fuel injection takes place for 5 % of stroke. If the induction pressure corresponds to 1 bar and engine turns 5 Darshan Institute of Engineering and Technology, Rajkot 1

12 CHAPTER 7 GAS POWER CYCLES rev/sec, find the air standard efficiency, mean effective pressure and power developed. [Ans: 63.5 %, 6.03 bar, kw] [12.24, D. S. Kumar] 7. An engine with 200 mm cylinder diameter and 300 mm stroke works on theoretical Diesel cycle. The initial pressure and temperature of air used are 1 bar and 27 C. The cut-off is 8% of the stroke. Determine: a. Pressures, temperatures and volumes at all salient points. b. Theoretical air standard efficiency. c. Mean effective pressure. d. Power of the engine if the working cycles per minute are 380. Assume that compression ratio is 15 and working fluid is air. Consider all conditions to be ideal. [Ans: m3, bar, K, m 3, m 3, K, bar, K, 59.8 %, bar, kw] [21.21, R. K. Rajput] 8. The compression ratio for a single cylinder engine operating on Dual cycle is 9. The maximum pressure in the cylinder is limited to 60 bar. The pressure and temperature of the air at the beginning of the cycle are 1 bar and 30 C. Heat is added during constant pressure process up to 4 percent of the stroke. Assuming the cylinder diameter and stroke length as 250 mm and 300 mm respectively, determine: a. The air standard efficiency of the cycle. b. The power developed if the number of working cycles are 3 per second. Take for air Cv = 0.71 kj/kg-k and Cp = 1.0 kj/kg-k. [Ans: %, 51 kw] [21.25, R. K. Rajput] 9. In a gas turbine plant working on Brayton cycle, the air at inlet is 27 C, 0.1 MPa. The pressure ratio is 6.25 and the maximum temperature is 800 C. The turbine and compressor efficiencies are each 80 %. Find compressor work, turbine work, heat supplied, cycle efficiency and turbine exhaust temperature. Mass of air may be considered as 1 kg. Draw T-s diagram. [Ans: kj/kg, kj/kg, kj/kg, %, K] [21.38, R. K. Rajput] 10. In an air standard Brayton cycle, the minimum temperature T1 is governed by the ambient atmosphere and the maximum temperature T3 is dictated by the material of construction of the turbine blades. For fixed values of T1 and T3, determine the pressure ratio rp for obtaining maximum net work per unit mass of air undergoing the cyclic change. Consider a gas turbine plant operating on Brayton cycle with minimum and maximum temperature limits being 300 K and 1000 K. What would be the optimum Darshan Institute of Engineering and Technology, Rajkot 2

13 CHAPTER 7 GAS POWER CYCLES value of pressure ratio if the turbine is to be operated for maximum power output? For the pressure ratio thus calculated, determine the plant efficiency, work ratio and specific power output. Assume working substance to be air and expansion and compression to be truly isentropic. Comment on the results obtained. [Ans: 8.22, %, , kw] [12.40, D. S. Kumar] 11. A simple open cycle gas turbine takes in air at atmospheric pressure and 15 C and compresses air in the compressor up to 12bar. Then air enters the combustion chamber and is heated to maximum temp of 1350 C, then it enter the turbine and expands to atmospheric pressure. If the isentropic efficiency of compressor and turbine is 0.86, combustion efficiency is 0.97, fall of pressure through the combustion system is 0.3bar, Cp for both air and gas 1.005, γ=1.4. Determine the flow of air and gas for net power of 200MW developed. Calculate also the heat supplied per kg of air, work ratio, thermal efficiency and specific fuel consumption if C.V. of fuel is kj/kg. [Ans: 560kg/s & 13.64kg/s, kJ/kg of air, 51.05%, 34.9%, 0.245kg/kWh] [17.5; R Yadav] 12. In a gas turbine plant, the air is at 10 0 C and 1bar is compressed to 12bar with compression efficiency of 80%. The air is heated in the regenerator and the combustion chamber till its temp raised is to C, and during the process the pressure falls by 0.2 bar. The air then expanded in the turbine and passes to regenerator which has 75% effectiveness, and causes a pressure drop of 0.2bar. If the isentropic efficiency of the turbine is 85%, determine the thermal efficiency of the plant. [Ans: 42.69%] [17.7; R Yadav] Darshan Institute of Engineering and Technology, Rajkot 3

CHAPTER 1 BASIC CONCEPTS THEORY

CHAPTER 1 BASIC CONCEPTS THEORY CHAPTER 1 BASIC CONCEPTS THEORY 1. Explain briefly the following terms with diagram (wherever necessary): a) Thermodynamic System, Surroundings & Boundary b) Control Volume & Control Surface c) Intensive

More information

CHAPTER 1 BASIC CONCEPTS

CHAPTER 1 BASIC CONCEPTS GTU Paper Analysis CHAPTER 1 BASIC CONCEPTS Sr. No. Questions Jan 15 Jun 15 Dec 15 May 16 Jan 17 Jun 17 Nov 17 May 18 Differentiate between the followings; 1) Intensive properties and extensive properties,

More information

ME ENGINEERING THERMODYNAMICS UNIT III QUESTION BANK SVCET

ME ENGINEERING THERMODYNAMICS UNIT III QUESTION BANK SVCET 1. A vessel of volume 0.04m 3 contains a mixture of saturated water and steam at a temperature of 250 0 C. The mass of the liquid present is 9 kg. Find the pressure, mass, specific volume, enthalpy, entropy

More information

Chapter 1 Basic Concepts

Chapter 1 Basic Concepts Jan 15 Jun 15 Chapter 1 Basic Concepts GTU Paper Analysis (New Syllabus) Sr. No. Questions Differentiate between the followings; 1) Intensive properties and extensive properties, 2) Point function and

More information

Reg. No. : Question Paper Code : B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER Second Semester

Reg. No. : Question Paper Code : B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER Second Semester ws15 Reg. No. : Question Paper Code : 27425 B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER 2015. Time : Three hours Second Semester Marine Engineering MV 6201 MARINE ENGINEERING THERMODYNAMICS (Regulations

More information

Practice Final Exam (A) Six problems. (Open-book, HW solutions, and notes) (Plus /minus 10 % error acceptable for all numerical answers)

Practice Final Exam (A) Six problems. (Open-book, HW solutions, and notes) (Plus /minus 10 % error acceptable for all numerical answers) ME 3610 Practice Final Exam (A) Six problems. (Open-book, HW solutions, and notes) (Plus /minus 10 % error acceptable for all numerical answers) (18 points) 1. A gasoline engine operating on the ideal

More information

Chapters 5, 6, and 7. Use T 0 = 20 C and p 0 = 100 kpa and constant specific heats unless otherwise noted. Note also that 1 bar = 100 kpa.

Chapters 5, 6, and 7. Use T 0 = 20 C and p 0 = 100 kpa and constant specific heats unless otherwise noted. Note also that 1 bar = 100 kpa. Chapters 5, 6, and 7 Use T 0 = 20 C and p 0 = 100 kpa and constant specific heats unless otherwise noted. Note also that 1 bar = 100 kpa. 5-1. Steam enters a steady-flow device at 16 MPa and 560 C with

More information

R13. II B. Tech I Semester Regular/Supplementary Examinations, Oct/Nov THERMODYNAMICS (Com. to ME, AE, AME) Time: 3 hours Max.

R13. II B. Tech I Semester Regular/Supplementary Examinations, Oct/Nov THERMODYNAMICS (Com. to ME, AE, AME) Time: 3 hours Max. SET - 1 1. a) Discuss about PMM I and PMM II b) Explain about Quasi static process. c) Show that the COP of a heat pump is greater than the COP of a refrigerator by unity. d) What is steam quality? What

More information

Chapter 1 STEAM CYCLES

Chapter 1 STEAM CYCLES Chapter 1 STEAM CYCLES Assoc. Prof. Dr. Mazlan Abdul Wahid Faculty of Mechanical Engineering Universiti Teknologi Malaysia www.fkm.utm.my/~mazlan 1 Chapter 1 STEAM CYCLES 1 Chapter Objectives To carry

More information

Problems in chapter 9 CB Thermodynamics

Problems in chapter 9 CB Thermodynamics Problems in chapter 9 CB Thermodynamics 9-82 Air is used as the working fluid in a simple ideal Brayton cycle that has a pressure ratio of 12, a compressor inlet temperature of 300 K, and a turbine inlet

More information

EXTRA CREDIT OPPORTUNITY: Due end of day, Thursday, Dec. 14

EXTRA CREDIT OPPORTUNITY: Due end of day, Thursday, Dec. 14 EXRA CREDI OPPORUNIY: Due end of day, hursday, Dec. 4 his extra credit set of questions is an opportunity to improve your test scores (including an insurance policy for your final exam grade). here are

More information

Lecture No.1. Vapour Power Cycles

Lecture No.1. Vapour Power Cycles Lecture No.1 1.1 INTRODUCTION Thermodynamic cycles can be primarily classified based on their utility such as for power generation, refrigeration etc. Based on this thermodynamic cycles can be categorized

More information

MECHANICAL ENGINEERING DEPARTMENT, OITM

MECHANICAL ENGINEERING DEPARTMENT, OITM Sem.:4 th Subject: Energy Conversion Paper: ME-201E UNIT-1 Q1. Explain the seismometer with its working principle. (Important Question) (20) Q2. Classify the fuels and define calorific value of fuels.

More information

R13 SET - 1 '' ''' '' ' '''' Code No: RT31035

R13 SET - 1 '' ''' '' ' '''' Code No: RT31035 R13 SET - 1 III B. Tech I Semester Regular/Supplementary Examinations, October/November - 2016 THERMAL ENGINEERING II (Mechanical Engineering) Time: 3 hours Max. Marks: 70 Note: 1. Question Paper consists

More information

Eng Thermodynamics I - Examples 1

Eng Thermodynamics I - Examples 1 Eng3901 - Thermodynamics I - Examples 1 1 pdv Work 1. Air is contained in a vertical frictionless piston-cylinder. The mass of the piston is 500 kg. The area of the piston is 0.005 m 2. The air initially

More information

Eng Thermodynamics I - Examples 1

Eng Thermodynamics I - Examples 1 Eng3901 - Thermodynamics I - Examples 1 1 pdv Work 1. Air is contained in a vertical frictionless piston-cylinder. The mass of the piston is 500 kg. The area of the piston is 0.005 m 2. The air initially

More information

AREN 2110: Thermodynamics Spring 2010 Homework 7: Due Friday, March 12, 6 PM

AREN 2110: Thermodynamics Spring 2010 Homework 7: Due Friday, March 12, 6 PM AREN 2110: Thermodynamics Spring 2010 Homework 7: Due Friday, March 12, 6 PM 1. Answer the following by circling the BEST answer. 1) The boundary work associated with a constant volume process is always

More information

MUZAFFARPUR INSTITUTE OF TECHNOLOGY COURSE FILE OF THERMODYNAMICS FACULTY NAME: AMIT KUMAR ASSISTANT PROFESSOR DEPARTMENT OF MECHANICAL ENGINEERING

MUZAFFARPUR INSTITUTE OF TECHNOLOGY COURSE FILE OF THERMODYNAMICS FACULTY NAME: AMIT KUMAR ASSISTANT PROFESSOR DEPARTMENT OF MECHANICAL ENGINEERING MUZAFFARPUR INSTITUTE OF TECHNOLOGY COURSE FILE OF THERMODYNAMICS FACULTY NAME: AMIT KUMAR ASSISTANT PROFESSOR DEPARTMENT OF MECHANICAL ENGINEERING CONTENTS 1. Cover Page& Content 2. Vision of the Department

More information

Faculty of Engineering 2 nd year 2016 Mechanical Engineering Dep. Final-exam (code: M 1222)

Faculty of Engineering 2 nd year 2016 Mechanical Engineering Dep. Final-exam (code: M 1222) Benha University Thermodynamics II Faculty of Engineering 2 nd year 2016 Mechanical Engineering Dep. Final-exam (code: M 1222) Time: Three Hours (attempt all questions) (assume any missing data) Question1

More information

S.E. (Mechanical) (First Semester) EXAMINATION, 2012 APPLIED THERMODYNAMICS (2008 PATTERN) Time : Three Hours Maximum Marks : 100

S.E. (Mechanical) (First Semester) EXAMINATION, 2012 APPLIED THERMODYNAMICS (2008 PATTERN) Time : Three Hours Maximum Marks : 100 Total No. of Questions 12] [Total No. of Printed Pages 8 Seat No. [4162]-111 S.E. (Mechanical) (First Semester) EXAMINATION, 2012 APPLIED THERMODYNAMICS (2008 PATTERN) Time : Three Hours Maximum Marks

More information

- 2 - SME Q1. (a) Briefly explain how the following methods used in a gas-turbine power plant increase the thermal efficiency:

- 2 - SME Q1. (a) Briefly explain how the following methods used in a gas-turbine power plant increase the thermal efficiency: - 2 - Q1. (a) Briefly explain how the following methods used in a gas-turbine power plant increase the thermal efficiency: i) regenerator ii) intercooling between compressors (6 marks) (b) Air enters a

More information

Chapter 10 POWER CYCLES. Department of Mechanical Engineering

Chapter 10 POWER CYCLES. Department of Mechanical Engineering Chapter 10 VAPOR AND COMBINED POWER CYCLES Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University it 2 Objectives Analyze vapor power cycles in which h the working fluid is alternately

More information

Code No: RR Set No. 1

Code No: RR Set No. 1 Code No: RR310303 Set No. 1 III B.Tech I Semester Regular Examinations, November 2006 THERMAL ENGINEERING-II (Mechanical Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions

More information

Engineering Thermodynamics

Engineering Thermodynamics Unit 61: Engineering Thermodynamics Unit code: D/601/1410 QCF level: 5 Credit value: 15 Aim This unit will extend learners knowledge of heat and work transfer. It will develop learners understanding of

More information

PAPER-I (Conventional)

PAPER-I (Conventional) 1. a. PAPER-I (Conventional) 10 kg of pure ice at 10 ºC is separated from 6 kg of pure water at +10 O C in an adiabatic chamber using a thin adiabatic membrane. Upon rupture of the membrane, ice and water

More information

Vapor and Combined Power Cycles

Vapor and Combined Power Cycles 9 CHAPTER Vapor and Combined Power Cycles 9-1 The Simple Ideal Rankine Cycle The 9-2 Rankine Cycle: Actual Vapor Power Deviation and Pump and Turbine Irreversibilities (a) Deviation of actual vapor power

More information

2. The data at inlet and exit of the turbine, running under steady flow, is given below.

2. The data at inlet and exit of the turbine, running under steady flow, is given below. 3 rd week quiz 1. Identify the correct path of fluid flow in a steam power plant. a) Steam turbine-pump-boiler-condenser. b) Economizer- evaporator- superheater. c) Pump-turbine-condenser-evaporator. d)

More information

Chapter 9: Vapor Power Systems

Chapter 9: Vapor Power Systems Chapter 9: Vapor Power Systems Table of Contents Introduction... 2 Analyzing the Rankine Cycle... 4 Rankine Cycle Performance Parameters... 5 Ideal Rankine Cycle... 6 Example... 7 Rankine Cycle Including

More information

CERTIFICATES OF COMPETENCY IN THE MERCHANT NAVY MARINE ENGINEER OFFICER

CERTIFICATES OF COMPETENCY IN THE MERCHANT NAVY MARINE ENGINEER OFFICER CERTIFICATES OF COMPETENCY IN THE MERCHANT NAVY MARINE ENGINEER OFFICER EXAMINATIONS ADMINISTERED BY THE SCOTTISH QUALIFICATIONS AUTHORITY ON BEHALF OF THE MARITIME AND COASTGUARD AGENCY STCW 95 CHIEF

More information

Second Law of Thermodynamics

Second Law of Thermodynamics Second Law of Thermodynamics Content Heat engine and its efficiency. Reversible and irreversible processes. The Carnot machine. Kelvin Planck Statement. Refrigerator and Coefficient of Performance. Statement

More information

Ph.D. Qualifying Exam. Thermodynamics. Spring 2011

Ph.D. Qualifying Exam. Thermodynamics. Spring 2011 Student Code Number: Ph.D. Qualifying Exam Thermodynamics Spring 2011 Professor Tonghun Lee Professor Abraham Engeda Directions: Open Book (only one book allowed) and closed notes Answer all six questions

More information

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM IV (ME-41, 42,43 & 44)] QUIZ TEST-1 (Session: )

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM IV (ME-41, 42,43 & 44)] QUIZ TEST-1 (Session: ) QUIZ TEST-1 Q.1. In a stage of an impulse turbine provided with a single row wheel, the mean diameter of the blade ring is 80cm and the speed of the rotation is 3000rpm. The steam issues from the nozzle

More information

HW-1: Due Tuesday 13 Jun 2017 by 2:00:00 pm EDT to Your Division s GradeScope Site

HW-1: Due Tuesday 13 Jun 2017 by 2:00:00 pm EDT to Your Division s GradeScope Site HW-1: Due Tuesday 13 Jun 2017 by 2:00:00 pm EDT to A residential ceiling fan is shown in the photograph below. It consists of an electric motor, the fan blades, and the light. Sketch each of these three

More information

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad -500 043 MECHANICAL ENGINEERING ASSIGNMENT Course Name : THERMAL ENGINEERING II Course Code : A50518 Class : III B. Tech I Semester

More information

ASSIGNMENT 2 Coal and Ash Handling System and Draught Systems

ASSIGNMENT 2 Coal and Ash Handling System and Draught Systems ASSIGNMENT 1 Thermal Power Plant & High Pressure Boiler 1. State the factors to be considered for selection of site for thermal power plant 2. State desirable to control the super heat temperature. Explain

More information

Reading Problems , 11.36, 11.43, 11.47, 11.52, 11.55, 11.58, 11.74

Reading Problems , 11.36, 11.43, 11.47, 11.52, 11.55, 11.58, 11.74 Rankine Cycle Reading Problems 11.1 11.7 11.29, 11.36, 11.43, 11.47, 11.52, 11.55, 11.58, 11.74 Definitions working fluid is alternately vaporized and condensed as it recirculates in a closed cycle the

More information

OUTCOME 2 TUTORIAL 2 STEADY FLOW PLANT

OUTCOME 2 TUTORIAL 2 STEADY FLOW PLANT UNIT 47: Engineering Plant Technology Unit code: F/601/1433 QCF level: 5 Credit value: 15 OUTCOME 2 TUTORIAL 2 STEADY FLOW PLANT 2 Be able to apply the steady flow energy equation (SFEE) to plant and equipment

More information

HW-1: Due Friday 25 August 2017 by 4:30:00 pm EDT To Your Division s GradeScope Site

HW-1: Due Friday 25 August 2017 by 4:30:00 pm EDT To Your Division s GradeScope Site HW-1: Due Friday 25 August 2017 by 4:30:00 pm EDT To Your Division s GradeScope Site A washing machine agitator is shown below. Its purpose is to mix soiled clothing with the water-detergent mixture. Draw

More information

Chapter 10 Vapor and Combined Power Cycles

Chapter 10 Vapor and Combined Power Cycles Chapter 10 Vapor and Combined Power Cycles Dr. Mohammad Tarawneh Thermodynamics: An Engineering Approach, 5th edition by Yunus A. Çengel and Michael A. Boles We consider power cycles where the working

More information

Code No: R31034 R10 Set No: 1

Code No: R31034 R10 Set No: 1 Code No: R31034 R10 Set No: 1 JNT University Kakinada III B.Tech. I Semester Regular/Supplementary Examinations, Dec - 2014/Jan -2015 THERMAL ENGINEERING-II (Com. to Mechanical Engineering and Automobile

More information

FEE, CTU in Prague Power Engineering 2 (BE5B15EN2) Exercise 3

FEE, CTU in Prague Power Engineering 2 (BE5B15EN2) Exercise 3 Example 1: How is the applied heat for 1 kg of water steam at constant pressure p = 1.47 MPa, if the dryness of wet water is increased from x 1 = 0.8 to x 2 = 0.96? Dryness of wet steam the ratio of steam

More information

UNIVERSITY OF TORONTO FACULTY OF APPLIED SCIENCE AND ENGINEERING FINAL EXAMINATION, DECEMBER 2008 MIE 411H1 F - THERMAL ENERGY CONVERSION

UNIVERSITY OF TORONTO FACULTY OF APPLIED SCIENCE AND ENGINEERING FINAL EXAMINATION, DECEMBER 2008 MIE 411H1 F - THERMAL ENERGY CONVERSION UNIVERSITY OF TORONTO FACULTY OF APPLIED SCIENCE AND ENGINEERING FINAL EXAMINATION, DECEMBER 2008 MIE 411H1 F - THERMAL ENERGY CONVERSION Exam Type: X Examiner: J.S. Wallace You may use your copy of the

More information

Feedwater Heaters (FWH)

Feedwater Heaters (FWH) Feedwater Heaters (FWH) A practical Regeneration process in steam power plants is accomplished by extracting or bleeding, steam from the turbine at various points. This steam, which could have produced

More information

Lecture No.3. The Ideal Reheat Rankine Cycle

Lecture No.3. The Ideal Reheat Rankine Cycle Lecture No.3 The Ideal Reheat Rankine Cycle 3.1 Introduction We noted in the last section that increasing the boiler pressure increases the thermal efficiency of the Rankine cycle, but it also increases

More information

MCE535 Thermal Power and Propulsive Systems. Lecture 04: 04/10/2017

MCE535 Thermal Power and Propulsive Systems. Lecture 04: 04/10/2017 MCE535 Thermal Power and Propulsive Systems Lecture 04: 04/10/2017 Dr. Ayokunle O. Balogun (A212) balogun.ayokunle@lmu.edu.ng Class: Thursday (3 5 pm) Etiquettes and MOP Attendance is a requirement. There

More information

B.Tech. Civil (Construction Management) / B.Tech. Civil (Water Resources Engineering) B.Tech. (Aerospace Engineering) Term-End Examination

B.Tech. Civil (Construction Management) / B.Tech. Civil (Water Resources Engineering) B.Tech. (Aerospace Engineering) Term-End Examination No. of Printed Pages : 5 ET-201(B) B.Tech. Civil (Construction Management) / B.Tech. Civil (Water Resources Engineering) B.Tech. (Aerospace Engineering) Term-End Examination 007: 7 8 December, 2013 ET-201(B)

More information

Review Questions for the FE Examination

Review Questions for the FE Examination 110 THE FIRST LAW OF THERMODYNAMICS [CHAP. 4 4.1FE Review Questions for the FE Examination Select a correct statement of the first law if kinetic and potential energy changes are negligible. (A) Heat transfer

More information

CH 7: GAS-TURBINE ENGINES Prepared by Dr. Assim Al-Daraje BRAYTON CYCLE: THE IDEAL CYCLE FOR GAS-TURBINE ENGINES

CH 7: GAS-TURBINE ENGINES Prepared by Dr. Assim Al-Daraje BRAYTON CYCLE: THE IDEAL CYCLE FOR GAS-TURBINE ENGINES CH 7: GAS-TURBINE ENGINES Prepared by Dr. Assim Al-Daraje BRAYTON CYCLE: THE IDEAL CYCLE FOR GAS-TURBINE ENGINES The combustion process is replaced by a constant-pressure heat-addition process from an

More information

Chapter 10. In Chap. 9 we discussed gas power cycles for which the VAPOR AND COMBINED POWER CYCLES. Objectives

Chapter 10. In Chap. 9 we discussed gas power cycles for which the VAPOR AND COMBINED POWER CYCLES. Objectives Chapter 0 VAPOR AND COMBINED POWER CYCLES In Chap. 9 we discussed gas power cycles for which the working fluid remains a gas throughout the entire cycle. In this chapter, we consider vapor power cycles

More information

Eng Thermodynamics I: Sample Final Exam Questions 1

Eng Thermodynamics I: Sample Final Exam Questions 1 Eng3901 - Thermodynamics I: Sample Final Exam Questions 1 The final exam in Eng3901 - Thermodynamics I consists of four questions: (1) 1st Law analysis of a steam power cycle, or a vapour compression refrigeration

More information

Chapter 10. In Chap. 9 we discussed gas power cycles for which the VAPOR AND COMBINED POWER CYCLES. Objectives

Chapter 10. In Chap. 9 we discussed gas power cycles for which the VAPOR AND COMBINED POWER CYCLES. Objectives Chapter 0 VAPOR AND COMBINED POWER CYCLES In Chap. 9 we discussed gas power cycles for which the working fluid remains a gas throughout the entire cycle. In this chapter, we consider vapor power cycles

More information

LECTURE-14. Air Refrigeration Cycles. Coefficient of Performance of a Refrigerator:

LECTURE-14. Air Refrigeration Cycles. Coefficient of Performance of a Refrigerator: Lecturer: -Dr. Esam Mejbil Abid Subject: Air Conditioning and Refrigeration Year: Fourth B.Sc. Babylon University College of Engineering Department of Mechanical Engineering LECTURE-14 Air Refrigeration

More information

Chapter 10 VAPOR AND COMBINED POWER CYCLES

Chapter 10 VAPOR AND COMBINED POWER CYCLES Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 10 VAPOR AND COMBINED POWER CYCLES Copyright The McGraw-Hill Companies, Inc. Permission

More information

Consider a simple ideal Rankine cycle with fixed turbine inlet conditions. What is the effect of lowering the condenser pressure on

Consider a simple ideal Rankine cycle with fixed turbine inlet conditions. What is the effect of lowering the condenser pressure on Chapter 10, Problem 8C. Consider a simple ideal Rankine cycle with fixed turbine inlet conditions. What is the effect of lowering the condenser pressure on Pump work input: Turbine work output: Heat supplied:

More information

Thermodynamics: Homework A Set 6 Jennifer West (2004)

Thermodynamics: Homework A Set 6 Jennifer West (2004) Thermodynamics: Homework A Set 6 Jennifer West (2004) Problem 1 Consider the process shown. The steam line conditions at piont 1 are 2 MPa, 400 C. The pressure at point 2 is 1.5 MPa. The turbine exhaust

More information

flow work, p. 173 energy rate balance, p. 174 nozzle, p. 177 diffuser, p. 177 turbine, p. 180 compressor, p. 184 (4.4b) p. 166

flow work, p. 173 energy rate balance, p. 174 nozzle, p. 177 diffuser, p. 177 turbine, p. 180 compressor, p. 184 (4.4b) p. 166 0 Chapter 4 Control Volume Analysis Using Energy The use of mass and energy balances for control volumes at steady state is illustrated for nozzles and diffusers, turbines, compressors and pumps, heat

More information

UNIT NO-03 [8 hrs] Second Law Of Thermodynamics: Introduction (Law of degradation of energy), Thermal energy reservoirs, Kelvin-Plank & Clausius

UNIT NO-03 [8 hrs] Second Law Of Thermodynamics: Introduction (Law of degradation of energy), Thermal energy reservoirs, Kelvin-Plank & Clausius UNIT NO-03 [8 hrs] Second Law Of Thermodynamics: Introduction (Law of degradation of energy), Thermal energy reservoirs, Kelvin-Plank & Clausius statements, Heat engines, Refrigerator and Heat pump, Perpetual

More information

CHAPTER 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES

CHAPTER 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Thermodynamics: An Engineering Approach 8th Edition in SI Units Yunus A. Ç engel, Michael A. Boles McGraw-Hill, 2015 CHAPTER 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Objectives Develop the conservation

More information

ESO 201A Thermodynamics

ESO 201A Thermodynamics ESO 201A Thermodynamics Instructor: Sameer Khandekar Tutorial 10 [8-23] A house that is losing heat at a rate of 50,000 kj/h when the outside temperature drops to 4 C is to be heated byelectric resistance

More information

Chapter 5: Thermodynamic Processes and Cycles

Chapter 5: Thermodynamic Processes and Cycles Chapter 5: Thermodynamic Processes and Cycles 5-6) This problem examines the Rankine heat engine introduced in Figure 5-5. Saturated steam at T = 250 C enters the turbine and the condenser operates at

More information

St.MARTIN S ENGINEERING COLLEGE Dhulapally,Secunderabad,

St.MARTIN S ENGINEERING COLLEGE Dhulapally,Secunderabad, St.MARTIN S ENGINEERING COLLEGE Dhulapally,Secunderabad, 500014. MECHANICAL ENGINEERING TUTORIAL QUESTION BANK Course Name : THERMAL ENGINEERING II Course Code : A50326- Class : III B. Tech I Semester

More information

Air Cycle Refrigeration Systems Nagendra M CBM Engineer, Hindusthan Zink.Ltd The specific objectives of the lesson This lesson discusses various gas cycle refrigeration systems based on air, namely: 1.

More information

R13. (12M) efficiency.

R13. (12M) efficiency. SET - 1 II B. Tech I Semester Regular/Supplementary Examinations, Oct/Nov - 2016 THERMAL AND HYDRO PRIME MOVERS (Electrical and Electronics Engineering) Time: 3 hours Max. Marks: 70 Note: 1. Question Paper

More information

In this lecture... Solve problems related to First law of thermodynamics for closed and open systems Heat engines Refrigerators and heat pumps

In this lecture... Solve problems related to First law of thermodynamics for closed and open systems Heat engines Refrigerators and heat pumps 13 1 In this lecture... Solve problems related to First law of thermodynamics for closed and open systems Heat engines Refrigerators and heat pumps 2 Problem 1 A 50 kg iron block at 80 C is dropped into

More information

Chapter 6. The Second Law of Thermodynamics. by Asst. Prof. Dr.Woranee Paengjuntuek and Asst. Prof. Dr.Worarattana Pattaraprakorn

Chapter 6. The Second Law of Thermodynamics. by Asst. Prof. Dr.Woranee Paengjuntuek and Asst. Prof. Dr.Worarattana Pattaraprakorn Chapter 6 The Second Law of Thermodynamics by Asst. Prof. Dr.Woranee Paengjuntuek and Asst. Prof. Dr.Worarattana Pattaraprakorn Reference: Cengel, Yunus A. and Michael A. Boles, Thermodynamics: An Engineering

More information

2 nd Law of Thermodynamics

2 nd Law of Thermodynamics 2 nd aw of Thermodynamics 2 nd aw of Thermodynamics 1 st law 2 nd law A process must satisfy both the first and the second laws of thermodynamics to proceed 1 st law : is concerned with the conversion

More information

LECTURE-15. Ideal Reverse Brayton Cycle. Figure (6) Schematic of a closed reverse Brayton cycle

LECTURE-15. Ideal Reverse Brayton Cycle. Figure (6) Schematic of a closed reverse Brayton cycle Lecturer: -Dr. Esam Mejbil Abid Subject: Air Conditioning and Refrigeration Year: Fourth B.Sc. Babylon University College of Engineering Department of Mechanical Engineering LECTURE-15 Ideal Reverse Brayton

More information

MCG THERMODYNAMICS II. 22 April 2008 Page 1 of 7 Prof. W. Hallett

MCG THERMODYNAMICS II. 22 April 2008 Page 1 of 7 Prof. W. Hallett Faculté de génie Génie mécanique Faculty of Engineering Mechanical Engineering MCG2131 - THERMODYNAMICS II 22 April 2008 Page 1 of 7 Prof. W. Hallett Closed book. Non-programmable calculators only allowed.

More information

water is typically used as the working fluid because of its low cost and relatively large value of enthalpy of vaporization

water is typically used as the working fluid because of its low cost and relatively large value of enthalpy of vaporization Rankine Cycle Reading Problems 10-2 10-7 10-16, 10-34, 10-37, 10-44, 10-47, 10-59 Definitions working fluid is alternately vaporized and condensed as it recirculates in a closed cycle water is typically

More information

wb Thermodynamics 2 Lecture 10 Energy Conversion Systems

wb Thermodynamics 2 Lecture 10 Energy Conversion Systems wb1224 - Thermodynamics 2 Lecture 10 Energy Conversion Systems Piero Colonna, Lecturer Prepared with the help of Teus van der Stelt 13-12-2010 Delft University of Technology Challenge the future Content

More information

Chapter 6 THE SECOND LAW OF THERMODYNAMICS

Chapter 6 THE SECOND LAW OF THERMODYNAMICS Chapter 6 THE SECOND LAW OF THERMODYNAMICS INTRODUCTION TO THE SECOND LAW A cup of hot coffee does not get hotter in a cooler room. Transferring heat to a paddle wheel will not cause it to rotate. Transferring

More information

T.E. (Mech., Mech. S/W) (Semester II) Examination, 2011 TURBOMACHINES (New) (2008 Pattern)

T.E. (Mech., Mech. S/W) (Semester II) Examination, 2011 TURBOMACHINES (New) (2008 Pattern) *4063218* [4063] 218 T.E. (Mech., Mech. S/W) (Semester II) Examination, 2011 TURBOMACHINES (New) (2008 Pattern) Time : 3 Hours Marks : 100 Instructions : 1) Answer any three questions from each Section.

More information

EFFECT OF AMBIENT TEMPERATURE, GAS TURBINE INLET TEMPERATURE AND COMPRESSOR PRESSURE RATIO ON PERFORMANCE OF COMBINED CYCLE POWER PLANT

EFFECT OF AMBIENT TEMPERATURE, GAS TURBINE INLET TEMPERATURE AND COMPRESSOR PRESSURE RATIO ON PERFORMANCE OF COMBINED CYCLE POWER PLANT EFFECT OF AMBIENT TEMPERATURE, GAS TURBINE INLET TEMPERATURE AND COMPRESSOR PRESSURE RATIO ON PERFORMANCE OF COMBINED CYCLE POWER PLANT Harendra Singh 1, Prashant Kumar Tayal 2 NeeruGoyal 3, Pankaj Mohan

More information

SUMMER 13 EXAMINATION

SUMMER 13 EXAMINATION Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. 2) The model answer and the answer written by candidate

More information

Chapter 6: Stationary Combustion Systems

Chapter 6: Stationary Combustion Systems Chapter 6: Stationary Combustion Systems Figure 6-1. Schematic of components of coal-fired electric plant, with conversion of coal to electricity via boiler, turbine, and generator US Energy Sources 2004

More information

Stationary Combustion Systems Chapter 6

Stationary Combustion Systems Chapter 6 Stationary Combustion Systems Chapter 6 Stationary combustion systems presently supply most of the earth s electricity. Conversion will take time, so study of these systems in order to improve them is

More information

[4163] T.E. (Mechanical) TURBO MACHINES (2008 Pattern) (Common to Mech. S/W) (Sem. - II)

[4163] T.E. (Mechanical) TURBO MACHINES (2008 Pattern) (Common to Mech. S/W) (Sem. - II) Total No. of Questions : 12] P1061 SEAT No. : [Total No. of Pages : 7 [4163] - 218 T.E. (Mechanical) TURBO MACHINES (2008 Pattern) (Common to Mech. S/W) (Sem. - II) Time : 3 Hours] [Max. Marks :100 Instructions

More information

Design Features of Combined Cycle Systems

Design Features of Combined Cycle Systems Design Features of Combined Cycle Systems 1.0 Introduction As we have discussed in class, one of the largest irreversibilities associated with simple gas turbine cycles is the high temperature exhaust.

More information

Chapter 8. Vapor Power Systems

Chapter 8. Vapor Power Systems Chapter 8 Vapor Power Systems Introducing Power Generation To meet our national power needs there are challenges related to Declining economically recoverable supplies of nonrenewable energy resources.

More information

THE SECOND LAW OF THERMODYNAMICS

THE SECOND LAW OF THERMODYNAMICS Fundamentals of Thermal-Fluid Sciences, 3rd Edition Yunus A. Cengel, Robert H. Turner, John M. Cimbala McGraw-Hill, 2008 THE SECOND LAW OF THERMODYNAMICS Mehmet Kanoglu Copyright The McGraw-Hill Companies,

More information

Thermodynamic Analysis on Gas Turbine Unit

Thermodynamic Analysis on Gas Turbine Unit Gas Turbine Exhaust Super Heater Economiser HRB Exhaust IJIRST International Journal for Innovative Research in Science & Technology Volume 2 Issue 02 July 2015 ISSN (online): 2349-6010 Thermodynamic Analysis

More information

Applied Thermo Fluids-II: (Autumn 2017) Section-A: Thermal Power Plants

Applied Thermo Fluids-II: (Autumn 2017) Section-A: Thermal Power Plants Applied Thermo Fluids-II: (Autumn 2017) Section-A: Thermal Power Plants Module-1 (Introduction & Thermodynamics of thermal power plants) Dr. M. Ramgopal, Mechanical Engineering, IIT Kharagpur Reference:

More information

MECHANICAL ENGINEERING THERMAL AND FLUID SYSTEMS STUDY PROBLEMS

MECHANICAL ENGINEERING THERMAL AND FLUID SYSTEMS STUDY PROBLEMS MECHANICAL ENGINEERING THERMAL AND FLUID SYSTEMS STUDY PROBLEMS PRINCIPLES: THERMODYNAMICS & ENERGY BALANCES 1 Copyright 2018. All rights reserved. How to use this book The exam specifications in effect

More information

Introduction to Aerospace Propulsion. Prof. Bhaskar Roy. Prof. A. M. Pradeep. Department of Aerospace Engineering

Introduction to Aerospace Propulsion. Prof. Bhaskar Roy. Prof. A. M. Pradeep. Department of Aerospace Engineering Introduction to Aerospace Propulsion Prof. Bhaskar Roy Prof. A. M. Pradeep Department of Aerospace Engineering Indian Institute of technology, Bombay Module No. # 01 Lecture No. # 18 Rankine cycle, Brayton

More information

Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES

Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Thermodynamics: An Engineering Approach Seventh Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Copyright The McGraw-Hill Companies, Inc.

More information

Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES

Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Thermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Copyright The McGraw-Hill Companies,

More information

semester + ME6404 THERMAL ENGINEERING UNIT III NOZZLES, TURBINES & STEAM POWER CYCLES UNIT-III

semester + ME6404 THERMAL ENGINEERING UNIT III NOZZLES, TURBINES & STEAM POWER CYCLES UNIT-III ME6404 THERMAL ENGINEERING UNIT III NOZZLES, TURBINES & STEAM POWER CYCLES UNIT-III 3. 1 CONTENTS 3.1 Flow of steam through nozzles: 3.2 Continuity and steady flow energy equations 3.3 Types of Nozzles

More information

Chapter 5 THE SECOND LAW OF THERMODYNAMICS

Chapter 5 THE SECOND LAW OF THERMODYNAMICS The Second aw of Thermodynamics Chapter 5 TE SECOND AW OF TEMODYNAMICS The Second aw of Thermodynamics and Thermal Energy eservoirs 5-C Water is not a fuel; thus the claim is false. 5-2C Transferring 5

More information

Thermodynamics. Unit level 5 Credit value 15. Introduction. Learning Outcomes

Thermodynamics. Unit level 5 Credit value 15. Introduction. Learning Outcomes Unit 38: Unit code Further Thermodynamics D/615/1506 Unit level 5 Credit value 15 Introduction From the refrigerators that we use in our homes to the colossal power stations that generate the electricity

More information

S.Y. Diploma : Sem. III [PG/PT/ME] Thermal Engineering

S.Y. Diploma : Sem. III [PG/PT/ME] Thermal Engineering S.Y. Diploma : Sem. III [PG/PT/ME] Thermal Engineering Time: 3 Hrs. Prelim Question Paper Solution [Marks : 70 Q.1 Attempt any FIVE of the following. [10] Q.1(a) Explain difference between Thermodynamic

More information

Contents. Tribute to a great thermodynamicist Professor Lucien Borel

Contents. Tribute to a great thermodynamicist Professor Lucien Borel Contents Preface Tribute to a great thermodynamicist Professor Lucien Borel v vii CHAPTER 1 Generalities and fundamental laws 1 l.a Cooling of a copper piece 1 l.b Shock of a container against a wall 3

More information

Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES

Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Thermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Mehmet Kanoglu University of

More information

Combined Heat and Power

Combined Heat and Power Lecture 12 Combined Heat and Power Combustion Turbines and Co-generation Combustion Turbines and Combined Heat and Power (CHP) Systems See B. K. Hodge, Chapter 5 and Chapter 11. ISBN: 978-0-470-14250-9

More information

CONTROL VOLUME ANALYSIS USING ENERGY. By Ertanto Vetra

CONTROL VOLUME ANALYSIS USING ENERGY. By Ertanto Vetra CONTROL VOLUME ANALYSIS USING ENERGY 1 By Ertanto Vetra Outlines Mass Balance Energy Balance Steady State and Transient Analysis Applications 2 Conservation of mass Conservation of mass is one of the most

More information

CHAPTER 2 POWER PLANT THERMODYNAMICS

CHAPTER 2 POWER PLANT THERMODYNAMICS CHAPTER 2 POWER PLANT THERMODYNAMICS 2.1. Thermodynamic Prciples... 2 2.2. Steady Flow Engeerg Devices and Processes... 4 2.3. Heat Enge and Cycles... 8 2.4. Carnot Cycle... 10 2.5. Ranke Cycle... 10 Chapter

More information

Rankine cycle. Contents. Description

Rankine cycle. Contents. Description Page 1 of 7 Rankine cycle From Wikipedia, the free encyclopedia The Rankine cycle is a model that is used to predict the performance of steam turbine systems. The Rankine cycle is an idealized thermodynamic

More information

Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008

Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES SUMMARY 1 CONSERVATION OF MASS Conservation

More information

ME 331 Thermodynamics II

ME 331 Thermodynamics II ME 331 Thermodynamics II Prerequisite: ME 230 Thermodynamics I Instructor: Chainarong Chaktranond (Dept. of Mechanical Engineering) Lecture: Tue (9.30-11.00) and Wed (13.30 15.00) E-mail: cchainar@engr.tu.ac.th

More information