Feedwater Flow Measurement with Venturi and Comparison to the other Parameters in NPP Krško

Size: px
Start display at page:

Download "Feedwater Flow Measurement with Venturi and Comparison to the other Parameters in NPP Krško"

Transcription

1 Feedwater Flow Measurement with Venturi and Comparison to the other Parameters in NPP Krško ABSTRACT Vinko Planinc, Aljoša Šumlaj, Robert Rostohar, Dejvi Kadivnik Nuclear Power Plant Krško Vrbina 12, SI-8270 Krško, Slovenia Feedwater flow is one of the inputs to the secondary calorimetric calculation to determine the reactor thermal power in a nuclear power plant. Measurement of the mass flow is normally performed with one venturi nozzle per loop. The basic principle is to measure pressure difference between the nozzle inlet and the throat. The venturi nozzle is sensitive to the fouling which is changing throughout the fuel cycle and from cycle to cycle. These changes can be noticed by comparing different parameters which are correlated to the reactor thermal power. The main contributor is fouling which can occur inside of the flow elements and can give incorrect measurements. For a nuclear power plant it is important to precisely measure the feedwater mass flow, due to the fact that it is in direct correlation to the thermal output of the primary side. Every deviation of the mass flow measurement also means deviation of the output of the main electrical generator. The design uncertainty of the feedwater mass flow measurement is 2% and this error is also incorporated into the safety analyses. To confirm the appearance of the fouling on venturi, the flow can be independently measured. Among all the options the ultrasonic measurement and validation of parameters are most widely used in nuclear power plants. This paper also sheds light on some short-term and long-term actions which will confirm fouling and eliminate drift in feedwater flow measurement. 1 INTRODUCTION After comparing some of the key parameters to the previous cycle values Krško NPP has noticed that the actual feedwater flow could be lower than indicated in the last fuel cycle. Following the modernization and uprate in 2000, Krško NPP made some investment in reliability and efficiency of the secondary cycle. The new Low-Pressure Turbines and High- Pressure Feedwater heaters were installed during the outage 2006 and the Plant performance test was performed; its results showed an increment in the generator gross output of 20 MWe. The next improvement was the replacement of Moisture Separator Reheaters in 2007 which resulted in better efficiency of moisture removal, lower pressure drop and higher temperature of reheat steam. The generator output was expected to increase by at least 4 MWe. When the plant reached full power and stabilization it was noticed that some of the key parameters, which are related to the thermal power of the reactor, were lower than during the

2 previous cycle. A detailed analysis was performed to find the cause for discrepancy in thermal power. Different parameters were compared with the previous data. 2 BACKGROUND Reactor thermal power (RTP) is directly proportional to the feedwater flow (feedwater mass flow) for pressurized water reactors (PWR s) as defined by the following equation: Reactor Thermal Power = qm (hs hfw) + (heat gain/loss) [W] (1) where: qm = feedwater mass flow [kg/s] hs = steam enthalpy, dependent on temperature, pressure, and moisture [J/kg] hfw = feed enthalpy, dependent on temperature and pressure [J/kg] heat gain/loss = from reactor-attached piping and pumps [W] The key parameter in Eq. (1) is feedwater mass flow which is also the main contributor to the total uncertainty of computations of reactor thermal power in a PWR plant. Basic principle of calorimetric measurement is shown in Figure 1 [1]. Figure 1: Principle of calorimetric measurement 2.1 Measurement principle of feedwater flow The calorimetric measurement on the secondarz side is used to determine the reactor thermal power. Pressure and temperature can be precisely measured and the enthalpy can be calculated from those measurements. The measurement of fluid mass flow in a feedwater line is more complex. The technology in common use for measuring feedwater flow in nuclear plants can be divided into two categories: methods based on the measurement of differential pressure created by an inserted device (orifice plate, venturi, or nozzle) and methods based on the measurement of high frequency sound waves (ultrasonic technology) [2].

3 Differential pressure measurement Differential pressure (DP) technology has been the industry standard for feedwater flow measurement throughout the development of the nuclear power industry. These instruments calculate mass flow from the measurement of differential pressure across the flow constriction and from the static pressure and temperature of a flowing fluid. Types of differential pressure flow elements include venturies, flow nozzles, and orifices. Each of these elements is based on the same operating principle; however, they differ in the geometry of the flow restriction, the extent of irreversible pressure loss, and code acceptance. Figure 2: Differential pressure measurement by VENTURI nozzle DP flow meters reduce the flow cross-sectional area, resulting in an increase in fluid velocity through the throat of the flow element. The increased velocity causes a measurable difference in pressure between locations upstream and downstream of the flow element. The difference between the pressure upstream of the contraction and the pressure downstream of the contraction is measured with taps bored into the pipe or the flow element. These taps can be located at several locations, determined by the particular style and method of determining flow. In a nozzle, the low-pressure (downstream) can be measured at the throat or downstream of the throat, again determined by the style of device (for example, throat tap or wall tap). The flow meter measures the differential pressure produced, and then flow is calculated using Eq. (2), which is derived from the Bernoulli equation. 2 π d q m = C E ε 2 Δp ρ 4 (2) where: q m = mass flow [kg/s] C = discharge coefficient [/] 1 E = = velocity of approach factor 4 (1 β ) d = diameter of flow restrictor [m] D = pipe inside diameter [m] ε = expansion factor [/] Δp = differential pressure [Pa] ρ = fluid density [kg/m 3 ] β = d/d = beta ratio[/]

4 As documented in the EPRI Nuclear Feedwater Flow Measurement Application Guide [2], the main errors related to differential pressure flow measurement can be grouped into the following categories: density errors, errors in differential pressure measurement, errors due to the plant computer, Errors due to impulse line condition, Errors due to thermal expansion, errors in the discharge coefficient and errors due to changes of the internal conditions. Changes of the internal conditions of a differential pressure flow meter affect the accuracy of the feedwater flow calculation. Erosion, corrosion, corrosion product buildup, and cleaning can alter the internal condition of the meter. Deposition of corrosion products in front of the throat, in the throat section, and in the recovery cone of the throat tap flow meter can increase the pressure drop across the meter. This maz cause an erroneously high mass flow indication Ultrasonic cross flow measurement An ultrasonic transit time flow meter measures the time necessary for an ultrasonic pulse to travel across the pipe from one transducer to another along the path that is diagonal to the fluid flow. The difference in times of flight for pulses traveling with and against the fluid flow is proportional to the fluid velocity. Figure 3: Ultrasonic measurement - Cross flow principle M = ρ PF A V (3) ax Where: M = mass flow [kg/s] ρ = density [kg/m 3 ] PF = velocity profile factor [/] A = area of cross section [m 2 ] V ax = average axial velocity [m/s] Technical errors potentially affecting ultrasonic flow measurement include the following: dimensional errors, density errors, timing errors, profile factor errors (experimental uncertainty, piping configuration, pipe roughness etc.), miscellaneous errors including sensitivity to the transducer equipment [2]. A typical uncertainty of cross flow measurement is less than 0.7%. The uncertainty calculated using actual pipe dimensions and observed variations is as low as 0.5% per pipe [2].

5 Parameters related to the thermal power Some of the parameters in nuclear power plant are directly or indirectly related to the reactor thermal power. These important parameters are listed in Table 1. Comparison of parameters between the current and previous fuel cycle can show if there is any change in feedwater flow measurement behavior. As an example, cold leg temperatures of reactor coolant are presented in Figure 4. Table 1: Important parameters related to the thermal power Parameter Feedwater flow 1 st stage impulse pressure Core temperature difference Reactor coolant temperatures Steam flow Opening of turbine control valves Final feedwater temperature Steam generator pressure Generator electrical output Moisture Separator Reheater outlet pressure Relation - Description Measured with venturi meter, used for calorimetric calculation Turbine power indication, used for determining referenced average temperature Measured in the primary legs. Linearly proportional to the thermal reactor power. Hot legs, Cold legs and Average reactor coolant temperature are used for reactor protection. Measured on the SG s outlet, independed of feedwater flow measurement Position of control valves, defines the steam flow, with respect to the SG pressure Measured with thermo element, used to calculate density and enthalpy. Increased temperature means higher power. Used to calculate steam enthalpy. Increased pressure of main steam means lower power. Electrical output corrected to the design vacuum. Increased outlet pressure means higher thermal power. Figure 4: Measured cold leg temperature of reactor coolant

6 Some of the parameters are not affected by the fouling in the venturi flow element. One of such parameters is the turbine impulse pressure, which is proportional to the turbine power and can be correlated with the steam flow. New terms can be defined as Ratio of Steam Flow (RSF) and Relative Ratio of Steam Flow (RRSF). RSF = Main steam flow/turbine impulse pressure (4) RRSF = RSF actual /RSF baseline (5) Where: Main steam flow = difference between the feedwater and blowdown flow [kg/s] Turbine impulse pressure = 1 st stage impulse pressure [Pa] RSF actual = actual ratio of steam flow RSF baseline = baseline ratio of steam flow (obtained from Plant performance test after Low-Pressure Turbine replacement) For monitoring purposes the easiest way is to monitor the trend of the relative ratio of RSF, as presented in Figure 5. 1,02 Relative ratio of steam flow 1,01 RRSF SG1 & SG2 (/) 1 0,99 GC20 GC21 GC22 GC23 RRPSG1 RRPSG2 0, Implementation of modification Figure 5: Relative Ratio of Steam Flow over the time In the past Krško NPP has implemented some changes which have positive effect on the secondary side efficiency. After the modernization and uprate in 2000, Krško NPP invested in reliability and efficiency of the secondary cycle. The new Low-Pressure Turbines and High- Pressure Feedwater heaters were installed during outage 2006 and Plant performance test was performed. The results have shown increment in Generator Gross Output of 20 MWe [3]. The next improvement took place in 2007 with Moisture Separator Reheaters (MSR) replacement, with better efficiency of moisture removal, lower pressure drop and higher temperature of reheat steam. The replacement of Low-Pressure Heaters in the condenser neck has minor influence on the efficiency.

7 After the replacement of Moisture Separator Reheaters, a performance test in accordance with ASME PTC 12.4 [4] (Power Test Code for Moisture Separator Reheater) was carried out. Pressure drop and outlet steam temperature have reached guaranteed values and the consumption of steam for reheat was bellow the design value, which means that more steam is available for turbine work. Outlet pressure of the superheated steam is lower than before the replacement and this can only be linked to the lower steam flow and consequently lower feedwater flow and therefore lower thermal power. Before the replacement, the generator electrical output increase of at least 4 MWe was anticipated. In accordance with ASME PTC 12.1 [5] (Power Test Code for Feedwater Heaters), a performance test was carried out. The result showed that the heaters were operating as designed and there were no significant changes to other parameters. All the modifications were reviewed and there is no negative effect on the generator electrical gross output. The net consumption was found to be increased by 0.15MW. 2.4 Determination of fouling thickness Feedwater flow in Krško NPP is measured with venturi flow element on the principle of pressure drop as described in section 2.1. In case there are some deposits in the venturi the pressure drop will be higher and consequently the indicated feedwater flow will be higher than actual. A simple calculation was used to determine the necessary thickness for 0.5% error on measured feedwater mass flow. qmd2 qmd 1 Δqm = 100% (6) qm D1 Δqm represents the difference in flow due to fouling (qm D2 ) compared to flow with no fouling (qm D1 ); expressed in % Using Eq. (2) with assumption that δ<<d we can obtain: 2 4 d 2δ 1 β Δqm = [%] (7) 4 d d 2δ 1 2 D δ Where: d...inside diameter of venturi = 207,2386 mm D...pipe diameter = 363,5756 mm δ...scaling thickness β...beta ratio = d/d = 0,57 All other parameters are assumed to be constant for scaling thickness (δ)<<d

8 δ Scaling thickness Figure 6: Krško venturi flow element [6] Results from Eq. (7) are presented in Figure 7. Feedwater flow decrease due to scaling buildup 1,20 Δqm Change in feedwater flow (%) 1,00 0,80 0,60 0,40 0,20 0,00 0 0,05 0,1 0,15 0,2 0,25 0,3 0,35 0,4 0,45 0,5 0,55 Scaling thickness (mm) Figure 7: Feedwater venturi scaling thickness versus measured feedwater flow error 3 FUTURE ACTIVITIES Evaluation of parameters after outage 2007 and their comparison with previous data shows that there are certain changes in feedwater flow measurement. A change to the feedwater flow measurement technique and the uncertainty may be considered as design change. According to 10 CFR 50, Appendix K, the plant safety systems should be designed by assuming that the reactor is generating 102% of its licensed power. Its 2% is intended to cover the uncertainty of measurements used in calorimetric calculations.

9 Short-term activities will focus on confirmation of venturi fouling. Three different actions are proposed: 1. Development of a procedure to confirm that all important parameters are within the expected range, showing that when plant operates at full power, the thermal power is close to the design value of 1994 MW. 2. Krško NPP plans to perform one-time measurement of feedwater flow with radioactive tracer. The uncertainty of this method is below 0.5% or even less [7]. 3. During the next outage venturi flow elements will be visually inspected. Long-term action: 1. Installation of permanent ultrasonic feedwater flow measurement. This will provide the basis for mini uprate up to 1.4%. The uprate is possible due to lower measurement uncertainty. This measurement can decrease uncertainty from 2% to the 0.5%. 2. Introducing Process Data Reconciliation according to VDI 2048 [8, 9] to decrease the feedwater flow measurement uncertainty. Uncertainty can be decreased to less than 0.5%. Some European nuclear power plants already implemented this method, e.g. Beznau [7]. 4 CONCLUSIONS Krško NPP implemented modifications and replaced some of the equipment on the secondary island to improve plant reliability and efficiency. The plant efficiency was increased after replacing the LP Turbines and HP Feedwater heaters in outage During outage 2007, two Moisture Separator Reheaters were replaced together with LP heaters in the condenser neck. It was expected that these changes would increase the generator output by at least 4 MW. However, after the plant stabilization at full power, the power output was not as high as expected. With the detailed analysis of several important plant aspects it can be concluded that fouling and scaling build-up inside venturies are the most likely reason for the missing MW s. Supporting this idea, there are certain parameters independent from fouling, which exhibit lower current values compared to the previous cycle data. Krško NPP plans to perform actions to confirm the fouling and to prevent such situation in the future. REFERENCES [1] Plant Support Engineering: Methods for Monitoring and Adjustment of Reactor Power Measurement Drift. EPRI, Palo Alto, CA: 2007, [2] Nuclear Feedwater Flow Measurement Application Guide: EPRI, Palo Alto, CA: 1999, TR [3] Thermal Kit New Low pressure Turbines T4-A6341, Rev. 9 [4] ASME PTC Power Test Code for Moisture Separator Reheater [5] ASME PTC Power Test Code for Feedwater Heater [6] Drawing " FEEDWATER FLOW ELEMENTS rev. 2

10 [7] T. Hungerbühler, M. Langenstein, Tracer test method and process data reconciliation based on VDI 2048 Comparison of two methods for highly accurate determination of feed water mass flow at NPP Beznau [8] Verein deutscher Ingenieure (VDI); Messung der Dampfnässe ; VDI 2043; 07/1999 [9] M. Langenstein, J. Jansky, Process Data Reconciliation in Nuclear Power Plants ; BTB- Jansky GmbH

Secondary Systems: Steam System

Secondary Systems: Steam System Secondary Systems: Steam System K.S. Rajan Professor, School of Chemical & Biotechnology SASTRA University Joint Initiative of IITs and IISc Funded by MHRD Page 1 of 10 Table of Contents 1 SECONDARY SYSTEM

More information

ASME PTC Flow Measurement

ASME PTC Flow Measurement ASME PTC 19.5-2004 Flow Measurement Performance Test Codes A N A M E R I C A N N A T I O N A L S T A N D A R D ASME PTC 19.5-2004 Flow Measurement Performance Test Codes AN AMERICAN NATIONAL STANDARD Three

More information

Utility Flow Metering for Steam and Heated/Chilled Water: A Tutorial. Richard Gruskos Flow Products Manager Kessler Ellis Products

Utility Flow Metering for Steam and Heated/Chilled Water: A Tutorial. Richard Gruskos Flow Products Manager Kessler Ellis Products Utility Flow Metering for Steam and Heated/Chilled Water: A Tutorial Richard Gruskos Flow Products Manager Kessler Ellis Products Review Flow Metering Principles: Flow Meters and Flow Computers Utility

More information

VENTURI FLOWMETERS. Your First Choice in Intelligent Flow Management...

VENTURI FLOWMETERS. Your First Choice in Intelligent Flow Management... VENTURI FLOWMETERS Your First Choice in Intelligent Flow Management... VENTURI FLOWMETERS Preso s complete line of Venturis offer reduced operating costs, proven accuracy, and great rangeability. Low permanent

More information

ORIFICE MTERE BASIC SELECTION & DESIGN CONSIDERATIONS. All rights reserved to thepetrostreet.com

ORIFICE MTERE BASIC SELECTION & DESIGN CONSIDERATIONS. All rights reserved to thepetrostreet.com ORIFICE MTERE BASIC SELECTION & DESIGN CONSIDERATIONS All rights reserved to thepetrostreet.com METER SELECTION PHILOSOPHY Reliability/ Repeatability Rangeability Versatility Economicsi Installation Cost

More information

Guidance page for practical work 15: modeling of the secondary circuit of a PWR

Guidance page for practical work 15: modeling of the secondary circuit of a PWR Guidance page for practical work 15: modeling of the secondary circuit of a PWR 1) Objectives of the practical work The aim is to investigate the potential of Thermoptim in modeling and calculation of

More information

NUCLEAR TRAINING CENTRE COURSE 134 FOR ONTARIO HYDRO USE ONLY

NUCLEAR TRAINING CENTRE COURSE 134 FOR ONTARIO HYDRO USE ONLY NUCLEAR TRAINING CENTRE COURSE 134 FOR ONTARIO HYDRO USE ONLY NUCLEAR TRAINING COURSE COURSE 134 1 - Level 3 - Equipment & System Principles 4 - TURBINE, GENERATOR & AUXILIARIES Index 134.00-0 Objectives

More information

ME ENGINEERING THERMODYNAMICS UNIT III QUESTION BANK SVCET

ME ENGINEERING THERMODYNAMICS UNIT III QUESTION BANK SVCET 1. A vessel of volume 0.04m 3 contains a mixture of saturated water and steam at a temperature of 250 0 C. The mass of the liquid present is 9 kg. Find the pressure, mass, specific volume, enthalpy, entropy

More information

February 5, 2013 Roy Ratcliffe, President RM Controls, Inc.

February 5, 2013 Roy Ratcliffe, President RM Controls, Inc. February 5, 2013 Roy Ratcliffe, President RM Controls, Inc. Volumetric Flow A velocity is a measure of the distance a particle of a substance moves in a given period of time The method of measurement used

More information

Network Analysis of Turbine and Feedwater Systems of the Fugen Nuclear Power Plant

Network Analysis of Turbine and Feedwater Systems of the Fugen Nuclear Power Plant Journal of Nuclear Science and Technology ISSN: 00-33 (Print) 88-48 (Online) Journal homepage: http://www.tandfonline.com/loi/tnst Network Analysis of Turbine and Feedwater Systems of the Fugen Nuclear

More information

Module 05 WWER/ VVER (Russian designed Pressurized Water Reactors)

Module 05 WWER/ VVER (Russian designed Pressurized Water Reactors) Module 05 WWER/ VVER (Russian designed Pressurized Water Reactors) 1.3.2016 Prof.Dr. Böck Technical University Vienna Atominstitut Stadionallee 2, 1020 Vienna, Austria ph: ++43-1-58801 141368 boeck@ati.ac.at

More information

Simulation of Fatigue relevant thermal Loads of Components in Piping Networks

Simulation of Fatigue relevant thermal Loads of Components in Piping Networks Simulation of Fatigue relevant thermal Loads of Components in Piping Networks Dr. Jan Leilich Dr. Gerhard Schlicht NSSS Primary Circuit and Ageing Management Dresden, Oct. 15 th, 2014 Thermal Loads in

More information

Feedwater Heaters (FWH)

Feedwater Heaters (FWH) Feedwater Heaters (FWH) A practical Regeneration process in steam power plants is accomplished by extracting or bleeding, steam from the turbine at various points. This steam, which could have produced

More information

Verification of the MELCOR Code Against SCDAP/RELAP5 for Severe Accident Analysis

Verification of the MELCOR Code Against SCDAP/RELAP5 for Severe Accident Analysis Verification of the Code Against SCDAP/RELAP5 for Severe Accident Analysis Jennifer Johnson COLBERT 1* and Karen VIEROW 2 1 School of Nuclear Engineering, Purdue University, West Lafayette, Indiana 47907-2017,

More information

Chapter 8. Vapor Power Systems

Chapter 8. Vapor Power Systems Chapter 8 Vapor Power Systems Introducing Power Generation To meet our national power needs there are challenges related to Declining economically recoverable supplies of nonrenewable energy resources.

More information

Ten Year Retrospective Look at HRSG FAC Assessment and Incidence. Peter S. Jackson, PhD, PE, David S. Moelling, PE, Mark Taylor, Mech. Eng.

Ten Year Retrospective Look at HRSG FAC Assessment and Incidence. Peter S. Jackson, PhD, PE, David S. Moelling, PE, Mark Taylor, Mech. Eng. Ten Year Retrospective Look at HRSG FAC Assessment and Incidence Peter S. Jackson, PhD, PE, David S. Moelling, PE, Mark Taylor, Mech. Eng. Ten years after we first reported at the 1999 EPRI Maintenance

More information

Downsizing a Claus Sulfur Recovery Unit

Downsizing a Claus Sulfur Recovery Unit INFRASTRUCTURE MINING & METALS NUCLEAR, SECURITY & ENVIRONMENTAL Downsizing a Claus Sulfur Recovery Unit OIL, GAS & CHEMICALS By Charles L. Kimtantas and Martin A. Taylor ckimtant@bechtel.com & mataylo1@bechtel.com

More information

Engineering Standard. Saudi Aramco DeskTop Standards

Engineering Standard. Saudi Aramco DeskTop Standards Engineering Standard 31 December, 2003 Instrumentation Standards Committee Members Al-Awami. L.H., Chairman Tuin, R.R., Vice Chairman Al-Dakhil, T.K. Al-Dhafeeri, F.T. Al-Khalifa, A.H. Al-Madhi, F.A. Alqaffas,

More information

Flow Test Data Book and Flow Handbook for 405 Compact Orifice Series and 1595 Conditioning Orifice Plate

Flow Test Data Book and Flow Handbook for 405 Compact Orifice Series and 1595 Conditioning Orifice Plate Test Book and Handbook for 405 Compact Orifice Series and 1595 Conditioning Orifice Plate Title Page 405 Compact Orifice Series and 1595 Conditioning Orifice Plate Test Book NOTICE Read this manual before

More information

Erosion Effects in Flowmeters

Erosion Effects in Flowmeters Subsea EXPO 2015 Conference, Aberdeen 11-12th February 2015 Erosion Effects in Flowmeters John Peters, NEL Tariq Boussouara, NEL Slide 1 Presentation Contents Project Objective Flowmeter Details, Test

More information

Nuclear Power A Journey of Continuous Improvement

Nuclear Power A Journey of Continuous Improvement Nuclear Power A Journey of Continuous Improvement Westinghouse Non Proprietary Class 3 Our Place in Nuclear History Innovation 1886 and forever Implementation & Improvement 1957 through Today Renaissance

More information

OUTCOME 2 TUTORIAL 2 STEADY FLOW PLANT

OUTCOME 2 TUTORIAL 2 STEADY FLOW PLANT UNIT 47: Engineering Plant Technology Unit code: F/601/1433 QCF level: 5 Credit value: 15 OUTCOME 2 TUTORIAL 2 STEADY FLOW PLANT 2 Be able to apply the steady flow energy equation (SFEE) to plant and equipment

More information

VENTURI FLOW METER CALIBRATIONS SERIAL NUMBERS: , , , Prepared for. Imperial Flange and Fitting.

VENTURI FLOW METER CALIBRATIONS SERIAL NUMBERS: , , , Prepared for. Imperial Flange and Fitting. VENTURI FLOW METER CALIBRATIONS SERIAL NUMBERS: 23034-1, 23034-2, 23034-3, 23034-4 Prepared for Imperial Flange and Fitting January 2007 UTAH WATER RESEARCH LABORATORY Utah State University Report No.

More information

AGEING MANAGEMENT ASSESSMENT

AGEING MANAGEMENT ASSESSMENT AGEING MANAGEMENT ASSESSMENT Module 9 Session 9 Resource document: AMAT Guidelines, Reference document for Ageing Management Assessment Teams, Services Series No. 4, (1999) International Atomic Energy

More information

Consider a simple ideal Rankine cycle with fixed turbine inlet conditions. What is the effect of lowering the condenser pressure on

Consider a simple ideal Rankine cycle with fixed turbine inlet conditions. What is the effect of lowering the condenser pressure on Chapter 10, Problem 8C. Consider a simple ideal Rankine cycle with fixed turbine inlet conditions. What is the effect of lowering the condenser pressure on Pump work input: Turbine work output: Heat supplied:

More information

GENERAL CONTENTS SECTION I - NUCLEAR ISLAND COMPONENTS

GENERAL CONTENTS SECTION I - NUCLEAR ISLAND COMPONENTS - June 2013 Addendum GENERAL CONTENTS SECTION I - NUCLEAR ISLAND COMPONENTS SUBSECTION "A" : GENERAL RULES SUBSECTION "B" : CLASS 1 COMPONENTS SUBSECTION "C" : CLASS 2 COMPONENTS SUBSECTION "D" : CLASS

More information

Flow Meter Calibration

Flow Meter Calibration fluid mechanics H4 A compact unit that compares and shows the accuracy, losses and use of fundamental flow meters Key Features Unique quick-change flow meter adaptors and pressure connections Four tube

More information

APlus-QMC LLC. Catalog 2017

APlus-QMC LLC. Catalog 2017 APlus-QMC LLC Catalog 2017 A+FLOWTEK Balanced Flow Meter NASA 2006 Invention of the Year NASA 2010 Award for Excellence in Technology Transfer NASA 2010 and 2011 Nominee for Space Technology Hall of Fame

More information

COOLING TOWER DESIGN FOR CENTRAL GENERATORS OF CUET, BANGLADESH. Mohammad Sharif Khan, Golam Mainuddin, Abu Sadat Mohammad Sayem, Nadeem Nafis

COOLING TOWER DESIGN FOR CENTRAL GENERATORS OF CUET, BANGLADESH. Mohammad Sharif Khan, Golam Mainuddin, Abu Sadat Mohammad Sayem, Nadeem Nafis Proceedings of the 4 th BSME-ASME International Conference on Thermal Engineering 7-9 December, 008, Dhaka, Bangladesh COOLING TOWER DESIGN FOR CENTRAL GENERATORS OF CUET, BANGLADESH. Mohammad Sharif Khan,

More information

Nuclear Service Valves

Nuclear Service Valves GE Energy Consolidated* Pressure Relief Valves Nuclear Service Valves Pressure relief solutions for the nuclear industry Safety Relief Valves Safety Valves Advanced Technology and Equipment Manufactured

More information

Conceptual Design of Nuclear CCHP Using Absorption Cycle

Conceptual Design of Nuclear CCHP Using Absorption Cycle Conceptual Design of Nuclear CCHP Using Absorption Cycle International Conference on Opportunities and Challenges for Water Cooled Reactors in the 21 st Century Vienna, Austria, October 27-30, 2009 Gyunyoung

More information

Thermodynamic Considerations for Large Steam Turbine Upgrades and Retrofits

Thermodynamic Considerations for Large Steam Turbine Upgrades and Retrofits POWER-GEN Asia 2011 Kuala-Lumpur, Malaysia September 27-29, 2011 Thermodynamic Considerations for Large Steam Turbine Upgrades and Retrofits Leonid Moroz, Kirill Grebennik 15 New England Executive Park,

More information

FLUXUS F601. Portable, quick and reliable. Clamp-on ultrasonic flow meter. Measure from outside what's flowing inside

FLUXUS F601. Portable, quick and reliable. Clamp-on ultrasonic flow meter. Measure from outside what's flowing inside Reliable flow measurement in less than 5 minutes. Wide application range. With long life marathon battery. Portable, quick and reliable FLUXUS F601 Clamp-on ultrasonic flow meter Accurate Flexible Quick

More information

High Energy Piping Inspection Program for Power Generation and Process Industries. For Regulatory Compliance, Safety, and System Longevity

High Energy Piping Inspection Program for Power Generation and Process Industries. For Regulatory Compliance, Safety, and System Longevity High Energy Piping Inspection Program for Power Generation and Process Industries For Regulatory Compliance, Safety, and System Longevity EAPC Industrial Services offers an inspection plan for assessment

More information

Setting The Standard

Setting The Standard www.iacpe.com Setting The Standard Page : 1 of 91 Rev. 01- IACPE No 19, Jalan Bilal Mahmood 80100 Johor Bahru Malaysia MATERIAL SELECTION CPE LEVEL II The International of is providing the introduction

More information

OPERATING EXPERIENCE REGARDING THERMAL FATIGUE OF UNISOLABLE PIPING CONNECTED TO PWR REACTOR COOLANT SYSTEMS

OPERATING EXPERIENCE REGARDING THERMAL FATIGUE OF UNISOLABLE PIPING CONNECTED TO PWR REACTOR COOLANT SYSTEMS OPERATING EXPERIENCE REGARDING THERMAL FATIGUE OF UNISOLABLE PIPING CONNECTED TO PWR REACTOR COOLANT SYSTEMS ABSTRACT Paul Hirschberg John Carey Arthur F. Deardorff EPRI Project Manager Structural Integrity

More information

5. Steam Turbine Performance

5. Steam Turbine Performance 5. Steam Turbine Performance h HP = 88-90% IP = 90-94% Fossil Reheat HP = 82% LP = 85% LP = 87% LP = 90-91% Saturation Line Nuclear Reheat Nuclear Non-Reheat s Steam Turbine 5. Performance 1 / 93 1 2 3

More information

Investigations Of Low Pressure Two-Phase Steam- Water Injector

Investigations Of Low Pressure Two-Phase Steam- Water Injector Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 206 Investigations Of Low Pressure Two-Phase Steam- Water Injector Roman Kwidzinski

More information

Rosemount 405 Compact Orifice Primary Element

Rosemount 405 Compact Orifice Primary Element Rosemount 405 Compact Orifice Primary Element SPECIFICATIONS Performance Discharge Coefficient Uncertainty TABLE 20. 405 Compact Orifice Primary Element Type 405C (Conditioning Compact) 405P (1)(2) (Standard

More information

CHAPTER 4 STEAM TURBINE and CYCLE HEAT BALANCE

CHAPTER 4 STEAM TURBINE and CYCLE HEAT BALANCE CHAPTER STEAM TURBINE and CYCLE HEAT BALANCE.1. Steam Turbine Principles... 2.2. Steam Turbine Analysis... 3.3. Arrangements of Steam Turbines..... Heat Balance... 6.. System Performance... 7 Chapter 1

More information

MECHANICAL ENGINEERING THERMAL AND FLUID SYSTEMS STUDY PROBLEMS

MECHANICAL ENGINEERING THERMAL AND FLUID SYSTEMS STUDY PROBLEMS MECHANICAL ENGINEERING THERMAL AND FLUID SYSTEMS STUDY PROBLEMS PRINCIPLES: THERMODYNAMICS & ENERGY BALANCES 1 Copyright 2018. All rights reserved. How to use this book The exam specifications in effect

More information

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM IV (ME-41, 42,43 & 44)] QUIZ TEST-1 (Session: )

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM IV (ME-41, 42,43 & 44)] QUIZ TEST-1 (Session: ) QUIZ TEST-1 Q.1. In a stage of an impulse turbine provided with a single row wheel, the mean diameter of the blade ring is 80cm and the speed of the rotation is 3000rpm. The steam issues from the nozzle

More information

Pneumatic control and on/off valves for thermoelectric plants

Pneumatic control and on/off valves for thermoelectric plants BASIC REQUIREMENTS FOR QUALIFYING SUPPLY AND CONTRACTING COMPANIES Equipment category : FMVA11 Pneumatic control and on/off valves for thermoelectric plants Technical characteristics Page 1 of 8 CONTENTS

More information

VERIS Accelabar. Superior Flow Measurement Accuracy

VERIS Accelabar. Superior Flow Measurement Accuracy VERIS Superior Flow Measurement Accuracy Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit for up-to-date information. ...A New Idea in Flow

More information

Concepts and Features of ATMEA1 TM as the latest 1100 MWe-class 3-Loop PWR Plant

Concepts and Features of ATMEA1 TM as the latest 1100 MWe-class 3-Loop PWR Plant 8 Concepts and Features of ATMEA1 TM as the latest 1100 MWe-class 3-Loop PWR Plant KOZO TABUCHI *1 MASAYUKI TAKEDA *2 KAZUO TANAKA *2 JUNICHI IMAIZUMI *2 TAKASHI KANAGAWA *3 ATMEA1 TM is a 3-loop 1100

More information

Like piezoresistive, piezoelectric,

Like piezoresistive, piezoelectric, Sensors & Transducers Measuring gas flow with MEMS sensors Having proven their worth for accelerometer applications, MEMS sensors are also tackling gas-flow measurement BY YONGYAO CAI Director of Engineering

More information

RELAP5/MOD3.2 INVESTIGATION OF A VVER-440 STEAM GENERATOR HEADER COVER LIFTING

RELAP5/MOD3.2 INVESTIGATION OF A VVER-440 STEAM GENERATOR HEADER COVER LIFTING Science and Technology Journal of BgNS, Vol. 8, 1, September 2003, ISSN 1310-8727 RELAP5/MOD3.2 INVESTIGATION OF A VVER-440 STEAM GENERATOR HEADER COVER LIFTING Pavlin P. Groudev, Rositsa V. Gencheva,

More information

Gilflo flowmeters. for steam, liquids and gases

Gilflo flowmeters. for steam, liquids and gases Gilflo flowmeters for steam, liquids and gases The Gilflo spring loaded variable area flowmeter... offers an unrivalled 1:1 turndown and can be used to meter most industrial fluids including steam and

More information

KEPCO KEPRI Kim eui hwan

KEPCO KEPRI Kim eui hwan 2015 KEPIC PERFORMANCE TEST SEMINAR New Start! Open Soft Speed AGAIN KEPCO! 2015. 9. 22 KEPCO KEPRI Kim eui hwan 1 2 3 test Steam turbine test 2/42 3/42 Thermal analysis of Power Plant Cycle Grasp of the

More information

Risks Associated with Shutdown in PWRs

Risks Associated with Shutdown in PWRs International Conference Nuclear Option in Countries with Small and Mi Opatija, Croatia, 1996 Risks Associated with Shutdown in PWRs Igor Grlicarev Slovenian Nuclear Safety Administration Vojkova 59, 1113

More information

EFFECT OF AMBIENT TEMPERATURE, GAS TURBINE INLET TEMPERATURE AND COMPRESSOR PRESSURE RATIO ON PERFORMANCE OF COMBINED CYCLE POWER PLANT

EFFECT OF AMBIENT TEMPERATURE, GAS TURBINE INLET TEMPERATURE AND COMPRESSOR PRESSURE RATIO ON PERFORMANCE OF COMBINED CYCLE POWER PLANT EFFECT OF AMBIENT TEMPERATURE, GAS TURBINE INLET TEMPERATURE AND COMPRESSOR PRESSURE RATIO ON PERFORMANCE OF COMBINED CYCLE POWER PLANT Harendra Singh 1, Prashant Kumar Tayal 2 NeeruGoyal 3, Pankaj Mohan

More information

Newman Station Units 1, 2, and 4 Condition Assessment Report. El Paso Electric, Inc. El Paso, TX

Newman Station Units 1, 2, and 4 Condition Assessment Report. El Paso Electric, Inc. El Paso, TX Newman Station Units 1, 2, and 4 Condition Assessment Report prepared for El Paso Electric, Inc. El Paso, TX April 2010 Project No. 53549 prepared by Burns & McDonnell Engineering Company, Inc. COPYRIGHT

More information

Multi-Variable Optimisation Of Wet Vapour Organic Rankine Cycles With Twin-Screw Expanders

Multi-Variable Optimisation Of Wet Vapour Organic Rankine Cycles With Twin-Screw Expanders Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2014 Multi-Variable Optimisation Of Wet Vapour Organic Rankine Cycles With Twin-Screw Expanders

More information

Custom Engineered Flow Meters. Differential Pressure Products

Custom Engineered Flow Meters. Differential Pressure Products Custom Engineered Flow Meters Differential Pressure Products Ellipse Pitot Tube The Ellipse annular flow device is a primary flow meter designed to produce a differential pressure that is proportional

More information

a. The power required to drive the compressor; b. The inlet and output pipe cross-sectional area. [Ans: kw, m 2 ] [3.34, R. K.

a. The power required to drive the compressor; b. The inlet and output pipe cross-sectional area. [Ans: kw, m 2 ] [3.34, R. K. CHAPTER 2 - FIRST LAW OF THERMODYNAMICS 1. At the inlet to a certain nozzle the enthalpy of fluid passing is 2800 kj/kg, and the velocity is 50 m/s. At the discharge end the enthalpy is 2600 kj/kg. The

More information

Overview on use of a Molten Salt HTF in a Trough Solar Field

Overview on use of a Molten Salt HTF in a Trough Solar Field Overview on use of a Molten Salt HTF in a Trough Solar Field D. Kearney Kearney & Associates U. Herrmann, P. Nava Flabeg Solar International B. Kelly Nexant, Inc. R. Mahoney, J. Pacheco Sandia Natl Labs

More information

CONTROL VOLUME ANALYSIS USING ENERGY. By Ertanto Vetra

CONTROL VOLUME ANALYSIS USING ENERGY. By Ertanto Vetra CONTROL VOLUME ANALYSIS USING ENERGY 1 By Ertanto Vetra Outlines Mass Balance Energy Balance Steady State and Transient Analysis Applications 2 Conservation of mass Conservation of mass is one of the most

More information

AUXILIARY POWER MEASUREMENT, OPTIMIZATION & ANALYSIS. Steag Energy Training Center EEC WORKSHOP to

AUXILIARY POWER MEASUREMENT, OPTIMIZATION & ANALYSIS. Steag Energy Training Center EEC WORKSHOP to AUXILIARY POWER MEASUREMENT, OPTIMIZATION & ANALYSIS Steag Energy Training Center EEC WORKSHOP-25.09.2013 to 27.09.2013 Heat Input into a Large Coal Fueled Power Plant- Sub Critical design. 3% Stack Clean-up

More information

Pinch Analysis for Power Plant: A Novel Approach for Increase in Efficiency

Pinch Analysis for Power Plant: A Novel Approach for Increase in Efficiency Pinch Analysis for Power Plant: A Novel Approach for Increase in Efficiency S. R. Sunasara 1, J. J. Makadia 2 * 1,2 Mechanical Engineering Department, RK University Kasturbadham, Rajkot-Bhavngar highway,

More information

GREEN THREAD Piping Systems

GREEN THREAD Piping Systems Bulletin No. A1300 February 15, 2006 SMITH FIBERCAST GREEN THREAD Piping Systems PRODUCT GREEN THREAD pipe is filament wound using an amine cured epoxy resin and fiberglass and has a resin-rich liner reinforced

More information

Introduction To Computational Fluid Dynamics. Presented by Marc Laing CFD Team Manager

Introduction To Computational Fluid Dynamics. Presented by Marc Laing CFD Team Manager Introduction To Computational Fluid Dynamics Presented by Marc Laing CFD Team Manager Slide 1 50 years research in fluid and thermodynamics Flow meter calibration and development testing State-of-the-art

More information

CLOSED-LOOP HEAT EXCHANGER FOR GROUND COUPLED HEAT PUMPS

CLOSED-LOOP HEAT EXCHANGER FOR GROUND COUPLED HEAT PUMPS Bulletin of the Transilvania University of Braşov Vol. () - 0 Series : Special Issue No. CLOSED-LOOP HEAT EXCHANGER FOR GROUND COUPLED HEAT PUMPS G. DRAGOMIR I. BOIAN V. CIOFOAIA Abstract: Hydraulic imbalances

More information

Tapered-Bean Steam Chokes Revisited

Tapered-Bean Steam Chokes Revisited Tapered-Bean Steam Chokes Revisited Suzanne Castrup, Integrated Sciences Group; Faisal Latif, Vintage Production California LLC; and Ali Al Kalbani, Occidental Petroleum Corporation Summary Controlling

More information

Optimization of parameters for heat recovery steam generator (HRSG) in combined cycle power plants

Optimization of parameters for heat recovery steam generator (HRSG) in combined cycle power plants Optimization of parameters for heat recovery steam generator (HRSG) in combined cycle power plants Muammer Alus, Milan V. Petrovic - Faculty of Mechanical Engineering Laboratory of Thermal Turbomachinery

More information

Thermal Hydraulic Simulations of the Angra 2 PWR

Thermal Hydraulic Simulations of the Angra 2 PWR Thermal Hydraulic Simulations of the Angra 2 PWR Javier González-Mantecón, Antonella Lombardi Costa, Maria Auxiliadora Fortini Veloso, Claubia Pereira, Patrícia Amélia de Lima Reis, Adolfo Romero Hamers,

More information

CFD on Small Flow Injection of Advanced Accumulator in APWR

CFD on Small Flow Injection of Advanced Accumulator in APWR 54 CFD on Small Flow Injection of Advanced Accumulator in APWR TOMOSHIGE TAKATA TAKAFUMI OGINO TAKASHI ISHIBASHI TADASHI SHIRAISHI The advanced accumulator in the advanced pressurized-water reactor is

More information

CUSTODY TRANSFER FLOW MEASUREMENT WITH NEW TECHNOLOGIES. Stephen A. Ifft McCrometer Inc. Hemet, California, USA

CUSTODY TRANSFER FLOW MEASUREMENT WITH NEW TECHNOLOGIES. Stephen A. Ifft McCrometer Inc. Hemet, California, USA CUSTODY TRANSFER FLOW MEASUREMENT WITH NEW TECHNOLOGIES Stephen A. Ifft McCrometer Inc. Hemet, California, USA ABSTRACT New technologies can often bring advances to the operational processes within many

More information

Micro Hydro Turbine Test Facility at the NERDC

Micro Hydro Turbine Test Facility at the NERDC International Conference on Small Hydropower - Hydro Sri Lanka, -4 October 007 Micro Hydro Turbine Test Facility at the NERDC T.A.Wickramasinghe and M.Narayana Department of Renewable Energy, National

More information

Categorizing Units Based on Controllable Loss Parameters using PEPSE θ

Categorizing Units Based on Controllable Loss Parameters using PEPSE θ Categorizing Units Based on Controllable Loss Parameters using PEPSE θ Randolph M. Inman Allegheny Energy Supply Categorizing Units Based on Controllable Loss Parameters using PEPSE θ Randolph Inman Allegheny

More information

EXPERIMENTAL AERODYNAMICS FLOW TROUGH AN ORIFICE LAB SHEET

EXPERIMENTAL AERODYNAMICS FLOW TROUGH AN ORIFICE LAB SHEET EXPERIMENTAL AERODYNAMICS FLOW TROUGH AN ORIFICE LAB SHEET EMRE KOÇ ONUR GÜNEL 1- Introduction When a fluid passes through a constriction, such as through a sharp-edged hole or over a weir, the constriction

More information

Low temperature cogeneration using waste heat from research reactor as a source for heat pump

Low temperature cogeneration using waste heat from research reactor as a source for heat pump National Centre for Nuclear Research in Poland Low temperature cogeneration using waste heat from research reactor as a source for heat pump Anna Przybyszewska International Atomic Energy Agency 14-16

More information

Permanent Pressure Loss Comparison Among Various Flowmeter Technologies

Permanent Pressure Loss Comparison Among Various Flowmeter Technologies Permanent Pressure Loss Comparison Among Various Flowmeter Technologies by Stephen A. Ifft McCrometer Hemet, California, USA Abstract This paper explores the issue of permanent pressure loss through various

More information

2. Feeder pipe wall thinning mechanism and design modifications

2. Feeder pipe wall thinning mechanism and design modifications NDT in Canada 2016 & 6th International CANDU In-Service Inspection Workshop, Nov 15-17, 2016, Burlington, ON (Canada) www.ndt.net/app.ndtcanada2016 Third Qinshan Nuclear Power Plant Feeder Pipe design

More information

ES Fluid & Thermal Systems Page 1 of 6 STEAM TURBINE LABORATORY

ES Fluid & Thermal Systems Page 1 of 6 STEAM TURBINE LABORATORY ES 202 - Fluid & Thermal Systems Page 1 of 6 STEAM TURBINE LABORATORY Objective The objective of this laboratory experience is to demonstrate how mechanical power can be generated using a steam turbine

More information

Production Test Analysis Using Separator Method with Respect to Separator Efficiency

Production Test Analysis Using Separator Method with Respect to Separator Efficiency PROCEEDINGS, 43rd Workshop on Geothermal Reservoir Engineering Stanford University, Stanford, California, February 12-14, 2018 SGP-TR-213 Production Test Analysis Using Separator Method with Respect to

More information

Lecture No.3. The Ideal Reheat Rankine Cycle

Lecture No.3. The Ideal Reheat Rankine Cycle Lecture No.3 The Ideal Reheat Rankine Cycle 3.1 Introduction We noted in the last section that increasing the boiler pressure increases the thermal efficiency of the Rankine cycle, but it also increases

More information

Hitachi H-25 & H-80 Gas Turbine. Bucharest, Apr.23, 2013

Hitachi H-25 & H-80 Gas Turbine. Bucharest, Apr.23, 2013 Hitachi H-25 & H-80 Gas Turbine Bucharest, Apr.23, 2013 Doc No. : GKKP-13-009 Rev.0 Hitachi, Ltd. 2013. All rights reserved. 1 Table of Contents Hitachi Gas Turbine Business H-25 Performance and Applications

More information

System Analysis of Pb-Bi Cooled Fast Reactor PEACER

System Analysis of Pb-Bi Cooled Fast Reactor PEACER OE-INES-1 International Symposium on Innovative Nuclear Energy Systems for Sustainable Development of the World Tokyo, Japan, October 31 - November 4, 2004 System Analysis of Pb-Bi ooled Fast Reactor PEAER

More information

PVP INVESTIGATION OF A SHELL AND TUBE EXCHANGER IN LIQUEFIED NATURAL GAS VAPORIZATION SERVICE

PVP INVESTIGATION OF A SHELL AND TUBE EXCHANGER IN LIQUEFIED NATURAL GAS VAPORIZATION SERVICE ASME PVP 2007/CREEP 8 Conference 2007 ASME Pressure Vessels and Piping Division Conference July 22-26, 2007, San Antonio, Texas, USA PVP2007-26592 INVESTIGATION OF A SHELL AND TUBE EXCHANGER IN LIQUEFIED

More information

Venturi Tubes in Wet Gas Improved Models for the Over- Reading and the Pressure-Loss Ratio Method

Venturi Tubes in Wet Gas Improved Models for the Over- Reading and the Pressure-Loss Ratio Method Venturi Tubes in Wet Gas Improved Models for the Over- Reading and the Pressure-Loss Ratio Method Michael Reader-Harris, TUV NEL Emmelyn Graham, TUV NEL 1 INTRODUCTION Venturi tubes are one of the most

More information

FLEXI BURN CFB WP4: Boiler design and performance

FLEXI BURN CFB WP4: Boiler design and performance Development of High Efficiency CFB Technology to Provide Flexible Air/Oxy Operation for Power Plant with CCS FLEXI BURN CFB WP4: Boiler design and performance 2 nd Project Workshop, 6 th February 2013,

More information

Steam Cycle Chemistry in Air-Cooled Condensers. NV Energy ACC User s Group * November 12-13, 2009 Andrew Howell * Xcel Energy

Steam Cycle Chemistry in Air-Cooled Condensers. NV Energy ACC User s Group * November 12-13, 2009 Andrew Howell * Xcel Energy Steam Cycle Chemistry in Air-Cooled Condensers NV Energy ACC User s Group * November 12-13, 2009 Andrew Howell * Xcel Energy Steam Cycle Chemistry Goal for ACC: minimize corrosion of carbon steel Resulting

More information

FLOW MEASUREMENT Product Code 316 Instruction manual Contents

FLOW MEASUREMENT Product Code 316 Instruction manual Contents FLOW MEASUREMENT Product Code 316 Instruction manual Contents 1 Description 2 Specifications 3 Installation requirements 4 Installation Commissioning 5 Troubleshooting 6 Components used 7 Packing slip

More information

RELAP 5 ANALYSIS OF PACTEL PRIMARY-TO-SECONDARY LEAKAGE EXPERIMENT PSL-07

RELAP 5 ANALYSIS OF PACTEL PRIMARY-TO-SECONDARY LEAKAGE EXPERIMENT PSL-07 Fifth International Seminar on Horizontal Steam Generators 22 March 21, Lappeenranta, Finland. 5 ANALYSIS OF PACTEL PRIMARY-TO-SECONDARY LEAKAGE EXPERIMENT PSL-7 József Bánáti Lappeenranta University of

More information

Available online at ScienceDirect. Procedia Engineering 102 (2015 )

Available online at  ScienceDirect. Procedia Engineering 102 (2015 ) Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 102 (2015 ) 1056 1063 The 7th World Congress on Particle Technology (WCPT7) AN EXPERIMENTAL STUDY ON A HORIZONTAL ENERGY-SAVING

More information

SKYLINE FLOW CONTROLS INC.

SKYLINE FLOW CONTROLS INC. SKYLINE FLOW CONTROLS INC. SFC Skyline Flow Controls Venturi Meter (SFC-FV) The SFC Venturi Tube is a differential pressure flow element that accurately measures the flows of liquids or gases. SFC utilizes

More information

DEVELOPMENT OF STEAM INJECTOR FEEDWATER HEATER SYSTEM

DEVELOPMENT OF STEAM INJECTOR FEEDWATER HEATER SYSTEM 7th International Conference on Nuclear Engineering Tokyo, Japan, April 19-23, 1999 ICONE-7371 DEVELOPMENT OF STEAM INJECTOR FEEDWATER HEATER SYSTEM Shuichi Ohmori* and Michitugu Mori, Tokyo Electric Power

More information

READ ONLY. Adopting Agency BSC SFM. Adopt Entire Chapter Adopt Entire Chapter as amended (amended sections listed below)

READ ONLY. Adopting Agency BSC SFM. Adopt Entire Chapter Adopt Entire Chapter as amended (amended sections listed below) CALIFORNIA PLUMBING CODE MATRIX ADOPTION TABLE APPENDIX C - ALTERNATE PLUMBING SYSTEMS (Matrix Adoption Tables are non-regulatory, intended only as an aid to the user. See Chapter 1 for state agency authority

More information

NPP Simulators Workshop for Education - Passive PWR NPP & Simulator Overview

NPP Simulators Workshop for Education - Passive PWR NPP & Simulator Overview NPP Simulators Workshop for Education - Passive PWR NPP & Simulator Overview Wilson Lam (wilson@cti-simulation.com) CTI Simulation International Corp. www.cti-simulation.com Sponsored by IAEA Modified

More information

Status report Chinese Supercritical Water-Cooled Reactor (CSR1000)

Status report Chinese Supercritical Water-Cooled Reactor (CSR1000) Status report Chinese Supercritical Water-Cooled Reactor (CSR1000) Overview Full name Chinese Supercritical Water-Cooled Reactor Acronym CSR1000 Reactor type Pressurized Water Reactor (PWR) Coolant Supercritical

More information

GLAUNACH THE SILENCER HANDBOOK INSULATION SUPPLEMENTARY ACOUSTIC SHIELDING OF SILENCERS, PIPES & CO GLAUNACH GMBH ALL RIGHTS RESERVED -

GLAUNACH THE SILENCER HANDBOOK INSULATION SUPPLEMENTARY ACOUSTIC SHIELDING OF SILENCERS, PIPES & CO GLAUNACH GMBH ALL RIGHTS RESERVED - GLAUNACH THE SILENCER HANDBOOK INSULATION SUPPLEMENTARY ACOUSTIC SHIELDING OF SILENCERS, PIPES & CO GLAUNACH GMBH 2010 - ALL RIGHTS RESERVED - Part VIII page 2 of 9 There are two main motivations for adding

More information

Contour K5 Technical Information

Contour K5 Technical Information Contour K5 Technical Information 45.00 Y Design Time Line, Flow Test Data and Information Supporting AGA-3 / API 14.3 (2000 Edition) Compliance 22.50 Ø 0.500D Ø 0.850D X FLANGE FACE SERRATED SPIRAL FINISH

More information

The Locomotive. A Copper-Plated Thief: The Problem of Copper Deposits in Turbines

The Locomotive. A Copper-Plated Thief: The Problem of Copper Deposits in Turbines A Copper-Plated Thief: The Problem of Copper Deposits in Turbines By Dave Daniels and John Latcovich, The Hartford Steam Boiler Introduction Operators at a coal-fired, 2,600 PSI power plant performed monthly

More information

Workgroup Thermohydraulics. The thermohydraulic laboratory

Workgroup Thermohydraulics. The thermohydraulic laboratory Faculty of Mechanical Science and Engineering Institute of Power Engineering Professorship of Nuclear Energy and Hydrogen Technology Workgroup Thermohydraulics The thermohydraulic laboratory Dr.-Ing. Christoph

More information

St.MARTIN S ENGINEERING COLLEGE Dhulapally,Secunderabad,

St.MARTIN S ENGINEERING COLLEGE Dhulapally,Secunderabad, St.MARTIN S ENGINEERING COLLEGE Dhulapally,Secunderabad, 500014. MECHANICAL ENGINEERING TUTORIAL QUESTION BANK Course Name : THERMAL ENGINEERING II Course Code : A50326- Class : III B. Tech I Semester

More information

HYDRAULIC DEMONSTRATION CHANNEL

HYDRAULIC DEMONSTRATION CHANNEL HYDRAULIC DEMONSTRATION CHANNEL PACKING LIST Pitot-Static Tube and Manometer Tube Flow Meters 1. 48 Long Differential Manometer 2. Clear Tubing 3. Pitot-static Tube Clamp 4. Pitot-static Tube 1. Venturi

More information

NEW LP TURBINES FOR NE KRŠKO

NEW LP TURBINES FOR NE KRŠKO NEW LP TURBINES FOR NE KRŠKO Krešimir Nemčić, Martin Novšak NE Krško Vrbina 12, 8270 Krško, Slovenia kresimir.nemcic@nek.si, martin.novsak@nek.si ABSTRACT During the evaluation of possible future maintenance

More information

Flow Characterization of a Piezo-Electric High Speed Valve

Flow Characterization of a Piezo-Electric High Speed Valve Flow Characterization of a Piezo-Electric High Speed Valve T. Takiya*, N. Fukuda*, M. Yaga** and M. Han*** *( Hitachi Zosen Corporation, Osaka 551-0022, Japan) ** (Department of Mechanical Systems Engineering,

More information

Nuclear Power Plant Safety Basics. Construction Principles and Safety Features on the Nuclear Power Plant Level

Nuclear Power Plant Safety Basics. Construction Principles and Safety Features on the Nuclear Power Plant Level Nuclear Power Plant Safety Basics Construction Principles and Safety Features on the Nuclear Power Plant Level Safety of Nuclear Power Plants Overview of the Nuclear Safety Features on the Power Plant

More information

DS-4018 English Rev. FA. ProPlate Flowmeter Mass ProPlate Flowmeter Model 1195 Integral Orifice

DS-4018 English Rev. FA. ProPlate Flowmeter Mass ProPlate Flowmeter Model 1195 Integral Orifice 00813-0100-4686 DS-4018 English Rev. FA ProPlate Flowmeter Mass ProPlate Flowmeter Model 1195 Integral Orifice ProPlate Flowmeter Mass ProPlate Flowmeter Model 1195 Integral Orifice DP FLOW - THE INDUSTRY

More information