Performance of Thermoplastic Elastomeric and Thermoset Insulators under Accelerated Acid Rain Multistress Conditions

Size: px
Start display at page:

Download "Performance of Thermoplastic Elastomeric and Thermoset Insulators under Accelerated Acid Rain Multistress Conditions"

Transcription

1 Performance of Thermoplastic Elastomeric and Thermoset Insulators under Accelerated Acid Rain Multistress Conditions Raji Sundararajan, Victor Godinez and Muhammad Amin Abstract Polymers are becoming the material of choice for high voltage outdoor insulators. However being mostly organic, they are susceptible to aging and degradation (weathering) due to environmental (and electrical) stresses. This necessitates the study of their long-term behavior. It is desirable to study the long-term performance of the insulators in the service environment under multistress conditions encountered by the insulators to better simulate the actual conditions. This paper presents the results of the studies of a novel, third generation, environmental friendly thermoplastic elastomeric (TPE) insulators and conventional thermoset silicone rubber (SiR) insulators in Connecticut, USA and Taxila, Pakistan. 28 and 10kV insulators were used for this purpose. The aging phenomena were characterized by visual observations, hydrophobicity classification and using sophisticated materials analysis techniques, such as FTIR. The results indicated that the TPE insulators had discoloration and arcing after two thousand hours of aging while the silicone rubber insulators had no arcing. II. BACKGROUND Aging and degradation of polymers in normal and high voltage outdoor insulator applications is due essentially to the combined action of sunlight, especially low wavelength, high energy UV radiation [4, 5, 9]. Additionally, it has been observed that acid rain, containing NO 2 and SO 2 in trace quantities in air (acid rain) may also have a significant effect in shortening the useful life of certain polymers. Acid rain (with a ph < 5.6) refers to rain, fog and snow falling from atmosphere that is acidic. Sulfur dioxide (SO 2 ) and nitrogen oxides (NO x ) are the primary causes of acid rain. The effects of acid rain have been observed around the world (Fig. 1) [10]. Index Terms multistress aging, acid rain, polymeric insulators I. INTRODUCTION Acid rain can deteriorate high voltage outdoor insulators and affect their performance in addition to their other surface degrading effects [1-4]. Polymeric insulators can especially be susceptible since they are mostly organic [5-6]. It is of practical interest to study the aging and degradation characteristics of commercially available polymeric insulators under acid rain + multistress conditions, simulating an actual service environment. Presented in this paper are the results of the studies on the effect of acid rain (ph 3.9) in the Connecticut area, USA [1] and at Taxila, Pakistan. Connecticut was chosen as failure of polymeric coating, Room Temperature Vulcanized (RTV) silicone rubber was observed within 6 years of in service performance in service under extra high voltage of 345kV [1, 7]. It is of practical interest to study the performance of High Temperature Vulcanized (HTV) silicone rubber (SiR) insulators in this environment at a lower voltage as distribution class insulators are more commonly used. Additionally, it was also intended to compare the performance of thermoset (SiR) and thermoplastic elastomeric (TPE) materials [8]. Manuscript received October 14, R. Sundararajan was with Electronic Systems Dept., Arizona State University Poly, Mesa, AZ and is with Electrical & Computer Eng. Technology Dept., Purdue University, W. Lafayette, IN-47907, raji@purdue.edu V. Godinez was with Electronic Systems Dept., Arizona State University Poly, Mesa, AZ M. Amin is with Electrical Engineering Dept., University of Engineering & Technology, Taxila, Pakistan Fig. 1: Examples of polluted cities around the World [10]. Acid rain can deteriorate high voltage outdoor insulator performance also [1-4, 8] in addition to their other environmental degrading effects. Reports of acid rain related aging and degradation RTV silicone rubber coatings showed that the material had depolymerized and became putty-like after 6 years of service in a 345kV switchyard located near Long Island Sound [1, 7]. It had lost its physical integrity. Aging by a combination of chemical, photochemical (weathering) and electrochemical mechanisms could be the reason is suspected. It was proposed to study this weathering effect on the performance of 28kV distribution class polymeric insulators under accelerated multistress laboratory conditions [11]. Silicones being a thermoset polymeric material, it was also proposed to compare the performance of a 28kV two part thermoplastic elastomeric insulators with a silicone rubber insulator. Various stresses, such as UV radiation, heat (temperature), and acid rain, were used for aging. The multistress chamber at ASU East [8] was used to study various environmental conditions and to perform the accelerated test in much less time than in reality. Three 28kV insulators, two TPE and one silicone rubber were used for this purpose and their arrangement is shown in Fig. 2. The aging was performed for 2304h. UVA radiation, temperature 356

2 (40 o C) and acid rain were the various stress applied. Voltage was on all the time in both cycles. The ph of the acid rain used was 3.9 [1] and the acid rain was prepared using NH 4 Cl, NaCl, KCl, HNO 3, MgSO 4, and CaSO 4 [3]. Table I gives the insulator dimensions and Table II gives the acid rain preparation details. Fig. 3: Schematic of the Experimental Test Set-up inside a chamber of 0.6x0.6x0.6m 3. Fig. 2: Experimental set up of Connecticut insulators. The insulators are TPE 1, SiR 2 and TPE 3 from left to right. TABLE I Geometer Details of the 28kV Polymeric Insulators Item TPE Silicone Rubber Leakage Distance, mm Diameter of shed, mm Diameter of sheath, mm Dry Arc Distance (mm) TABLE II Acid Rain preparation (ph 3.9) Chemicals Quantity, g/l NaCl KCl HNO MgSO CaSO In Pakistan, the acid rain + multistress effect was studied using 10kV silicone rubber insulators (Table III). The service environment chosen was Taxila, which is about 40km from Islamabad. The various stresses applied are shown in Table IV. This illustrates the weather cycle that was designed to simulate the environment [12] of the capital city Islamabad and surroundings using available data of meteorological department [12]. The applied stresses were set above normal environmental stresses to simulate accelerated conditions. The aging was conducted for a period of 30days (720h) using a plastic chamber of 0.6x0.6x0.6m 3 (Fig. 3). Two samples, each of rod, plate and full scale 10kV insulator were used. One sample of each type was energized and the other kept un-energized. UV radiation level at 4.16mW/cm 2 was applied using UV lamps fitted on three sides of the chamber. A spray gun was fitted on one side of the chamber to apply artificial acidic rain. The diameter of nozzle was 0.5mm and spraying pressure was 3.0kg/cm 2. The rate of rain was 0.5 liter/hour. The applied voltage was 10kV (line to ground). The arrangement of complete setup is shown in Fig. 3. TABLE III Geometer Details of the 10kV Silicone Rubber Insulators Item Dimension Leakage Distance, mm 521 Diameter of larger shed, mm 156 Diameter of sheath, mm 28 Dry Arc Distance (mm) 391 Number of sheds 4 Distance between the sheds, mm 60 TABLE IV Islamabad Weather cycle. Serial No. Time of the Operation Operation day time 1 7:00 pm to 12h UV radiation o C 7:00 am 2 7:00 am to 4h rest 11:00 am 3 11:00 am to 1/2h rain spray 11:30 am 4 11:30 am to 7:00 pm 71/2h rest III. RESULST & DISCUSSION A. Connecticut acid rain aging There was discoloration in both TPE and SiR insulators. The TPE material lost its hydrophobicity while SiR retained it. There was hardware corrosion in the TPE insulator 3 (Fig. 2). Figs. 4-6 show the various degradations observed in the insulators. Fig. 4 shows the various surface changes and Fig. 5 shows the Fourier Transform Infra-Red Spectroscopy (FTIR) spectrographs after 1152h aging. There was loss of hydrocarbons in both insulating materials indicating the deteriorating effect of acid rain + multistress on these materials. Fig. 6 shows the arcing in TPE 1 insulator. There was arcing also on TPE 3 insulator. The SiR insulator had no arcing. B. Taxila acid rain aging 1) Visual observations: No cracking, chalking, erosion and discoloration were found after 5 th and 10 th days. On the 17 th day, severe discoloration was found at the top shed of insulator as is shown in Fig. 7(a), (b) and (c). This discoloration was uniform on all the sheds, and there was no discoloration on the core. This might be due to the high 357

3 conductivity and low ph value of the acid rain on the insulating material. The electrical stress would accelerate the aging/degradation. This may lead to increased tracking and consequently more leakage current [13, 14]. Fig. 4a: Photographs illustrating the hydrophobicity and other surface aging characteristics of the insulators after 240h. Fig. 4b: Photographs illustrating the hydrophobicity and other surface aging characteristics of the insulators after 816h. Fig. 4c: Photographs illustrating the hydrophobicity and other surface aging characteristics of the insulators after 1392h. 2) Hydrophobicity: The surface conditions per STRI hydrophobicity classifications [15] are given in Table V. Fig. 8 shows the nature of the surface after 24 days. CH 3 methyl groups are responsible for hydrophobic behavior of silicone rubber material. When the number of such groups increases on the surface, it improves hydrophobicity characteristics and vice versa. Thus, with the variation in the surface nature, the hydrophobicity, and hence the leakage current and the FTIR spectra vary. Thus, the hydrophobicity of the sample can be related to the absorption value of CH 3 at wave number 1258cm -1. Table VI lists the percent decrease in absorption of C-H bond at wave number 1258cm -1 for the energized insulator, illustrating the recovery behavior during aging. 3) FTIR: The absorptions at 2962cm -1 refer to the C-H bond of methyl CH 3, cm -1 refer to the Si-CH3 bond and cm -1 to the Si-O-Si main bond. The values of absorption at these wave numbers and the percent changes are shown in Table VI. The increase and decrease of absorption of the C-H bond of CH 3 and Si-CH 3 mean that the number of C-H bonds increased and decreased at the various stages and periods of aging. 4) Leakage Current: In this investigation, leakage current was also monitored regularly. Normally, the leakage current was of the order of 0.1mA, but during rainfall increased leakage current activities were noticed and the magnitude of the leakage current was in the range of mA. This could be due to the high conductivity of acidic rain. The magnitude of leakage current still remained within a few ma, illustrating that the integrity of the insulators are intact. This is also in line with the FTIR results and hydrophobicity performance observed in the present study. These findings correlate well with previous results [13]. 358

4 Virgin SIR Virgin TPE Virgin TPE ch3 ch1hvsum11/06 ch1lvsum11/06 ch2sirhvsum11/06 ch2sirlvsum11/06 ch3lvsum11/06 ch3hvsum11/06 %Transmittance Wavenumbers (cm-1) 1000 Fig. 5 FTIR spectrographs illustrating the peak heights of various bonds of TPE and SiR after 1152h aging at Connecticut multistress conditions Fig. 6: TPE Insulator with arcing and SiR insulator 9with no arcing) after 2304h aging. (a) After 17 days (b) after 24 days (c) after 30 days Fig. 7 Photographs illustrating the gradual discoloration and surface changes observed. TABLE V Hydrophobicity Classification of the 10kV Insulators Days of aging Hydrophobicity classification (HC) Top Shed Bottom shed 20 HC 3-4 HC 2 24 HC 2 HC HC 4 HC 4 359

5 Fig. 8: Hydrophobicity after 24days of aging. TABLE VI Absorption of different chemical groups at Taxila multistress aging Insulator status Absorption At 2962 cm -1 At 1258 cm -1 At 1008 cm -1 Original After initial five days % change in absorption After ten days % change in absorption After fifteen days % change in absorption After twenty days % change in absorption After twenty five days % change in absorption IV. CONCLUSIONS The 2304h acid rain + multistress aging study conducted at multistress conditions simulating Connecticut, USA indicated discoloration, loss of hydrophobicity and degradation of the surfaces (FTIR spectrographs) of the 28kV TPE insulators. There were arcing after 2000h and one of the TPE insulators (TPE 3) had severe hardware corrosion too. The 28kV silicone rubber insulators had discoloration, less loss of hydrophobicity and no arcing The 720h acid rain + multistress aging study conducted at multistress conditions, simulating Taxila, Pakistan using 10kV silicone rubber thermoset insulators also showed similar findings as USA study; there was discoloration and erosion of the thermoset silicone rubber polymer. The hydrophobicity was HC 4. The leakage current levels were low, at 2.7mA. These insulator aging characteristics depicted a periodic nature i.e. a cycle of degradation and restoration of the surface. This indicates the dynamic nature of the aging kinetics The major merit of these studies is that they investigate the whole insulator system for long term stress under multistress conditions that simulate the in service environment as closely as possible, not just the material, and thus, the results could be directly translated to the field conditions. [2] X. Wang, S. Kumagai, and N. Yoshimura, Contamination performance of silicone rubber insulator subjected to acid rain, IEEE Trans. DEI, Vol. 5, No. 6, Dec [3] P.A. Calva, E. Perez Ruiz, M.G. Marquez, and G.P. Cabrera, Measuring and Analysis of the effect of acid rain in polluted polymer insulators at high altitude, CEIDP [4] N.E. Frost, P.B. McGrath, and C.W. Burns, Accelerated aging of insulators under acid rain conditions, CEIDP [5] N. Grassie and G. Scott, Polymer Degradation and Stabilization, Cambridge University Press, New York, [6] P. P. Klemchuk, Editor, Polymer Stabilization and Degradation, ACS Symposium Series, American Chemical Society, Washington, D.C., [7] K. Eldridge, et al., Degradation of Silicone-Based Coating in a Substation-Application, IEEE Trans. PWRD, Vol. 14, No. 1, Jan 1999, pp [8] C. Olave et al., Influence of Acid Rain + Multistress Conditions on the Long Term Performance of 28kV Polymeric Insulators, IEEE International Conference on Electrical Insulation & Dielectric Phenomena, Oct [9] T. J. Lewis, Aging A Perspective, IEEE Electrical Insulation Magazine, Vol. 17, No. 4, July/August 2001, pp [10] [11] H.M. Schneider, W.W. Guidi, J.T. Burnham, R.S. Gorur, and J.F. Hall, Accelerated aging and flashover tests on 138kV nonceramic line insulators, IEEE Trans. PWRD, Vol. 8, No. 1, Jan 1993, pp [12] ADB RETA5555- Environment statistics of Pakistan [13] X.Wang, S.Kumagai and N. Yoshimura, Contamination performance of silicone rubber insulator subjected to acid rain, IEEE Transactions on Dielectric and Electrical Insulation, Vol. 5 No. 6, pp , December [14] J. Burnham, Guidelines for visual identification of damaged polymer insulators, Transmission Dept, June Beach, FL, Nov [15] Guideline for visual identification of deterioration and damages on suspension composite insulators, STRI Guide 5, REFERENCES [1] H. Homma, C.L. Mirley, J. Ronzella, and S.A. Boggs, Field and Laboratory Aging of RTV Silicone Insulator Coatings, IEEE Trans. PWRD, Vol. 15, No. 4, Oct 2000, pp

Artificial Accelerated Ageing Test of Silicone Rubber Housing Material for Lightning Arrester

Artificial Accelerated Ageing Test of Silicone Rubber Housing Material for Lightning Arrester Artificial Accelerated Ageing Test of Silicone Rubber Housing Material for Lightning Arrester W. Payakcho, J. Grasaesom, S. Thong-om and B. Marungsri* Abstract This paper presents the experimental results

More information

Laboratory Investigation on Hydrophobicity and Tracking performance of Field Aged Composite Insulators

Laboratory Investigation on Hydrophobicity and Tracking performance of Field Aged Composite Insulators Laboratory Investigation on Hydrophobicity and Tracking performance of Field Aged Composite Insulators N. Mavrikakis Faculty of Engineering Aristotle University of Thessaloniki nmavrika@auth.gr K. Siderakis

More information

Comparative study on field collected samples of aged silicon rubber composite coatings for high voltage insulators

Comparative study on field collected samples of aged silicon rubber composite coatings for high voltage insulators DOI: 10.2478/achi-2013-0009 ACTA CHEMICA IASI, 21_2, 93-106 (2013) Comparative study on field collected samples of aged silicon rubber composite coatings for high voltage insulators I.V. Tudose, 1,4 M.

More information

COASTAL INDIA. Supply & Application of: Epsilon Midsun 570 Gen-4 RTV HVIC (High Voltage Insulator Coating) and

COASTAL INDIA. Supply & Application of: Epsilon Midsun 570 Gen-4 RTV HVIC (High Voltage Insulator Coating) and Supply & Application of: Epsilon Midsun 570 Gen-4 RTV HVIC (High Voltage Insulator Coating) and Epsilon Midsun 579 RTV Anti-Corrosion Coating In COASTAL INDIA Supply & Application of 8,000kg of Epsilon

More information

Laboratory Investigation on Hydrophobicity of New Silicon Rubber Insulator under Different Environmental Conditions

Laboratory Investigation on Hydrophobicity of New Silicon Rubber Insulator under Different Environmental Conditions International Journal of Electrical & Computer Sciences IJECS-IJENS Vol: 12 No: 03 1 Laboratory Investigation on Hydrophobicity of New Silicon Rubber Insulator under Different Environmental Conditions

More information

Performance Analysis of 33 kv Polymer and Porcelain Insulators under Various Pollution Conditions at Costal Regions

Performance Analysis of 33 kv Polymer and Porcelain Insulators under Various Pollution Conditions at Costal Regions Volume 114 No. 9 217, 1-9 ISSN: 1311-88 (printed version); ISSN: 1314-3395 (on-line version) url: http://www.ijpam.eu ijpam.eu Performance Analysis of 33 kv Polymer and Porcelain Insulators under Various

More information

Polymer Suspension Insulators 69kV to 765kV

Polymer Suspension Insulators 69kV to 765kV CATALOG Polymer Suspension Insulators 69kV to 765kV NGK Locke Polymer Insulators, Inc. Virginia Beach, Virginia, U.S.A. TABLE of CONTENTS Table of Contents... 1 Design Features... 2 Material... 2 Definition

More information

The Role of Inorganic Fillers in Silicone Rubber for Outdoor Insulation Alumina Tri-Hydrate or Silica

The Role of Inorganic Fillers in Silicone Rubber for Outdoor Insulation Alumina Tri-Hydrate or Silica F E A T U R E A R T I C L E The Role of Inorganic Fillers in Silicone Rubber for Outdoor Insulation Alumina Tri-Hydrate or Silica Key Words: Silicone rubber, fillers, alumina tri-hydrate, silica, erosion

More information

HIGH VOLTAGE INSULATORS. By JP Holtzhausen. Glass. Bushings & hollow core insulators. Cap & pin insulators

HIGH VOLTAGE INSULATORS. By JP Holtzhausen. Glass. Bushings & hollow core insulators. Cap & pin insulators HIGH VOLTAGE INSULATORS By JP Holtzhausen The principal dielectric used on overhead power lines is air at atmospheric pressure. The air, surrounding the bare high voltage aluminium or steel- cored aluminium

More information

UNS 5kA Arrester. Certified Test Report IEC

UNS 5kA Arrester. Certified Test Report IEC CP No.: CP0504 Page 1 of 10 UNS 5kA Arrester Certified Test Report IEC 60099-4 2004 CERTIFICATION Statements made and data shown are, to the best of our knowledge and belief, correct and within the usual

More information

Energy Division Insulators

Energy Division  Insulators Energy Division http://energy.tycoelectronics.com Insulators R Insulators Tyco Electronics Energy Division covers a wide range of polymeric, hybrid and porcelain insulators. For decades all these products

More information

Mapping HV Insulators Pollution in the Mediterranean Island of Crete

Mapping HV Insulators Pollution in the Mediterranean Island of Crete 1 Mapping HV Insulators Pollution in the Mediterranean Island of Crete D. Pylarinos, K. Siderakis, N. Mavrikakis, E. Thalassinakis Abstract The reliability of High Voltage insulators is rather important

More information

Investigation of leakage current flow through wooden poles structures on overhead distribution system

Investigation of leakage current flow through wooden poles structures on overhead distribution system Proceedings of the 7th WSEAS International Conference on Power Systems, Beijing, China, September 15-17, 2007 120 Investigation of leakage current flow through wooden poles structures on overhead distribution

More information

Polymer Insulators and Coatings in the Cretan Power System. The Transmission Line Case

Polymer Insulators and Coatings in the Cretan Power System. The Transmission Line Case Polymer Insulators and Coatings in the Cretan Power System. The Transmission Line Case D. Pylarinos Hellenic Electricity Distribution Network Operator dpylarinos@yahoo.com K. Siderakis Technological Educational

More information

Thermal Aging, Water Absorption, and Their Multiple Effects on Tracking Resistance of Epoxy for Outdoor Use

Thermal Aging, Water Absorption, and Their Multiple Effects on Tracking Resistance of Epoxy for Outdoor Use Electrical Engineering in Japan, Vol. 131, No. 3, 2000 Translated from Denki Gakkai Ronbunshi, Vol. 118-A, No. 11, November 1998, pp. 1255 1263 Thermal Aging, Water Absorption, and Their Multiple Effects

More information

Comparative Investigation of Silicone Rubber Composite and RTV Coated Glass Insulators Installed in Coastal Overhead Transmission Lines

Comparative Investigation of Silicone Rubber Composite and RTV Coated Glass Insulators Installed in Coastal Overhead Transmission Lines Comparative Investigation of Silicone Rubber Composite and RTV Coated Glass Insulators Installed in Coastal Overhead Transmission Lines Key words: glass insulators, RTV coated, leakage current, silicone

More information

TRANSMISSION & DISTRIBUTION SILICONE INSULATORS InterPhase Spacers 15 kv to 400 kv

TRANSMISSION & DISTRIBUTION SILICONE INSULATORS InterPhase Spacers 15 kv to 400 kv K-LINE INSULATORS LIMITED Catalogue TD-IPS TORONTO, ONTARIO, CANADA TRANSMISSION & DISTRIBUTION SILICONE INSULATORS InterPhase Spacers 15 kv to 400 kv ISO9001 SAI GLOBAL FILE No. 000117 Transmission &

More information

Measurement of Leakage Current for Monitoring the Performance of Outdoor Insulators in Polluted Environments

Measurement of Leakage Current for Monitoring the Performance of Outdoor Insulators in Polluted Environments F E A T U R E A R T I C L E Measurement of Leakage Current for Monitoring the Performance of Outdoor Insulators in Polluted Environments Key words: insulators, pollution, leakage current, diagnostic techniques,

More information

Pins Insulator. Composite/Polymers Insulators

Pins Insulator. Composite/Polymers Insulators Composite/Polymers Insulators Electric network in India operates under very harsh environments. Industrial pollution, marshy land, hilly and unfriendly terrain, extreme weather, coastal region etc. make

More information

Polymer Cutout Testing Recommendations

Polymer Cutout Testing Recommendations 1 Polymer Cutout Testing Recommendations High Voltage Fuse Subcommittee May 2012 Frank Lambert Recommended Tests 1. Water Diffusion Tests (CAN/CSA 310 09 7.3) 2. DyePenetration (ANSI C29.13 Section 7.3)

More information

WEATHERING AND CORROSION TESTING IN THE AUTOMOTIVE INDUSTRY: AN OVERVIEW OF TODAY S REQUIREMENTS. Andy Francis, Q-Lab Corporation

WEATHERING AND CORROSION TESTING IN THE AUTOMOTIVE INDUSTRY: AN OVERVIEW OF TODAY S REQUIREMENTS. Andy Francis, Q-Lab Corporation WEATHERING AND CORROSION TESTING IN THE AUTOMOTIVE INDUSTRY: AN OVERVIEW OF TODAY S REQUIREMENTS Andy Francis, Q-Lab Corporation 17M-0479 1 Weathering and Corrosion Weathering (Atmospheric) Corrosion Changes

More information

Midsun HVIC silicone is not affected by UV light, temperature, corrosive environments, or ATH pitting from dry band arcing.

Midsun HVIC silicone is not affected by UV light, temperature, corrosive environments, or ATH pitting from dry band arcing. Midsun 570 Midsun HVIC silicone is not affected by UV light, temperature, corrosive environments, or ATH pitting from dry band arcing. Because the coating is highly water repellent, contaminant s cannot

More information

Durability Evaluation of Highly Reflective Coating Materials for Roofing

Durability Evaluation of Highly Reflective Coating Materials for Roofing Durability Evaluation of Highly Reflective Coating Materials for Roofing Kenji Motohashi 1 Masataka Tamura 2 ABSTRACT Highly reflective coating materials for roofing (cool roof paints) are becoming popular

More information

Polymer Cutout Evaluation NEETRAC

Polymer Cutout Evaluation NEETRAC Polymer Cutout Evaluation NEETRAC Frank C. Lambert Georgia Tech / NEETRAC High Voltage Fuses Subcommittee Calgary, Alberta October 14, 2008 1 NEETRAC Members 2008-2009 1. 3M 2. ABB 3. ACA Conductor Accessories

More information

Electric Field and Potential Distribution in a 420 kv Novel Unibody Composite Cross-Arm

Electric Field and Potential Distribution in a 420 kv Novel Unibody Composite Cross-Arm 4 th Nordic Insulation Symposium on Materials, Components and Diagnostics Electric Field and Potential Distribution in a 4 kv Novel Unibody Composite Cross-Arm Jahangiri, Tohid ; Bak, Claus Leth ; Faria

More information

Surge arrester 3EB4. with polymeric composite housing for operating aboard traction units

Surge arrester 3EB4. with polymeric composite housing for operating aboard traction units Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to others without express authorization are prohibited. Offenders

More information

Accelerated Weatherability Testing The Right Choice

Accelerated Weatherability Testing The Right Choice Accelerated Weatherability Testing The Right Choice Presented by: Stephen Novak CRRC Membership Meeting February 13, 2006 Topics Weathering Testers: Simulating the Forces of Destruction Developing Accelerated

More information

Formation of hydrophobic coating on glass surface using atmospheric pressure non-thermal plasma in ambient air

Formation of hydrophobic coating on glass surface using atmospheric pressure non-thermal plasma in ambient air INSTITUTE OF PHYSICS PUBLISHING JOURNAL OF PHYSICS D: APPLIED PHYSICS J. Phys. D: Appl. Phys. 37 (2004) 2261 2266 PII: S0022-3727(04)77012-6 Formation of hydrophobic coating on glass surface using atmospheric

More information

Accelerated Testing and Durability. Qualifying your Industrial Anticorrosive Coatings

Accelerated Testing and Durability. Qualifying your Industrial Anticorrosive Coatings Accelerated Testing and Durability Qualifying your Industrial Anticorrosive Coatings Overview Static Test Methods Cyclic Test Methods Exterior Exposure Comparison of Accelerated Testing Evaluating a Coating

More information

Si-COAT 570 RTV Silicone HVIC. Reliability & Beyond. Seminar Presentation

Si-COAT 570 RTV Silicone HVIC. Reliability & Beyond. Seminar Presentation Si-COAT 570 RTV Silicone HVIC Reliability & Beyond Seminar Presentation Overview Background & industry pressures Early validation of Si-COAT HVIC The science of Si-COAT Q&A Si-COAT HVIC : The Background

More information

Industrial Coatings: HIGHLY DURABLE, SUPERHYDROPHOBIC AND OLEOPHOBIC. (White Paper) NeverWet LLC

Industrial Coatings: HIGHLY DURABLE, SUPERHYDROPHOBIC AND OLEOPHOBIC. (White Paper) NeverWet LLC Industrial Coatings: HIGHLY DURABLE, SUPERHYDROPHOBIC AND OLEOPHOBIC (White Paper) NeverWet LLC Background: Metal surfaces have high surface energy, are negatively charged, and hydrophilic as shown by

More information

Hot-Dip Galvanized Fabrication Considerations

Hot-Dip Galvanized Fabrication Considerations Hot-Dip Galvanized Fabrication Considerations TECHNICAL BULLETIN JANUARY 27, 2016 Forming Hot-dip galvanized sheet can be formed almost as readily as uncoated cold rolled sheet. It can be formed in a variety

More information

New Developments in Measuring Low Silicon in Process Piping Using Handheld X-ray Fluorescence (XRF)

New Developments in Measuring Low Silicon in Process Piping Using Handheld X-ray Fluorescence (XRF) New Developments in Measuring Low Silicon in Process Piping Using Handheld X-ray Fluorescence (XRF) Presented by: Mark Lessard Business Development Manager Thermo Fisher Scientific mark.lessard@thermofisher.com

More information

Instruction guide Medium Voltage equipment on sites exposed to high humidity and/or heavy pollution. Recommendations for installation and use

Instruction guide Medium Voltage equipment on sites exposed to high humidity and/or heavy pollution. Recommendations for installation and use Medium Voltage equipment on sites exposed to high humidity and/or heavy pollution Recommendations for installation and use Contents Introduction 2 Use of MV equipment 2 Normal service conditions for indoor

More information

Factors Affecting Current Ratings for Underground and Air Cables

Factors Affecting Current Ratings for Underground and Air Cables Factors Affecting Current Ratings for Underground and Air Cables S. H. Alwan, J. Jasni, M. Z. A. Ab Kadir, N. Aziz Abstract The aim of this paper is to present a parametric study to determine the major

More information

Study on the dc flashover performance of standard suspension insulator with ringshaped non-uniform pollution

Study on the dc flashover performance of standard suspension insulator with ringshaped non-uniform pollution High Voltage Research Article Study on the dc flashover performance of standard suspension insulator with ringshaped non-uniform pollution ISSN 2397-7264 Received on 28th June 2017 Revised 1st October

More information

The Role of Titanium Dioxide Pigments. In Outdoor Weathering of Rigid PVC

The Role of Titanium Dioxide Pigments. In Outdoor Weathering of Rigid PVC The Role of Titanium Dioxide Pigments In Outdoor Weathering of Rigid PVC DuPont Titanium Technologies Alex X. Gao, John D. Bolt, Andy A. Feng April 23, 28 Brighton Dome, UK 24 E.I. du Pont de Nemours and

More information

CIGRE 16 BRUGGE Partial Discharge and Dissolved Gas Analysis In bio-degradable transformer oil. The University of New South Wales Australia

CIGRE 16 BRUGGE Partial Discharge and Dissolved Gas Analysis In bio-degradable transformer oil. The University of New South Wales Australia CIGRE 16 BRUGGE 2007 Partial Discharge and Dissolved Gas Analysis In bio-degradable transformer oil D. IMAMOVIC *, K.X. LAI, N.A. MUHAMAD, B.T. PHUNG and T.R. BLACKBURN # The University of New South Wales

More information

Polymer Post Insulators for 46 to 500kV Applications

Polymer Post Insulators for 46 to 500kV Applications CATALOG 142 Polymer Post Insulators for 46 to 500kV Applications NGK-Locke Polymer Insulators, Inc. Virginia Beach, Virginia, U.S.A. TABLE of CONTENTS Process and Design Features...2 Materials...3 Application

More information

February 1, 2010 PARTIES INTERESTED IN EVALUATION REPORTS ON ROOF UNDERLAYMENTS FOR USE IN SEVERE CLIMATE AREAS

February 1, 2010 PARTIES INTERESTED IN EVALUATION REPORTS ON ROOF UNDERLAYMENTS FOR USE IN SEVERE CLIMATE AREAS February 1, 2010 TO: PARTIES INTERESTED IN EVALUATION REPORTS ON ROOF UNDERLAYMENTS FOR USE IN SEVERE CLIMATE AREAS SUBJECT: Proposed Revisions to the Acceptance Criteria for Roof Underlayments for Use

More information

Life cycle analysis of thermosyphon solar water heaters

Life cycle analysis of thermosyphon solar water heaters Life cycle analysis of thermosyphon solar water heaters Soteris A. KALOGIROU Department of Mechanical Engineering and Materials Sciences and Engineering Cyprus University of Technology, P. O. Box 50329,

More information

Surface Analysis of Electrochromic Switchable Mirror Glass Based on Magnesium-Nickel Thin Film in Accelerated Degradation Test

Surface Analysis of Electrochromic Switchable Mirror Glass Based on Magnesium-Nickel Thin Film in Accelerated Degradation Test Materials Transactions, Vol. 52, No. 3 (2011) pp. 464 to 468 #2011 The Japan Institute of Metals Surface Analysis of Electrochromic Switchable Mirror Glass Based on Magnesium-Nickel Thin Film in Accelerated

More information

INSULATORS NEW. See page J-4 for more information.

INSULATORS NEW. See page J-4 for more information. INSULATORS INSULATORS NEW Improved 23613 Dead End/Suspension Insulator Salisbury s Improved 23613 Dead End/Suspension Insulator has aluminum end fittings. These new end fittings create a lightweight product

More information

Silicone Elastomers Markets, Megatrends and Innovations

Silicone Elastomers Markets, Megatrends and Innovations CREATING TOMORROW`S SOLUTIONS Silicone Elastomers Markets, Megatrends and Innovations Peter Summo, Vice President Engineering Silicones Peter Summo, Engineering Silicones, June 28, 2016 0 of 14 WACKER

More information

A Technology for Enhanced Control of Erosion, Sediment and Metal Leaching at Disturbed Land Using Polyacrylamide and Magnetite Nanoparticles

A Technology for Enhanced Control of Erosion, Sediment and Metal Leaching at Disturbed Land Using Polyacrylamide and Magnetite Nanoparticles A Technology for Enhanced Control of Erosion, Sediment and Metal Leaching at Disturbed Land Using Polyacrylamide and Magnetite Nanoparticles Min Zheng and Dongye Zhao Environmental Engineering Program

More information

300mm Wafer Stain Formation by Spin Etching

300mm Wafer Stain Formation by Spin Etching 10.1149/1.2980313 The Electrochemical Society 300mm Wafer Stain Formation by Spin Etching K. Sato a, S. Mashimoto a, and M. Watanabe a a Process Development, SEZ Japan, Inc., Hongo, Bunkyo-ku 1130033,

More information

History of Cable Systems HISTORICAL OVERVIEW OF MEDIUM & HIGH VOLTAGE CABLES. Nigel Hampton

History of Cable Systems HISTORICAL OVERVIEW OF MEDIUM & HIGH VOLTAGE CABLES. Nigel Hampton HISTORICAL OVERVIEW OF MEDIUM & HIGH VOLTAGE CABLES Nigel Hampton Copyright GTRC 2012 Objective To present the evolution of cables in time to understand the lessons from the past: the legacy problems and

More information

Field-test at Betonstal Sp. z.o.o. Szczecin/ Poland

Field-test at Betonstal Sp. z.o.o. Szczecin/ Poland Field-test at Betonstal Sp. z.o.o. Szczecin/ Poland M. Schmidt, R. Brandenburg, A. Schwock Executive Summary Field experiments were performed in order to investigate the feasibility of the removal of gaseous

More information

Module-13. Corrosion and Degradation of materials

Module-13. Corrosion and Degradation of materials Module-13 Corrosion and Degradation of materials Contents 1) Corrosion of metals 2) Corrosion of ceramics 3) Degradation of polymers Deterioration of materials Conventional engineering materials are not

More information

Chemical analysis of insulator contaminants and Reliability improvement of T&D line for smart operation of grid under chemically polluted environment

Chemical analysis of insulator contaminants and Reliability improvement of T&D line for smart operation of grid under chemically polluted environment Chennai and Dr.MGR University Second International Conference on Sustainable Energy and Intelligent System (SEISCON 2011), Dr. M.G.R. University, Maduravoyal, Chennai, Tamil Nadu, India. July. 20-22, 2011.

More information

The principle Of Tungsten Inert Gas (TIG) Welding Process

The principle Of Tungsten Inert Gas (TIG) Welding Process The principle Of Tungsten Inert Gas (TIG) Welding Process This chapter presents the principle of tungsten inert gas (TIG) welding process besides important components of TIG welding system and their role.

More information

1 Characteristics of the Atmosphere

1 Characteristics of the Atmosphere CHAPTER 22 1 Characteristics of the Atmosphere SECTION The Atmosphere KEY IDEAS As you read this section, keep these questions in mind: What are the layers of Earth s atmosphere? How has Earth s atmosphere

More information

DURABILITY AND PERFORMANCE OF TITANIUM DIOXIDE IN PHOTOCATALYTIC PAVEMENTS

DURABILITY AND PERFORMANCE OF TITANIUM DIOXIDE IN PHOTOCATALYTIC PAVEMENTS DURABILITY AND PERFORMANCE OF TITANIUM DIOXIDE IN PHOTOCATALYTIC PAVEMENTS Marwa Hassan Performance Contractors Distinguished Assistant Professor Department of Construction Management 3128 Patrick Taylor

More information

STANDARD FOR EXTRUDED INSULATION POWER CABLES RATED ABOVE 46 THROUGH 345 KV. Approved by AMERICAN NATIONAL STANDARDS INSTITUTE.

STANDARD FOR EXTRUDED INSULATION POWER CABLES RATED ABOVE 46 THROUGH 345 KV. Approved by AMERICAN NATIONAL STANDARDS INSTITUTE. ANSI/ICEA S-108-720-2012 STANDARD FOR EXTRUDED INSULATION POWER CABLES RATED ABOVE 46 THROUGH 345 KV Approved by AMERICAN NATIONAL STANDARDS INSTITUTE November 27, 2012 Publication # ANSI/ICEA S-108-720-2012

More information

Thin AC-PDP Vacuum In-line Sealing Using Direct-Joint Packaging Method

Thin AC-PDP Vacuum In-line Sealing Using Direct-Joint Packaging Method H128 0013-4651/2004/151 5 /H128/5/$7.00 The Electrochemical Society, Inc. Thin AC-PDP Vacuum In-line Sealing Using Direct-Joint Packaging Method Duck-Jung Lee, a,b,z Seung-IL Moon, a Yun-Hi Lee, c and

More information

Etching Mask Properties of Diamond-Like Carbon Films

Etching Mask Properties of Diamond-Like Carbon Films N. New Nawachi Diamond et al. and Frontier Carbon Technology 13 Vol. 15, No. 1 2005 MYU Tokyo NDFCT 470 Etching Mask Properties of Diamond-Like Carbon Films Norio Nawachi *, Akira Yamamoto, Takahiro Tsutsumoto

More information

Synthetic Ester-Based Oils and Their Application in Power Industry

Synthetic Ester-Based Oils and Their Application in Power Industry European Association for the Development of Renewable Energies, Environment and Power Quality International Conference on Renewable Energies and Power Quality (ICREPQ 09) Valencia (Spain), 15th to 17th

More information

Just what is Acid Rain?

Just what is Acid Rain? Acid Rain Just what is Acid Rain? Acid Rain is the term used to describe the ways in which acid precipitates out of the atmosphere. Acid Rain is more accurately termed acid deposition. There are two types

More information

SELECTION GUIDE Appearance Sensing distance Operation Mode Connector Shape example (M8) Outer diameter (Ferrous material only) Wiring Output Output no

SELECTION GUIDE Appearance Sensing distance Operation Mode Connector Shape example (M8) Outer diameter (Ferrous material only) Wiring Output Output no Stainless Steel Sensing Face Proximity Switch Model FL7S The FL7S is a proximity switch having a stainless steel sensing face and housing, and is specially designed for welding applications on the automobile

More information

The Reliability Study of the Statistical Method on Insulator Dimensioning of (U)HVDC Lines with Regard to Pollution Conditions

The Reliability Study of the Statistical Method on Insulator Dimensioning of (U)HVDC Lines with Regard to Pollution Conditions 1 The Reliability Study of the Statistical Method on Insulator Dimensioning of (U)HVDC Lines with Regard to Pollution Conditions Ying Long 1, Yan Xiao 1, Zhiyi Su 2, Dong Wu 3, Urban Astrom 3 Abstract--The

More information

THE. Where are VOCs regulated?

THE. Where are VOCs regulated? THE In markets subject to volatile organic compound (VOC) regulations, single-ply roof membrane manufacturers supply alternative materials for solvent-based adhesives and primers. Among the VOC regulation-compliant

More information

Decomposition studies of no-clean solder flux systems in connection with corrosion reliability of electronics

Decomposition studies of no-clean solder flux systems in connection with corrosion reliability of electronics Downloaded from orbit.dtu.dk on: Feb 06, 2018 Decomposition studies of no-clean solder flux systems in connection with corrosion reliability of electronics Gudla, Helene Virginie Conseil; Jellesen, Morten

More information

Deterioration Control of Concrete Structures by Surface Coating Methods

Deterioration Control of Concrete Structures by Surface Coating Methods Deterioration Control of Concrete Structures by Surface Methods Takayuki Sato 1 1 Dai Nippon Toryo Co., Ltd., Japan * postal-mailing address; 878 Aza Nishinomon Mitsubuchi, Aichi-Pref., Japan 485-8516

More information

An XPS and Atomic Force Microscopy Study of the Micro-Wetting Behavior of Water on Pure Chromium* 1

An XPS and Atomic Force Microscopy Study of the Micro-Wetting Behavior of Water on Pure Chromium* 1 Materials Transactions, Vol. 44, No. 3 (2003) pp. 389 to 395 #2003 The Japan Institute of Metals An XPS and Atomic Force Microscopy Study of the Micro-Wetting Behavior of Water on Pure Chromium* 1 Rongguang

More information

Resin impregnated paper bushings. Product information

Resin impregnated paper bushings. Product information Resin impregnated paper bushings Product information This document must not be copied without our written permission, and the contents thereof must not be imparted to a third party nor be used for any

More information

PV module durability testing under high voltage biased damp heat conditions

PV module durability testing under high voltage biased damp heat conditions Available online at www.sciencedirect.com Energy Procedia 8 (2011) 6 384 389 1 5 SiliconPV: 17-20 April 2011, Freiburg, Germany PV module durability testing under high voltage biased damp heat conditions

More information

PV Lifetime Modeling an Example: PID ensuring 25 years of service life

PV Lifetime Modeling an Example: PID ensuring 25 years of service life PV Lifetime Modeling an Example: PID ensuring 25 years of service life PV Lifetime Modeling Workshop, Apr 7 th, 2015, Orlando, Florida Max B. Koentopp, Christian Taubitz, Matthias Schütze, Marcel Kröber

More information

CENTRIA The Coatings Authority

CENTRIA The Coatings Authority CENTRIA The Coatings Authority CENTRIA s Versacor Ultra Coating Systems are an innovative approach to metal coatings that offers a long-term sustainable building envelope solution and superior resistance

More information

Argon Plasma Sustained in Different Discharge Configurations

Argon Plasma Sustained in Different Discharge Configurations WDS'1 Proceedings of Contributed Papers, Part II, 76 8, 21. ISBN 978-8-7378-14-8 MATFYZPRESS Argon Plasma Sustained in Different Discharge Configurations L. Schmiedt, V. Hrachová Charles University Prague,

More information

Accelerated UV-Aging of EVA-based PV Encapsulants and Correlation with Outdoor Exposure of PV Modules

Accelerated UV-Aging of EVA-based PV Encapsulants and Correlation with Outdoor Exposure of PV Modules Accelerated UV-Aging of EVA-based PV Encapsulants and Correlation with Outdoor Exposure of PV Modules Charles G. Reid, Jayesh G. Bokria, and Joseph T. Woods Specialized Technology Resources, Inc. (STR

More information

Impact of Water Content on the Electrical Behavior of Epoxy Insulators

Impact of Water Content on the Electrical Behavior of Epoxy Insulators Impact of Water Content on the Electrical Behavior of Epoxy Insulators E. Mboungou, C. Mavon, J.-M. Friedt, C. Bergeon and M. Fromm Laboratoire de Microanalyses Nucléaires Alain Chambaudet (LMN-AC), UMR-CEA

More information

E. Mboungou, C. Mavon, J.-M. Friedt, C. Bergeon and M. Fromm

E. Mboungou, C. Mavon, J.-M. Friedt, C. Bergeon and M. Fromm Impact of Water Content on the Electrical Behavior of Epoxy Insulators E. Mboungou, C. Mavon, J.-M. Friedt, C. Bergeon and M. Fromm Laboratoire de Microanalyses Nucléaires Alain Chambaudet (LMN-AC), UMR-CEA

More information

RS Composite Utility Pole Inspection and Maintenance Guide

RS Composite Utility Pole Inspection and Maintenance Guide RS Composite Utility Pole Inspection and Maintenance Guide Project: Project Code: Pole Inspection Review N/A Rev. Description Date Performed By A RS Composite Utility Pole Inspection and Maintenance Guide

More information

Polymer Station Post Insulators for 69 to 345 kv Applications

Polymer Station Post Insulators for 69 to 345 kv Applications CATALOG 143 Polymer for 69 to 34 kv Applications NGK-Locke Polymer Insulators, Inc. Virginia Beach, Virginia, U.S.A. TABLE of CONTENTS Polymer... 1 Application Guidelines for Polymer Station Posts (SP)...

More information

SECTION EXTERIOR INSULATION AND FINISH SYSTEMS

SECTION EXTERIOR INSULATION AND FINISH SYSTEMS PART 1 - GENERAL 1.1 DESCRIPTION SECTION 07 24 00 1. Use this section only for NCA projects. 2. Detail wall section, base edge, expansion and control joint conditions for each system. Show locations of

More information

Study of Pre-polluting Methods on Artificial Icing Flashover Characteristics of Composite Insulators

Study of Pre-polluting Methods on Artificial Icing Flashover Characteristics of Composite Insulators IWAIS XIII, Andermatt, September 8 to 11, 2009 Study of Pre-polluting Methods on Artificial Icing Flashover Characteristics of Composite Insulators Lichun Shu 1, Xiaolin Li 2, Xingliang Jiang 1, Jianlin

More information

SP3S-AQ2-01 AIR QUALITY SENSOR S March, 2004

SP3S-AQ2-01 AIR QUALITY SENSOR S March, 2004 SP3S-AQ2-01 SPECIFICATIONS MODEL: TYPE: SPECIFICATION No. DATE OF ISSUE SPECIFICATIONS FOR: SP3S-AQ2-01 AIR QUALITY SENSOR S-0403-03 18 March, 2004 Dimensions 0.7 Status Name Date Original Junko Yanagitani

More information

Topview 5630 Red SMD LED

Topview 5630 Red SMD LED Topview 5630 Red SMD LED 1. Features - Chip High-Luminosity SMD LED - 5.6 x 3.0 x 0.9 mm (L x W x H), 4-Pin, Small Size Surface Mount Type - Wide Viewing Angle - Long Operating Life - MSL 3 2. Applications

More information

Conductor Shield A combination of semi-conducting tape and extruded thermosetting semi-conducting material meeting UL 1309, IEEE 1580 and UL1072.

Conductor Shield A combination of semi-conducting tape and extruded thermosetting semi-conducting material meeting UL 1309, IEEE 1580 and UL1072. 37-105VFD MMV-VFD Power Cable Three : kv - 15kV 133% Level Rated 90 C s (3) Soft annealed flexible stranded tinned copper per IEEE 150 Table 11. Extruded thermosetting 90 C Ethylene Propylene Rubber (EPR),

More information

ANSI/IEEE Standard C57.12"Standard Guide for Loading Mineral Oil Insulated Transformers"

ANSI/IEEE Standard C57.12Standard Guide for Loading Mineral Oil Insulated Transformers References: ANSI/IEEE Standard C57.12"Standard Guide for Loading Mineral Oil Insulated Transformers" IEEE Project P1276 "IEEE Guide for the Application of High Temperature Insulation Materials in Liquid

More information

PHOTOVOLTAIC SOLAR ENERGY POLYCRYSTALLINE MODULES - SI-ESF-M-BIPV-SM-P125-36

PHOTOVOLTAIC SOLAR ENERGY POLYCRYSTALLINE MODULES - SI-ESF-M-BIPV-SM-P125-36 Solar Innova uses the latest materials to manufacture photovoltaic modules. Our modules are ideal for any application that uses the photoelectric effect as a clean energy source because of its minimal

More information

Alternative Methods of Yttria Deposition For Semiconductor Applications. Rajan Bamola Paul Robinson

Alternative Methods of Yttria Deposition For Semiconductor Applications. Rajan Bamola Paul Robinson Alternative Methods of Yttria Deposition For Semiconductor Applications Rajan Bamola Paul Robinson Origin of Productivity Losses in Etch Process Aggressive corrosive/erosive plasma used for etch Corrosion/erosion

More information

MARORA A Plasma Selective-oxidation Apparatus for Metal-gate Devices

MARORA A Plasma Selective-oxidation Apparatus for Metal-gate Devices Hitachi Review Vol. 57 (2008), No. 3 127 MARORA A Plasma Selective-oxidation Apparatus for Metal-gate Devices Tadashi Terasaki Masayuki Tomita Katsuhiko Yamamoto Unryu Ogawa, Dr. Eng. Yoshiki Yonamoto,

More information

Will your product last? Put it to the test.

Will your product last? Put it to the test. Will your product last? Put it to the test. With your reputation on the line, why risk failure when you can have confidence that your products will live up to your claims? As the global leader in weathering

More information

Substation Bus Design: Current Methods Compared with Field Results

Substation Bus Design: Current Methods Compared with Field Results Electrical Transmission and Substation Structures Conference 2009 ASCE 143 Substation Bus Design: Current Methods Compared with Field Results Keith Malmedal Ph.D. P.E. P.Eng. 1 and John Wendelburg P.E.

More information

Section ARMORED MEDIUM VOLTAGE CABLES SHIELDED 3 CONDUCTOR POWER CABLE - INTERLOCKED ARMOR

Section ARMORED MEDIUM VOLTAGE CABLES SHIELDED 3 CONDUCTOR POWER CABLE - INTERLOCKED ARMOR PART 1 - GENERAL Section 26 05 15 SHIELDED 3 CONDUCTOR POWER CABLE - INTERLOCKED ARMOR 1.1 Cable shall be 15 kv, shielded, three conductor with ground, stranded copper, with continuously welded and corrugated

More information

Frequently Asked Questions (FAQ) about Epoxy-Coated Reinforcing Bars

Frequently Asked Questions (FAQ) about Epoxy-Coated Reinforcing Bars 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Engineering Technical Note ETN???? Frequently Asked Questions (FAQ) about Epoxy-Coated Reinforcing Bars Introduction CRSI routinely receives

More information

Silicone Dielectric Fluids Fredi Jakob, Karl Jakob, Nicholas Perjanik Analytical ChemTech International, Inc.

Silicone Dielectric Fluids Fredi Jakob, Karl Jakob, Nicholas Perjanik Analytical ChemTech International, Inc. Silicone Dielectric Fluids Fredi Jakob, Karl Jakob, Nicholas Perjanik Analytical ChemTech International, Inc. I. Introduction Mineral oil based dielectric fluids have been used more extensively than other

More information

Supporting Information

Supporting Information Supporting Information Uncovering the role of oxygen atom transfer in Ru-based catalytic water oxidation Dooshaye Moonshiram, 1,2 Yuliana Pineda-Galvan, 1 Darren Erdman, 1 Mark Palenik, 3, Ruifa Zong,

More information

Porcelain Insulator Performance under Different Condition of Installation around Aligarh

Porcelain Insulator Performance under Different Condition of Installation around Aligarh Porcelain Insulator Performance under Different Condition of Installation around Aligarh Asfar Ali Khan and Ekram Husain Abstract Modern Society is strongly dependent on a reliable power supply. The availability

More information

Top tipsfor getting. UV curing. process. the best from your. info 1/11

Top tipsfor getting. UV curing. process. the best from your. info 1/11 Top tipsfor getting the best from your UV curing process info 1/11 In these tips, the term adhesive also covers coatings, encapsulants, potting compounds, temporary masking materials and form-in-place

More information

Atomic Oxygen-Resistant, Static-Dissipative, Pinhole-Free Coatings for Spacecraft

Atomic Oxygen-Resistant, Static-Dissipative, Pinhole-Free Coatings for Spacecraft Physical Sciences Inc. VG10-109 Atomic Oxygen-Resistant, Static-Dissipative, Pinhole-Free Coatings for Spacecraft Michelle T. Schulberg, Robert H. Krech, Frederick S. Lauten Physical Sciences Inc. Roy

More information

In-Process Monitoring and Adaptive Control in Micro Welding with a Single-Mode Fiber Laser.

In-Process Monitoring and Adaptive Control in Micro Welding with a Single-Mode Fiber Laser. Title Author(s) In-Process Monitoring and Adaptive Control in Micro Welding with a Single-Mode Fiber Laser KAWAHITO, Yousuke; KATAYAMA, Seiji Citation Transactions of JWRI. 38(2) P.5-P.11 Issue Date 2009-12

More information

Dow Corning WL-5150 Photodefinable Spin-On Silicone

Dow Corning WL-5150 Photodefinable Spin-On Silicone Dow Corning WL-515 Photodefinable Spin-On Silicone Properties and Processing Procedures Introduction Dow Corning WL-515 is a silicone formulation which can be photopatterned and cured using standard microelectronics

More information

THERMAL IMAGE, PARTIAL DISCHARGE AND LEAKAGE CURRENT CORRELATION OF CERAMIC INSULATOR UNDER DIFFERENT CONTAMINATION LEVEL

THERMAL IMAGE, PARTIAL DISCHARGE AND LEAKAGE CURRENT CORRELATION OF CERAMIC INSULATOR UNDER DIFFERENT CONTAMINATION LEVEL THERMAL IMAGE, PARTIAL DISCHARGE AND LEAKAGE CURRENT CORRELATION OF CERAMIC INSULATOR UNDER DIFFERENT CONTAMINATION LEVEL Darwison 1.3, Syukri Arief 3, Hairul Abral 2, Ariadi Hazmi 1, M. H. Ahmad 4 and

More information

REVIEW OF LASER PLASTIC WELDING PROCESS

REVIEW OF LASER PLASTIC WELDING PROCESS REVIEW OF LASER PLASTIC WELDING PROCESS Kalpesh More 1, Rushikesh Aher 2, Makrand Bharaskar 3 1,2,3 Mechanical, Sandip Institute Technology and Research Centre/Pune University, (India) ABSTRACT There are

More information

Corrosion Rate Measurement on C-Steel

Corrosion Rate Measurement on C-Steel Measurements of corrosion rate on Carbon-steel using Electrochemical (potentiodynamic Polarization, EIS etc.) technique. Corrosion Rate Measurement on C-Steel Abdullah Al Ashraf 1. Introduction: The degradation

More information

Thermal Recovery Characteristics of a CO 2 Mixture Gas Circuit Breaker

Thermal Recovery Characteristics of a CO 2 Mixture Gas Circuit Breaker J Electr Eng Technol.2016; 11(?): 1921-718 http://dx.doi.org/10.5370/jeet.2016.11.3.1921 ISSN(Print) 1975-0102 ISSN(Online) 2093-7423 Thermal Recovery Characteristics of a CO 2 Mixture Gas Circuit Breaker

More information

Growth Of TiO 2 Films By RF Magnetron Sputtering Studies On The Structural And Optical Properties

Growth Of TiO 2 Films By RF Magnetron Sputtering Studies On The Structural And Optical Properties Journal of Multidisciplinary Engineering Science and Technology (JMEST) Growth Of TiO 2 Films By RF Magnetron Sputtering Studies On The Structural And Optical Properties Ahmed K. Abbas 1, Mohammed K. Khalaf

More information