Minimum grade (%) Velocity at full flow (m s 1 )

Size: px
Start display at page:

Download "Minimum grade (%) Velocity at full flow (m s 1 )"

Transcription

1 1.6 Pipes Effluent can be conveyed by channels or pipes under gravity or in dedicated pipelines under pressure. If pipes are used, pressure rating, water-hammer and excessive friction losses must be considered during the design stage, and the deposition of entrained materials must be avoided. Plumatella repens (a bryozoan animal) and algae are biological agents that can build up on pipe walls and impede flow, and other organisms can attack pipe material, particularly concrete. Struvite (magnesium ammonium phosphate) is a crystalline chemical compound which can also constrict pipelines. Gravity conveyance in pipes The choice of pipes, often with grated entries, as opposed to surface channels or drains, to carry effluent needs to be considered in the light of each individual site and situation. The propensity for blockages in gravity pipes needs to be considered, along with the associated restricted access and OH&S issues. Reinforced concrete, PVC (polyvinylchloride) or HDPE (high-density polyethylene) pipes are commonly used for gravity conveyance, and a host of recycled plastic products are also used. PVC is more common, but HDPE pipes can be welded on site and are resilient and easily installed. Concrete and recycled plastic pipelines, though less common, depend on price and contractor preference. The principal consideration for gravity conveyance is the presence of solids in the liquid. Tables 1 and 2 give recommended grade requirements of pipelines with and without solids in the effluent stream. Ideally, solids should be removed before pipeline conveyance. At least a threefold increase in velocity is required for satisfactory gravity discharge in a pipeline conveying solids relative to effluent without solids. The minimum pipe gradient for conveying effluent with solids therefore needs to be increased at least fifteen-fold relative to solids-free effluent. The minimum recommended pipe diameter for gravity conveyance of raw effluent on a farm is 100 mm based on operating experience. This is dictated not by hydraulics, but by the propensity for blockages. Sewer-class pipes should be used rather than stormwater-class pipes given the need for thicker walls and more resilience under impact. Table 1. Minimum grades for gravity pipe drains conveying treated pond effluent. Inside diameter (mm) Minimum grade (%) Velocity at full flow (m s 1 ) Table 2. Minimum grades for gravity pipe drains conveying raw effluent from yards or sumps. Inside diameter (mm) Minimum grade (%) Velocity at full flow (m s 1 ) The data in Tables 1 and 2 are based on municipal effluent practice. Their successful application to dairy effluent has been demonstrated over many years. Wedel (2000) has, however, determined more appropriate critical velocities for control of scour and deposition of sand-laden manure, confirming the need for transmission velocities Effluent and Manure Management Database for the Australian Dairy Industry page 25

2 exceeding 1 m s 1 to avoid deposition. Obviously, particle size is the major control, and the faster the passage of effluent, the larger the particle conveyed. To avoid the transport of sand, gravity removal is essential before diversion to a sump or storage. Blockages are common in gravity drainage pipes, and the abovementioned gradients are minimum values only. The effectiveness of pipes for conveyance of effluent is dictated by the effectiveness of grates and mesh or sedimentation sumps for removing entrained solids. Inspection pits should be installed at discrete intervals in any gravity drainage pipeline. Recommended spacings vary with diameter, but 20 m is common. These pits allow for venting and access for cleaning. Common practice is to use pits at any change of grade or direction, although T-junctions can be used to facilitate access as well. Pressurised conveyance Pipes are manufactured in a range of pressure classes, expressed in terms of a PN rating (nominal pressure rating at 20 C). Table 3 details the common pipe classes for rural applications. The choice of design pressure needs to consider the impact of increased temperature, which will reduce the pressure rating for PVC and HDPE pipes. In addition, an allowance must be made for water-hammer. In the absence of a detailed investigation, it is prudent to opt for an increase in pressure class to allow for high-risk situations where high-pressure pumps stop and start without surge protection. Example PN 4.5 (Class 4.5) pipe has a pressure rating of 450 kpa. Water-hammer (without surge protection) must be allowed for when you are selecting pipes which will be subject to rapid opening and closing of valves or starting and stopping of pumps. A hydraulic system requiring 400 kpa to be carried by the pipeline would require a PN 6 pipe a pipe with a pressure rating of 600 kpa to allow for water-hammer. This is based on experience and conservative practice. Table 3. Pipe classes. Imperial Class A 150 ft head = 65 psi Class B 200 ft head = 87 psi Class C 300 ft head = 135 psi Class D 400 ft head = 175 psi Metric PN 4.5 (Class 4.5) = 4.5 atmospheres = 450 kpa = 45 m head PN 6 (Class 6) = 6 atmospheres = 600 kpa = 60 m head PN 9 (Class 9) = 9 atmospheres = 900 kpa = 90 m head PN 12 (Class 12) = 12 atmospheres = 1200 kpa = 120 m head Table 3 is provided to assist in conversion of Imperial to metric units. It is still common to find pumps, pipes and pressure gauges marked in Imperial units, because the US irrigation market is dominant, and many contractors and farmers retain the old units. Some contractors have a personal preference for particular types of pipe, and as long as they have no pecuniary interest, their preferences should be catered for. If small-diameter pipelines are to be used, it is wise to be able to flush the line with water. The life expectancy of PVC and HDPE pressure pipes is not really dictated by the corrosive nature of effluent, but reinforced concrete pipes react to sulphuric acid. Over time detritus builds up on pipe walls, causing friction losses, and sometimes poor bedding conditions contribute to abrasion of external walls. Poor bedding can also lead to pipe collapse and leaking at joints. Effluent and Manure Management Database for the Australian Dairy Industry page 26

3 Types of pipe and fittings Table 4 compares the properties of HDPE and PVC pipes. Although not commonly used for effluent conveyance, many other types of pressure pipe are available, including: galvanised iron cast iron ductile iron recycled plastic aluminium concrete. Effluent can be corrosive when in contact with metallic or concrete pipes. If effluent contains sulphurous compounds from soil or cattle feed, corrosion of concrete can be accelerated. Concrete with a structural strength of 30 MPa should be used for pipes and hydraulic structures. The minimum reinforcement cover should not be less than 30 mm. Sulphate-resistant cement is recommended, and all exposed starter bars must be galvanised. Steel, cast iron and ductile iron pipes should be protected from corrosion. Pipe fittings are commonly made in the same material as pipes. The mixing of different types of pipe and fittings is not recommended, owing to different rates of expansion and contraction and dimensional intolerances. Energy losses in fittings are due to frictional resistance, and these must be accounted for in any hydraulic analysis. The fittings not only dissipate energy, but also enable the build-up of debris, which will throttle flow. Ideally, any fitting or pipe join should avoid a sharp edge. The use of external fittings avoids internal obstructions. Table 4. Comparison of the properties of pipes. Property Polyethylene (HDPE) Polyvinylchloride (PVC) Flow characteristics Weight Available lengths Corrosion Flexibility Effect of temperature on strength Installation Impact resistance Sunlight Life expectancy Cost equivalent Good Light Up to 300 m No Yes Sensitive Simple Fair Can withstand 50 years 1 unit Good Light 6 m No Partially Sensitive Simple Fair Requires protection 50 years 1.5 to 2 units Pipe cover, alignment and protection Pipelines should not be located above ground where human, vehicle or animal traffic is encountered. Provide at least 300 mm cover for pipes in trenches. The larger the pipe and greater the traffic load, the greater the cover required. The following are recommended minimum installation depths for Australian farming practice, but it is wise to ensure that Australian Standards are adhered to for specific types and pressure classes of pipe: open grazing country 300 mm garden 300 mm roads 400 mm cultivated ground 500 mm. Effluent and Manure Management Database for the Australian Dairy Industry page 27

4 Take care with the transportation, handling and installation of pipes, and follow manufacturers laying procedures, particularly bedding specifications. Much greater care is required with the installation of gravity pipelines than with pressure lines, as these need to be installed at grade and cannot afford to settle. Manufacturers frequently recommend more conservative depths; commonly PVC is installed with 600 mm cover under sealed roads and 750 mm under unsealed roads. Under major roads carrying B- double vehicles and milk tankers, some councils require both PVC and HDPE pipes to be sleeved in steel or concrete. The relevant Australian Standards are: AS/NZS 1254:2002 PVC pipes and fittings for storm and surface water applications (Standards Australia 2002b) AS/NZS 1260:2002 PVC-U pipes and fittings for drain, waste and vent application (Standards Australia 2002a) AS/NZS 1477:2006 PVC pipes and fittings for pressure applications (Standards Australia 2006b) AS/NZS 2032:2006 Installation of PVC pipe systems (Standards Australia 2006a) AS/NZS 2033:2008 Installation of polyethylene pipe systems (Standards Australia 2008) AS Perforated plastics drainage and effluent pipe and fittings Perforated drainage pipe and associated fittings (Standards Australia 2007a) AS Perforated plastics drainage and effluent pipe and fittings Perforated effluent pipe and associated fittings for sewerage applications (Standards Australia 2007b) AS Plastics pipes and fittings for irrigation and rural applications Polyethylene rural pipe (Standards Australia 2000) Installers should seek guidance on pipe size, gradient and laying procedures from suppliers and contractors so that installation costs can be ascertained before the pipe and fittings are purchased. The cost of installation may well overshadow the cost of the pipe. If shallow rock, cracking clay or elevated water tables are present along a pipe route, very high installation costs are likely. Factors to consider with costing the installation of pipes include: constraints on availability owing to very high demand in district or region lack of competition in supply of pipes or between construction contractors quantity of pipes and reduced unit cost with increased scale weather during installation the deeper the pipe, the greater the excavation cost and the more limited the prospect for ploughing in the availability of bedding quality control for backfill water table height the amount of rock to be excavated. Of paramount importance is the need to consider an appropriate alignment. Before excavating in unfamiliar ground, call the Dial Before You Dig service to determine the type and proximity of services. In some jurisdictions a cultural heritage investigation will also be necessary. Effluent and Manure Management Database for the Australian Dairy Industry page 28

5 References Standards Australia 2000, Perforated pipes and fittings for irrigation and rural applications Polyethylene rural pipe, Australian Standard AS :2 2000, Standards Australia, Sydney. Standards Australia 2002a, PVC-U pipes and fittings for drain, waste and vent application, Australian Standard AS/NZS 1260:2002, Standards Australia, Sydney. Standards Australia 2002b, PVC pipes and fittings for storm and surface water applications, Australian Standard AS/NZS 1254:2002, Sydney, Standards Australia. Standards Australia 2006a, Installation of PVC pipe systems, Australian Standard AS/NZS 2032:2006, Standards Australia, Sydney. Standards Australia 2006b, PVC pipes and fittings for pressure applications, Australian Standard AS/NZS 1477:2006, Standards Australia, Sydney. Standards Australia 2007a, Perforated plastics drainage and effluent pipe and fittings Perforated drainage pipe and associated fittings, Australian Standard AS 2439:1 2007, Standards Australia, Sydney. Standards Australia 2007b, Perforated plastics drainage and effluent pipe and fittings Perforated effluent pipe and associated fittings for sewerage applications, Australian Standard AS :2 2007, Standards Australia, Sydney. Standards Australia 2008, Installation of polyethylene pipe systems, Australian Standard AS/NZS 2033:2008, Standards Australia, Sydney. Wedel, A.W. 2000, Hydraulic conveyance of sand-laden dairy manure in collection channels, Paper No , ASAE Annual International Meeting, Milwaukee, Wisconsin, USA, 9 12 July 2000, ASAE. Effluent and Manure Management Database for the Australian Dairy Industry page 29

Weholite LIGHTWEIGHT PIPE SYSTEM

Weholite LIGHTWEIGHT PIPE SYSTEM Weholite LIGHTWEIGHT PIPE SYSTEM The lightweight pipe that takes a heavier load Weholite pipe is large diameter, profile wall pipe made from highdensity polyethylene (HDPE) resin, which is manufactured

More information

Highway Drainage 1- Storm Frequency and Runoff 1.1- Runoff Determination

Highway Drainage 1- Storm Frequency and Runoff 1.1- Runoff Determination Highway Drainage Proper drainage is a very important consideration in design of a highway. Inadequate drainage facilities can lead to premature deterioration of the highway and the development of adverse

More information

A reliable solution for ditching, underpassing and rainwater drainage

A reliable solution for ditching, underpassing and rainwater drainage PIPES AND CHAMBERS CULVERT PIPES A reliable solution for ditching, underpassing and rainwater drainage Culvert pipes are used to convey drain pipe water or rainwater under the ground. The smallest (110

More information

SPECIFICATION FOR PIPE CULVERT CONSTRUCTION

SPECIFICATION FOR PIPE CULVERT CONSTRUCTION SPECIFICATION FOR PIPE CULVERT CONSTRUCTION 1. SCOPE Pipe culverts shall be constructed in accordance with this specification and in conformity with the lines, levels and cross-sections shown on the drawings.

More information

PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017

PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017 SECTION 02630 - STORM DRAINAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Installation Guide BLUE904 PEX MUNICIPAL WATER SERVICE TUBING. We Build Tough Products for Tough Environments

Installation Guide BLUE904 PEX MUNICIPAL WATER SERVICE TUBING. We Build Tough Products for Tough Environments Installation Guide BLUE904 PEX MUNICIPAL WATER SERVICE TUBING W A T E R S E R V I C E T U B I N G We Build Tough Products for Tough Environments Blue904 Installation Guide 1 TABLE OF CONTENTS Introduction...................................2

More information

Pipe Material Selection Handbook For Water Supply And Sewerage

Pipe Material Selection Handbook For Water Supply And Sewerage Pipe Material Selection Handbook For Water Supply And Sewerage The following sewer system design manual discusses, in detail, how to design a from ground water or from surface storm water entering through

More information

Module 7: Hydraulic Design of Sewers and Storm Water Drains. Lecture 7: Hydraulic Design of Sewers and Storm Water Drains

Module 7: Hydraulic Design of Sewers and Storm Water Drains. Lecture 7: Hydraulic Design of Sewers and Storm Water Drains Module 7: Hydraulic Design of Sewers and Storm Water Drains Lecture 7: Hydraulic Design of Sewers and Storm Water Drains 7.0 HYDRAULIC DESIGN OF SEWERS AND STORM WATER DRAINS 7.1 General Consideration

More information

Supplementary Manual to Water Services

Supplementary Manual to Water Services Supplementary Manual to Water Services VERSION CONTROL Issue Date Version Issue Issued To Prepared By Reviewed By 27/02/15 0 1 General B Griffiths D Wharton 20/08/15 1 2 General B Griffiths D Wharton 08/06/16

More information

SECTION WASTEWATER FORCE MAINS

SECTION WASTEWATER FORCE MAINS SECTION 02732 WASTEWATER FORCE MAINS PART - GENERAL 1.01 GENERAL: A. This section includes the general requirements for design and installation of force main systems serving wastewater lift stations. B.

More information

PART 3 - STANDARDS FOR SEWERAGE FACILITIES DESIGN OF STORM SEWERS

PART 3 - STANDARDS FOR SEWERAGE FACILITIES DESIGN OF STORM SEWERS PART 3 - STANDARDS FOR SEWERAGE FACILITIES 3.3 - DESIGN OF STORM SEWERS 3.301 Design of Storm Sewers A. General Information B. Investigations and Surveys C. Special Projects 3.302 Design Criteria for Storm

More information

DESIGN OF SEWER SYSTEMS

DESIGN OF SEWER SYSTEMS Wastewater Engineering (MSc program) DESIGN OF SEWER SYSTEMS Prepared by Dr.Khaled Zaher Assistant Professor, Public Works Engineering Department, Faculty of Engineering, Cairo University 1. Sewer Materials

More information

Irrigation Rehabilitation Program Design and Construction Standards

Irrigation Rehabilitation Program Design and Construction Standards Irrigation Rehabilitation Program Design and Construction Standards Prepared by the IRP Standards Review Committee For Alberta Agriculture and Rural Development, Irrigation Secretariat April 26, 2010 Adopted

More information

SECTION HORIZONTAL DIRECTIONAL DRILLING

SECTION HORIZONTAL DIRECTIONAL DRILLING SECTION 330532- HORIZONTAL DIRECTIONAL DRILLING PART 1 - GENERAL 1.1 DESCRIPTION A. Furnish all labor, materials, tools, and equipment required to install pipes below the outer perimeter prison fence using

More information

A. Gravity-Flow, Nonpressure, Drainage-Piping Pressure Rating: 10-foot head of water (30 kpa).

A. Gravity-Flow, Nonpressure, Drainage-Piping Pressure Rating: 10-foot head of water (30 kpa). SECTION 221313 - FACILITY SANITARY SEWERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION STORM UTILITY DRAINAGE PIPING PART 1 - GENERAL 1.1 SUMMARY 1.2 SUBMITTALS 1.3 PROJECT CONDITIONS

SECTION STORM UTILITY DRAINAGE PIPING PART 1 - GENERAL 1.1 SUMMARY 1.2 SUBMITTALS 1.3 PROJECT CONDITIONS SECTION 334100 - STORM UTILITY DRAINAGE PIPING PART 1 - GENERAL 1.1 SUMMARY Section Includes: 1. Pipe and fittings. 2. Drain Basin. 3. De-chlorination tablet feeder. 4. Non-pressure transition couplings.

More information

Tough pipe for a tough environment

Tough pipe for a tough environment Sanitary Sewer Pipe Tough pipe for a tough environment SaniTite Sanitary Sewer Pipe delivers the features that engineers, contractors and municipalities demand durability, performance, handling, toughness

More information

A. This Section includes gravity-flow, nonpressure storm drainage outside the building, with the following components:

A. This Section includes gravity-flow, nonpressure storm drainage outside the building, with the following components: SECTION 334100 - STORM UTILITY DRAINAGE PIPING PART 1 - GENERAL 1.I RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

Fabrication and Installation Table of Contents

Fabrication and Installation Table of Contents Fabrication and Installation Table of Contents HDPE AQUASHIELD PRODUCTS 2 Fabrication and Installation 2 System Fabrication 3 Aqua-Swirl Installation 4 Step 1 Excavation and Bedding 4 Step 2 Pipe Connection

More information

SECTION FACILITY SANITARY SEWERS

SECTION FACILITY SANITARY SEWERS SECTION 22 13 13 FACILITY SANITARY SEWERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION CS-2. TRENCH EXCAVATION CONSTRUCTION STANDARDS

SECTION CS-2. TRENCH EXCAVATION CONSTRUCTION STANDARDS SECTION CS-2. TRENCH EXCAVATION CONSTRUCTION STANDARDS CS-2-01. GENERAL: Trench excavation shall conform with the City Standard Specifications. In general a trench is defined as an excavation in which

More information

The SmartDitch System

The SmartDitch System SmartDitch The SmartDitch System The Most Versatile Channel Lining Solution for Water Flow Control Drainage Control Erosion Control Stormwater Control Irrigation Control Spill Control SmartDitch INTRODUCING

More information

Illustrated Hard Landscape Seminars - Student Notes Copyright 1995 John Heather Rev Curriculum No. GD x 1.25hrs.

Illustrated Hard Landscape Seminars - Student Notes Copyright 1995 John Heather Rev Curriculum No. GD x 1.25hrs. The Oxford College of Garden Design Illustrated Hard Landscape Seminars - Student Notes Copyright 1995 John Heather Rev. 21.01.2009 Curriculum No. GD604-2 3 x 1.25hrs This part of the seminar deals with

More information

UPDATE 3A MINIMUM REQUIREMENTS

UPDATE 3A MINIMUM REQUIREMENTS 3. STORMWATER CONTENTS SECTION PAGE LATEST UPDATE 3A MINIMUM REQUIREMENTS 3.1 July 2004 3B MEANS OF COMPLIANCE 3.1 July 2004 3.B.1 DESIGN STANDARD 3.1 October 2005 3.B.2 DISCHARGE PERMITS 3.3 July 2004

More information

GUIDANCE MEMO NO : GUIDANCE CRITERIA FOR THE SEPARATION OF WATER MAINS AND NON-POTABLE PIPELINES

GUIDANCE MEMO NO : GUIDANCE CRITERIA FOR THE SEPARATION OF WATER MAINS AND NON-POTABLE PIPELINES State of California Memorandum Department of Health Services Date: April 4, 2003 To: From: Subject: Regional and District Engineers David P. Spath, Ph.D., Chief (Original signed by Dave) Drinking Water

More information

Drainage with system SELF structural elements

Drainage with system SELF structural elements Drainage with system SELF structural elements Drainage channels, boot scrapers, yard sumps for the house, yard and garden Contents 04 ANRIN SELF structural elements Material / Application / Properties

More information

CHAPTER 6. Sanitary Sewer

CHAPTER 6. Sanitary Sewer CHAPTER 6 Sanitary Sewer A. Introduction All proposed developments, subdivisions, and buildings must have a properly designed and constructed sanitary sewer collection system. The system shall provide

More information

F. Provide at least 2 feet of vertical separation between a water line and any utility or stormdrain crossing it.

F. Provide at least 2 feet of vertical separation between a water line and any utility or stormdrain crossing it. Section 3 F. Provide at least 2 feet of vertical separation between a water line and any utility or stormdrain crossing it. 3.8 Highway Crossings The design engineer shall, prior to the design of any highway

More information

SECTION STORM SEWER COLLECTION SYSTEM

SECTION STORM SEWER COLLECTION SYSTEM SECTION 02722 STORM SEWER COLLECTION SYSTEM PART 1 GENERAL 1.01 SUMMARY A. This section addresses the installation of storm sewer collection mains and includes the acceptable products, materials, and construction

More information

SECTION HIGH DENSITY POLYETHYLENE PIPE AND FITTINGS (PRESSURE PIPE)

SECTION HIGH DENSITY POLYETHYLENE PIPE AND FITTINGS (PRESSURE PIPE) SECTION 02623 HIGH DENSITY POLYETHYLENE PIPE AND FITTINGS (PRESSURE PIPE) PART 1 - GENERAL 1.1 SCOPE OF WORK A. Furnish all labor, materials, equipment and incidentals required and install high density

More information

Charlottetown - Water & Sewer Utility Minimum Standard of Acceptability for Water, Sewer & Sprinkler Connections

Charlottetown - Water & Sewer Utility Minimum Standard of Acceptability for Water, Sewer & Sprinkler Connections Charlottetown - Water & Sewer Utility Minimum Standard of Acceptability for Water, Sewer & Sprinkler Connections At the time of application for water, sewer and/or sprinkler service the applicant shall

More information

SECTION SANITARY UTILITY SEWERAGE PIPING

SECTION SANITARY UTILITY SEWERAGE PIPING SECTION 33 31 00 SANITARY UTILITY SEWERAGE PIPING PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Sanitary sewer pipe and fittings. 2. Underground pipe markers. 3. Connection to existing manholes. 4.

More information

SECTION POLYVINYL CHLORIDE (PVC) WATERLINE

SECTION POLYVINYL CHLORIDE (PVC) WATERLINE SECTION 02632 POLYVINYL CHLORIDE (PVC) WATERLINE PART 1 - GENERAL 1.01 SCOPE OF WORK A. Furnish all labor, materials, equipment, and incidentals required, and install polyvinyl chloride (PVC) waterline,

More information

SECTION WASTEWATER FORCE MAINS

SECTION WASTEWATER FORCE MAINS SECTION 02732 WASTEWATER FORCE MAINS PART 1 GENERAL 1.01 GENERAL: A. This section includes the general requirements for design and installation of force main systems serving wastewater lift stations. B.

More information

10.0 Storm Sewer Systems

10.0 Storm Sewer Systems October 2003 Chapter 10.0, Storm Sewer Systems Page 1 10.0 Storm Sewer Systems 10.1 Introduction A storm sewer system consists of a system of inlets, pipes, manholes, junctions, cleanouts, outlets, and

More information

Sewerage Code WSA Addendum PART 4 - CONSTRUCTION

Sewerage Code WSA Addendum PART 4 - CONSTRUCTION Addendum to the Water Industry Technical Standards and National Codes of Practice DOCUMENT W2 Sewerage Code WSA 02-1999 Addendum PART 4 - CONSTRUCTION Gippsland Water Business Management System Detailed

More information

Wastewater Collection System

Wastewater Collection System WASTEWATER COLLECTION SYSTEM CE 370 1 Wastewater Collection System The function of the collection system is to collect the wastewater from residential, commercial, and industrial areas within the service

More information

SECTION PIPE INSTALLATION

SECTION PIPE INSTALLATION SECTION 02232 PIPE INSTALLATION A. General The pipe shall be Ductile Iron pipe with Tyton push-on joints and cement lined as described and manufactured in accordance with ANSI/AWWA C151/A21.51. Gaskets

More information

Employment Intensive Infrastructure Program (EIIP) in Lebanon ANNEX 2

Employment Intensive Infrastructure Program (EIIP) in Lebanon ANNEX 2 Employment Intensive Infrastructure Program (EIIP) in Lebanon ANNEX 2 PARTICULAR SPECIFICATIONS FOR THE CONSTRUCITON OF STORM WATER DRAINAGE NETWORK March 2018 BUREAU TECHNIQUE POUR LE DEVELOPPEMENT P.O.B

More information

PRODUCT SPECIFICATIONS FOR PRODUCTS AND MATERIALS. Numerical Listing

PRODUCT SPECIFICATIONS FOR PRODUCTS AND MATERIALS. Numerical Listing S FOR PRODUCTS AND MATERIALS Numerical Listing WSA PS 200 WSA PS 201 WSA PS 202 WSA PS 202S Ductile Iron Pipes (CIOD) for Pressure Applications - Water Supply and Sewerage Ductile Iron Fittings (CIOD)

More information

WASTEWATER & STORM WATER COLLECTION AND REMOVAL

WASTEWATER & STORM WATER COLLECTION AND REMOVAL CVE 471 WATER RESOURCES ENGINEERING WASTEWATER & STORM WATER COLLECTION AND REMOVAL Assist. Prof. Dr. Bertuğ Akıntuğ Civil Engineering Program Middle East Technical University Northern Cyprus Campus CVE

More information

Low Gradient Velocity Control Short Term Steep Gradient Channel Lining Medium-Long Term Outlet Control [1] Soil Treatment Permanent

Low Gradient Velocity Control Short Term Steep Gradient Channel Lining Medium-Long Term Outlet Control [1] Soil Treatment Permanent Slope Drains DRAINAGE CONTROL TECHNIQUE Low Gradient Velocity Control Short Term Steep Gradient Channel Lining Medium-Long Term Outlet Control [1] Soil Treatment Permanent [1] Slope drains can act as outlet

More information

1. B16.1 Cast Iron Pipe Flanges and Flanged Fittings, Class C 111 Rubber Gasket Joints for Ductile Iron Pressure Pipe and Fittings

1. B16.1 Cast Iron Pipe Flanges and Flanged Fittings, Class C 111 Rubber Gasket Joints for Ductile Iron Pressure Pipe and Fittings SECTION 33 34 00 SANITARY FORCE MAIN PART 1 GENERAL 1.1 SCOPE OF WORK A. This section specifies the requirements for furnishing and installing sanitary force main and appurtenances. The pipe shall be of

More information

Low Gradient Velocity Control Short Term Steep Gradient Channel Lining Medium-Long Term Outlet Control [1] Soil Treatment Permanent

Low Gradient Velocity Control Short Term Steep Gradient Channel Lining Medium-Long Term Outlet Control [1] Soil Treatment Permanent Slope Drains DRAINAGE CONTROL TECHNIQUE Low Gradient Velocity Control Short Term Steep Gradient Channel Lining Medium-Long Term Outlet Control [1] Soil Treatment Permanent [1] Slope drains can act as outlet

More information

TECHNICAL SPECIFICATION

TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION ITEM 04821 TEMPORARY VEHICLE AND EQUIPMENT FUELING AREA PART 1 - GENERAL 1.01 Description Installation of erosion and sediment control for a temporary vehicle and equipment fueling

More information

Fabric Drop Inlet Protection

Fabric Drop Inlet Protection Fabric Drop Inlet Protection SEDIMENT CONTROL TECHNIQUE Type 1 System Sheet Flow Sandy Soils Type 2 System Concentrated Flow Clayey Soils [1] Type 3 System Supplementary Trap Dispersive Soils [1] Block

More information

CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER

CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 602 MARCH 1993 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER 602.01 SCOPE 602.02 REFERENCES 602.05 MATERIALS TABLE OF CONTENTS

More information

Section 4 Service Lines

Section 4 Service Lines Section 4 Service Lines A. General 1. A service line is that portion of a sanitary sewer line that extends from the outer building wall or foundation wall to its connection with the sewer lateral at the

More information

Sag Pipe (depressed sewers, or Inverted siphons) Dr. Sataa A. Al-Bayati(10-11)

Sag Pipe (depressed sewers, or Inverted siphons) Dr. Sataa A. Al-Bayati(10-11) بسم هللا الرحمن الرحيم Sag Pipe (depressed sewers, or Inverted siphons) Dr. Sataa A. Al-Bayati(10-11) A sewer that drops below the hydraulic gradient to pass under an obstruction, such as a railroad cut,

More information

SECTION 6 STORMWATER AND LAND DRAINAGE

SECTION 6 STORMWATER AND LAND DRAINAGE SECTION 6 STORMWATER AND LAND DRAINAGE Final Version, Approved September 2003 Section 6 and Land Drainage Contents 6.1 PERFORMANCE STANDARDS... 2 6.1.1 General... 2 6.2 MEANS OF COMPLIANCE... 3 6.2.1 General...

More information

Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification:

Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: Submittal Data Sheet Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: Date Date Date introduction < APPLICATIONS > Plant Air Ventilation Valve Actuation-Control

More information

Hydrodynamic Separation Product Calculator

Hydrodynamic Separation Product Calculator Hydrodynamic Separation Product Calculator Example Project BMP #1 CDS 2015-4 Project Information Project Name Example Project Option # A Country US State Kentucky City Covington Contact Information First

More information

DUCTILE IRON PIPES AND FITTINGS DETAILED PRODUCTS SPECIFICATIONS

DUCTILE IRON PIPES AND FITTINGS DETAILED PRODUCTS SPECIFICATIONS DUCTILE IRON PIPES AND FITTINGS DETAILED PRODUCTS SPECIFICATIONS General All Materials shall be EN, ISO or equivalent standard and shall be supplied from approved manufacturers. According to the International

More information

San Antonio Water System Standard Specifications for Construction ITEM NO. 848 SANITARY SEWERS

San Antonio Water System Standard Specifications for Construction ITEM NO. 848 SANITARY SEWERS ITEM NO. 848 SANITARY SEWERS 848.1 DESCRIPTION: This item shall govern the furnishing, installation and jointing of sanitary sewer pipe of the size and type specified by the project's plans and specifications.

More information

Section 12 Hydraulics.

Section 12 Hydraulics. Design Guidelines Section 12 Hydraulics. www.canterbury.ac.nz/learningresources Standards in the Design Guidelines Suite Design Standard Guidelines Index: 01 General 02 Architecture 03 Audio Visual 04

More information

SUPPLEMENTARY SECTION: STANDARD SPECIFICATIONS PAGE 1 STORMWATER MAINS & CULVERTS MAY 2018

SUPPLEMENTARY SECTION: STANDARD SPECIFICATIONS PAGE 1 STORMWATER MAINS & CULVERTS MAY 2018 STANDARD SPECIFICATIONS PAGE 1 STORMWATER MAINS & CULVERTS MAY 2018 PART 1 - GENERAL... 2 1.1 Work Included... 2 1.2 Related Sections... 2 1.3 Reference Standards... 2 1.4 Shop Drawings... 3 1.5 Certificates...

More information

DRAINAGE SOLUTIONS SINCE 1908 NEW PRODUCT BOSS 3000 LARGE DIAMETER STEEL REINFORCED POLYETHYLENE PIPE DURABLE LIGHTWEIGHT COST-EFFECTIVE ARMTEC.

DRAINAGE SOLUTIONS SINCE 1908 NEW PRODUCT BOSS 3000 LARGE DIAMETER STEEL REINFORCED POLYETHYLENE PIPE DURABLE LIGHTWEIGHT COST-EFFECTIVE ARMTEC. DRAINAGE SOLUTIONS SINCE 1908 NEW PRODUCT BOSS 3000 LARGE DIAMETER STEEL REINFORCED POLYETHYLENE PIPE DURABLE LIGHTWEIGHT COST-EFFECTIVE ARMTEC.COM BOSS 3000 the next generation of BOSS pipe. BIGGER. STRONGER.

More information

Temporary Watercourse Crossing: Culverts

Temporary Watercourse Crossing: Culverts Temporary Watercourse Crossing: Culverts DRAINAGE CONTROL TECHNIQUE Low Gradient Velocity Control Short Term Steep Gradient Channel Lining Medium-Long Term Outlet Control Soil Treatment Permanent Symbol

More information

EFFECTIVE FEBRUARY note: drainage permit required to call for a dampproof inspection

EFFECTIVE FEBRUARY note: drainage permit required to call for a dampproof inspection EFFECTIVE FEBRUARY 2014 note: drainage permit required to call for a dampproof inspection PERMITS & INSPECTIONS 750 17th Street West Vancouver BC V7V 3T3 westvancouver.ca/permits t: 604-925-7040 f: 604-925-7234

More information

Design of Sewerage System for Jaffarpur area in Southwest New Delhi

Design of Sewerage System for Jaffarpur area in Southwest New Delhi International Journal of Civil Engineering Research. ISSN 2278-3652 Volume 5, Number 1 (2014), pp. 29-34 Research India Publications http://www.ripublication.com/ijcer.htm Design of Sewerage System for

More information

ITEM D-701 PIPE FOR STORM DRAINS AND CULVERTS

ITEM D-701 PIPE FOR STORM DRAINS AND CULVERTS ITEM D-701 PIPE FOR STORM DRAINS AND CULVERTS 701-1 DESCRIPTION 701-1.1 This item shall consist of the construction of pipe culverts, and storm drains, removal of existing storm pipes, connections to existing

More information

DRAFT. Draft Bill of Quantities. Drainage

DRAFT. Draft Bill of Quantities. Drainage Draft Bill of Quantities September 2015 STORM DRAINAGE INFORMATION Measurement notes Drawings used : WYG (80) 140 Rev T1, D-(80) 001 Rev T1, D-(80) 002 Rev T1, D-(80) 003 Rev T1 and D-(80) 004 Rev T1 All

More information

Whitepaper. Water Management in Mining.

Whitepaper. Water Management in Mining. Whitepaper Water Management in Mining www.international.polypipe.com/harnessyourh20 Use of water in mining From the recovery of mineral ores and chemical solutions, washing minerals once they have been

More information

Wastewater Collection. (Sewer Alternatives)

Wastewater Collection. (Sewer Alternatives) Wastewater Collection (Sewer Alternatives) Sewer Basics Collection and transport of wastewater from each home/building to the point where treatment occurs. Wastewater Characterization Solids Liquids Pipe

More information

Town of Cornwall Water & Sewer Utility Corporation

Town of Cornwall Water & Sewer Utility Corporation Town of Cornwall Water & Sewer Utility Corporation Minimum Standard of Acceptability for Water, Sewer & Sprinkler Connections At the time of application for water, sewer and/or sprinkler service the applicant

More information

SECTION PUBLIC WATER SERVICE CONNECTIONS

SECTION PUBLIC WATER SERVICE CONNECTIONS SECTION 33 14 14 PUBLIC WATER SERVICE CONNECTIONS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe and fittings for water service connections to small commercial, light industrial, and residential

More information

New Fulton State Hospital Energy Control Center and Services Building (ECC/SVC) Project Number: M

New Fulton State Hospital Energy Control Center and Services Building (ECC/SVC) Project Number: M SECTION 334100 - STORM UTILITY DRAINAGE PIPING PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION WASTE WATER DRAINAGE SYSTEM Excavating, Backfilling, and Compaction for Utilities Cast-in-Place Concrete.

SECTION WASTE WATER DRAINAGE SYSTEM Excavating, Backfilling, and Compaction for Utilities Cast-in-Place Concrete. SECTION 02735 WASTE WATER DRAINAGE SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 02221 - Excavating, Backfilling, and Compaction for Utilities. 2. 03300 - Cast-in-Place Concrete. 1.02 REFERENCES

More information

Review the section Preparing for work, then complete the following.

Review the section Preparing for work, then complete the following. CHAPTER 4: PLANNING THE LAYOUT FOR A RESIDENTIAL EXTERNAL SANITARY DRAINAGE SYSTEM 105 WORKSHEET 1 Student name: Enrolment year: Class code: Competency name/number: To be completed by teachers Satisfactory

More information

PERFECT PIPE THE REVOLUTION CONTINUES

PERFECT PIPE THE REVOLUTION CONTINUES PERFECT PIPE THE REVOLUTION CONTINUES www.bilcon.com.sg 02 _ A new era My name is Mr. Perfect. I am an expert in pipe construction and will guide you through the world of Technology. The revolution continues

More information

SECTION STORM DRAINAGE

SECTION STORM DRAINAGE SECTION 02720 STORM DRAINAGE PART 1 - GENERAL 1.01 WORK INCLUDED A. Trenching and other excavation. B. Ground water control. C. Pipe bedding. D. Installation of storm drains and appurtenances. E. Installation

More information

6 STORMWATER IMPROVEMENTS

6 STORMWATER IMPROVEMENTS 6 STORMWATER IMPROVEMENTS 6.01 General Requirements a. In addition to the standards contained in this, the design of stormwater systems is also governed by several ordinances and regulations. (1) Projects

More information

TRENCHLESS CONSTRUCTION (BORING, JACKING, AND TUNNELING)

TRENCHLESS CONSTRUCTION (BORING, JACKING, AND TUNNELING) PART 1 - GENERAL TRENCHLESS CONSTRUCTION (BORING, JACKING, AND TUNNELING) 1.01 SECTION INCLUDES A. Trenchless Installation of Carrier Pipe with Casing Pipe B. Trenchless Installation of Carrier Pipe without

More information

Rigid and Flexible Pipe Design, Installation and Whole of Life Cost

Rigid and Flexible Pipe Design, Installation and Whole of Life Cost Rigid and Flexible Pipe Design, Installation and Whole of Life Cost Rigid and Flexible Pipe Design, Installation and Whole of Life Cost Executive Summary Pipes are typically identified as either flexible

More information

RURAL PIPE PRODUCT CATALOGUE

RURAL PIPE PRODUCT CATALOGUE RURAL PIPE PRODUCT CATALOGUE Issue: November 2017 www.watersandfarr.co.nz 0800 923 7473 ABOUT WATERS & FARR Established in 1954, Waters & Farr is a leading New Zealand manufacturer of high performance

More information

Gasketed Sewer Pipe. Storm and Sanitary pipe for use with Gasketed Sewer Fittings.

Gasketed Sewer Pipe. Storm and Sanitary pipe for use with Gasketed Sewer Fittings. Gasketed Sewer Pipe Storm and Sanitary pipe for use with Gasketed Sewer Fittings. Gasketed Sewer Pipe Installation Royal Municipal Solutions Gasketed Sewer Pipe weighs a fraction of the weight of traditional

More information

Sewer Audit - Design Checklist Gravity sewers, sewage pumping stations and pressure sewers

Sewer Audit - Design Checklist Gravity sewers, sewage pumping stations and pressure sewers Question Relevant Clauses Design checked? Do the drawings show an appropriate revision history, and is 1.1 the design complete, checked and effectively ready for construction? 1.2 Has the whole catchment

More information

No-Dig Technology is the art and science of pipes, ducts and cables using techniques that minimizes / eliminates the need for excavation, i.e.

No-Dig Technology is the art and science of pipes, ducts and cables using techniques that minimizes / eliminates the need for excavation, i.e. No Dig Technology Introduction: No-Dig Technology is the art and science of installing, repairing or renewing underground pipes, ducts and cables using techniques that minimizes / eliminates the need for

More information

HDPE PIPE SYSTEM ACE FLOWTECH CO., LTD. GLOBAL PIPING SOLUTIONS PROVIDER!

HDPE PIPE SYSTEM ACE FLOWTECH CO., LTD. GLOBAL PIPING SOLUTIONS PROVIDER! R ACE FLOWTECH CO., LTD HDPE PIPE SYSTEM R Ace Flowtech Co., Ltd, a subsidiary of JM Quan en Group Office address: No.2, 2-1601, Rongyuan Road, Huayuan Industrial Park, Tianjin Binhai Hi- Tech Area, Tianjin

More information

Cured-in-Place Pipe (CIPP) for Pressure Pipe. Presented by: Mike Moore

Cured-in-Place Pipe (CIPP) for Pressure Pipe. Presented by: Mike Moore Cured-in-Place Pipe (CIPP) for Pressure Pipe Presented by: Mike Moore CIPP Proven Technology Introduced over 45 years ago Most used trenchless technology for the rehabilitation of gravity flow pipeline

More information

Modular Sediment Barriers (Instream)

Modular Sediment Barriers (Instream) Modular Sediment Barriers (Instream) INSTREAM PRACTICES Flow Control No Channel Flow Dry Channels Erosion Control Low Channel Flows Shallow Water Sediment Control High Channel Flows Deep Water Symbol Photo

More information

SECTION SANITARY SEWER SYSTEM

SECTION SANITARY SEWER SYSTEM SECTION 02731 SANITARY SEWER SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Sanitary sewer system including necessary accessories indicated on drawings and specified in this section. Contractor

More information

TCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II

TCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II SECTION 221313 - FACILITY SANITARY SEWERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

DuroMaxx. Steel Reinforced Polyethylene Pipe. Dur A STEEL REINFORCED POLYETHYLENE PIPE. Sanitary Irrigation Storm Sewer Detention

DuroMaxx. Steel Reinforced Polyethylene Pipe. Dur A STEEL REINFORCED POLYETHYLENE PIPE. Sanitary Irrigation Storm Sewer Detention Steel Reinforced Polyethylene Pipe Dur A STEEL REINFORCED POLYETHYLENE PIPE Sanitary Irrigation Storm Sewer Detention Key Performance Advantages The Strength of Steel. The Durability of Plastic. It s the

More information

TECHNICAL SPECIFICATION

TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION ITEM 02514 MANHOLES 1.0 GENERAL 1.1 SCOPE This section provides for construction of sewer manholes complete in place, including the furnishing and adjusting to grade of an existing

More information

TRENCHLESS CONSTRUCTION (BORING, JACKING, AND TUNNELING)

TRENCHLESS CONSTRUCTION (BORING, JACKING, AND TUNNELING) PART 1 - GENERAL TRENCHLESS CONSTRUCTION (BORING, JACKING, AND TUNNELING) 1.01 SECTION INCLUDES A. Trenchless Installation of Carrier Pipe with Casing Pipe B. Trenchless Installation of Carrier Pipe without

More information

1. C-478 Specification for Precast Reinforced Manhole Sections. 2. D-3034 Specification for Polyvinyl Chloride (PVC) Pipe.

1. C-478 Specification for Precast Reinforced Manhole Sections. 2. D-3034 Specification for Polyvinyl Chloride (PVC) Pipe. SECTION 33 30 00 - SANITARY SEWER PART 1 - GENERAL 1.1 SCOPE OF WORK A. This Section specifies the requirements for furnishing and placing sanitary sewer pipe, laterals, stubs, and appurtenances. The pipe

More information

Design, Specification and Selection of Concrete Jacking Pipes Who Decides? What Really Matters?

Design, Specification and Selection of Concrete Jacking Pipes Who Decides? What Really Matters? Design, Specification and Selection of Concrete Jacking Pipes Who Decides? What Really Matters? Author: John C. Bower, Principal, Independent Civil Solutions Pty. Ltd. Keywords: Jacking pipes, microtunnelling,

More information

CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS

CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 602 NOVEMBER 2017 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS TABLE OF CONTENTS 602.01 SCOPE 602.02 REFERENCES 602.03 DEFINITIONS

More information

Wastewater treatment for single houses. D. O Dowd

Wastewater treatment for single houses. D. O Dowd Wastewater treatment for single houses 1 * In rural settings, connection to the local authority main sewer is not always possible, so each house has its own separate wastewater treatment system for the

More information

4.4.6 Underground Detention

4.4.6 Underground Detention 4.4.6 Underground Detention Limited Application Water Quality BMP Description: Detention storage located in underground pipe systems or vaults designed to provide water quantity control through detention

More information

CHAPTER 17: STORM SEWER STANDARDS Introduction Administration Standards 17.1

CHAPTER 17: STORM SEWER STANDARDS Introduction Administration Standards 17.1 CHAPTER 17: STORM SEWER STANDARDS 17.00 Introduction 17.01 Administration 17.02 Standards 17.1 17.00 INTRODUCTION The purpose of this chapter is to provide guidance for the design and construction of storm

More information

SECTION FOUNDATION DRAINAGE

SECTION FOUNDATION DRAINAGE SECTION 33 41 13 SPEC WRITER NOTES: Use this section only for NCA projects. Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section

More information

NELSON CITY COUNCIL INFRASTRUCTURAL ASSETS SD 601 APPROVED SENIOR EXECUTIVE INFRASTRUCTURE

NELSON CITY COUNCIL INFRASTRUCTURAL ASSETS SD 601 APPROVED SENIOR EXECUTIVE INFRASTRUCTURE SENIOR EXECUTIVE INFRASTRUCTURE DATE SD 601 SENIOR EXECUTIVE INFRASTRUCTURE DATE SD 602 SENIOR EXECUTIVE INFRASTRUCTURE DATE SD 603 SENIOR EXECUTIVE INFRASTRUCTURE DATE SD 604 NOTES 1. PRE-FORMED PLASTIC

More information

6 STORMWATER IMPROVEMENTS

6 STORMWATER IMPROVEMENTS 6 STORMWATER IMPROVEMENTS 6.01 General Requirements a. In addition to the standards contained in this, the design of stormwater systems is also governed by several ordinances and regulations. (1) Projects

More information

Canada s leader of complete geosynthetic solutions. HDPE Pipe Solutions. We offer complete solutions to all your piping needs.

Canada s leader of complete geosynthetic solutions. HDPE Pipe Solutions. We offer complete solutions to all your piping needs. Canada s leader of complete geosynthetic solutions HDPE Pipe Solutions We offer complete solutions to all your piping needs. Subdrains Corrugated HDPE Drainage Tubing terrafix subdrain pipe is used for

More information

North Harris County Regional Water Authority TABLE OF CONTENTS. CONTRACT DOCUMENTS Section No. Title

North Harris County Regional Water Authority TABLE OF CONTENTS. CONTRACT DOCUMENTS Section No. Title TABLE OF CONTENTS CONTRACT DOCUMENTS 00001 Inside Title Page 00003 Table of Contents 00004 List of Drawings 00020 Invitation to Bid 00100 Instructions to Bidders 00300 Bid 00500 Agreement 00610 Construction

More information

C. Foundation stabilization for pipe and utility structures.

C. Foundation stabilization for pipe and utility structures. PART 1 - GENERAL 1.1 SECTION INCLUDES A. Excavating, backfilling, and compacting for utilities, including pipe, structures, and appurtenances. B. Control of water in trenches. C. Foundation stabilization

More information

Section 7 Design Criteria Irrigation and Drainage Facilities

Section 7 Design Criteria Irrigation and Drainage Facilities Section 7 Design Criteria Irrigation and Drainage Facilities 7.1 Background The Irrigation and Drainage system is comprised of the Coachella Branch of the All-American Canal (Coachella Canal), Protective

More information

SANITARY WASTE AND VENT PIPING

SANITARY WASTE AND VENT PIPING SECTION 15420 - SANITARY WASTE AND VENT PIPING PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information