Cavitation Effect to the Hydraulic Piston Pump Flow Pulsation Zhang Huan 1, a

Size: px
Start display at page:

Download "Cavitation Effect to the Hydraulic Piston Pump Flow Pulsation Zhang Huan 1, a"

Transcription

1 Applied Mechanics and Materials Submitted: ISSN: , Vols , pp Accepted: doi: / Online: Trans Tech Publications, Switzerland Cavitation Effect to the Hydraulic Piston Pump Flow Pulsation Zhang Huan 1, a 1 Department of Electromechanical, Chengdu Technological University, Chengdu , China a yyyhhhlll2013@126.com Key words: water hydraulics; axial piston pump; flow pulsation; cavitations; CFD Abstract: The flow pulsation is one of the main factors, which affect the performance of water hydraulic piston pump, and cavitation also has importance effect on flow pulsation. In this paper, CFD technology is used to simulate visually the porting process,which causes the flow pulsation in water hydraulic axial piston pump. As a result, the flow pulsation rates and other parameters on fluid-field corresponding to different rotary speed and different loading are obtained respectively when cavitation is considered and not, which can present theoretic references for the development of water hydraulic pump. Introduction Along with the enhancement of people s environmental protection consciousness and requirements of the sustainable development. As the key working medium of system 0f natural water, hydraulic has gradually become the research hotspot of the hydraulic industry. As the key element of hydraulic pressure system, the performance of hydraulic pump affects the performance of the whole hydraulic system directly. It can reduce the noise of hydraulic system and improve the stability of the system by reducing the pump flow and pressure pulsation of the water pressure. Because the pressure pulsation that caused by the flow pulsation will cause the vibration and noise of hydraulic system, so the flow pulsation has become one of the key indicators of pump performance. The reason is that the main cause of flow pulsation produced as follows: 1) Cylinder and piston s relative movement speed will have sin( ϖ t + α) pulse ingredients; 2) the number of drainage plunger alternate periodically. Cavitation is an extremely complex phenomenon of fluid. It has an important influence on hydraulics parameters, such as the flow pulsation of hydraulic pump. The reason why cavitation occurs is that when the liquid internal pressure is lower than the saturated vapor pressure of water, liquid will carburate to accelerate the formation of air bubbles and generate cavitation in low pressure area. Because when air bubble breaks it will produce very big pressure, the high pressure cavity that caused by air bubbles that breaks constantly in the water flow can destroy the solid surface, forming a "empty". Cavitation phenomenon is prominent and have influence on the engineering. And cavitation is complicated.both at home and abroad, cavitation is undertook a large number of studies [1-6].But the result is not satisfactory. Many problems remains to be further explored. Therefore, reducing the process of the hydraulic piston pump with flow pulsation of the flow and reduce the generation of air pockets, have big significance of reducing pressure impact and noise. By using CFD technology to the axis of water to the plunger pump with flow visualization simulization process and analysis to the location produced by flow pulsation and cavitation in the match flow process, provides the theory basis for the improving water finale plunger pump, and helps to improve the work performance. Computational modeling and calculation conditions Computational modeling. Fig.1 is a typical schematic diagram of quantitative axial plunger pump. Due to sliding boots parts have little impact on the flow pulsation, geometric model can be simplified to a certain extent, the main parameters of the geometric model of simplified geometric model is shown in Table 1. All rights reserved. No part of contents of this paper may be reproduced or transmitted in any form or by any means without the written permission of Trans Tech Publications, (ID: , Pennsylvania State University, University Park, USA-06/03/16,23:03:32)

2 Applied Mechanics and Materials Vols Fig. 1 Structure diagram of the hydraulic pistontion pump Table 1 Main parameters of the geometric model of water hydraulics axial piston pump Arguments for value Take the value Plunger number z 9 Plunger diameter d (mm) 22 Enclosed initial length l0 volume (mm) 40 Plunger distribution circle radius R (mm) 37 Match flow window inner r1 (mm) 32 Match flow window diameter r2 (mm) 42 Water inlet big end diameter d1 (mm) 32 Small water inlet end diameter d2 (mm) 16 Drain the big end diameter d3 (mm) 22 Drain the small end diameter d4 (mm) 12 Llet suction drain length (mm) 60 Valve plate thickness z1 (mm) 5 Swash plate Angle ( ) 15.8 In this paper, in the form of valve plate seal water for opening "negative", opening Angle of 1 hydraulic pump as an example for analysis. Fig. 2 Calculation model and its meshing Due to the use of CFD software, analysis of the fluid only need to consider the flow of the fluid part, only take fluid field to establish water finale to the plunger pump model. In this case by using finite volume method, the model is divided into hexahedron units, nodes, the model grid structure as shown in Fig.2. In the figure nine of the same diameter cylindrical part on the top of the waist shape tank represents the inclosed work volume in the plunger cavity of the cylinder block. Big waist shape groove represents the valve disc shaped groove on the waist. Other cavity fluid flow channel, one of the larger diameter represents the suction cavity flow, the smaller diameter represents the pressurized water chamber flow.

3 232 Frontiers of Manufacturing Science and Measuring Technology IV Calculation conditions. Due to the compressibility of water is very small, and when the bubble accounts for a relatively small volume, will have little impact on the fluid density, thus to make the following assumptions: model of fluid flow state: 1) fluid is incompressible, Newtonian fluid; 2) by calculating the youngest of Reynolds number, the model is greater than the critical Reynolds number cri (2000 ~ 3000), so we use the turbulence model[5]. Turbulent kinetic energy is:k=1.5 U 2 I 2 (1) Turbulent energy dissipation is: k ε = C µ (2) l Eq.1: U water inlet velocity; I turbulence intensity; C µ the coefficient of turbulent model; 1/10 - mixing length (inlet height). In this paper, calculation of recommended value of 0.1, 0.09, from (< ), the main characteristics of water parameters are shown in Table 2. Density ρ (kg/m 3 ) Table 2 Physical properties of water (temperature:20 ) Dynamic Viscosity Coefficient of thermal conductivity µ k (Pa s) (W/(m K)) Specific heat C v (J/(kg K)) Mobile grid In most of the flow phenomenon, the relative motion between fluid is caused by the relative motion between solid element. In CFD calculation method, the relative motion between fluid is mainly achieved through mobile grid technology. In the Anchor the water to the plunger pump model, mobile grid is made up of cylinder body and valve disc, piston and cylinder block between the solid components caused by the relative motion between fluid flow region of the grid. In the calculation, the process of plunger cavity closed working volume changed by the rotating of cylinder body, is realized by using the ASI mobile grid technology. Because grid computing process is changing constantly, we select the transient PISO algorithm when we choose algorithms, the selected parameters are shown in Table 3. Cavitation model Table 3 Algorithm with difference scheme The transient calculation method PISO The biggest iteration steps 50 Residual correction coefficient 0.1 Stress relaxation factor 0.25 The momentum equation difference scheme LUD Cavitation is phenomena of the liquid change into a gas phase that occurred in the liquid phase in certain conditions. When the liquid pressure is lower than the saturated vapor pressure, it will produce bubbles. Air bubbles in the liquid will not only hinder the flow of fluid, but also reduce the volumetric efficiency of the pump, sometimes it will lead the phenomenon such as noise, vibration and cavitation of solid surface. And it will break when bubbles go into the high pressure area again, increasing the pitting corrosion of solid parts. The analysis of this example, we suppose the water medium is constant temperature (20 ), that means without the consideration of the heat transfer of fluid in the process of cavitation phenomenon, using the transient analysis of cavitation phenomenon.

4 Applied Mechanics and Materials Vols In this cavitation model, the scalar VOF (volume of fluid) is liquid volume ratioto in volume controlling, on behalf of cavitation region and the degree of cavitation. If C represent the value of the VOF, the control volume of gas in volume ratioto is1 C.Supposing when liquid pressure is lower than the standard vaporization pressure, it will produce bubbles in the modeling. This calculation using barotropic model, P crit = Pv, P v is saturated steam pressure in the local temperature. The physical characteristics of water vapor parameters in the temperature of 20 is shown in Table 4. Table 4 Physical properties of the water vapor (temperature:20 ) Density ρ (kg/m 3 ) The calculation results Dynamic viscosity µ 6 (Pas) The speed of sound in the water C water (m/s) The speed of sound in Water vapour C vapour (m/s) The theory of approximate calculation. 1) The rate of flow pulsation The calculating formula rate of flow pulsation of odd plunger pump is formula[2] : Qmax Qmin 2 π δ = = 2tan ( ) 100% 1 ( Q 4 max + Q z min) 2 (3) In Eq.3: δ the rate of flow pulsation ; Qmax, Q min maximum, minimum flow; z number of hydraulic pump plunger. In fact, due to the number of plunger pump are greater than or equal to 3, therefore, the Eq. 3 can be simplified as: 2 π π δ = 2tan ( ) 2( ) 100% 2 4z 4z z (4) In this article the plunger pump plunger number 9, the type of hydraulic pump flow pulsation rate can be calculated by Eq.4 is 1.54%. 2) Cavitation Theoretical analysis showed that the cylinder hole plunger movement in the process of water absorption rate and water flow area is changing. Inϕ = 3π / 2 place, the plunger movement speed is the biggest. And in ϕ = 2π place, flow area is the smallest. So the two generate cavitation easily[5]. CFD calculation results In this paper, through the adoption of mobile grid on three kinds of speed and turbulence model, we use visualization simulation analysis for the flow state in the hydraulic pump of nine kinds of working conditions of the combination of three kinds of load pressure, the analytical results is shown in Fig.3 and Fig.4. The flow curve of hydraulic pump is shown in Fig.5, and the flow pulsation rate data is shown in Table 5. Analysis of results In the usual count, we don t consider the influence of the rotational speed and load pressure of the flow pulsation, and believe that the flow fluctuation frequency of each cylinder body rotation taking a turn is z. The Fig.5 shows: (1) Water finale to the plunger pump has flow pulsation; (2) Under the condition of the same revolutions, the average flow is basically a constant;

5 234 Frontiers of Manufacturing Science and Measuring Technology IV (3) The pump which rotates a circle will have 2Z (z is the number of flow fluctuation plunger) flow fluctuations. 3-a the velocity distribution of plunger from high pressure cavity into the low pressure cavity 3-b the velocity distribution of plunger from low pressure cavity into the high pressure cavity 3-c the Pressure distribution of plunger from high pressure cavity into the low pressure cavity 3-d the Pressure distribution of plunger from low pressure cavity into the high pressure cavity Fig.3 The velocity distribution and the pressure distribution of closed plunger pump vessel as regardless of the cavitation 4-a the velocity distribution of the plunger from high pressure cavity into the low pressure cavity 4-b the velocity distribution of plunger from low pressure cavity into the high pressure cavity

6 Applied Mechanics and Materials Vols c the Pressure distribution of plunger from high pressure cavity into the low pressure cavity 4-d the Pressure distribution of plunger from low pressure cavity into the high pressure cavity 4-f the cavitation distribution of plunger from 4-e the cavitation distribution of plunger from low pressure cavity into the high pressure cavity high pressure cavity into the low pressure cavity Fig.4 The velocity distribution and the Pressure distribution and the cavitation distribution of closed Plunger pump vessel as Regardless of the cavitation Rotate Speed (rpm) Fig. 5 The flow curve in condition of 15 MPa pressure and rotating speed of 1000 r/min Load (MPa) Table 5 Flow pulsation rate Qaver (L/min) Qmax (L/min) Qmin (L/min) δ (%) A B A B A B A B

7 236 Frontiers of Manufacturing Science and Measuring Technology IV Condition A: without consideration of cavitation Condition B: with consideration of cavitation It can be seen from Table 5 that not considering cavitation occurs, flow pulsation rate values are between 1.54% and 1.94%,and it is consistent with the theoretical calculation results. When considering cavitation occurs, flow pulsation rate values are between 1.52% and 2.29%, and it is widely different from the theoretical calculation results. It can be seen from figure 3 and figure 4: hydraulic pump flow form use opening "negative". When the plunger cavity closed volume are between high and low, pressure mutation will come up, causing flow fluctuation. With the impact on load pressure, rotating speed of cylinder block and cavitation, the actual conditions of hydraulic pump flow pulsation rate and the theoretical calculation results is different, that means the speed and the working pressure of the pump field have effect on the rate of flow pulsation. Summary For the same axial plunger pump, from the above results may safely draw the conclusion as follows: (1) When the speed is same, the greater is the load pressure, the greater is the flow pulsation. (2) When the load pressure is same, the higher is the speed, the smaller is the flow pulsation. This kind of phenomenon is more obvious in high pressure; (3) The pump which rotates a circle will have 2Z (z is the number of flow fluctuation plunger) flow fluctuations. (4) For the flow pulsation, when considering holes are much larger than when not considering. To sum up, it should be considered rotation speed, load and the influence of cavitation on the discharge pulse pressure when designing or improving water finale to the plunger pump. Especially when the load s pressure is high and has high speed, it should be improved through the structure and the installation position of the pump, improving water finale to the plunger pump flow and pressure characteristics, reduce or eliminate the resulting fluid noise. Acknowledgements The corresponding author of this paper is Zhang Huan. This paper is supported by Natural Science Foundation of the Education Department of Sichuan Province, China[14ZB0296]. References [1] Deng Bin, Wang Jinnuo AnWeiSheng, KeJian. Noise and influence factors analysis of hydraulic piston pump [J]. Journal of machine tools and hydraulic, 2002 (6) : [2] Xu Shengwu, plunger pump [M]. Mechanical industry publishing house, 1985 [3] Liu Donghai Huang Xiaoyun, piston diaphragm pump and the hydraulic diaphragm pump flow pulsation analysis [J]. Journal of hydraulic and pneumatic, 2012 (1 l) : [4] Xu Bing, Song Yuechao, Yang Huayong, complex export pipeline plunger pump flow pulsation test principle [J]. Journal of mechanical engineering, 2012 (22) : 13, [5] Yu Lijuan, wang, Zhang Xuecheng to plunger pump flow pulsation active control method and simulation study [J]. Journal of xi 'an jiaotong university, 2013,47 (11) : [6] Wang Xingkun, the east, hu ShangJianDong, double-acting vane pump flow field numerical simulation and characteristics analysis [J]. Journal of hydraulics and pneumatics, 2013 (5) : 23-26

8 Frontiers of Manufacturing Science and Measuring Technology IV / Cavitation Effect to the Hydraulic Piston Pump Flow Pulsation /

Impellers of low specific speed centrifugal pump based on the draughting technology

Impellers of low specific speed centrifugal pump based on the draughting technology IOP Conference Series: Earth and Environmental Science Impellers of low specific speed centrifugal pump based on the draughting technology To cite this article: C Hongxun et al 2010 IOP Conf. Ser.: Earth

More information

Numerical Simulation of the Flue Gas Desulfurization in the Sieve Tray Tower

Numerical Simulation of the Flue Gas Desulfurization in the Sieve Tray Tower 52 China Steel Technical Report, No. Numerical 28, pp.52-57, Simulation (2015) of the Flue Gas Desulfurization in the Sieve Tray Tower Numerical Simulation of the Flue Gas Desulfurization in the Sieve

More information

FLUID FLOW - PUMPS. Discharge Section. Section. Two main types of pumps: Positive Displacement pumps Centrifugal pumps.

FLUID FLOW - PUMPS. Discharge Section. Section. Two main types of pumps: Positive Displacement pumps Centrifugal pumps. FLUID FLOW - PUMPS 4 3 Control valve Suction Section Discharge Section Two main types of pumps: Positive Displacement pumps Centrifugal pumps ChE 453 - Design I FLUID FLOW - PUMP PERFORMANCE Mechanical

More information

[4163] T.E. (Mechanical) TURBO MACHINES (2008 Pattern) (Common to Mech. S/W) (Sem. - II)

[4163] T.E. (Mechanical) TURBO MACHINES (2008 Pattern) (Common to Mech. S/W) (Sem. - II) Total No. of Questions : 12] P1061 SEAT No. : [Total No. of Pages : 7 [4163] - 218 T.E. (Mechanical) TURBO MACHINES (2008 Pattern) (Common to Mech. S/W) (Sem. - II) Time : 3 Hours] [Max. Marks :100 Instructions

More information

Control of Gas Bubbles and Slag Layer in a Ladle Furnace by Electromagnetic

Control of Gas Bubbles and Slag Layer in a Ladle Furnace by Electromagnetic Control of Gas Bubbles and Slag Layer in a Ladle Furnace by Electromagnetic Stirring The demands on flow control in the ladle vary from different functions and stages in a ladle refining cycle. With the

More information

Numerical prediction research on the evaporation rate of liquid cargo tank for LNG Filling Vessel Based on Ansys

Numerical prediction research on the evaporation rate of liquid cargo tank for LNG Filling Vessel Based on Ansys 5th International Conference on Measurement, Instrumentation and Automation (ICMIA 2016) Numerical prediction research on the evaporation rate of liquid cargo tank for LNG Filling Vessel Based on Ansys

More information

The Integral Optimization Method of Oilfield Production System

The Integral Optimization Method of Oilfield Production System Advances in Petroleum Exploration and Development Vol. 13, No. 1, 17, pp. 57-6 DOI:1.3968/9418 ISSN 195-54X [Print] ISSN 195-5438 [Online] www.cscanada.net www.cscanada.org The Integral Optimization Method

More information

Stress analysis of reciprocating pump pipeline system in oil station

Stress analysis of reciprocating pump pipeline system in oil station Available online www.jocpr.com Journal of Chemical and Pharmaceutical Research, 2014, 6(7):2026-2032 Research Article ISSN : 0975-7384 CODEN(USA) : JCPRC5 Stress analysis of reciprocating pump pipeline

More information

Study of water falling film over horizontal drop shaped and inverted drop shaped tubes

Study of water falling film over horizontal drop shaped and inverted drop shaped tubes Study of water falling film over horizontal drop shaped and inverted drop shaped tubes Vipul Kumar Sharma, Nirmal Kant Singh 2 Dept. of Mechanical Engineering, GLBITM, Greater Noida, U.P, 236, India 2

More information

Thermal Management of Densely-packed EV Battery Set

Thermal Management of Densely-packed EV Battery Set EVS28 KINTEX, Korea, May 3-6, 2015 Thermal Management of Densely-packed EV Battery Set Abstract Z. Lu 1, X.Z. Meng 1, W.Y. Hu 2, L.C. Wei 3, L.Y. Zhang 1, L.W. Jin 1* 1 Building Environment and Equipment

More information

Natural Gas Transmission Pipeline Temperature Drop Calculation

Natural Gas Transmission Pipeline Temperature Drop Calculation Advances in Petroleum Exploration and Development Vol. 8, No., 14, pp. 4-8 DOI:1.3968/5798 ISSN 195-54X [Print] ISSN 195-5438 [Online] www.cscanada.net www.cscanada.org Natural Gas ransmission Pipeline

More information

Investigation of Surface Vortex Formation at Pump Intakes in PWR

Investigation of Surface Vortex Formation at Pump Intakes in PWR Investigation of Surface Vortex Formation at Pump Intakes in PWR P. Pandazis 1, A. Schaffrath 1, F. Blömeling 2 1 Gesellschaft für Anlagen- und Reaktorsicherheit (GRS) ggmbh, Munich 2 TÜV NORD SysTec GmbH

More information

Optimization of abrasive waterjet nozzle design for precision and reduced wear using compressible multiphase CFD modelling

Optimization of abrasive waterjet nozzle design for precision and reduced wear using compressible multiphase CFD modelling Optimization of abrasive waterjet nozzle design for precision and reduced wear using compressible multiphase CFD modelling C. Narayanan, D. Caviezel, D. Lakehal ASCOMP AG Technoparkstrasse 1, 8005 Zurich,

More information

CFD Analysis of Pelton Runner

CFD Analysis of Pelton Runner International Journal of Scientific and Research Publications, Volume 4, Issue 8, August 2014 1 CFD Analysis of Pelton Runner Amod Panthee *, Hari Prasad Neopane **, Bhola Thapa ** * Turbine Testing Lab,

More information

CFD/FEM Based Analysis Framework for Wind Effects on Tall Buildings in Urban Areas

CFD/FEM Based Analysis Framework for Wind Effects on Tall Buildings in Urban Areas 2017 2nd International Conference on Industrial Aerodynamics (ICIA 2017) ISBN: 978-1-60595-481-3 CFD/FEM Based Analysis Framework for Wind Effects on Tall Buildings in Urban Areas Qiao Yan, Dalong Li,

More information

Numerical Simulation of Spray Cooling Gas with High Temperature and Velocity in Compressor Inter-Stage

Numerical Simulation of Spray Cooling Gas with High Temperature and Velocity in Compressor Inter-Stage 979 A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 61, 2017 Guest Editors: Petar S Varbanov, Rongxin Su, Hon Loong Lam, Xia Liu, Jiří J Klemeš Copyright 2017, AIDIC Servizi S.r.l. ISBN 978-88-95608-51-8;

More information

Hydraulic performance of a low specific speed centrifugal pump with Spanwise-Slotted Blades

Hydraulic performance of a low specific speed centrifugal pump with Spanwise-Slotted Blades IOP Conference Series: Materials Science and Engineering OPEN ACCESS Hydraulic performance of a low specific speed centrifugal pump with Spanwise-Slotted Blades To cite this article: D X Ye et al 2013

More information

CEE 452/652. Week 12, Lecture 1 Cyclones. Dr. Dave DuBois Division of Atmospheric Sciences, Desert Research Institute

CEE 452/652. Week 12, Lecture 1 Cyclones. Dr. Dave DuBois Division of Atmospheric Sciences, Desert Research Institute CEE 452/652 Week 12, Lecture 1 Cyclones Dr. Dave DuBois Division of Atmospheric Sciences, Desert Research Institute Today s topics Today s topic: cyclones Read chapter 4 Homework on ch. 3, due Thurs. Select

More information

COMSOL Multiphysics Simulation of Flow in a Radial Flow Fixed Bed Reactor (RFBR)

COMSOL Multiphysics Simulation of Flow in a Radial Flow Fixed Bed Reactor (RFBR) COMSOL Multiphysics Simulation of Flow in a Radial Flow Fixed Bed Reactor (RFBR) Anthony G. Dixon *,1, Dominic Polcari 1, Anthony Stolo 1 and Mai Tomida 1 1 Department of Chemical Engineering, Worcester

More information

Fluidised bed for stripping sand casting process. Guido Belforte, Massimiliana Carello, Vladimir Viktorov

Fluidised bed for stripping sand casting process. Guido Belforte, Massimiliana Carello, Vladimir Viktorov Fluidised bed for stripping sand casting process Guido Belforte, Massimiliana Carello, Vladimir Viktorov Dipartimento di Meccanica - Politecnico di Torino C.so Duca degli Abruzzi, 24 10129 Torino Italy

More information

PAPER-I (Conventional)

PAPER-I (Conventional) 1. a. PAPER-I (Conventional) 10 kg of pure ice at 10 ºC is separated from 6 kg of pure water at +10 O C in an adiabatic chamber using a thin adiabatic membrane. Upon rupture of the membrane, ice and water

More information

Improving Efficiency of Submersible Pump Impeller of Mixed Flow Type by Design Modification through CFD Analysis

Improving Efficiency of Submersible Pump Impeller of Mixed Flow Type by Design Modification through CFD Analysis Improving Efficiency of Submersible Pump Impeller of Mixed Flow Type by Design Modification through CFD Analysis Naveen Nagalinga Lohar 1, Prof. S A Janawade 2. 1Department of Mechanical Engineering (M.Tech

More information

STUDY ON DESIGN AND STATIC ANALYSIS OF PISTON HEAD

STUDY ON DESIGN AND STATIC ANALYSIS OF PISTON HEAD STUDY ON DESIGN AND STATIC ANALYSIS OF PISTON HEAD Amitanand B Suralikerimath 1, Yallanagouda I Ninganagoudar 2, C.M Veerendrakumar 3 1 Student, Department of Mechanical Engineering, Basaveshwar Engineering

More information

1 Mold 4 Cavity Tube Bending Mold Design based on Moldflow

1 Mold 4 Cavity Tube Bending Mold Design based on Moldflow 1 Mold 4 Cavity Tube Bending Mold Design based on Moldflow Beijing Jiaotong University, Beijing, China, 15001046680@163.com Abstract In this paper, according to the 1 mold 2 cavity tube bending die without

More information

Pumps, Turbines, and Pipe Networks, part 2. Ch 11 Young

Pumps, Turbines, and Pipe Networks, part 2. Ch 11 Young Pumps, Turbines, and Pipe Networks, part 2 Ch 11 Young Pump and Turbine Dimensional Analysis (11.5 Young) Say we want to replace turbines on the Hoover Dam Want to have a good design Essentially impossible

More information

Design, Modeling & Analysis of a Submersible Pump and to improve the Pump Efficiency

Design, Modeling & Analysis of a Submersible Pump and to improve the Pump Efficiency Design, Modeling & Analysis of a Submersible Pump and to improve the Pump Efficiency Shyam Karanth Department of Mechanical Engineering, SDM College of Engineering and Technology, Dharwad, Karnataka, India

More information

Chemical Injection Methods for Irrigation 1

Chemical Injection Methods for Irrigation 1 CIR864 1 Dorota Z. Haman and Fedro S. Zazueta 2 Methods of Chemical Injections Chemical application through irrigation systems is called chemigation. Chemigation has been practiced for many years especially

More information

Module 9 : Sewage And Storm water Pumping Stations. Lecture 11 : Sewage And Storm water Pumping Stations

Module 9 : Sewage And Storm water Pumping Stations. Lecture 11 : Sewage And Storm water Pumping Stations 1 P age Module 9 : Sewage And Storm water Pumping Stations Lecture 11 : Sewage And Storm water Pumping Stations 2 P age 9.1 Introduction There are certain locations where it is possible to convey sewage

More information

Flow Characterization of a Piezo-Electric High Speed Valve

Flow Characterization of a Piezo-Electric High Speed Valve Flow Characterization of a Piezo-Electric High Speed Valve T. Takiya*, N. Fukuda*, M. Yaga** and M. Han*** *( Hitachi Zosen Corporation, Osaka 551-0022, Japan) ** (Department of Mechanical Systems Engineering,

More information

Control of the Convective Flow Instabilities in a Simulated Czochralski Growth System

Control of the Convective Flow Instabilities in a Simulated Czochralski Growth System Copyright 2017 Tech Science Press FDMP, vol.13, no.1, pp.1-17, 2017 Control of the Convective Flow Instabilities in a Simulated Czochralski Growth System N. Soltani 1 and S. Rahal 1 bstract: three-dimensional

More information

Research on the Trajectory of Oil Spill in Near-shore Area

Research on the Trajectory of Oil Spill in Near-shore Area International Journal of Engineering Science Invention ISSN (Online): 2319 6734, ISSN (Print): 2319 6726 Volume 4 Issue 4 April 2015 PP.68-74 Research on the Trajectory of Oil Spill in Near-shore Area

More information

Die design and process optimization of plastic gear extrusion

Die design and process optimization of plastic gear extrusion IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Die design and process optimization of plastic gear extrusion To cite this article: Lei Zhang et al 2018 IOP Conf. Ser.: Mater.

More information

Alpha Hemihydrate Gypsum Preparationed by Atmospheric Pressure Salt Solution Method Process Route Zhao Luo 1, a, Fenglan Han 2,b and Xinhua Huang 3,c

Alpha Hemihydrate Gypsum Preparationed by Atmospheric Pressure Salt Solution Method Process Route Zhao Luo 1, a, Fenglan Han 2,b and Xinhua Huang 3,c Applied Mechanics and Materials Online: 2013-06-13 ISSN: 1662-7482, Vol. 327, pp 23-27 doi:10.4028/www.scientific.net/amm.327.23 2013 Trans Tech Publications, Switzerland Alpha Hemihydrate Gypsum Preparationed

More information

THERMAL AND STRUCTURAL ANALYSIS OF CONNECTING ROD OF AN IC ENGINE

THERMAL AND STRUCTURAL ANALYSIS OF CONNECTING ROD OF AN IC ENGINE THERMAL AND STRUCTURAL ANALYSIS OF CONNECTING ROD OF AN IC ENGINE 1 Mr. Shubham Chougale 1 UG student 1 Department of Mechanical Engineering 1 TSSM BSCOER, Pune, India Abstract The connecting rod is a

More information

Screening, Definition: The unit involved is called a screen.

Screening, Definition: The unit involved is called a screen. Screening, Definition: Screening is a unit operation that separates materials in and/or on water (found in different sizes) from water and from entering water treatment facilities and mains. The unit involved

More information

Installation Guidelines for Flygt Pumps Pump Anchoring Recommendations

Installation Guidelines for Flygt Pumps Pump Anchoring Recommendations Issued: Installation Guidelines for Flygt Pumps Pump Anchoring Recommendations Introduction Proper installation and anchorage of Flygt pumps and installation accessories is critical to limiting vibration

More information

Design and Simulation of Liquid-cooling Plates for Thermal Management of EV Batteries

Design and Simulation of Liquid-cooling Plates for Thermal Management of EV Batteries EVS28 KINTEX, Korea, May 3-6, 2015 Design and Simulation of Liquid-cooling Plates for Thermal Management of EV Batteries Dai Haifeng 1,2, Sun Zechang 1, 2, Wei Xuezhe 1,2,Yang Shuqiang 2 1 Clean Automotive

More information

Chapter 5 1. Hydraulic Pumps (pp , Gorla & Khan; Wiki)

Chapter 5 1. Hydraulic Pumps (pp , Gorla & Khan; Wiki) Chapter 5 1. Hydraulic Pumps (pp. 47 90, Gorla & Khan; Wiki) 1. Two Basic Categories of Pumps Positive Displacement (PD) Pumps A positive displacement pump causes a fluid to move by trapping a fixed amount

More information

Abstract. Nomenclature. A Porosity function for momentum equations L Latent heat of melting (J/Kg) c Specific heat (J/kg-K) s Liquid fraction

Abstract. Nomenclature. A Porosity function for momentum equations L Latent heat of melting (J/Kg) c Specific heat (J/kg-K) s Liquid fraction Enthalpy Porosity Method for CFD Simulation of Natural Convection Phenomenon for Phase Change Problems in the Molten Pool and its Importance during Melting of Solids Abstract Priyanshu Goyal, Anu Dutta,

More information

Solid Circulation and Gas Bypassing in an Internally Circulating Fluidized Bed with an Orifice-Type Draft Tube

Solid Circulation and Gas Bypassing in an Internally Circulating Fluidized Bed with an Orifice-Type Draft Tube Korean J. Chem. Eng., 16(5), 618-623 (1999) Solid Circulation and Gas Bypassing in an Internally Circulating Fluidized Bed with an Orifice-Type Draft Tube Hong-Sik Ahn, Woon-Jae Lee, Sang-Done Kim and

More information

Optimization of embedded Heat Exchanger in a flat plate Integrated Collector Storage Solar Water Heater (ICSSWH), with indirect heat withdrawal.

Optimization of embedded Heat Exchanger in a flat plate Integrated Collector Storage Solar Water Heater (ICSSWH), with indirect heat withdrawal. World Renewable Energy Congress (WRECX) Editor A. Sayigh 2008 WREC. All rights reserved. 1815 Optimization of embedded Heat Exchanger in a flat plate Integrated Collector Storage Solar Water Heater (ICSSWH),

More information

CFD on Small Flow Injection of Advanced Accumulator in APWR

CFD on Small Flow Injection of Advanced Accumulator in APWR 54 CFD on Small Flow Injection of Advanced Accumulator in APWR TOMOSHIGE TAKATA TAKAFUMI OGINO TAKASHI ISHIBASHI TADASHI SHIRAISHI The advanced accumulator in the advanced pressurized-water reactor is

More information

Design and Analysis of 3D Blades for Wells Turbine

Design and Analysis of 3D Blades for Wells Turbine IJIRST International Journal for Innovative Research in Science & Technology Volume 1 Issue 11 April 2015 ISSN (online): 2349-6010 Design and Analysis of 3D Blades for Wells Turbine Shyjo Johnson Saintgits

More information

The Detection and Analysis of Reservoir Dam Crack Depth and Grouting Quality Analysis

The Detection and Analysis of Reservoir Dam Crack Depth and Grouting Quality Analysis Applied Mechanics and Materials Online: 2012-10-26 ISSN: 1662-7482, Vols. 204-208, pp 3329-3332 doi:10.4028/www.scientific.net/amm.204-208.3329 2012 Trans Tech Publications, Switzerland The Detection and

More information

Flow Induced Vibration A Review of Current Assessment Methods

Flow Induced Vibration A Review of Current Assessment Methods Flow Induced Vibration A Review of Current Assessment Methods David Fielding, Matt Straw (Norton Straw Consultants) Alex Graham, Phil Shorter (CD-adapco) Introduction Presenting a joint study into flow-induced

More information

Flow and Heat Transfer Characteristics in High Porosity Metal Foams

Flow and Heat Transfer Characteristics in High Porosity Metal Foams Proceedings of the World Congress on Mechanical, Chemical, and Material Engineering (MCM 2015) Barcelona, Spain July 20-21, 2015 Paper No. 333 Flow and Heat Transfer Characteristics in High Porosity Metal

More information

Effect of Bearing Design Parameters on the Minimum Oil Film Thickness of Hydrodynamic Journal Bearing

Effect of Bearing Design Parameters on the Minimum Oil Film Thickness of Hydrodynamic Journal Bearing Volume: 04 Issue: 08 Aug -2017 www.irjet.net p-issn: 2395-0072 Effect of Bearing Design Parameters on the Minimum Oil Film Thickness of Hydrodynamic Journal Bearing Mohammed Ali 1, S.K. Somani 2 1Department

More information

3.5.7 Flow Through Simple Dies

3.5.7 Flow Through Simple Dies 152 3 Fundamentals of Polymers isothermal spinning of a Newtonian fluid and predicted the critical draw ratio of 20.210. Below the critical draw ratio, any disturbance along the filament is dampened out

More information

Design of a Small Scale CFB Boiler Combustion Chamber for Laboratory Purposes

Design of a Small Scale CFB Boiler Combustion Chamber for Laboratory Purposes International Journal of Emerging Engineering Research and Technology Volume 3, Issue 9, September, 2015, PP 1-7 ISSN 2349-4395 (Print) & ISSN 2349-4409 (Online) Design of a Small Scale CFB Boiler Combustion

More information

Piping Vibration Risks and Integrity Assessment

Piping Vibration Risks and Integrity Assessment Piping systems are subject to vibration induced failures. To mitigate this integrity risk, a piping vibration assessment is conducted during the design phase and high risk locations are tested during operation.

More information

Simulation of Binary Mixture Droplet Evaporation using VOF Methods

Simulation of Binary Mixture Droplet Evaporation using VOF Methods Peter Keller and Christian Hasse Department of Energy Process Engineering and Chemical Engineering TU Bergakademie Freiberg Simulation of Binary Mixture using VOF Methods June 14, 2011 6 th OpenFOAM R

More information

Available online at ScienceDirect. Aquatic Procedia 3 (2015 ) International Oil Spill Response Technical Seminar

Available online at  ScienceDirect. Aquatic Procedia 3 (2015 ) International Oil Spill Response Technical Seminar Available online at www.sciencedirect.com ScienceDirect Aquatic Procedia 3 (2015 ) 50 58 International Oil Spill Response Technical Seminar Fundamental Study on a New Thin Oil-film Recovery Device Based

More information

Simulation Study Based on OpenTrack on Carrying Capacity in District of Beijing-Shanghai High-speed Railway

Simulation Study Based on OpenTrack on Carrying Capacity in District of Beijing-Shanghai High-speed Railway Applied Mechanics and Materials Online: 2014-01-16 ISSN: 1662-7482, Vols. 505-506, pp 567-570 doi:10.4028/www.scientific.net/amm.505-506.567 2014 Trans Tech Publications, Switzerland Simulation Study Based

More information

International Journal Of Scientific Research And Education Volume 3 Issue 3 Pages March-2015 ISSN (e): Website:

International Journal Of Scientific Research And Education Volume 3 Issue 3 Pages March-2015 ISSN (e): Website: International Journal Of Scientific Research And Education Volume 3 Issue 3 Pages-2969-2977 March-2015 ISSN (e): 2321-7545 Website: http://ijsae.in Experimental Analyses for NDWCT Performance Using Trickle

More information

CFD Technique for Solving Low Water Level Problem of Axial Flow Pumps

CFD Technique for Solving Low Water Level Problem of Axial Flow Pumps American Journal of Water Science and Engineering 2017; 3(3): 34-44 http://www.sciencepublishinggroup.com/j/ajwse doi: 10.11648/j.ajwse.20170303.11 ISSN: 2575-1867 (Print); ISSN: 2575-1875 (Online) CFD

More information

CYLINDRICAL VESSEL LIMIT LOAD ESTIMATION FOR OBLIQUE NOZZLE BY USING ANSYS AS ANALYSIS TOOL

CYLINDRICAL VESSEL LIMIT LOAD ESTIMATION FOR OBLIQUE NOZZLE BY USING ANSYS AS ANALYSIS TOOL CYLINDRICAL VESSEL LIMIT LOAD ESTIMATION FOR OBLIQUE NOZZLE BY USING ANSYS AS ANALYSIS TOOL 1 DILIP M PATEL, 2 Dr. BIMLESH KUMAR 1 Department of Mechanical Engineering D.N.Patel C.O.E, Shahada-420425 2

More information

NUMERICAL SIMULATION AND EXPERIMENTAL RESEARCH ON CRACK MAGNETIC FLUX LEAKAGE FIELD

NUMERICAL SIMULATION AND EXPERIMENTAL RESEARCH ON CRACK MAGNETIC FLUX LEAKAGE FIELD Proceedings of the ASME 2011 Pressure Vessels & Piping Division Conference PVP2011 July 17-21, 2011, Baltimore, Maryland, USA PVP2011-57514 NUMERICAL SIMULATION AND EXPERIMENTAL RESEARCH ON CRACK MAGNETIC

More information

CFD simulation on the turbulent mixing flow performance of the liquid-liquid ejector

CFD simulation on the turbulent mixing flow performance of the liquid-liquid ejector IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS CFD simulation on the turbulent mixing flow performance of the liquid-liquid ejector To cite this article: W Z An et al 2016 IOP

More information

An Extrusion Die with Twin Cavities for Semi-hollow Al-Profiles

An Extrusion Die with Twin Cavities for Semi-hollow Al-Profiles An Extrusion Die with Twin Cavities for Semi-hollow Al-Profiles Xuemei Huang 1,a, Rurong Deng 2,b * 1,2 Guangzhou Vocational College of Science and Technology, Guangzhou, 510550, China a Email: 41784402@qq.com,

More information

Simulation of High Pressure Die Casting (HPDC) via STAR-Cast

Simulation of High Pressure Die Casting (HPDC) via STAR-Cast Simulation of High Pressure Die Casting (HPDC) via STAR-Cast STAR Global Conf. 2012, 19-21 March, Noordwijk Romuald Laqua, Access e.v., Aachen High Pressure Die Casting: Machines and Products Common Materials:

More information

A CFD ANALYSIS OF CENTRIFUGAL PUMP TO IMPROVE DISCHARGE BY VARYING BLADE GEOMETRY

A CFD ANALYSIS OF CENTRIFUGAL PUMP TO IMPROVE DISCHARGE BY VARYING BLADE GEOMETRY A CFD ANALYSIS OF CENTRIFUGAL PUMP TO IMPROVE DISCHARGE BY VARYING BLADE GEOMETRY 1 ANJANI KUMAR SINHA, 2 A. JOHN RAJAN, 3 ERIKI ANANDA KUMAR 1,3 Senior Lecturer, Dept. of Mech. Eng., Nilai University,

More information

INDIAN REGISTER OF SHIPPING CLASSIFICATION NOTES. Type Approval of Mechanical Joints used in Piping

INDIAN REGISTER OF SHIPPING CLASSIFICATION NOTES. Type Approval of Mechanical Joints used in Piping INDIAN REGISTER OF SHIPPING CLASSIFICATION NOTES Type Approval of Mechanical Joints used in Piping January 2017 Page 2 of 16 Changes in JANUARY 2017 Version Type Approval of Mechanical Joints used in Piping

More information

Numerical Investigation of the Flow Dynamics of a Supersonic Fluid Ejector

Numerical Investigation of the Flow Dynamics of a Supersonic Fluid Ejector Proceedings of the International Conference on Heat Transfer and Fluid Flow Prague, Czech Republic, August 11-12, 2014 Paper No. 171 Numerical Investigation of the Flow Dynamics of a Supersonic Fluid Ejector

More information

Computer modelling of a convective steam superheater

Computer modelling of a convective steam superheater Computer modelling of a convective steam superheater MARCIN TROJAN* Institute of Thermal Power Engineering, Faculty of Mechanical Engineering Cracow University of Technology Al. Jana Pawła II 37, 31-864

More information

Numerical Simulation of Flexural-tensile Properties of Reinforced Concrete Beam

Numerical Simulation of Flexural-tensile Properties of Reinforced Concrete Beam American Journal of Engineering and Applied Sciences Original Research Paper Numerical Simulation of Flexural-tensile Properties of Reinforced Concrete Beam 1,2 Shi Di, 2 Wang Juan and 1 Liu Jianjun 1

More information

SLIDING WEAR AND FRICTION BEHAVIOR OF FUEL ROD MATERIAL IN WATER AND DRY STATE

SLIDING WEAR AND FRICTION BEHAVIOR OF FUEL ROD MATERIAL IN WATER AND DRY STATE Advanced Materials Development and Performance (AMDP11) International Journal of Modern Physics: Conference Series Vol. (1) 79- World Scientific Publishing Company DOI:.11/S195139 SLIDING WEAR AND FRICTION

More information

The Effect of Swirl Strength on the Flow Characteristics and Separation Efficiency of Supersonic Gas Separator

The Effect of Swirl Strength on the Flow Characteristics and Separation Efficiency of Supersonic Gas Separator The Effect of Swirl Strength on the Flow Characteristics and Separation Efficiency of Supersonic Gas Separator Peiqi Liu 1, Wenwen Ren 1, Jianhua Zhao 1 Yingguang Wang 1, Xiaomin Liu 1, Dapeng Hu 1 * 1

More information

ASME PTC Flow Measurement

ASME PTC Flow Measurement ASME PTC 19.5-2004 Flow Measurement Performance Test Codes A N A M E R I C A N N A T I O N A L S T A N D A R D ASME PTC 19.5-2004 Flow Measurement Performance Test Codes AN AMERICAN NATIONAL STANDARD Three

More information

Heat transfer modelling of slot jet impinging on an inclined plate

Heat transfer modelling of slot jet impinging on an inclined plate Heat transfer modelling of slot jet impinging on an inclined plate A. Ramezanpour 1, H. Shirvani 1 & I. Mirzaee 2 1 School of Design and Communication Systems, APU University, UK 2 CFD Research Centre,

More information

Scale-up & scale-down between the two. worlds of shaken and stirred bioreactors

Scale-up & scale-down between the two. worlds of shaken and stirred bioreactors Scale-up & scale-down between the two worlds of shaken and stirred bioreactors Prof. Dr.-Ing. Jochen Büchs AVT - Biochemical Engineering, RWTH Aachen University Sammelbau Biologie, D - 52074 Aachen, Germany

More information

ISO 3966 INTERNATIONAL STANDARD. Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes

ISO 3966 INTERNATIONAL STANDARD. Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes INTERNATIONAL STANDARD ISO 3966 Second edition 2008-07-15 Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes Mesurage du débit des fluides dans les conduites fermées

More information

A NOVEL TECHNIQUE FOR EXTRACTION OF GEOTHERMAL ENERGY FROM ABANDONED OIL WELLS

A NOVEL TECHNIQUE FOR EXTRACTION OF GEOTHERMAL ENERGY FROM ABANDONED OIL WELLS A NOVEL TECHNIQUE FOR EXTRACTION OF GEOTHERMAL ENERGY FROM ABANDONED OIL WELLS Seyed Ali Ghoreishi-Madiseh McGill University 3450 University St., Room 125 Montreal, QC, Canada H3A2A7 e-mail: seyed.ghoreishimadiseh

More information

ME ENGINEERING THERMODYNAMICS UNIT III QUESTION BANK SVCET

ME ENGINEERING THERMODYNAMICS UNIT III QUESTION BANK SVCET 1. A vessel of volume 0.04m 3 contains a mixture of saturated water and steam at a temperature of 250 0 C. The mass of the liquid present is 9 kg. Find the pressure, mass, specific volume, enthalpy, entropy

More information

Thermal Characteristics and Energy Performance of Double Skin. Façade System in the Hot Summer and Cold Winter Zone

Thermal Characteristics and Energy Performance of Double Skin. Façade System in the Hot Summer and Cold Winter Zone Thermal Characteristics and Energy Performance of Double Skin Façade System in the Hot Summer and Cold Winter Zone L.F. Shu 1, G.Q. He 1,*, S.M. Zhang 1 and Q.A. Bai 2 1 College of Civil Engineering and

More information

RESULTS OF EXPERIMENTAL MEASUREMENTS AND CALCULATIONS OF PRESSURE LOSSES IN HD-PE PIPES. Pavel Mosler, Jan Melichar

RESULTS OF EXPERIMENTAL MEASUREMENTS AND CALCULATIONS OF PRESSURE LOSSES IN HD-PE PIPES. Pavel Mosler, Jan Melichar 18th International Conference on TRANSPORT AND SEDIMENTATION OF SOLID PARTICLES 11-15 September 2017, Prague, Czech Republic ISSN 0867-7964 ISBN 978-83-7717-269-8 RESULTS OF EXPERIMENTAL MEASUREMENTS AND

More information

Lateral Outflow from Supercritical Channels

Lateral Outflow from Supercritical Channels Lateral Outflow from Supercritical Channels J. Coonrod 1, J. Ho 2 and N. Bernardo 3 1 Associate Professor, Department of Civil Engineering, University of New Mexico, Albuquerque, NM 87131; PH (505) 277-3233;

More information

High Compressive Residual Stresses in Through Hardened Steel Parts as a Function of Biot Number

High Compressive Residual Stresses in Through Hardened Steel Parts as a Function of Biot Number High Compressive Residual Stresses in Through Hardened Steel Parts as a Function of Biot Number N..KOBASKO 1, M.A.ARONOV 1, KATSUM CHTAN 2, MAYU HASEGAWA 2, KENRO NOGUCH 2 1 Q Technologies, nc., Akron,

More information

EFFECT OF THE NOZZLE EXIT POSITION ON THE EFFICIENCY OF EJECTOR COOLING SYSTEM USING R134A

EFFECT OF THE NOZZLE EXIT POSITION ON THE EFFICIENCY OF EJECTOR COOLING SYSTEM USING R134A EFFECT OF THE NOZZLE EXIT POSITION ON THE EFFICIENCY OF EJECTOR COOLING SYSTEM USING R134A K. Sopian 1, B. Elhub 1, Sohif Mat 1, A. N. Al-Shamani 1, AM Elbreki 1, Azher M. Abed 1, Husam Abdulrasool Hasan

More information

Estimation of Boil-off-Gas BOG from Refrigerated Vessels in Liquefied Natural Gas Plant

Estimation of Boil-off-Gas BOG from Refrigerated Vessels in Liquefied Natural Gas Plant International Journal of Engineering and Technology Volume 3 No. 1, January, 2013 Estimation of Boil-off-Gas BOG from Refrigerated Vessels in Liquefied Natural Gas Plant Wordu, A. A, Peterside, B Department

More information

Study of flow through combustion swirler with the effect of diffuser on the recirculation zone

Study of flow through combustion swirler with the effect of diffuser on the recirculation zone International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 3, Issue 6 (September 2012), PP. 68-73 Study of flow through combustion swirler

More information

CHEMICAL INJECTION METHODS Pros & Cons

CHEMICAL INJECTION METHODS Pros & Cons CHEMICAL INJECTION METHODS Pros & Cons 1 Chemical injection is an integral component of any pipeline integrity program. The petroleum, chemical, and water treatment industries require chemical treatments

More information

Lecture Retaining Wall Week 12

Lecture Retaining Wall Week 12 Lecture Retaining Wall Week 12 Retaining walls which provide lateral support to earth fill embankment or any other form of material which they retain them in vertical position. These walls are also usually

More information

Performance Comparison of Air-source Heat Pumps Using Economizer Vapor Injection and Internal Heat Exchanger in Cold Regions

Performance Comparison of Air-source Heat Pumps Using Economizer Vapor Injection and Internal Heat Exchanger in Cold Regions Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2016 Performance Comparison of Air-source Heat Pumps Using Economizer Vapor

More information

Simulation of Transient Temperature Field in the Selective Laser Sintering Process of W/Ni Powder Mixture

Simulation of Transient Temperature Field in the Selective Laser Sintering Process of W/Ni Powder Mixture Simulation of Transient Temperature Field in the Selective Laser Sintering Process of W/Ni Powder Mixture Jiwen Ren, Jianshu Liu, and Jinju Yin The School of Electromechanical Engineering, East China Jiaotong

More information

Effect of alumina nanoparticles in the fluid on heat transfer in double-pipe heat exchanger system

Effect of alumina nanoparticles in the fluid on heat transfer in double-pipe heat exchanger system Korean J. Chem. Eng., 25(5), 966-971 (2008) SHORT COMMUNICATION Effect of alumina nanoparticles in the fluid on heat transfer in double-pipe heat exchanger system Byung-Hee Chun, Hyun Uk Kang, and Sung

More information

Simulation of the Flow in a Packed-Bed with and without a Static Mixer by Using CFD Technique

Simulation of the Flow in a Packed-Bed with and without a Static Mixer by Using CFD Technique Simulation of the Flow in a Packed-Bed with and without a Static Mixer by Using CFD Technique Phavanee Narataruksa, Karn Pana-Suppamassadu, Sabaithip Tungkamani Rungrote Kokoo, and Prayut Jiamrittiwong

More information

Investigation of Rotating Instability in the Last Stage of Low Pressure Turbine during Low volume flow Operation

Investigation of Rotating Instability in the Last Stage of Low Pressure Turbine during Low volume flow Operation Investigation of Rotating Instability in the Last Stage of Low Pressure Turbine during Low volume flow Operation Dilip Kumar Garg 1, Shrinivas Chambalwar 2, Jayant Sarode 3, Ajay Dhanopia 4 1 Department

More information

Derivation of Global Parametric Performance of Mixed Flow Hydraulic Turbine Using CFD. Ruchi Khare, Vishnu Prasad and Sushil Kumar

Derivation of Global Parametric Performance of Mixed Flow Hydraulic Turbine Using CFD. Ruchi Khare, Vishnu Prasad and Sushil Kumar Derivation of Global Parametric Performance of Mixed Flow Hydraulic Turbine Using CFD Ruchi Khare, Vishnu Prasad and Sushil Kumar Ruchi Khare Vishnu Prasad Sushil Kumar Abstract: The testing of physical

More information

Simulation of Flameless Combustion of Natural Gas in a Laboratory Scale Furnace

Simulation of Flameless Combustion of Natural Gas in a Laboratory Scale Furnace Turkish J. Eng. Env. Sci. 30 (2006), 135 143. c TÜBİTAK Simulation of Flameless Combustion of Natural Gas in a Laboratory Scale Furnace Sébastien MURER, Barbara PESENTI and Paul LYBAERT Thermal Engineering

More information

Study on hot extrusion of large-diameter magnesium alloy thin tubes

Study on hot extrusion of large-diameter magnesium alloy thin tubes Study on hot extrusion of large-diameter magnesium alloy thin tubes *Yeong-Maw Hwang 1) and Chia-Ming Hsu 2) 1), 2) Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat- Sen University,

More information

Analysis of Side Sluice in Trapezoidal Channel

Analysis of Side Sluice in Trapezoidal Channel Analysis of Side Sluice in Trapezoidal Channel Dr. L. G. Patil 1, Amol M. Kode 2 1 Associate Professor, Department of Civil Engineering, SGGSIE&T, Nanded 2 M. Tech Student, Department of Civil Engineering,

More information

Thermal Accumulation in Solar Systems for Hot Water Abstract 1. Introduction

Thermal Accumulation in Solar Systems for Hot Water Abstract 1. Introduction Thermal Accumulation in Solar Systems for Hot Water Stanko Vl. Shtrakov, Anton Stoilov South - West University Neofit Rilski, Dept of Physics, 66 Ivan Mihailov Str., 2700 - Blagoevgrad, BULGARIA, E-mail:

More information

Calculation and Analysis the Influence on the Cooling Water Velocity and Hot Metal Circulation to the Long Life Blast Furnace

Calculation and Analysis the Influence on the Cooling Water Velocity and Hot Metal Circulation to the Long Life Blast Furnace Journal of Materials Science and Engineering B 5 (1-2) (2015) 36-41 doi: 10.17265/2161-6221/2015.1-2.003 D DAVID PUBLISHING Calculation and Analysis the Influence on the Cooling Water Velocity and Hot

More information

Agenda. Background Validation studies. 3D application. Co-simulation. Summary. Espedal stratified flow. StatOil wavy-slug flow.

Agenda. Background Validation studies. 3D application. Co-simulation. Summary. Espedal stratified flow. StatOil wavy-slug flow. www.cd-adapco.com Computational Flow Assurance Recent progress in modelling of multiphase flows in long pipelines Simon Lo, Abderrahmane Fiala (presented by Demetris Clerides) Subsea Asia 2010 Agenda Background

More information

Effect of air flowrate on particle velocity profile in a circulating fluidized bed

Effect of air flowrate on particle velocity profile in a circulating fluidized bed Korean J. Chem. Eng., 24(5), 851-855 (2007) SHORT COMMUNICATION Effect of air flowrate on particle velocity profile in a circulating fluidized bed Sansanee Kumthanasup and Suchaya Nitivattananon Fuel Research

More information

Finite Element Simulation of Thermal Field in Double Wire Welding

Finite Element Simulation of Thermal Field in Double Wire Welding Journal of Materials Science and Chemical Engineering, 2016, 4, 10-21 http://www.scirp.org/journal/msce ISSN Online: 2327-6053 ISSN Print: 2327-6045 Finite Element Simulation of Thermal Field in Double

More information

Refrigeration Cycle With Two-Phase Condensing Ejector

Refrigeration Cycle With Two-Phase Condensing Ejector Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2006 Refrigeration Cycle With Two-Phase Condensing Ejector Mark J. Bergander

More information

Study on the thermal protection performance of superalloy honeycomb panels in high-speed thermal shock environments

Study on the thermal protection performance of superalloy honeycomb panels in high-speed thermal shock environments THEORETICAL & APPLIED MECHANICS LETTERS 4, 021004 (2014) Study on the thermal protection performance of superalloy honeycomb panels in high-speed thermal shock environments Dafang Wu, 1, a) Anfeng Zhou,

More information

4th Annual International Conference on Material Science and Engineering (ICMSE 2016)

4th Annual International Conference on Material Science and Engineering (ICMSE 2016) Effect of Layer Thickness on Natural Frequency of the Adhesively Bonded Steel Disc Structure Min YOU 1, 2, a,*, Ying-Ying LI 1, b, Jian-Li LI 2, c and Wen-Jun LIU 1, d 1 Hubei Key Laboratory of Hydroelectric

More information

Investigations Of Low Pressure Two-Phase Steam- Water Injector

Investigations Of Low Pressure Two-Phase Steam- Water Injector Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 206 Investigations Of Low Pressure Two-Phase Steam- Water Injector Roman Kwidzinski

More information