G R AV E R T E C H N O L O G I E S

Transcription

1

2 GRAVER TECHNOLOGIES

3 Company Profile Graver Technologies offers a broad selection of liquid process filters, high performance specialty ion exchange resins and services, and proprietary adsorbents for the most demanding application environments. We also supply filtration products to manufacturers of pumps, turbines, compressors, medical devices, and consumer and industrial vacuums. Because of the breadth of our technologies and the depth of our scientific and analytical resources, we are often called upon to solve our customers most challenging problems. Graver Technologies serves industries that include: Process Water Power Generation Food & Beverage Drinking Water Pharmaceutical Chemical Liquid Process Filter Group The products found in this catalog are offered by Graver s Liquid Process Filter Group. Graver Technologies offers an extensive line of filter cartridges and housings to provide high performance and cost effective solutions for liquid process applications. With filters suitable for common industrial, high purity water and other critical process streams, Graver Technologies liquid process filters service a wide array of applications in the beverage, chemical, microelectronics, and biopharmaceutical markets. Our membrane filters are constructed in a state-of-the-art manufacturing facility that includes an ISO Class 7 clean room to meet the most demanding customer requirements. Graver Technologies liquid process filters are also available in a wide range of media types, cartridge designs, micron ratings, and configurations to optimize filtration efficiency while providing dependable performance and long service life. Global Presence Exporting on average more than 35% of our products, Graver Technologies is recognized worldwide. Our global presence extends from North and South America, across Europe and into Asia including the Pacific Rim, Japan, and Australia. We are headquartered in Glasgow, Delaware, with additional manufacturing and marketing facilities in Newark, New Jersey and Honeoye Falls, New York. Our Parent Company Graver Technologies is a member of The Marmon Group (a Berkshire Hathaway company), an international corporation with more than $7 billion in annual sales. Around the corner or around the world, Graver Technologies is a fast-growing company with the technical resources and financial strength that make us the perfect partner for your business

4 Filtration Separation Purification Quality System Graver Technologies is an ISO 9001 registered firm under BSI Management Systems. Quality at Graver means: Every employee is responsible for quality Continuous improvements in products and processes Doing the job right the first time Continually monitoring key processes Preventing nonconformance Producing to established specifications Providing consistent and reliable products Monitoring and improving customer satisfaction levels On time delivery Working with capable vendors Understanding our customer s needs Delighting our customers At Graver our people and our products reflect our commitment to provide the best value to our customers, to create products that reflect the most advanced technology, and to adhere to manufacturing practices that deliver consistent, high performance products and service each and every time.

5 Filter End Configurations Gravers offers a wide variety of end configurations on our filter cartridges to meet customer requirements and for fit in installed housings. The following guide will familiarize you with the options available. Style DOE or SOE Style DOE or SOE P DOE Thermally bonded-plastic caps with DBG DOE flat gasket seal on both open ends Santoprene gaskets bonded on both open ends P3 SOE 222 double o-ring Flat on P6 SOE on open end closed end P3-222/FLAT Plastic spring on closed end Gasket or NN on open end P8 SOE 222 double o-ring Spear on P9 SOE on open end closed end P8-222/FIN Plastic spring on closed end Extended core on open end P2 SOE 226 double o-ring Flat on PX DOE on open end closed end Flat gasket or NN on both open ends with extended core on one end P7 SOE 226 double o-ring Spear on AM SOE on open end closed end Internal o-ring on open end Recessed cup on closed end NN DOE No endcaps/no o-rings or gaskets NPC DOE on both open ends NN - NONE STRATUM Internal o-rings on both open ends * DOE = Double Open End / SOE = Single Open End Note: that not all configurations are available on every product. Please consult specific product data sheets for more detail. Customer Service: International Customer Service :

6 Filtration Separation Purification

7 Table of Contents Membrane Filters TefTEC WaterTEC ZTEC B ZTEC E ZTEC G ZTEC P ZTEC WB Pleated Filters GFC GFP High Flow High Flow GF PMA PMC QCR QMA QMC QXL Depth Filters COAX Crystal MBF MBC Stratum A Stratum C Specialty GSTACK Modules RTEC P Steris Replacement TPM Housings GSTACK High Flow IHP LPF MC SC SHP Membrane Filters Pleated Filters Depth Filters Specialty Housings Customer Service: International Customer Service :

8 Filtration Separation Purification 2

9 Membrane Filters Membrane Filters Graver Product Media Hardware Retention Ratings (μm) Efficiency TefTec PTFE Polypropylene 0.05, 0.1, 0.2, 0.45, 1.0 Absolute WaterTec Polyethersulfone Polypropylene 0.05, 0.1, 0.2, 0.45, 0.65 Absolute ZTEC B Polyethersulfone Polypropylene 0.2, 0.45, 0.65 Absolute ZTEC E Polyethersulfone Polypropylene 0.03, 0.1, 0.2, 0.45 Absolute ZTEC G Polyethersulfone Polypropylene 0.1, 0.2, 0.45, 0.65 Absolute ZTEC P Polyethersulfone Polypropylene 0.2 Absolute ZTEC WB Polyethersulfone Polypropylene 0.2, 0.45, 0.65, 1.2 Absolute Customer Service: International Customer Service :

10 Filtration Separation Purification TefTEC Series Filter Cartridges Absolute Rated PTFE Membrane Filter Cartridges TefTEC cartridge filters are constructed with naturally hydrophobic PTFE membrane and polypropylene support layers and components. The HIMA retentive PTFE membrane offers superior hydrophobicity and water intrusion resistance compared to PVDF and polypropylene membranes, and the cartridge construction offers a costeffective alternative to all-fluorocarbon filters. TefTEC filters are ideal for gas/vent applications and the filtration of aggressive chemicals and solvents. Features Benefits High surface area, single-layer construction provides superior flow rates and minimizes filtration system size 100% Flushed with 18 M -cm DI water and integrity tested Filters are manufactured, flushed, tested and packaged in an ISO Class 7 Cleanroom Environment. Each filter element stamped with pore size, lot and serial number for identification and traceability. Complete qualification guide available Product Specifications Media: Expanded PTFE membrane Inner core, end caps, cage: Support layers: Gaskets/O-Rings: Micron ratings: Polypropylene Polypropylene Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-rings only). Teflon (gasket only) 0.05, 0.1, 0.2, 0.45, 1.0 μm Dimensions Typical Nominal 5", 9.75", 10", 20", 30", 40" lengths: (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.9 cm) Inside diameter: 1.0" (2.54 cm) Surface area: 8.5 ft 2. (0.79 m 2 ) 10" element Operating Parameters Maximum operating temperature: 203 F (95 C) Maximum F ( C) differential pressure: F ( C) F ( C) Maximum reverse differential pressure: F ( C) Recommended change-out pressure: 35 psid (2.4 bar) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, , and , as applicable for food and beverage contact. Typical Applications Aggressive chemicals Strong acids/bases Solvents Tank Vents Compressed gases Photoresists Hot DI water Pharmaceutical Intermediates Fermentation air 4

11 Membrane Filters Differential Pressure TefTEC Nomenclature Information TefTEC P2 S Filter Type TefTEC Series Filters Retention Rating (microns) Nominal Length (inches) Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI TefTEC FLOW RATE 0.05 μm 0.1 μm 0.2 μm 0.45 μm 1.0 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise TefTEC AIR FLOW RATE End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring NPC Double Open End, internal O-Ring Example: TefTEC P2S Performance Specifications Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) T Teflon (gasket only) Steam/Autoclave Cartridges will withstand at least 100 steam/autoclave 30 minute 275 F (135 C) Integrity Test Values Air Diffusion per 10 inch cartridge wet with 60/40 IPA/water. Contact Graver Technologies for specific method. Pore Size Specification 0.05 μm: psig (1.5 bar) 0.1 μm: psig (1.2 bar) 0.2 μm: psig (0.8 bar) 0.45 μm: 15 5 psig (0.34 bar) 1.0 μm: 15 3 psig (0.2 bar) Membrane Filters Differential Pressure BAR PSI Air Flow Rate (per 10''cartridge) SCFM 0.05, 0.1 μm 0.2 μm 0.45 μm 1.0 μm M 3 /HR Test conditions: System pressure at <10 psig (vent), 65 F (18 C), outlet open to atmosphere Differential Pressure BAR PSI TefTEC AIR FLOW RATE Air Flow Rate (per 10''cartridge) 0.05, 0.1 μm 0.2 μm 0.45 μm 1.0 μm SCFM M 3 /HR Test conditions: System pressure at 30 psig, 65 F (18 C) Customer Service: International Customer Service :

12 Filtration Separation Purification WaterTEC Series Filter Cartridges Absolute Rated Polyethersulfone Membrane Filter Cartridges The WaterTEC filter series is constructed of absolute rated, hydrophilic, asymmetric polyethersulfone membrane and polypropylene components. The filter is designed for overall filtration economy and provides excellent flow rates and throughputs. Features Benefits Low pressure drop reduces energy costs High dirt holding capacity minimizes change-outs and down time All thermal bonded construction with no adhesives Available in all common configurations to allow use of existing filter housings Cost effective absolute filtration Product Specifications Media: Asymmetric polyethersulfone Inner core, end caps,cage: Polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only), Teflon (gasket only) Micron ratings: 0.05, 0.1, 0.2, 0.45, 0.65 μm Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.7, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.9 cm) Inside diameter: 1.0 (2.54 cm) Surface area: 6 ft 2.. (0.56 m 2 ) per 10 inch element Operating Parameters Maximum sustained operating temperature: Maximum differential pressure: Maximum reverse differential pressure: Recommended change-out pressure: 180 F (82 C) at 20 psid (1.38 bar) F ( C) F ( C) F ( C) F ( C) 35 psid (2.4 bar) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, , and as applicable for food and beverage contact. European Directive for Direct Food Contact - European Regulations No 1935/2004 and European directive 82/711/EEC: Tested for migration behavior in direct food contact. Minimal rinse required for use. Data available upon request. Typical Applications General water filtration DI water prefilter DI water post filter Aqueous based chemical processing 6

13 Membrane Filters WaterTEC Nomenclature Information WaterTEC P2 E -R Filter Type WaterTEC Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring Pre-Rinse Option -R Factory Pre-Rinse Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) T Teflon (gasket only) Membrane Filters Example: WaterTEC P2E Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI 0.05 μm 0.1 μm WaterTEC FLOW RATE 0.2 μm 0.45 μm 0.65 μm Performance Specifications Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with ph range from Consult factory for specific compatibility information USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Customer Service: International Customer Service :

14 Filtration Separation Purification ZTEC B Series Filter Cartridges Pleated Polyethersulfone (PES) Membrane for Bioburden Reduction in Beverages and Biopharmaceuticals ZTEC B Bioburden Reduction grade membrane cartridges provide highly consistent performance for bioburden reduction and particle removal across a wide range of beverage, pharmaceutical and biological fluids. The naturally hydrophilic PES membrane filters provide exceptional flow rates, long on-stream life, broad chemical compatibility and have no added surfactants to contribute to extractables. The cartridges are integrity testable and steamable to assure reliable service in critical applications. Features Benefits Manufactured in an ISO Class 7 Cleanroom Environment 100% flushed with ultrapure DI water and integrity tested Repeatably Steamable/Sanitizable High retentions up to 10 7 /cm 2 challenged for bacteria and yeast Pore size, lot and serial number are stamped on each filter element for identification and traceability Complete qualification guide available Quick wet treatment available Product Specifications Media: Asymmetric Polyethersulfone membrane Inner core, end caps,cage: Polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only) Micron ratings: 0.2, 0.45, 0.65 μm Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.7, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.9 cm) Inside diameter: 1.0" (2.54 cm) Surface area: 7.6 ft 2. (0.7 m 2 ) per 10" element Operating Parameters Maximum sustained operating temperature: Maximum differential pressure: Maximum reverse differential pressure: Recommended change-out pressure: 176 F (80 C) at 20 psid (1.38 bar) F ( C) F ( C) F ( C) F ( C) 35 psid (2.4 bar) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, , and as applicable for food and beverage contact. European Directive for Direct Food Contact - European Regulations No 1935/2004 and European directive 82/711/EEC: Tested for migration behavior in direct food contact. Minimal rinse required for use. Data available upon request. Typical Applications Bottled Water Ophthalmic Solutions Culture Media Reagent Chemicals LVPs Buffers Juices 8

15 Membrane Filters ZTEC B Nomenclature Information ZTEC B P2 E -QW Filter Type ZTEC B Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring NPC Double open end, internal O-Ring Quickwet treatment Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) Membrane Filters Example: ZTECB P2E Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI ZTEC B FLOW RATE 0.2 μm 0.45 μm 0.65 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Performance Specifications Hot DI Water Filter cartridge will withstand temperatures of 185 F (85 C) for up to 30 consecutive minutes. Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with ph range from Consult factory for specific compatibility information. Steam/Autoclave Cartridges may be steamed or autoclaved for at least 50 thirty minute 275 F (135 C). Typical Bacterial Retention Performance 0.2 μm: LRV for B. diminuta μm: LRV for S. marcescens μm: LRV for S. cerevisiae 11 Integrity Test Specifications Minimum Bubble Point values and maximum Diffusive Air Flow (per 10-inch cartridge) values for ZTEC-B filters wet with water: Pore Size Bubble Point Diffusive Air Flow 0.2 μm: 38 psig (2.6 bar) psig (2.1 bar) 0.45 μm: 25 psig (1.7 bar) psig (1.4 bar) 0.65 μm: 18 psig (1.2 bar) psig (1.0 bar) Customer Service: International Customer Service :

16 Filtration Separation Purification ZTEC E Series Filter Cartridges Pleated Polyethersulfone (PES) Membrane for Final Filtration of Ultrapure Water ZTEC E microelectronics grade cartridges represent Graver s latest development in ultrapure water filtration technology. The filters are inherently hydrophilic and contain no added surfactants or wetting agents that could contaminate pure and ultrapure water streams. The PES membrane offers superior flow characteristics, high contaminant capacity and consistent removal of submicron particles. The cartridges exhibit rapid rinse-up to 18 M -cm resistivity and single digit ppb levels of TOC. Features Benefits Manufactured, flushed, tested and packaged, in an ISO Class 7 Cleanroom Environment. Filters are100% flushed with 18 M -cm DI water and integrity tested. Resistivity rinse-up to 18 M -cm and single digit ppb TOC levels with minimal throughput. Available in a variety of end cap/adapter configurations to fit all industry-standard housings. Pore size, lot and serial number are stamped on each filter element for identification and traceability. Complete qualification guide available. Product Specifications Media: Asymmetric Polyethersulfone membrane Inner core, end caps,cage:polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only) Micron ratings: 0.1, 0.2, 0.45, 0.65 μm Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.7, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.9 cm) Inside diameter: 1.0" (2.54 cm) Surface area: 7.0 ft 2. (0.65 m 2 ) per 10" element Certifications ZTEC E filters were tested by outside laboratory, CT Associates in November, 2011 for the following: TOC Rinse-up to 0.5 ppb Resistivity Rinse-up to 18 MΩ-cm Non-Volatile Residue Particle Rinse-up Trace Metal Extractables Anion and Cation Extractables Please request Graver ZTEC E Qualification Guide for details and complete test reports. Typical Applications DI water High purity chemicals Operating Parameters Maximum sustained operating temperature: 176 F (80 C) at 20 psid (1.38 bar) Maximum differential pressure: Maximum reverse differential pressure: Recommended change-out pressure: F ( C) F ( C) F ( C) F ( C) 35 psid (2.4 bar) 10

17 Membrane Filters ZTEC E Nomenclature Information ZTEC E P8 T Filter Type ZTEC E Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring NPC Double open end, internal O-Ring Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) Membrane Filters Example: ZTECE P8T Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI μm ZTEC E FLOW RATE 0.1 μm 0.2 μm 0.45 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Performance Specifications Hot DI Water Filter cartridge will withstand temperatures of 185 F (85 C) for up to 30 consecutive minutes. Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with ph range from Consult factory for specific compatibility information. Rinse-Up Volumes Resistivity rinse-up to 18 M -cm: <30 minutes at a flow of 3 gpm per 10-inch element. Rinse-up to single digit ppb TOC in <120 minutes at a flow of 3 gpm per 10-inch element. Integrity Test Specifications Minimum Bubble Point values and maximum Diffusive Air Flow (per 10-inch cartridge) values for ZTEC-E filters wet with water: Pore Size Diffusive Air Flow 0.03 μm: psig (3.1 bar) 0.1 μm: psig (2.8 bar) 0.2 μm: psig (2.1 bar) 0.45 μm: psig (1.4 bar) Customer Service: International Customer Service :

18 Filtration Separation Purification ZTEC G Series Filter Cartridges Absolute Rated Polyethersulfone Membrane Pleated Filter Cartridges This pleated, disposable filter element is constructed of absolute rated, hydrophilic, asymmetric polyethersulfone membrane with extended filter area to allow for a high system flow rate. Features Benefits 7.0 ft 2 (0.65 m 2 ) of membrane surface area per 10" element High throughput Longer on-line service reduces costly maintenance time Absolute rated membrane from 0.1 to 0.65 μm Manufactured in an ISO Class 7 cleanroom environment 100% flushed with 18 M -cm DI water and gross integrity tested Fixed pore construction eliminates dirt unloading as differential pressure increases Low extractables Product Specifications Media: Asymmetric Polyethersulfone membrane Inner core, end caps,cage:polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only) Micron ratings: 0.1, 0.2, 0.45, 0.65 μm Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.7, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.9 cm) Inside diameter: 1.0" (2.54 cm) Surface area: 7.0 ft 2. (0.65 m 2 ) per 10" element Operating Parameters Maximum sustained operating temperature: 176 F (80 C) at 20 psid (1.38 bar) Maximum differential pressure: Maximum reverse differential pressure: Recommended change-out pressure: F ( C) F ( C) F ( C) F ( C) 35 psid (2.4 bar) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, , and as applicable for food and beverage contact. European Directive for Direct Food Contact - European Regulations No 1935/2004 and European directive 82/711/EEC: Tested for migration behavior in direct food contact. Minimal rinse required for use. Data available upon request. Typical Applications Food & Beverage Filtration of acids and bases Cosmetics Ink Chemicals Ultra pure water Aqueous solutions 12

19 Membrane Filters ZTEC G Nomenclature Information ZTEC G P7 T Filter Type ZTEC G Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring NPC Double open end, internal O-Ring Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) Membrane Filters Example: ZTECG P7S Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI 0.1 μm ZTEC G FLOW RATE 0.2 μm 0.45 μm 0.65 μm Performance Specifications Hot DI Water Filter cartridge will withstand temperatures of 185 F (85 C) for up to 30 consecutive minutes. Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with ph range from Consult factory for specific compatibility information. Steam/Autoclave Cartridges may be steamed or autoclaved for at least 50 thirty minute 275 F (135 C) USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Customer Service: International Customer Service :

20 Filtration Separation Purification ZTEC P Series Filter Cartridges Pleated Polyethersulfone (PES) Membrane for Sterile Filtration ZTEC P Sterilizing Grade membrane cartridges are HIMA validated for complete bacterial retention to yield product sterility in biopharmaceutical final filtration applications. The naturally hydrophilic and low protein binding characteristics of polyethersulfone membrane ensure maximum transmission of active ingredients making it ideal for a wide range of pharmaceutical and biological liquid applications, including the filtration of therapeutics, vaccines, antibiotics, bulk pharmaceutical and other critical biotechnology products. The double-layer PES 0.2 micron membrane filters are manufactured in a cleanroom environment, and integrity tested before shipment to assure consistent performance and quality. Features Benefits Manufactured in an ISO Class 7 Cleanroom Environment 100% flushed with ultrapure DI water Meets ASTM Standards for Sterility Repeatably Steamable/Sanitizable 100% Integrity tested prior to release Pore size, lot and serial number are stamped on each filter element for identification and traceability Complete validation guide available Product Specifications Media: Asymmetric Polyethersulfone membrane Inner core, end caps, cage:polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only) Micron ratings: 0.2 μm Dimensions Nominal lengths: 10", 20", 30", 40" (25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.9 cm) Inside diameter: 1.0" (2.54 cm) Surface area: 6.8 ft 2. (0.63 m 2 ) per 10" element Operating Parameters Maximum sustained operating temperature: 176 F (80 C) at 20 psid (1.38 bar) Maximum differential pressure: Maximum reverse differential pressure: Recommended change-out pressure: F ( C) F ( C) F ( C) F ( C) 35 psid (2.4 bar) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, , and as applicable for food and beverage contact. European Directive for Direct Food Contact - European Regulations No 1935/2004 and European directive 82/711/EEC: Tested for migration behavior in direct food contact. Minimal rinse required for use. Data available upon request. Typical Applications Diagnostics Ophthalmic Solutions Culture Media Reagent Chemicals LVPs Buffers Vaccines 14

21 Membrane Filters ZTEC P Nomenclature Information ZTEC P P2 S Filter Type ZTEC P Series Filters Retention Rating (microns) 0.2 Nominal Length (inches) End Configuration P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) Membrane Filters Example: ZTECP P2S Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI 0.2 μm ZTEC P FLOW RATE USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Performance Specifications Hot DI Water Filter cartridge will withstand temperatures of 185 F (85 C) for up to 30 consecutive minutes. Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with ph range from Consult factory for specific compatibility information. Steam/Autoclave Cartridges may be steamed or autoclaved for at least 50 thirty minute 275 F (135 C). Typical Bacterial Retention Performance Cartridges have been validated for the complete retention of Brevundimonas diminuta at a challenge level of 10 7 organisms/cm 2 as prescribed in ASTM Integrity Test Specifications Minimum Bubble Point values and maximum Diffusive Air Flow (per 10-inch cartridge) values for ZTEC-P filters wet with water: Pore Size Bubble Point Diffusive Air Flow 0.2 μm: 40 psig (2.8 bar) psig (2.2 bar) Customer Service: International Customer Service :

22 Filtration Separation Purification ZTEC WB Series Filter Cartridges Pleated Polyethersulfone (PES) Membrane for Critical Filtration in Beverage Applications Protect your beverage from spoilage. ZTEC WB cartridge filters utilize a special polyethersulfone membrane to provide consistent removal of spoilage organisms and inorganic particulate. The product offers excellent retention efficiency and extended on-stream life making it an ideal filter for the clarification of beer, wine and bottled water. The PES membrane, available from 0.2 to 1.2 μm pore sizes, is designed to meet and surpass the filtration criteria necessary to maintain product quality and characteristics. Produced in an ISO Class 7 cleanroom, the cartridges are integrity tested during production to assure performance and consistency. Features Benefits Manufactured in an ISO Class 7 Cleanroom Environment 100% flushed with ultrapure DI water and integrity tested Low adsorption of protein, color and flavor components Steamable/sanitizable for cleaning and reuse High log reduction values for spoilage organisms PES membrane provides high capacity contaminant loading Complete qualification guide available Quick wet treatment available Product Specifications Media: Asymmetric Polyethersulfone membrane Inner core, end caps, cage:polypropylene Support layers: Spunbonded Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only) Micron ratings: 0.2, 0.45, 0.65, 1.2 μm Dimensions Nominal lengths: 9.75" 10", 20", 30", 40" (24.7, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7 (6.9 cm) Inside diameter: 1.0" (2.54 cm) Surface area: 7.6 ft 2. (0.7 m 2 ) per 10" element Operating Parameters Maximum sustained operating temperature: 176 F (80 C) at 20 psid (1.38 bar) Maximum F ( C) differential pressure: F ( C) Maximum reverse differential pressure: F ( C) Recommended change-out pressure: 35 psid (2.4 bar) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, , and as applicable for food and beverage contact. European Directive for Direct Food Contact - European Regulations No 1935/2004 and European directive 82/711/EEC: Tested for migration behavior in direct food contact. Minimal rinse required for use. Data available upon request. Typical Applications White Wine Red Wine Sparkling Wine Wine/Malt Coolers Champagne Distilled Spirits Bottled Water Beer 16

23 Membrane Filters ZTEC WB Nomenclature Information ZTEC WB P2 S -QW Filter Type ZTEC WB Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring Quickwet treatment Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) Membrane Filters Example: ZTECWB P2E Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI ZTEC WB FLOW RATE 0.2 μm 0.45 μm 0.65, 1.2 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Performance Specifications Hot DI Water Filter cartridge will withstand temperatures of 185 F (85 C) for up to 30 consecutive minutes. Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with ph range from Consult factory for specific compatibility information. Steam/Autoclave Cartridges may be steamed or autoclaved for at least 50 thirty minute 275 F (135 C). Typical Bacterial Retention Performance 0.20μm: LRV for Pseudomon aeruginosa μm: LRV for Lactobacillus brevis μm: LRV for Oenococcus oeni μm: LRV for S. cerevisiae μm: LRV for S. cerevisiae μm: LRV for S. cerevisiae 8 Integrity Test Specifications Minimum Bubble Point values and maximum Diffusive Air Flow (per 10-inch cartridge) values for ZTEC WB filters wet with water: Pore Size Bubble Point Diffusive Air Flow 0.20 μm: 30 psig (2.1 bar) psig (1.7 bar) 0.45 μm: 20 psig (1.4 bar) psig (1.1 bar) 0.65 μm: 17 psig (1.2 bar) psig (1.0 bar) 1.2 μm: 13 psig (0.9 bar) psig (0.8 bar) Customer Service: International Customer Service :

24 Filtration Separation Purification 18

25 Pleated Filters Graver Product Type Media Hardware Retention Ratings (μm) Efficiency GFC Micro fiberglass Polypropylene 0.2, 0.45, 1, 3, 10, 30 Nominal Pleated Microfiberglass Beta 10 GFP Micro fiberglass Polyester 0.2, 0.45, 1, 3, 10, 30 Nominal Pleated Microfiberglass Beta 10 Pleated Filters High Flow Polypropylene Polypropylene 1, 3, 5, 10, 20, 40, 60, 100 Absolute Pleated Melt Blown Sheet Beta 1000 High Flow GF Microfiberglass Polypropylene, 1, 2.5, 4.5, 10, 20 Absolute Pleated Microfiberglass Polyacetal/ Polyester Beta 1000 PMA Polypropylene Polypropylene 0.2, 0.45, 1, 2.5, 5, 10, Absolute Pleated Melt Blown Sheet 25, 50, 100 Beta 5000 PMC Polypropylene Polypropylene 0.2, 0.25, 0.45, 0.5, Nominal Pleated Melt Blown Sheet 1, 2, 5, 10, 25, 50 Beta 10 QCR Polypropylene Polypropylene 1 Absolute Pleated Melt Blown Sheet NSF/ANSI 53 QMA Polypropylene Polypropylene 0.2, 0.45, 1, 2.5, 5, 10, 20 Absolute Pleated Melt Blown Sheet Beta 5000 QMC Polypropylene Polypropylene 0.1, 0.2, 0.4, 0.6, 1, 3, 5, 10 Nominal Pleated Melt Blown Sheet Beta 20 QXL Polypropylene Polypropylene 0.45, 0.5, 1, 3, 5, 10, 20, 40 Absolute Pleated Melt Blown Sheet Beta 100 Customer Service: International Customer Service :

26 Filtration Separation Purification GFC Series Filter Cartridges Glass Fiber Cartridges (GFC) This high efficiency, disposable filter element is suited for a wide range of applications. The filter is constructed of pleated Borosilicate Microfiberglass filter media with greater surface area for high system flow rate. Features Benefits Micron ratings from 0.2 to 30 μm Broad application range Uniform pore size High removal efficiency High surface area High flow capability and dirt holding capacity Long service life Minimizes maintenance costs Fixed pore construction Eliminates dirt unloading at maximum differential pressure Product Specifications Media: Borosilicate Microfiberglass with Acrylic Binder Inner core: Polypropylene Support layers: Polyester End caps: Polypropylene Cage: Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Teflon Encapsulated Viton (O-Rings only) Micron ratings: 0.2, 0.45, 1.0*, 3.0, 10, 30 μm Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.9 cm) Inside diameter: 1.0" (2.54 cm) Operating Parameters Maximum operating temperature: 176 F (80 C) Maximum F ( C) differential pressure: F ( C) Recommended change-out pressure: 35 psid (2.4 bar) Typical Applications Wine prefiltration Chemicals Blowdown post filter Inks Magnetic tape coatings Oil & Gas * 1 micron grade features all FDA listed materials of construction. 20

27 Pleated Filters GFC Nomenclature Information GFC 3-10 P7 B -I Filter Type GFC Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring NPC Double open end, internal O-Ring Insert -I endcap insert for steaming Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) Pleated Filters Example: GFC 3-10P7B-1 Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI GFC FLOW RATE 0.2 μm μm 1 μm 3 μm μm 30 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Removal Efficiency Beta Ratio Beta 10 Beta 20 Beta 100 Beta 1000 Beta 5000 Efficiency 90% 95% 99% 99.9% 99.98% 0.2 micron micron micron microns microns microns Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 2.5 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Customer Service: International Customer Service :

28 Filtration Separation Purification GFP Series Filter Cartridges High Temperature Glass Fiber Cartridges (GFP) This high efficiency, disposable filter element is suited for a wide range of applications. The filter is constructed of pleated Borosilicate Microfiberglass filter media with greater surface area for high system flow rate. Features Benefits Polyester hardware extends application range beyond the limits of polypropylene. Higher temperature capability of 230 F (110 C) Micron ratings from 0.2 to 30 μm Broad application range Uniform pore size High removal efficiency High surface area High flow capability and dirt holding capacity Long service life Minimizes maintenance costs Fixed pore construction Eliminates dirt unloading at maximum differential pressure Product Specifications Media: Borosilicate Microfiberglass with Acrylic Binder Inner core: Polyester Support layers: Polyester End caps: Polyester Cage: Polyester Gaskets/O-Rings : Buna-N, EPDM, Silicone, Teflon Encapsulated Viton (O-Rings only) Micron ratings: 0.2, 0.45, 1.0, 3.0, 10, 30 μm Dimensions Nominal lengths: 5, 9.75, 10, 20, 30, 40 (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7 (6.9 cm) Inside diameter: 1.0 (2.54 cm) Typical Applications Petrochemicals Chemicals Solvents Inks Oil & Gas Lube Oil Operating Parameters Maximum operating temperature: 230 F (110 C) Maximum differential pressure: Recommended change-out pressure: F ( C) F ( C) F ( C) 35 psid (2.4 bar) 22

29 Pleated Filters GFP Nomenclature Information GFP 3-10 P3 B Filter Type GFP Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) Pleated Filters Example: GFP 3-10P3B Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI GFP FLOW RATE 0.2 μm μm 1 μm 3 μm μm 30 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Removal Efficiency Beta Ratio Beta 10 Beta 20 Beta 100 Beta 1000 Beta 5000 Efficiency 90% 95% 99% 99.9% 99.98% 0.2 micron micron micron microns microns microns Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 2.5 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Customer Service: International Customer Service :

30 Filtration Separation Purification High Flow Series Filter Cartridges Large Geometry Pleated Filters for High Flow Graver High Flow Series filters feature a larger geometry to handle higher flows with fewer filter elements. The result is much faster, easier filter changeouts. In addition, the inside to outside flow allows for excellent dirt holding capacity, extending the time between filter changeouts. Filter housings are also available and because of the filters high flow and dirt holding capacity, smaller systems are possible, reducing upfront capital costs. Features - Benefits 6" diameter, large geometry for high flow rates Absolute retention ratings from 1 to 100 microns Capable of flow rates up to 500 GPM in a single 60" element Inside-out flow retains contaminant even during changeout Multi layer pleated construction with optimized surface area Outer cage prevents media extrusion problem experienced with some competitive offerings Unique Quad Seal gasket provides maximum seal integrity Retrofits competitive high flow filter housings Thermally bonded construction Product Specifications Media/Support/Cage: Polypropylene End caps: Polypropylene O-Rings: EPDM, Silicone, Buna-N, Viton Micron ratings: 1, 3, 5, 10, 20, 40, 60, 100 μm Dimensions Nominal lengths: 20", 40", 60" (50.8, 101.6, cm) Outside diameter: 6.0" (15.2 cm) Surface area: 24 ft 2. (2.2 m 2 ) per 20" 49 ft 2. (4.6 m 2 ) per 40" element 73 ft 2. (6.8 m 2 ) per 60" element Operating Parameters Maximum operating psid ( bar) temperature: psid ( bar) psid ( bar) Recommended changeout differential pressure: 35 psid (2.4 bar) Maximum flow rates*: 60" element up to 500 GPM (1892 lpm) 40" element up to 350 GPM (1325 lpm) 20" element up to 175 GPM (662 lpm) * Consult factory for sizing assistance based on particle loads. ** O-ring should be replaced after 5 cycles or when a loosening of the seal is detected. Certifications FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. NSF 61 - Certified to NSF/ANSI STD 61 for materials requirements only - Component. Typical Applications Water Systems Chemicals Food and Beverage Pre RO Performance Specifications Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with ph range from Consult factory for specific compatibility information. Cartridge will withstand up to ten 30 minute hot water cycles** at 181 F (83 C) at 5 psid (0.35 bar). Steam/Autoclave Cartridges may be steamed for at least twenty 15 minute 230 F (110 C) not to exceed 3 psid (0.21 bar). 24

31 Pleated Filters High Flow Nomenclature Information High Flow 5-60 E Filter Type High Flow Series Filters Example: HF 5-60E Micron Retention Rating (microns) Length (inches) High Flow Pressure Drop O-Ring S Silicone B Buna-N E EPDM V Viton Element Pressure Drop psid/gpm Element Pressure Drop Mbar/M 3 /Hr 20" 40" 60" 20" 40" 60" Note: For chemical compatibility, flow rates, and temperature requirements please consult the factory or your local Graver distributor. Pleated Filters Removal Efficiency Micron Rating 99.9% 99% 90% Beta Ratio Beta 1000 Beta 100 Beta 10 1 micron micron micron micron micron micron micron micron Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 3 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Customer Service: International Customer Service :

32 Filtration Separation Purification High Flow GF Series Filter Cartridges Large Geometry Pleated Filters for High Flow Graver High Flow GF Series filters feature microfiberglass media in a larger geometry to handle higher flows with fewer filter elements. The result is much faster, easier filter changeouts. In addition, the inside to outside flow allows for excellent dirt holding capacity, extending the time between filter changeouts. Filter housings are also available and because of the filters high flow and dirt holding capacity, smaller systems are possible, reducing upfront capital costs. Features - Benefits Materials of construction allow compatibility with some chemistries not served by all polypropylene elements. 6" diameter, large geometry for high flows Absolute retention ratings from 1 to 20 microns Capable of flow rates up to 500 GPM in a single 60" element Inside-out flow retains contaminant even during changeout Outer cage prevents media extrusion problem experienced with some competitive offerings Unique Quad Seal gasket provides maximum seal integrity Retrofits competitive high flow filter housings Thermally bonded construction Product Specifications Media: Microfiberglass Support/Cage: Polyester or polypropylene End caps: Polyacetal or polypropylene O-Rings: EPDM, Silicone, Buna-N, Viton Micron ratings: 1, 2.5, 4.5, 10, 20 μm Dimensions Nominal lengths: 20", 40", 60" (50.8, 101.6, cm) Outside diameter: 6.0" (15.2 cm) Surface area: 24 ft 2. (2.2 m 2 ) per 20" element 49 ft 2. (4.6 m 2 ) per 40" element 73 ft 2. (6.8 m 2 ) per 60" element Operating Parameters Maximum operating temperature: polyacetal hardware psid ( bar) psid ( bar) polypropylene hardware psid ( bar) psid (82 bar) Recommended changeout differential pressure: 35 psid (2.4 bar) Maximum flow rates: 60" element up to 500 GPM (1892 lpm) 40" element up to 350 GPM (1325 lpm) 20" element up to 175 GPM (662 lpm) * Consult factory for sizing assistance based on particle loads. Typical Applications Fuel Oil Chemicals Petrochemicals Solvents Oil & Gas 26

33 Pleated Filters High Flow GF Nomenclature Information High Flow GF -A E Filter Type High Flow GF Series Filters Example: HFGF -A2.5-60E Micron Hardware Material P Polypropylene A Polyacetal caps polyester cage - Retention Rating (microns) High Flow GF Pressure Drop Element Pressure Drop psid/gpm Length (inches) O-Ring S Silicone B Buna-N E EPDM V Viton Element Pressure Drop Mbar/M 3 /Hr 20" 40" 60" 20" 40" 60" Pleated Filters Note: For chemical compatibility, flow rates, and temperature requirements please consult the factory or your local Graver distributor. Removal Efficiency Micron Rating 99.9% 99% 90% Beta Ratio Beta 1000 Beta 100 Beta 10 1 micron micron micron micron micron Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 3 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Customer Service: International Customer Service :

34 Filtration Separation Purification PMA Series Filter Cartridges Absolute Rated Pleated Filter Cartridges This all polypropylene filter retains particles with absolute efficiency. Available in a broad range of pore sizes, it is suitable for a wide range of applications. The pleated construction provides a high surface area to offer outstanding overall filtration economy. Features Benefits Micron ratings from 0.2 to 100 μm Broad application range Absolute Efficiency Rated at 99.98% (Beta 5000) Competitive surface area High flow rates, and long on-line service Minimize maintenance cost Fixed pore structure Eliminates dirt unloading at maximum differential pressure Polypropylene Construction Inert to many process fluids Various Gasket/O-Ring materials Compatible with a variety of fluids Manufactured in continuous lengths up to 40 inches Product Specifications Media: Polypropylene Inner core: Polypropylene End caps: Polypropylene Cage: Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only), Teflon (gasket only) Polypropylene micron 0.2, 0.45, 1.0, 2.5, 5.0, 10, 25, ratings: 50, 100 μm Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. European Directive for Direct Food Contact - European Regulations No 1935/2004 and European directive 82/711/EEC: Tested for migration behavior in direct food contact. Minimal rinse required for use. Data available upon request. Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.86 cm) Inside diameter: 1.0" (2.54 cm) Operating Parameters Maximum operating 176 F (80 C) temperature: Maximum F ( C) differential pressure: F ( C) Recommended change-out pressure: 35 psid (2.4 bar) 28

35 Pleated Filters Differential Pressure PMA Nomenclature Information PMA P V Filter Type PMA Series Filters Retention Rating (microns) Example: PMA PV Nominal Length (inches) Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI 0.2 μm PMA FLOW RATE 0.45 μm 2 1 μm 2.5 μm 1 5 μm 10, 25, 50 μm 100 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap.viton (O-Rings only) End Configuration T Teflon (gasket only) P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring Removal Efficiency Beta Ratio Beta 5000 Beta 100 Beta 50 Efficiency 99.98% 99% 98% 0.2 micron micron micron microns microns microns microns microns microns Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 3 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Pleated Filters Customer Service: International Customer Service :

36 Filtration Separation Purification PMC Series Filter Cartridges Economically Efficient Pleated Filter Cartridges This cost effective, disposable filter element can be used for a wide range of applications. The filter is constructed of pleated polypropylene filter media with high surface area that allows for greater system flow rate. Features Benefits Micron ratings from 0.2 to 50 μm Broad application range Fixed pore structures Resists unloading of captured contaminant Polypropylene Construction Inert to many process fluids Various Gasket/O-Ring materials Compatible with a variety of fluids Economically efficient filtration Manufactured in continuous lengths up to 40 inches Product Specifications Media: Polypropylene Inner core: Polypropylene End caps: Polypropylene Cage: Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only), Teflon (gasket only) Micron ratings: * 0.2, 0.25, 0.45, 0.5, 1.0, 2.0, 5.0, 10, 25, 50 μm Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.86 cm) Inside diameter: 1.0" (2.54 cm) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. European Directive for Direct Food Contact - European Regulations No 1935/2004 and European directive 82/711/EEC: Tested for migration behavior in direct food contact. Minimal rinse required for use. Data available upon request. Operating Parameters Maximum operating 176 F (80 C) temperature: Differential pressure: F ( C) F ( C) Recommended change-out pressure: 35 psid (2.4 bar) * Other micron rated media available upon request 30

37 Pleated Filters PMC Nomenclature Information PMC 2-20 P8 V Filter Type PMC Series Filters Retention Rating (microns) Example: PMC 2-20P8V Differential Pressure Nominal Length (inches) Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI PMC FLOW RATE μm 0.25 μm μm 0.5 μm 1 μm 1 2 μm 5 μm 10 μm 25 μm 0 50 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring NPC Double open end, internal O-Ring Removal Efficiency Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) T Teflon (gasket only) Beta Ratio Beta 50 Beta 10 Efficiency 98% 90% 0.2 micron micron micron micron micron microns microns microns microns microns Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 3 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Pleated Filters Customer Service: International Customer Service :

38 Filtration Separation Purification QCR Series Filter Cartridges Health Dangers of Cryptosporidium In recent years, significant outbreaks of water borne disease have been traced to Cryptosporidium and Giardia parasites. These naturally occurring organisms are present in many surface water sources and are highly resistant to inactivation by conventional water treatment processes such as chlorination. Healthy individuals typically recover from the common gastrointestinal effects within a few weeks, however for individuals with weakened or undeveloped immune systems, it can be life threatening. In order to ensure the safety of the water supply, standards have been established that define the minimum performance requirements for materials and components of water treatment systems. The QCR Cyst Reduction filter contains an absolute 1 micron filter media designed to exceed the ANSI/NSF Standard 53 of 99.95% for the removal of cysts based upon the polystyrene challenge in water*. Features Benefits Constructed entirely of polypropylene Compatible with most solutions Double O-Ring style ends for the highest seal integrity 7.0 ft 2 (0.65 m 2 ) of effective filter area High flow rates at low pressure drop High dirt capacity Various O-Ring materials and configurations Easily retrofits most systems High surface area High flow rates and long on-line service Product Specifications Media: Polypropylene Core/cage: Polypropylene End caps: Polypropylene O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton Micron rating: 1.0 μm End styles: P2 (226/flat), P3 (222/flat), P7 (226/fin), P8 (222/fin) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. NSF 53 - Performance tested and verified by outside lab to comply with NSF/ANSI Standard 53 for reduction of cryptosporidium and giardia cysts. Operating Parameters Maximum operating temperature: 176 F (80 C) Maximum differential pressure: Recommended change-out pressure: F ( C) F ( C) F ( C) 35 psid (2.4 bar) Dimensions Nominal lengths: 5, 9.75, 10, 20, 30, 40 (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7 (6.86 cm) Inside diameter: 1.0 (2.54 cm) Surface area: 7.0 ft 2. (0.65 m 2 ) * Performance tested and verified by Independent Laboratory Testing. Only the filter end styles offered are certified to meet the cyst reduction claim. 32

39 Pleated Filters QCR Nomenclature Information QCR 1-30 P7 V Filter Type QCR Series Filters Retention Rating (microns) 1 Nominal Length (inches) End Configuration P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton Pleated Filters Example: QCR 1-30P37V Differential Pressure QCR FLOW RATE Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI 0.2 μm μm Performance Specifications Sterilization Cartridges may be autoclaved for 30 minutes at 250 F (121 C) under no end load conditions. May be in-line sanitized one time only in forward flow direction with 185 F (85 C) hot water do not exceed 3 psid USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Customer Service: International Customer Service :

40 Filtration Separation Purification QMA Series Filter Cartridges Absolute Rated High Performance Pleated Polypropylene Filter Cartridge This filter is constructed with a high surface area melt blown polypropylene media for low initial pressure drop, high dirt holding capacity, and high efficiency performance. Features Benefits Micron ratings from 0.2 to 20 μm Broad application range Absolute Efficiency Rated at 99.98% (Beta 5000) High surface area High flow rate, and long service life Minimize maintenance cost Fixed Pore construction Resists dirt unloading at maximum differential pressure Polypropylene Construction Inert to many process fluids Various Gasket/O-ring materials Compatible with many fluids Heavy duty molded cage High structural strength Highly consistent melt blown media for consistent performance Product Specifications Construction material: Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only), Teflon (gasket only) Micron ratings: 0.2, 0.45, 1.0, 2.5, 5.0, 10, 20 μm Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.86 cm) Inside diameter: 1.0" (2.54 cm) Surface area: up to 7.0 ft 2. (0.65 m 2 ) Operating Parameters Maximum operating temperature: 176 F (80 C) Maximum differential F ( C) pressure: F ( C) Recommended change-out pressure: 35 psid (2.4 bar) Performance Specifications Cleaning/Sanitization Compatible with most common chemical cleaning, sanitizing and sterilizing agents and with ph range from Consult factory for specific compatibility information. Cartridge will withstand hot water at 176 F (80 C) at 5 psid (0.35 bar) for 30 minutes. Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. European Directive for Direct Food Contact - European Regulations No 1935/2004 and European directive 82/711/EEC: Tested for migration behavior in direct food contact. Minimal rinse required for use. Data available upon request. Endotoxin level - Limulus Amebocyte Lysate CB028 test indicated bacterial endotoxins were not present in distilled water at 0.25 EU / ml. Extractable content - Test indicate that Non-Volatile Residue, Residue on Ignition and Heavy Metals meet USP limits. Typical Applications Food & beverage Aqueous solutions Chemicals Bottled water Pharmaceuticals Cosmetics Process water RO Prefilters Inks Steam/Autoclave Cartridges may be autoclaved for 30 minutes at 250 F (121 C) under no end load conditions. Cartridges fitted with steam insert may be steamed for at least 10 thirty minute 275 F (135 C) not to exceed 3 psid (0.21 bar). 34

41 Pleated Filters QMA Nomenclature Information QMA 1-20 P3 V -R -I Filter Type QMA Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End PX Extended Core P2 226/Flat Single Open End AM Single open end, P3 222/Flat Single Open End internal O-Ring P7 226/Fin Single Open End NPC Double open end, P8 222/Fin Single Open End internal O-Ring Pre-Rinse Option -R Factory Pre- Rinse Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) T Teflon (Gasket only) Insert -I End cap insert for steaming Pleated Filters Example: QMA 1-20P3V-R-I Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI 0.2 μm QMA FLOW RATE 0.45 μm 1 μm 2.5 μm 5 μm 10 μm 20 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Removal Efficiency Beta Ratio Beta 5000 Beta 100 Beta 50 Efficiency 99.98% 99% 98% 0.2 micron micron micron microns microns microns microns Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 2.5 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Customer Service: International Customer Service :

42 Filtration Separation Purification QMC Series Filter Cartridges High Efficiency Polypropylene Filter Cartridge An innovative product manufactured with multiple layers of melt blown polypropylene media. This unique structure allows high flow rates while maintaining low differential pressure and ideal depth filtration characteristics. Features Benefits Micron ratings from 0.1 to 10 μm Broad application range High Filtration Efficiency 95% Graded pore structure Multilayer, media for high dirt holding capacity Fixed pore construction Resists dirt unloading at maximum differential pressure Polypropylene construction Inert to many process fluids Various Gasket/O-ring materials Compatible with many fluids Product Specifications Construction material: Polypropylene Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only) Micron ratings: 0.1, 0.2, 0.4, 0.6, 1.0, 3.0, 5.0, 10.0 μm Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside diameter: 2.7" (6.9 cm) Inside diameter: 1.0" (2.54 cm) Operating Parameters Maximum operating temperature: 176 F (80 C) Maximum F ( C) differential pressure: F ( C) Maximum reverse differential pressure: F ( C) Recommended change-out pressure: 35 psid (2.4 bar) Performance Specifications Sanitization Hot water at 176 F (80 C) at 5 psid (0.35 bar) for 30 min. In-line steam at 257 F (125 C) at 1psid (0.07 bar) for 30 min. Autoclavable at 257 F (125 C) for 30 min. Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. Endotoxin level - Limulus Amebocyte Lysate CB028 test indicated bacterial endotoxins were not present in distilled water at 0.25 EU / ml. Extractable content - Test indicate that Non-Volatile Residue, Residue on Ignition and Heavy Metals meet USP limits. Typical Applications Food & beverage Aqueous solutions Chemicals Pharmaceuticals Cosmetics Ultrapure water RO Prefilters Ink DE trap Photoresists 36

43 Pleated Filters QMC Nomenclature Information QMC P2 T Filter Type QMC Series Filters Retention Rating (microns) Example: QMC P2T Differential Pressure QMC FLOW RATE Nominal Length (inches) Typical Flow Rate Clean Water at Ambient Temperature BAR PSI (per 10''cartridge) μm μm 0.4 μm μm 1 μm , 5 μm 10 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End PX Extended Core AM Single open end, internal O-Ring NPC Double open end, internal O-Ring Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) Removal Efficiency Beta Ratio Beta 100 Beta 20 Efficiency 99% 95% 0.1 micron micron micron micron micron micron microns microns Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 3 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Pleated Filters Customer Service: International Customer Service :

44 Filtration Separation Purification QXL Series Filter Cartridges Absolute Rated Filtration for Inks, Slurries and Coatings With its extra-loft, extra-life depth filter configuration, the QXL is designed for the filtration of industrial solutions containing agglomerated particles and gels or with high viscosity. Consistent absolute retention performance is achieved throughout the pleated, layered microfiber matrix. The state-of-the-art, optimized structure provides significantly higher flow rates and throughputs than cylindrical melt blown filters. Features Benefits Hybrid pleated depth construction combines graded pore structure with high surface area. Constructed entirely of polypropylene Compatible with a broad range of solutions and chemicals Optimized pleat configuration Provides the ideal combination of retention, flow rate and throughput Excellent gel and agglomerated particle retention reduces defects Available in common end cap configurations Retrofits easily into most filter housings Product Specifications Media: Polypropylene Core,Cage, End Caps: Polypropylene Gaskets/O-Rings: Silicone, Viton, EPDM, Buna, Teflon encapsulated Viton (O-Rings only) Micron Ratings: 0.45, 0.5, 1, 3, 5, 10, 20, 40 μm Dimensions Nominal lengths: 5, 9.75, 10, 20, 30, 40 (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside Diameter: 2.7" (6.86 cm) Inside Diameter: 1.0 (2.54 cm) Operating Parameters Maximum Operating Temperature: 176 F (80 C) Maximum F ( C) Differential Pressure: F ( C) Maximum Reverse Differential Pressure: F ( C) Recommended change-out pressure: 35 psid (2.4 bar) Sterilization: Cartridges may be autoclaved for 30 minutes at 250 F (121 C) under no end load conditions. May be in-line sanitized one time only in forward flow direction with 185 F (85 C) hot water do not exceed 3 psid. Conventional pleated polypropylene filter media such as QMA, PMA and PMC QXL filter media Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. European Directive for Direct Food Contact - European Regulations No 1935/2004 and European directive 82/711/EEC: Tested for migration behavior in direct food contact. Minimal rinse required for use. Data available upon request. Typical Applications CMP P-O-U and bulk slurries Adhesives Paints Beverages Coatings Inks 38

45 Pleated Filters QXL Nomenclature Information QXL 5-10 P8 S Filter Type QXL Series Filters Retention Rating (microns) 0.45* 5 0.5** Example: QXL 5-10P8S * Special CMP slurry formulation. ** Special ink formulation. Differential Pressure BAR PSI Nominal Length (inches) QXL FLOW RATE Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) 0.45 μm LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End AM Single open end, internal O-Ring NPC Double open end, internal O-Ring 0.5 μm 1 μm 3 μm 5 μm 10 μm 20 μm 40 μm USGPM Removal Efficiency Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) Beta Ratio Beta 1000 Beta 100 Beta 50 Efficiency 99.9% 99% 98% 0.45 micron micron micron microns microns microns microns microns Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 3 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Pleated Filters Customer Service: International Customer Service :

46 Filtration Separation Purification 40

47 Depth Filters Graver Product Type Media Hardware Retention Ratings (μm) Efficiency COAX Polypropylene Polypropylene 0.5, 1, 3, 5, 10, 25 Nominal Bicomponent/Melt Blown Polyethylene Coreless Crystal MBF Polypropylene Polypropylene 1, 3, 5, 10, 20, 30, 50, 75 Nominal Melt blown Fiber Core MBC Polypropylene Polypropylene 1, 3, 5, 10, 20, 30, 50, 75 Nominal Melt blown Molded Core Stratum A Polypropylene Polypropylene 0.5, 1, 3, 5, 10, 20, Absolute Melt blown Molded Core 30, 50, 70 Beta 1000 Depth Filters Stratum C Polypropylene Polypropylene 0.5, 1, 3, 5, 10, 20, Nominal Melt blown Molded Core 50, 75 Beta 10 Customer Service: International Customer Service :

48 Filtration Separation Purification COAX Series Filter Cartridges Two Stage Depth Filter Cartridge The COAX Depth Filter cartridge is an integral two stage depth filter. The first stage is made of nonwoven melt blown polypropylene to trap coarser particles. The second stage is composed of a bicomponent polypropylene and polyethylene fiber to provide fine particle retention. This unique design provides a true graded, two zone structure that offers a marked increase in useful life and dirt capacity. In addition, the rigid nature means there is no flexing of the cartridge and greatly reducing media migration and particle unloading. Features Benefits Two stage depth filter Maximum dirt holding and useful life Inert pure polyolefin construction, non-shedding media Broad chemical compatibility Low extractables Extensive range of lengths and configurations Rigid construction resists unloading Product Specifications Media: Thermally bonded Polypropylene/polyethylene fiber End caps: Polypropylene (when used) Gaskets/O-Rings : Silicone, EPDM, Buna N, Santoprene, Viton, Teflon encapsulated Viton (O-Rings only) Micron ratings: 0.5, 1, 3, 5, 10, 25 μm Dimensions Nominal lengths: 5", 9.75", 10", 20", 30", 40" (12.7, 24.8, 25.4, 50.8, 76.2, cm) Outside diameter: 2.6" (6.5 cm) Inside diameter: 1.0" (2.54 cm) Operating Parameters Maximum operating 140 F (60 C) Maximum F (7 21 C) differential pressure: F ( C) Recommended change-out pressure: 35 psid (2.4 bar) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. Typical Applications Paint Perfumes Cutting Oils CMP Slurries Magnetic Slurries Corn Syrup Plating Solutions Pre R.O. Coatings Performance Specifications Sanitization Hot water at 176 F (80 C) at 2 psid (0.14 bar) for 30 min. In-line steam at 257 F (125 C) at 1psid (0.07 bar) for 30 min. Autoclavable at 257 F (125 C) for 30 min. 42

49 Depth Filters COAX Nomenclature Information COAX RL P3 B COAX Series Filters Retention Rating (microns) Nominal Length (inches) Length Option Blank Standard length RL Reduced length Example: COAX 25-40RLP3B End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P6 Self-Seal Spring on One End P7 226/Fin Single Open End P8 222/Fin Single Open End PX Extended Core N None (Cut Ends) AM Single Open End, internal O-Ring DBG Direct Bond Santoprene Gaskets Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) N None Differential Pressure COAX FLOW RATE Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI μm μm μm 5 μm μm 25 μm USGPM Removal Efficiency Beta Ratio Beta 10 Beta 20 Beta 100 Efficiency 90% 95% 99% 0.5 micron micron microns microns microns microns Depth Filters LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Customer Service: International Customer Service :

50 Filtration Separation Purification CrystalMBFSeries Filter Cartridges Melt Blown Filters An economical, disposable, filter element that can be used in a wide range of applications. The Crystal MBF depth filter is constructed of 100% polypropylene media for chemical compatibility with a variety of process fluids. The unique Crystal Core prevents collapse even at elevated temperatures. Features Benefits Available in nominal ratings from 1 to 75 microns Formed Crystal Core for excellent collapse strength Graded pore construction for long on-stream life Melt blown media resists dirt unloading as differential pressure increases Non-shedding High dirt holding capacity Economical depth filtration Thermal bonded endcaps optional Free of binders, adhesives and surfactants Highly consistent performance Product Specifications Media: Polypropylene End caps/center core: Polypropylene Gaskets/O-Rings: Silicone, EPDM, Buna N, Santoprene, Viton, Teflon encapsulated Viton (O-Rings only) Micron ratings: 1, 3, 5, 10, 20, 30, 50, 75 μm Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. NSF 61 - Certified to NSF/ANSI STD 61 for materials requirements only - Component.* Dimensions Nominal lengths: 9.75", 10", 20", 30", 40", 50" (24.8, 25.4, 50.8, 76.2, 101.6, 127 cm) Other lengths available Outside diameter: 2.5" (6.35 cm), 2.63" (6.7 cm) Endcapped Inside diameter: 1.1" (2.79 cm) Operating Parameters Maximum differential F ( C) pressure: F ( C) F ( C) Recommended changeout differential pressure: 35 psid (2.4 bar) *NSF61 applies to NN, P6 and PX styles only. Typical Applications RO Prefilters Wastewater Food & beverage Chemicals Blowdown post filter Rad waste Aqueous solutions Inks Outer prefilter zone Inner prefilter zone Final prefilter zone Final filtration zone 44

51 Depth Filters Crystal MBF Nomenclature Information CMBF N N -BB Filter Type Crystal MBF Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P6 Self-Seal Spring on One End P7 226/Fin Single Open End P8 222/Fin Single Open End PX Extended Core N None (Cut Ends) DBG Direct Bond Santoprene Gaskets Blank -BB Individually bagged Single bulk bag Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) N None Example: CMBF 10-20NN-BB Crystal MBF FLOW RATE Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI 1 μm 3 μm 5 μm 10 μm μm μm 50, 75 μm USGPM Depth Filters LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Customer Service: International Customer Service :

52 Filtration Separation Purification MBC Series Filter Cartridges Melt Blown Filters An economical, disposable, filter element that can be used in a wide range of applications. The MBC depth filter is constructed of 100% polypropylene media for chemical compatibility with a variety of process fluids. The molded core prevents collapse even at elevated temperatures. Features Benefits Available in nominal ratings from 1 to 75 microns Molded core for excellent collapse strength Graded pore construction for long on-stream life Melt blown media resists dirt unloading as differential pressure increases Non-shedding High dirt holding capacity Economical depth filtration Thermal bonded endcaps optional Free of binders, adhesives and surfactants Product Specifications Media: Polypropylene End caps/center core: Polypropylene Gaskets/O-Rings: Silicone, EPDM, Buna N, Santoprene, Viton and Teflon encapsulated Viton (O-Rings only) Micron ratings: 1, 3, 5, 10, 20, 30, 50, 75 μm Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. NSF 61 - Certified to NSF/ANSI STD 61 for materials requirements only - Component.* Dimensions Nominal lengths: 9.75", 10", 20", 30", 40" (24.8, 25.4, 50.8, 76.2, cm) Other lengths available Outside diameter: 2.5" (6.35 cm), 2.63" (6.7 cm) Endcapped Inside diameter: 1.0" (2.54 cm) Operating Parameters Maximum differential F ( C) pressure: F ( C) F ( C) Recommended changeout differential pressure: 35 psid (2.4 bar) *NSF61 applies to NN, P6 and PX styles only. Typical Applications RO Prefilters Wastewater Food & beverage Chemicals Blowdown post filter Rad waste Aqueous solutions Inks Outer prefilter zone Inner prefilter zone Final prefilter zone Final filtration zone 46

53 Depth Filters MBC Nomenclature Information MBC N N Filter Type MBC Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P6 Self-Seal Spring on One End P7 226/Fin Single Open End P8 222/Fin Single Open End PX Extended Core N None (Cut Ends) DBG Direct Bond Santoprene Gaskets Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) N None Example: MBC 10-20NN MBC FLOW RATE Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI μm 3 μm 5 μm 10 μm 20 μm 30 μm 50 μm 75 μm USGPM Depth Filters LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Customer Service: International Customer Service :

54 Filtration Separation Purification Stratum A Series Filter Cartridges Absolute Rated Melt Blown Filters Stratum A Series melt blown depth filters deliver 99.9% efficiency at the stated micron for the most demanding applications. By utilizing ultra fine fibers and controlled thermal bonding, the Stratum A series retains captured contaminant even at higher differential pressures. Features - Benefits Absolute retention ratings from 0.5 to 70 microns Multi-zone melt blown depth filter with a graded pore structure for maximum dirt holding capacity Thermally bonded fibers for high void volume and long on-stream life Lot traceable filters come with certificate of conformance. 100% pure virgin polypropylene Molded center core for higher temperature and pressure capability Free of surfactants, binders and adhesives Product Specifications Media: Polypropylene End caps/center core: Polypropylene Gaskets/O-Rings: Silicone, EPDM, Buna N, Santoprene, Viton, Teflon encapsulated Viton (O-Rings only) Micron ratings: 0.5, 1, 3, 5, 10, 20, 30, 50, 70 μm Dimensions Nominal lengths: 4", 5", 9.75", 10", 19.5", 20", 29.25", 30", 39", 40" (10.2, 12.7, 24.8, 25.4, 49.5, 50.8, 74.3, 76.2, 99.1, cm) Outside diameter: Inside diameter: 2.5" (6.35 cm) 1" (2.54 cm) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. NSF 61 - Certified to NSF/ANSI STD 61 for materials requirements only - Component.* Outer prefilter zone Operating Parameters Maximum differential F ( C) pressure: F ( C) F ( C) Recommended changeout differential pressure: 35 psid (2.4 bar) Steam Sterilization: Stratum single open end style filters may be autoclaved under no end load conditions for 30 minutes at 121 C. Filters should be cooled to normal operating temperatures prior to use. *NSF61 applies to NN, P6 and PX styles only. Typical Applications Chemicals Pharmaceuticals Paint/Inks Food and beverages Water Microelectronics Plating Cosmetics Inner prefilter zone Final prefilter zone Final filtration zone 48

55 Depth Filters Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) 0.5 μm 1 μm 3 μm 5 μm 10 μm BAR PSI Stratum A FLOW RATE 20 μm 30 μm 50 μm 70 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Stratum A Nomenclature Information STA P2 T Filter Type STA - Stratum A Series Filters Retention Rating (microns) Example: STA NN Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P6 Self-Seal Spring on One End P7 226/Fin Single Open End P8 222/Fin Single Open End PX Extended Core N None (Cut Ends) DBG Direct Bond Santoprene Gaskets AM Single open end, internal O-Ring NPC Double open end, internal O-Ring Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) N None Removal Efficiency Micron Rating 99.9% 99% 90% Beta Ratio Beta 1000 Beta 100 Beta micron micron micron micron micron micron micron micron micron Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 3 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. Depth Filters Customer Service: International Customer Service :

56 Filtration Separation Purification Stratum C Series Filter Cartridges High Performance Filters For critical customer applications requiring precise and repeatable depth filtration, the Graver Stratum C series melt blown filters deliver exceptional performance. With a multi- zoned construction, true clarifying filtration is achieved with no unloading of captured contaminant. Features - Benefits Multi-zone melt blown depth filter with a true graded pore structure Thermally bonded fibers for high void volume and long on-stream life Available in precise 90% removal efficiencies from 0.5 to 75 microns 100% pure virgin polypropylene Molded center core for higher temperature and pressure capability Free of surfactants, binders and adhesives Product Specifications Media: Polypropylene End caps/center core: Polypropylene Gaskets/O-Rings: Silicone, EPDM, Buna N, Santoprene, Viton, Teflon encapsulated Viton (O-Rings only) Micron ratings: 0.5, 1, 3, 5, 10, 20, 50, 75 μm Dimensions Nominal lengths: 4", 5", 9.75", 10", 19.5", 20", 29.25", 30", 39", 40" (10.2, 12.7, 24.8, 25.4, 49.5, 50.8, 74.3, 76.2, 99.1, cm) Outside diameter: Inside diameter: 2.5" (6.35 cm), 2.63" (6.7 cm) Endcapped 1" (2.54 cm) Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, and , as applicable for food and beverage contact. NSF 61 - Certified to NSF/ANSI STD 61 for materials requirements only - Component.* Outer prefilter zone Operating Parameters Maximum differential F ( C) pressure: F ( C) F ( C) Recommended changeout differential pressure: 35 psid (2.4 bar) Steam Sterilization: Stratum single open end style filters may be autoclaved under no end load conditions for 30 minutes at 121 C. Filters should be cooled to normal operating temperatures prior to use. *NSF61 applies to NN, P6 and PX styles only. Typical Applications Chemicals Pharmaceuticals Paint/Inks Food and beverages Water Microelectronics Plating Cosmetics Inner prefilter zone Final prefilter zone Final filtration zone 50

57 Depth Filters Stratum C Nomenclature Information STC 5-10 P3 V Filter Type STC - Stratum C Series Filters Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P6 Self-Seal Spring on One End P7 226/Fin Single Open End P8 222/Fin Single Open End PX Extended Core N None (Cut Ends) DBG Direct Bond Santoprene Gaskets AM Single open end, internal O-Ring Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) N None Example: STC 5-10P3V Stratum C FLOW RATE Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) 0.5 μm 1 μm 3 μm 5 μm BAR PSI μm 20 μm 50 μm 75 μm USGPM Depth Filters LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Customer Service: International Customer Service :

58 Filtration Separation Purification 52

59 Specialty Filters Graver Product Type Media Hardware Retention Ratings (um) Efficiency GSTACK Modules Cellulose with Polypropylene 0.25 to 15 Nominal Lenticular DE or Perlite RTEC P Acrylic/Phenolic Polyester 5, 10, 25, 50, 75, 100 Nominal Resin bonded available Steris Replacement PES membrane or Polypropylene 0.2 Nominal or Pleated polypropylene sheet Absolute TPM Titanium Titanium 0.5, 2, 5, 10, 15, 35 Nominal Sintered Powder Metal Beta 200 Specialty Customer Service: International Customer Service :

60 Filtration Separation Purification GSTACK Series Filter Modules Lenticular Depth Filter Modules GStack Series depth filter modules are designed in a lenticular format for fluid clarification applications. Consisting of either cellulose with diatomaceous earth or cellulose with perlite, a formulation is available to achieve excellent particle and haze removal. Grades are also available with water absorbing capability or that meet pharmaceutical requirements. Features Benefits Proven performance cellulose based filter sheet media Choice of DE or perlite filter aids Nominal retention ratings from 0.25 to 15 microns High efficiency due to positive zeta potential Exceptional mechanical strength Choice of flat gasket seal or double o-ring seal Choice of economical stainless steel bands or rigid molded polypropylene core Special water absorbing component is available in the 10 and 15 micron grades Steam sterilizable Media grade stamped on sheets for easy identification Product Specifications Media/Microns (nominal): Cellulose/DE , 0.3, 0.5, 0.8, 1.0, 2.5, 5, 10 Cellulose/Perlite - 0.5, 1.0, 2.5, 5, 10, 15 Water absorbing - 10, 15 Hardware: End caps & cell edge seals - Polypropylene Center support - Stainless steel bands or polypropylene core O-Rings: Buna-N, Silicone, EPDM, Viton, Teflon Filtration Area: 12"/16 cell sq ft (1.7 sq m) 16"/16 cell - 40 sq ft ( 3.7 sq m) 12"/14 cell water absorbing grade sq ft (1.5 sq m) Dimensions Nominal diameter: 12 or 16 (287 mm, 405 mm) # of Cells per stack 16 (14 for water absorbing grade) Height: 10 7/8 (276 mm) Certifications USP Class V - Meets USP Class V Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Section , as applicable for food and beverage contact. Typical Applications Wine/Beer Sweeteners Silicone oils Cosmetics Adhesives Pharmaceuticals Flavors/Fragrances Edible oils Distilled spirits Operating Parameters Maximum operating temperature: 176 F (80 C) Maximum differential pressure: 35 psid (2.4 bar) Steam in place: 266 F (130 C) for 30 minutes at 25 psid maximum (1.7 bar) Hot water 176 F (80 C) for 30 minutes sanitization: at up to 14 psid (1 bar) 54

61 Specialty Filters Diameter 2 12" 6 16" GSTACK Nomenclature Information GS 2 16 D2.5 P C B Filter Type GSTACK Series Filters Cells (W grade) Core/End Style S SS bands C PP core/flat gasket O PP core/o-ring Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon Media Cellulose/DE Cellulose Water Perlite Absorbing * D0.25 L0.3 W10 D0.3 L0.5 W15 D0.5 L1 D0.8 L2.5 D1 L5 D2.5 L10 D5 L15 D10 Example: GS 216D2.5PCB Grade Blank P Industrial Pharmaceutical * Water grade is only available in 12" with SS bands. GSTACK Flow Rate Media Grade Nominal Retention Practical Water Flow Rate (GPM) Cellulose/DE Cellulose/Perlite Water Absorbing Rating (microns) 12", 16 cell 16", 16 cell Water Absorbing 12" D D0.3 L D0.5 L D D1 L D2.5 L D5 L D10 L10 W L15 W NOTE: Flow rate applies to water at 70 F at 1 psid clean differential. For different fluid characteristics, testing is highly recommended for proper sizing. Specialty Customer Service: International Customer Service :

62 Filtration Separation Purification RTEC P Series Filter Cartridges Rigid Resin Bonded Filters RTEC P Series filters feature an polyester fiber/phenolic resin construction that produces an extremely rigid pore structure. This construction allows the filter to withstand extremes of viscosity and temperature without compression or collapse. In addition, a true graded density construction allows complete utilization of the filter s depth, with coarse particles captured in the outer zones and finer particles captured nearer the core. Features Benefits Rigid polyester fiber/phenolic resin construction prevents unloading even at high differential pressures Grooved outer surface increases surface area for longer on-stream life Available in a wide range of removal efficiencies from 1 to 100 microns Available with optional end configurations for installation in most housings No metal or plastic cores for easier disposal Broad chemical compatibility Product Specifications Media: Polyester Fiber/Phenolic Resin Optional End Caps: Polyester Multi length bonding agent: Polyamide Hot Melt Gaskets/O-Rings: Buna-N, EPDM, Silicone, Viton, Teflon Encapsulated Viton (O-Rings only) Micron ratings: 1, 5, 10, 25, 50, 75, 100 μm Dimensions Nominal lengths: 9.75", 10" 19.5", 20", 29.25", 30", 39", 40" (24.8, 25.4, 49.5, 50.8, 74.3, 76.2, 99.1, cm) Outside diameter: 2.45" (6.22 cm) Inside diameter: " (25-28 mm) tapered Operating Parameters Maximum operating F (5.2 bar 20 C) temperature: * F (1.0 bar 93 C) for lengths >10 with glued segments 20 psid 220 F (1.4 bar 104 C) for 10 lengths 200 F (93 C) in gas Recommended change-out pressure: 35 psid (2.4 bar) Typical Applications * Paints, Inks Sealants Adhesives Lacquers, Varnishes, Shellacs Fuel Oils, Crude Oils, Grease Machine Coolants Silicones Antifreeze Plasticizers Animal Oils * Always check compatibility with the specific process fluid at the specific application temperature. 56

63 Specialty Filters RTEC P Nomenclature Information RTEC P 5-20 N N Filter Type RTEC P Series Filters Retention Rating (microns) Example: RTEC P 5-20NN Nominal Length (inches) End Configuration P Double Open End P2 226/Flat Single Open End P3 222/Flat Single Open End P7 226/Fin Single Open End P8 222/Fin Single Open End N None Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) N None Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) 1 μm 5 μm BAR PSI RTEC P FLOW RATE 10 μm 25 μm 50 μm 75 μm 100 μm USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Note: For chemical compatibility, flow rates, and temperature requirements please consult the factory or your local Graver distributor. Specialty Customer Service: International Customer Service :

64 Filtration Separation Purification Steris Replacement Series Filter Cartridges Graver Technologies replacement A and B filters, for Steris machines offer excellent protection for the final sterile filter. Features Benefits Replacement A & B filters are designed to effectively protect and extend the life of the final sterile filter Choice of endcap styles to fit your housings Meets FDA Standards All material used in the construction of the filters meets FDA (Food and Drug Administration) Title 21 of the CFR Clean manufacturing process is used which eliminates the use of glues or epoxies End caps are thermo-bonded to the media and support hardware High dirt holding capacity Longer on-line service reduces valuable maintenance time Fixed pore construction eliminates dirt unloading or fiber releasing Product Specifications - Steris "A" Replacement Media: Polypropylene Inner core, end caps, cage: Polypropylene Gaskets/O-Rings: Silicone Nominal micron rating: 0.2 μm Certifications USP Class VI - Meets USP Class VI Biological Test for Plastics. FDA Listed Materials - All Materials comply with FDA Title 21 of the Code of Federal Regulations Sections 174.5, , and as applicable for food and beverage contact. Product Specifications - Steris "B" Replacement Media: Polyethersulfone membrane Inner core, end caps, cage: Polypropylene O-Rings: Silicone or EPR Absolute micron rating: 0.2 μm Dimensions Nominal length: Nominal outside diameter: Inside diameter: Surface area: 9.8" (24.9 cm) DOE 2.7" (6.9 cm) 1.0" (2.54 cm) 4.4 ft 2. (0.41 m 2 ) for SOE 5.1 ft 2. (0.47 m 2 ) for DOE Dimensions Nominal length: 10.8" (27.4 cm) SOE Nominal outside diameter: 2.7" (6.9 cm) Inside diameter: 1.0" (2.54 cm) Surface area: 7 ft 2. (0.56 m 2 ) Operating Parameters Maximum operating temperature: 175 F (80 C) Maximum differential pressure: F ( C) Nominal flow rates: 6 GPM/psid (22 LPM/0.07 bar) Operating Parameters Maximum operating temperature: 180 F (82 C) Maximum differential pressure: F ( C) Nominal flow rates: 2.15 GPM/psid (8.1 LPM/0.07 bar) 58

65 Specialty Filters Steris Replacement Filter Specifications WATER SUPPLY VALVE PRESSURE RELEASE BUTTON PRESSURE RELEASE BUTTON HOUSING BODY A A B FLOW HOUSING BODY B GASKET PREFILTER A (Illustration depicts a double open ended option) TWO O RINGS PREFILTER B HOUSING BOWL A GASKET HOUSING BOWL B Steris "A" Replacement Filter Steris "B" Replacement Filter Note: For chemical compatibility, flow rates, and temperature requirements please consult the factory or your local Graver distributor. Steris Replacement Configuration Options Part Number Description "A" Filter "B " Filter FPLGT00100 F FPLGT00200 F80D Double open end with silicone flat gasket seal. Single open end with internal 214 silicone O-Ring. Recessed cup on closed end to fit over housing post. Single open end with silicone O-Rings. Flat cap on closed end. Single open end with EPR O-Rings. Recessed cup on closed end to fit over housing post. Specialty Customer Service: International Customer Service :

66 Filtration Separation Purification TPM Series Filter Cartridges Titanium Porous Metal Technology TPM series filters are porous titanium filters designed for applications involving heat, gases, aggressive chemicals, cryogenics or polymers. Made from titanium powder, that is sintered to form a rugged, fixed pore structure, TPM filters are made to withstand temperature extremes, high pressures and repeated cleaning/backwash cycles. There are no longitudinal seams, for improved mechanical strength and corrosion resistance. TPM filters are produced in a range of configurations and micron ratings to perform in a variety of liquid and gas applications. Features Benefits Constructed entirely of sintered titanium powder Offers high corrosion resistance Cleanable/Backwashable Allows for re-use Maximum economy High Temperature Sintering No media migration Various gasket/o-ring materials and configurations Easily retrofits most systems Product Specifications Media: Titanium End caps: Titanium Gaskets/O-Rings: EPR, Buna-N, Viton, Teflon Encapsulated Viton (O-Rings only), Teflon (gasket only) Micron ratings: 0.5, 2, 5, 10, 15, 35 μm Dimensions Nominal lengths: 10, 20, 30 (25.4, 50.8, 76.2 cm) Outside diameter: 2.75 (70 mm) or 2.36 (60 mm) Operating Parameters Maximum operating 700 F (371 C)* Maximum 250 psid (17.4 bar) forward) differential pressure: 50 psid (3.5 bar) reverse Recommended change-out pressure: 35 psid (2.4 bar) Typical Applications Corrosive liquids and gases Cryogenic fluids High viscosity solutions Process steam High temperature liquids and gases Catalyst recovery * Max temperature applicable to NPT style filters only (No O-Rings or gaskets). Consult Graver Technologies for guidance on specific chemical/temperature compatibility. 60

67 Specialty Filters TPM Nomenclature Information TPM S M1 N Filter Type TPM Series Filters Diameter Option Blank 2.75" diameter S Slim 2.36" diameter Retention Rating (microns) Nominal Length (inches) End Configuration P Double Open End * P2 226/Flat Single Open End P3 222/Flat Single Open End M1 3 4 Inch MNPT Threads M2 1 Inch MNPT Threads Gasket or O-Ring S Silicone B Buna-N E EPDM V Viton T Teflon encap. Viton (O-Rings only) T Teflon (gasket only) N None Example: TPM S10-30M1N Removal Efficiency Beta Ratio Beta 200 Beta 20 Beta 10 Efficiency 99.5% 95% 90% 0.5 micron 0.5 micron 0.3 micron 0.1 micron 2 microns 2 micron 0.8 micron 0.4 microns 5 microns 5 micron 3 microns 1 microns 10 microns 10 microns 8 microns 5 microns 15 microns 15 microns 12 microns 10 microns 35 microns 35 microns 32 microns 28 microns Differential Pressure TPM 2.36" (60 mm) FLOW RATE Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI 0.5 μm 2 μm 5 μm μm μm 35 μm USGPM Beta Ratio = Upstream particle counts Downstream particle counts The micron ratings shown at various efficiency and beta ratio value levels were determined through laboratory testing, and can be used as a guide for selecting cartridges and estimating their performance. Under actual field conditions, results may vary somewhat from the values shown due to the variability of filtration parameters. Testing was conducted using the single-pass test method, water at 2.5 gpm/10'' cartridge. Contaminant's included latex beads, coarse and fine test dust. Removal efficiencies were determined using dual laser source particle counters. *Note: DOE style is not compatible with SCB housings LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Differential Pressure Typical Flow Rate Clean Water at Ambient Temperature (per 10''cartridge) BAR PSI 0.5 μm 2 μm 5 μm TPM 2.75" (70 mm) FLOW RATE 1 10 μm 15 μm 35 μm Specialty USGPM LPM For liquids other than water, multiply pressure drop by the fluid viscosity in centipoise Customer Service: International Customer Service :

68 Filtration Separation Purification 62

69 Filter Housings Code or Material of Cartridge End Number Max Operating Graver Product Non-Code Construction Configuration of Filters Pressure (psig/bar) GSTACK Code & 316L DOE or 1, 2, 3, 4 100/6.9 Non-Code Double O-ring High Flow Code & 304, 316, Special 1, 3, 4, 7 150/10.3 Non-Code and Carbon Steel Quad Seal IHP Non-Code 316L SS DOE, 222, 226 1, 3, 5, 7, 125 or 200/8.6 12, 21 or 13.8 LPF Non-Code 304L or 316L SS DOE, 222, 226 3, 5, 7, 150/ , 21 MC Non-Code 304L or 316L SS DOE 4, 5, 7, 12, 150/ , 36, 52 SC Non-Code 304L or 316L SS DOE or or 300/17.2 or 20.7 SHP Non-Code 316L SS DOE, 222, 226 1, 3, 5, or 200/8.6 or 13.8 Custom Code & Call Factory Non-Code Housings Customer Service: International Customer Service :

70 Filtration Separation Purification GSTACK Series Filter Housings Lenticular Depth Filter Housings Sanitary Housing, designed for use with Graver GSTACK Series Depth Filter Modules. GSTACK housings feature highly polished finish, sanitary fittings, vent connection, and no internal threads to meet the needs of high purity applications. The vertical configured housings are constructed of all 316L SS materials as standard in sizes to hold from 1 to 4 modules. The split dome in the 3 and 4 high allow flexibility to run different number of modules and also facilitates complete cleaning when disassembled. Features Benefits Accepts flat gasket or o-ring style lenticular filter elements Select from 2 diameters to accept either 12" or 16" modules 316L stainless steel with 180 grit finish 1.5" Sanitary tri-clamp Inlet & Outlet with 90 deg elbows Split dome for size flexibility and easy cleaning 0-60 psi stainless steel non-sanitary gauge V-Band Clamp Closure 60 PSIG Design Pressure EPDM Elastomers/Gaskets Non-Adjustable Legs with foot pads Top Vent Product Specifications Construction: 316 L Stainless Steel wetted parts Shell Gasket Standard: EPDM Optional Gaskets: Buna-N, Neoprene, Viton, Silicone, Teflon Encapsulated Silicone Operating Parameters Maximum operating 100 psig (6.9 pressure: 200 F (93 C) in aqueous solutions 175 F (79 C) for oil based solutions Flow Rate: 1 GPM/ft 2 of media surface area Available Options Electropolish or <30 Ra polish for liquid contact parts ASME Code available Drains Typical Applications Pharmaceuticals Chemicals Cosmetics Food and beverage 64

71 Housings GSTACK Housing Nomenclature Information GSH FG TC1.5 E -EP Model GSTACK Series Module Diameter 12 12" 16 16" Example: GSH 1203FGTC1.5E-EP # of Modules Adapter Style OR O-Ring FG Flat gasket Inlet/Outlet TC " Tri-clamp (for 12") TC2 2" Tri-clamp (for 16") Gasket S Silicone B Buna-N E EPDM V Viton N Nitrile T Teflon encap. silicone Options EP Electropolished D Drain G Pressure gauge Model * Based on 16 cell pack. Dimensions include support legs. GSTACK Housing Specifications Height Base Width Weight Empty Filter Area* (in) (mm) (in) (mm) (lbs) (kg) (ft 2 ) (m 2 ) GSH GSH GSH GSH GSH GSH GSH GSH Housings Customer Service: International Customer Service :

72 Filtration Separation Purification High Flow Series Filter Housings Filter Housings for High Flow Applications Graver High Flow Series filter housings are designed to accept Graver and competitive High Flow Series large geometry filter elements. Available in both vertical and horizontal orientations, the High Flow housings can accept from 1 to 7 filter elements. Also available is a single round tipped horizontal design that allows easier removal without the need for a platform and readily drains from back of vessel to eliminate fluid spills. Features Benefits Industrial grade housings available in 304, 316 and carbon steel wetted parts ASME U code available Designs for 1, 3, 4 or 7 filters per housing for flows up to 3500 GPM* 150 psig designs Accepts 20", 40" and 60" High Flow cartridges Vertical and horizontal designs offered Hold down plate prevents elements from unseating due to back pressure Filter removal tool available to facilitate element changeout Swing bolts on 150 psig design Equipped with 1" vent and 2" drain (1" drain on tipped horizontal style). Product Specifications Shell O-ring Buna N, Viton, EPDM, Silicone Optional 300 psig (20.6 bar) Flanged Head designs available Consult Factory Not for use with compressed gases Operating Parameters Maximum operating pressure: Carbon Steel 150 psig ( F (260 C) in liquid service Stainless Steel 150 psig ( F(149 C) in liquid service Not for use with compressed gases Note: 1. Flow capacity based on light dirt load and low viscosity. Actual flow rate may be lower with vessel sizing based on fluid dirt loads, nature of contaminant, viscosity, micron rating and temperature. Available Options Vertical Housing Inlet/outlet Side in/side out, Side in/bottom out Horizontal Housing Inlet/Outlet Side in/bottom out Tilted Horizontal Side in/side out, Side in/bottom out Gauge ports Hinged cover Davit arm Typical Applications Pre RO Water Desalination Food and Beverage Pulp and Paper Oil and Gas Petrochemicals 66

73 Housings HFH Nomenclature Information HFH 1 H 40 T 4 SS 150 -S -H Model HFH Series # of Filters Example: HFH 1H40T4SS150-S-H Orientation V Vertical H Horizontal HT Tipped Horizontal (1 round only) Cartridge Height (inches) 20, 40, 60 Material of Construction R 304L SS C Carbon Steel T 3016L SS Inlet/Outlet Size 4, 6, 8, 12 Inlet/Outlet Config. SS Side in/side out SB Side in/bottom out Pressure Rating psig psig (consult factory) Gasket B Buna-N S Silicone E EPDM V Viton Options H Hinge DA Davit arm 6 HFH Pressure Drop for various Pipe Sizes Pressure Drop (psid) Flow Rate (GPM, Water) Model Rate Flow Capacity GPM (LPM) HFH Dimensional Data - Horizontal/Swing Bolt No. 10" Filter Elements Lengths Dim. "A" inches (cm) Dim. "B" inches (cm) Dim. "C" 1 inches (cm) Dim. "D" 1 inches (cm) Dim. "E" inches (cm) Dim. "F" 1 inches (cm) Max. Flange size (in) Drain Vent Gauge HFH 3H (3975) " (203) " (30) " (155) 18" (46) 44" (112) 15" (38) 8 2" NPT 1" NPT 1 4" NPT HFH 4H (5300) " (204) " (30) " (155) 20" (51) 46" (117) 16" (41) 8 2" NPT 1" NPT 1 4" NPT HFH 7H (9275) " (233) " (39) 68" (173) 24" (61) 48" (122) 18" (46) 12 2" NPT 1" NPT 1 4" NPT HFH 1H (1893) " (216) 8" (20) 73" (185) 8 5 8" (22) 40" (102) 9" (23) 4 2" NPT 1" NPT 1 4" NPT HFH 3H (5680) " (253) " (30) " (206) 18" (46) 44" (112) 15" (38) 8 2" NPT 1" NPT 1 4" NPT HFH 4H (7570) " (255) " (30) " (206) 20" (51) 46" (117) 16" (41) 8 2" NPT 1" NPT 1 4" NPT HFH 7H (13248) " (284) " (39) 88" (224) 24" (61) 48" (122) 18" (46) 12 2" NPT 1" NPT 1 4" NPT Notes: 1. Dimensions are based on the maximum connection sizes. 2. Dimensions include support legs. 3. Dim. "A" will increase by approx. 3" for S.S. swing bolt housings. HFH Housing Dimensional Drawing Horizontal Swing Bolt Design F B A C D E Housings Customer Service: International Customer Service :

74 Filtration Separation Purification Model Rate Flow Capacity GPM (LPM) No. 10" Elements Filter Lengths HFH Dimensional Data - Vertical/Swing Bolt Dim. "A" inches (cm) Dim. "B" inches (cm) Dim. "C" 1 Dim. "D" 1 inches (cm) inches (cm) Dim. "E" Dim. "F" 1 inches (cm) inches (cm) Dim. "G" inches (cm) Max. Flange size (in) Drain Vent Gauge HFH 1V (662) " (132) 48" (122) 40" (102) 28" (71) 12" (30) 8 5 8" (22) 18" (46) 4 2" NPT 1" NPT 1 4" NPT HFH 3V (1986) " (162) " (144) 45" (114) 28" (71) 12" (30) 18" (46) 30" (76) 8 2" NPT 1" NPT 1 4" NPT HFH 1V (1325) " (183) 68" (173) 60" (152) 48" (122) 12" (30) 8 5 8" (22) 18" (46) 4 2" NPT 1" NPT 1 4" NPT HFH 3V (3975) " (212) " (195) 65" (165) 48" (122) 12" (30) 18" (46) 30" (76) 8 2" NPT 1" NPT 1 4" NPT HFH 4V (5300) " (214) " (195) 65" (165) 48" (122) 12" (30) 20" (51) 32" (81) 8 2" NPT 1" NPT 1 4" NPT HFH 7V (9275) " (244) " (222) 72" (183) 52" (132) 12" (30) 24" (61) 36" (91) 12 2" NPT 1" NPT 1 4" NPT Notes: 1. Dimensions are based on the maximum connection sizes. 2. Dimensions include support legs. 3. Dim. "A" will increase by approx. 3" for S.S. swing bolt housings. HFH Housing Dimensional Drawing Vertical Swing Bolt Design G OVERHEAD CLEARANCE EQUALS LENGTH OF ELEMENT F A B C D E Model HFH Dimensional Data - Horizontal Tipped (Side in/side out, Swing Bolt) Rate Flow Capacity GPM (LPM) No. 10" Filter Elements Lengths Dim. "A" inches (cm) Dim. "B" inches (cm) Dim. "C" inches (cm) Dim. "D" inches (cm) Dim. "E" 1 inches (cm) Max. Flange size (in) Drain Vent Gauge HFH 1HT (662) " (46) " (60) 8" (20) 16" (41) " (103) 4 1" NPT 1" NPT 1 4" NPT HFH 1HT (1325) " (46) " (77) 8" (20) 36" (91) " (154) 4 1" NPT 1" NPT 1 4" NPT HFH 1HT (1986) " (46) " (94) 8" (20) 56" (142) " (204) 4 1" NPT 1" NPT 1 4" NPT Notes: 1. Dim. "E" will increase by approx. 3" for S.S. swing bolt housings. HFH Housing Dimensional Drawing 1-Around Tilted Horizontal Side in/side out Swing Bolt Design C E D B A 68

75 Housings Model HFH Dimensional Data - Horizontal Tipped (Side in/bottom out, Swing Bolt) Rate Flow Capacity GPM (LPM) No. 10" Filter Elements Lengths Dim. "A" inches (cm) Dim. "B" inches (cm) Dim. "C" inches (cm) Dim. "D" inches (cm) Dim. "E" 1 inches (cm) Max. Flange size (in) Drain Vent Gauge HFH 1HT (662) " (30) " (81) 8" (20) " (85) " (115) 4 1" NPT 1" NPT 1 4" NPT HFH 1HT (1325) " (30) " (98) 8" (20) " (136) " (166) 4 1" NPT 1" NPT 1 4" NPT HFH 1HT (1986) " (30) " (116) 8" (20) " (187) " (217) 4 1" NPT 1" NPT 1 4" NPT Notes: 1. Dim. "E" will increase by approx. 3" for S.S. swing bolt housings. HFH Housing Dimensional Drawing 1-Around Tilted Horizontal Side in/bottom out Swing Bolt Design C E D B A Housings Customer Service: International Customer Service :

76 Filtration Separation Purification IHP Series Filter Housings High-Purity Industrial Housings The IHP Series of industrial housings are engineered for filtration applications involving chemical systems, highpurity water or critical process streams requiring highpurity output. These rugged vessels are constructed entirely of 316L stainless steel to optimize corrosion resistance. Design characteristics minimize hold-up volumes, provide for easy draining and optimized cleanability. Available as bottom open T style for 3 round 7 round and top open T style for 12 and 21 round. Features Benefits Constructed of 316L stainless steel wetted parts Maximum corrosion resistance and purity Unique bolt-down design Simple, convenient and assures seal integrity Easy draining Tapered bottom permits complete draining Available in three round to 21 round, from 10" to 40" high Accommodates industry standard cartridge configurations Product Specifications Materials: 316L Stainless Steel EPDM O-ring (other options available) Filter connections: DOE, 226, 222 Closure: Opti Clamp Bolt down Surface Finish: External surfaces: Bead-blasted and passivated Internal surfaces: Mill finish and passivated Dimensions Sizes: 3, 5, 6, 7, 12, 21 round Filter Lengths: 10", 20", 30", 40" (25.4, 50.8, 76.2, cm) IHP Housing Dimensional Drawing O-RING SEAL HOLD DOWN PLATE WITH RODS & WING NUTS CARTRIDGE FILTERS VENT "A"REF Operating Parameters Maximum operating pressure: F ( C) "E" OD "B"REF Available Options 150lb ANSI raised face flange Multiple Triclamp/NPT Inlet/Outlet sizes Electropolished CARTRIDGE CONNECTION OUTLET INLET Typical Applications High Purity Chemicals High Purity Water Edible Oils Beverages "C" REF DRAIN "D"REF 70

77 Housings Model 3IHP, 5IHP, 6IHP, 7IHP, 12IHP, 21IHP Series Cartridge Height (10" lengths) 1, 2, 3, 4 Cartridge Connection DOE, 222, 226 IHP Housing Nomenclature Information 5IHP NPT -NPT -2 -E -EP Example: 5IHP NPT-NPT-2-E-EP Vent/Drain NPT, TC Inlet/Outlet NPT, TC, F Inlet/Outlet Size 2 2" 3 3" 4 4" Gasket S Silicone E EPDM V Viton T Teflon encap. Viton Option EP Electropolished IHP Housing Dimensional Data Model Vent/Drain Inlet/Outlet A B C D E 3IHP-1 1 2" Triclamp/NPT 2" Triclamp/NPT 18.25" 28.50" 13.50" 6.0" 6.6" 3IHP-2 1 2" Triclamp/NPT 2" Triclamp/NPT 28.35" 38.50" 13.50" 6.0" 6.6" 3IHP-3 1 2" Triclamp/NPT 2" Triclamp/NPT 38.25" 48.50" 13.50" 6.0" 6.6" 3IHP-4 1 2" Triclamp/NPT 2" Triclamp/NPT 48.25" 58.50" 13.50" 6.0" 6.6" 5IHP-1 1 2" Triclamp/NPT 2" Triclamp/NPT 18.25" 28.50" 13.0" 6.0" 8.62" 5IHP-2 1 2" Triclamp/NPT 2" Triclamp/NPT 28.35" 38.50" 13.0" 6.0" 8.62" 5IHP-3 1 2" Triclamp/NPT 2" Triclamp/NPT 38.25" 48.50" 13.0" 6.0" 8.62" 5IHP-4 1 2" Triclamp/NPT 2" Triclamp/NPT 48.25" 58.50" 13.0" 6.0" 8.62" 7IHP-1 1 2" Triclamp/NPT 2 or 3" Triclamp/NPT 19.50" 31.75" 18.13" 6.50" 10.0" 7IHP-2 1 2" Triclamp/NPT 2 or 3" Triclamp/NPT 29.50" 41.75" 18.13" 6.50" 10.0" 7IHP-3 1 2" Triclamp/NPT 2 or 3" Triclamp/NPT 39.50" 51.75" 18.13" 6.50" 10.0" 7IHP-4 1 2" Triclamp/NPT 2 or 3" Triclamp/NPT 49.50" 61.75" 18.13" 6.50" 10.0" 12IHP-1* 1 2" Triclamp/NPT 3 or 4" Triclamp/NPT 21.50" 33.75" 19.75" 6.50" 12.75" 12IHP-2* 1 2" Triclamp/NPT 3 or 4" Triclamp/NPT 31.50" 43.75" 19.75" 6.50" 12.75" 12IHP-3* 1 2" Triclamp/NPT 3 or 4" Triclamp/NPT 41.50" 53.75" 19.75" 6.50" 12.75" 12IHP-4* 1 2" Triclamp/NPT 3 or 4" Triclamp/NPT 51.50" 63.75" 19.75" 6.50" 12.75" 21IHP-1* 1 2" Triclamp/NPT 3 or 4" Triclamp/NPT 20.50" 35.75" 25.0" 6.50" 18.0" 21IHP-2* 1 2" Triclamp/NPT 3 or 4" Triclamp/NPT 30.50" 45.75" 25.0" 6.50" 18.0" 21IHP-3* 1 2" Triclamp/NPT 3 or 4" Triclamp/NPT 40.50" 55.75" 25.0" 6.50" 18.0" 21IHP-4* 1 2" Triclamp/NPT 3 or 4" Triclamp/NPT 50.50" 65.75" 25.0" 6.50" 18.0" * Top open design Housings Customer Service: International Customer Service :

78 Filtration Separation Purification LPF Series Filter Housings High Quality Multi-Cartridge Filter Housings LPF Series filter housings are constructed of durable stainless steel and meet general purpose industrial and commercial filtration needs. All wetted welded surfaces are stainless steel. External surfaces are bead blasted for a consistent, easy care finish. Features Benefits Durable 304L or 316L stainless steel wetted parts for excellent corrosion resistance Universal seat cups accept DOE or 222 style filters; 226 cups optional Choice of V-band clamp or swing bolts for convenient cartridge change outs Eye nuts on swing bolt style facilitate removal with minimal tools Accepts 10", 20", 30", and 40" cartridges Fully threaded tie rod allows for fitment of various style/lengths of filters; wing nut for ease of removal Removable cartridge posts for easy cleanouts Suitable for flow rates from 21 to 588 GPM Accommodates up to 2 3 /4" OD cartridges Equipped with 1 /4" vent and 1 /2" drain Product Specifications Materials: 304L or 316L Stainless Steel Shell O-ring: Internal Components: Buna N, Viton, EPDM, Teflon encapsulated Viton 316L compression plate and tie rod are included for use with single open end filters.if double open end filters will be used, specify IP (internal parts) in the housing description to obtain tube guides and springs. LPF Housing Dimensional Drawing Swing Bolt Design V-Band Design Operating Parameters Maximum operating 150 psig ( F pressure: in liquid service Not for use with compressed gases Available Options 150lb ANSI raised face flange Various MNPT Inlet/Outlet sizes Legs for maximum stability (standard for LPF 7 and up) Mounting tabs (option for LPF 3 and LPF 5) 226 configuration Gauge ports Hinge or davit arm optional on 21 around Typical Applications Potable water Edible oils Cutting oils Process water Lubricants Solvents Coatings Coolants 72

79 Housings LPF Housing Nomenclature Information LPF 03 R 2 -N 2 -U -VB -E -G PX-T-IP Model LPF Series # of Filters 03 3 around 05 5 around 07 7 around around around Example: 5IHP NPT-NPT-2-E-EP Model Rate Flow Capacity 3 No. 10" Elements gpm (lpm) Material of Construction R 304L SS T 3016L SS Cartridge Height (10" lengths) 1, 2, 3, 4 Inlet/Outlet N NPT F Flange Dim. "A" inches (cm) NOTES: 1 Dimensions are based on th standard connection sizes. 2 Dimensions include support legs. LPF Housing Dimensional Data Dim. "B" inches (cm) Dim. "C" inches (cm) Inlet/Outlet Size 1.5, 2, 3, 4 Seat Cup Style U Universal (DOE or 222) X 226 Closure Type VB V-band SB Swing bolts Dim. "D" 1 inches (cm) Dim. "E" 1 inches (cm) Gasket B Buna-N E EPDM V Viton T Teflon Std. Conn. size/type Option T Tabs H Hinge L Legs GPX Gauge port GPG Gauge port and gauge IP Internal parts (tube guides and springs) DA Davit arm LPF (79) /8" (53) 7" (17.8) 3" (7.6) 9 1/2" (24.1) 10 5/8" (27) 1 1/2" MNPT 1/2" NPT 1/4" NPT LPF (159) /8" (78.4) 7" (17.8) 3" (7.6) 9 1/2" (24.1) 10 5/8" (27) 1 1/2" MNPT 1/2" NPT 1/4" NPT LPF (238) /8" (12.4) 7" (17.8) 3" (7.6) 9 1/2" (24.1) 10 5/8" (27) 1 1/2" MNPT 1/2" NPT 1/4" NPT LPF (318) /8" (129.2) 7" (17.8) 3" (7.6) 9 1/2" (24.1) 10 5/8" (27) 1 1/2" MNPT 1/2" NPT 1/4" NPT LPF (132) /8" (53) 7" (17.8) 3" (7.6) 11 1/4" (28.6) 12 3/4" (32.4) 2" MNPT 1/2" NPT 1/4" NPT LPF (265) /8" (78.4) 7" (17.8) 3" (7.6) 11 1/4" (28.6) 12 3/4" (32.4) 2" MNPT 1/2" NPT 1/4" NPT LPF (398) /8" (12.4) 7" (17.8) 3" (7.6) 11 1/4" (28.6) 12 3/4" (32.4) 2" MNPT 1/2" NPT 1/4" NPT LPF (530) /8" (129.2) 7" (17.8) 3" (7.6) 11 1/4" (28.6) 12 3/4" (32.4) 2" MNPT 1/2" NPT 1/4" NPT LPF (185) /4" (73) 16" 2 (40.6) 9 3/4" 2 (24.8) 13 1/2" (34.3) 14 3/4" (37.5) 2" MNPT 1/2" NPT 1/4" NPT LPF (371) /4" (98.4) 16" 2 (40.6) 9 3/4" 2 (24.8) 13 1/2" (34.3) 14 3/4" (37.5) 2" MNPT 1/2" NPT 1/4" NPT LPF (557) /4" (123.8) 16" 2 (40.6) 9 3/4" 2 (24.8) 13 1/2" (34.3) 14 3/4" (37.5) 2" MNPT 1/2" NPT 1/4" NPT LPF (742) /4" (149.2) 16" 2 (40.6) 9 3/4" 2 (24.8) 13 1/2" (34.3) 14 3/4" (37.5) 2" MNPT 1/2" NPT 1/4" NPT LPF (636) /8" (97.5) 16" 2 (40.6) 9 3/4" 2 (24.8) 17 1/4" (43.8) 17 1/4" (43.8) 3"-150# flange 1/2" NPT 1/4" NPT LPF (954) /8" (125.4) 16" 2 (40.6) 9 3/4" 2 (24.8) 17 1/4" (43.8) 17 1/4" (43.8) 3"-150# flange 1/2" NPT 1/4" NPT LPF (1272) /8" (150.8) 16" 2 (40.6) 9 3/4" 2 (24.8) 17 1/4" (43.8) 17 1/4" (43.8) 3"-150# flange 1/2" NPT 1/4" NPT LPF (1669) /8" (125.4) 16" 2 (40.6) 9 3/4" 2 (24.8) 21 5/8" (54.9) 21 5/8" (54.9) 4"-150# flange 1/2" NPT 1/4" NPT LPF (2226) /8" (150.8) 16" 2 (40.6) 9 3/4" 2 (24.8) 21 5/8" (54.9) 21 5/8" (54.9) 4"-150# flange 1/2" NPT 1/4" NPT Drain 3 Flow capacity based on pleated filters rated at 7GPM per 10" equivalent. Actual flow rate is dependant upon cartridge type and application. Vent Housings Customer Service: International Customer Service :

80 Filtration Separation Purification MC High Quality Multi-Cartridge Filter Housings The MC Series filter housings are constructed of durable stainless steel and meet general purpose industrial and commercial filtration needs. All wetted welded surfaces are stainless steel. External surfaces are sand blasted for a consistent, easy care finish. Features Benefits Durable 304L or 316L stainless steel for corrosion resistance Shouldered seal plates provide a solid fit into the cartridge core to ensure a positive cartridge seal V-band clamp and swing bolts for quick and easy cartridge changeouts Accepts 10, 20, 30 and 40 DOE cartridges Removable cartridge posts for easy cleanouts Suitable for flow rates from 28 to 1456 gpm Accommodates up to 2 3 /4 OD cartridges Series Filter Housings Product Specifications Shell O-ring Standard: Buna N Optional: Viton, EPDM, Silicone Construction: Head & Bottom Seat Plates: 316L stainless steel wetted parts Shell, Vent Plug, Drain Cap: 304L stainless steel wetted parts Internal Components: 316L stainless steel compression seat plate assemblies and tube guides are included with the MC Series Operating Parameters Maximum operating 150 psig ( F pressure: in liquid service Not for use with compressed gases Connections Size Vent Drain Inlet/Outlet 4MC 1 4" (0.6 cm) NPT 1 2" (1.3 cm) NPT 1 1 2" (3.8 cm) NPT 5MC 1 4" (0.6 cm) NPT 1 2" (1.3 cm) NPT 2" (5.1 cm) NPT 7MC 1 4" (0.6 cm) NPT 1 2" (1.3 cm) NPT 2" (5.1 cm) NPT 12MC 1 4" (0.6 cm) NPT 1 2" (1.3 cm) NPT 3" (7.6 cm) Flange 22MC 1 4" (0.6 cm) NPT 1 2" (1.3 cm) NPT 4" (10.2 cm) Flange 36MC 1 4" (0.6 cm) NPT 3 4" (1.9 cm) NPT 6" (15.2 cm) Flange 52MC 1 4" (0.6 cm) NPT 3 4" (1.9 cm) NPT 6" (15.2 cm) Flange MC Housing Dimensional Drawing V-Band Design Swing Bolt Design Available Options 150lb ANSI raised face flange Multiple MNPT or FNPT Inlet/Outlet sizes Legs (standard for 7MC and up) Mounting tabs (option for 4MC, 5MC) 222/226 configuration Gauge ports INLET D OUTLET Overhead Clearance equivalent to length of cartridge VENT 1/4" NPT (PLUGGED) INLET E OUTLET VENT 1/4" NPT (PLUGGED) Typical Applications Potable water Edible oils Cutting oils Process water Lubricants Solvents Coatings Coolants A B C DRAIN 3/4" NPT (PLUGGED) A B C DRAIN 3/4" NPT (PLUGGED) 74

81 Housings MC Housing Nomenclature Information 22MC 3 -SB -304L -F 4 -B Model 4MC 5MC 7MC 12MC 22MC 36MC 1 52MC 1 Cartridge Height (10" lengths) 1 10" 2 20" 3 30" 4 40" Closure Type VB V-band SB Swing bolts Example: 22MC3-SB-304L-F4- B Material of Construction 304L 316L Inlet/Outlet N NPT F Flange Inlet/Outlet Size (inches) Gasket B Buna-N E EPDM V Viton T Teflon Model Rated Flow Capacity 2 gpm (lpm) No. 10" Elements Dim. "A" V-Band inches (cm) MC Housing Dimensional Data Dim. "A" Swing Bolt inches (cm) Dim. "B" inches (cm) Dim. "C" inches (cm) Dim. "D" inches (cm) Dim. "E" inches (cm) Shipping Weight lbs (kg) 4MC-1 28 (106) " (53.0) " (56.5) 7" (17.8) 3" (7.6) " (26.7) " (31.8) 20 (9.1) 4MC-2 56 (212) " (78.4) " (81.9) 7" (17.8) 3" (7.6) " (26.7) " (31.8) 30 (13.6) 4MC-3 84 (318) " (103.8) " (107.3) 7" (17.8) 3" (7.6) " (26.7) " (31.8) 40 (18.1) 4MC (424) " (129.2) " (132.7) 7" (17.8) 3" (7.6) " (26.7) " (31.8) 50 (22.7) 5MC-1 35 (132) " (53.0) " (56.5) 7" (17.8) 3" (7.6) " (26.7) " (31.8) 26 (11.8) 5MC-2 70 (265) " (78.4) " (81.9) 7" (17.8) 3" (7.6) " (26.7) " (31.8) 32 (14.5) 5MC (398) " (103.8) " (107.3) 7" (17.8) 3" (7.6) " (26.7) " (31.8) 43 (19.5) 5MC (530) " (129.2) " (132.7) 7" (17.8) 3" (7.6) " (26.7) " (31.8) 48 (21.8) 7MC-1 49 (185) " (52.1) 21 (53.3) " (20.5) " (8.4) " (31.8) " (36.8) 44 (20.0) 7MC-2 98 (371) " (77.5) 31 (78.7) " (20.5) " (8.4) " (31.8) " (36.8) 53 (24.0) 7MC (557) " (102.9) 41 (104.1) " (20.5) " (8.4) " (31.8) " (36.8) 70 (31.8) 7MC (742) " (128.3) 51 (129.5) " (20.5) " (8.4) " (31.8) " (36.8) 91 (41.3) 12MC (636) " (100.3) " (102.9) " (38.4) 9 3 4" (24.8) " (31.8) " (36.8) 86 (39.0) 12MC (954) " (125.7) " (128.3) " (38.4) 9 3 4" (24.8) " (31.8) " (36.8) 92 (41.7) 12MC (1272) " (151.1) " (153.7) " (38.4) 9 3 4" (24.8) " (31.8) " (36.8) 100 (45.4) 22MC-3 3,4 462 (1749) " (127.5) " (127.5) " (38.7) 9 1 2" (24.1) " (52.1) " (57.2) 140 (63.5) 22MC-4 3,4 616 (2332) " (152.9) " (152.9) " (38.7) 9 1 2" (24.1) " (52.1) " (57.2) 165 (74.8) 36MC-3 3,4 756 (2861) 108 n/a " (177.2) " (82.2) 14 (35.6) n/a " (65.7) 340 (154.2) 36MC-4 3, (3816) 144 n/a " (189.9) " (82.2) 14 (35.6) n/a " (65.7) 360 (163.3) 52MC-3 3, (4134) 156 n/a " (167.5) " (82.2) 14 (35.6) n/a " (75.9) 520 (235.9) 52MC-4 3, (5512) 208 n/a " (192.9) " (82.2) 14 (35.6) n/a " (75.9) 550 (249.5) NOTES: 1 36MC and 52MC Series Housings only available with SB closures. 2 Flow capacity based on pleated filters rated at 7GPM per 10" equivalent. Actual flow rate is dependant upon cartridge type and application. 3 Dimensions include support legs. 4 Housing accepts a maximum of 2 5 8" cartridges. Housings Customer Service: International Customer Service :

82 Filtration Separation Purification SC Series Filter Housings Single Cartridge Filter Housings The SC Series of single cartridge metal filter housings are available in 304L or 316L stainless steel wetted parts with either bolt or ring seal closure to service a wide range of general purpose filter applications. The SCR Ring Closure Series provide superior design features to serve higher pressure applications, allow full sump drainage and utilize a wider range of cartridge configurations. The SCB Bolt Closure Series is an economical design for double open ended cartridges. Features Benefits Single shell construction for quick spill-free cartridge replacement In-line pipe connections for easy installation in 1 /2, 3 /4 and 1 inch pipe sizes Drains built in Rated for flow rates to 7 GPM (26.5 lpm) per 10 inch filter cartridge length Mounting brackets are available Housing pressure drop is 0.6 psid at 7 gpm ( lpm) SCR (with Ring Seal Closure) Superior design accommodates most cartridges, higher pressure and complete housing drainage High pressure seal design supports pressures to 300 psi ( F (93 C) Center rod is eliminated to permit the use of double open end or single open end cartridges Tapered housing bottom permits complete drainage Model available for 222 and 226 O-ring style cartridge in all 316L stainless steel wetted parts SCB (with Bolt Closure) Economical design accommodates DOE cartridges Optional T-handle available for sump removal Temperature rated to 250 F (121 C) and 250 psi (17.23 bar) maximum pressure SCR Ring Closure Housing Typical Applications Process water Potable liquids Petro chemicals Coolants Hydraulic oils Solvents SCB Bolt Closure Housing 76

83 Housings Model SCB, SCR SC Housing Nomenclature Information SCR 10 BSS 075 DOE -E Cartridge Height (10" lengths) " 10 10" 30 30" " 20 20" Material of Construction BSS 304L 1 316L Inlet/Outlet Size " " " Connector DOE, 222 2, Gasket B Buna-N S Silicone E EPR V Viton T Teflon Legend SCB Single Cartridge (with Bolt Closure) SCR Single Cartridge (with Ring Closure) 304L 304L Sump, 316L Head 316L 316L Sump & Head BSS Brass Head, 304L Sump Example: SCR 10BSS075DOE-E 1 Not available in SCR. 2 Available as 316L only. SC Housing Specifications Model Cartridge Length Rated Capacity Shipping Weight Cartridge Endcap Maximum Pressure Maximum Temp. inches (cm) GPM (LPM) lbs (kg) Type PSIG (bar) F ( C) SCB " (12.4) 3.5 (13.3) 4 (1.8) DOE 250 (17.2) 250 (121.1) SCB " (24.8) 7 (26.5) 7 (3.2) DOE 250 (17.2) 250 (121.1) SCB-10 10" (25.4) 7 (26.5) 7 (3.2) DOE 250 (17.2) 250 (121.1) SCB-20 20" (50.8) 14 (53.0) 10 (4.5) DOE 250 (17.2) 250 (121.1) SCB-30 30" (76.2) 21 (79.5) 12 (5.4) DOE 250 (17.2) 250 (121.1) SCR " (24.8) 7 (26.5) 7 (3.2) SOE or DOE 300 (20.7) 200 (93.3) SCR-10 10" (25.4) 7 (26.5) 7 (3.2) SOE or DOE 300 (20.7) 200 (93.3) SCR-20 20" (50.8) 14 (53.0) 10 (4.5) SOE or DOE 300 (20.7) 200 (93.3) SCR-30 30" (76.2) 21 (79.5) 12 (5.4) SOE or DOE 300 (20.7) 200 (93.3) SC Housing Dimensional Data Model A inches (cm) B inches (cm) C inches (cm) D inches (cm) SCB-04 4" (10.2) n/a 8 7 8" (22.6) 6" (15.2) SCB-09 4" (10.2) n/a " (34.9) 11" (27.9) SCB-10 4" (10.2) n/a " (34.9) 11" (27.9) SCB-20 4" (10.2) n/a " (60.6) 21" (53.3) SCB-30 4" (10.2) n/a " (86.0) 31" (78.7) SCR " (11.4) " (8.4) " (33.3) " (28.9) SCR " (11.4) " (8.7) " (33.7) " (29.2) SCR " (11.4) " (8.7) " (59.1) " (54.6) SCR " (11.4) " (8.7) " (84.5) " (80.0) SCR / " (11.4) " (8.7) 18" (45.7) " (41.8) SCR / " (11.4) " (8.7) 28" (71.1) " (66.7) SCR / " (11.4) " (8.7) 18" (96.5) " (92.1) SCB SC Housing Dimensional Drawing VENTS (OPTIONAL) INLET C D SCR HEAD HEAD A A CAP NUT B GASKET INLET OUTLET OUTLET RING GASKET SPRING CARTRIDGE CENTERING DEVICE CARTRIDGE CENTER ROD SUPPORT C D SHELL SHELL CARTRIDGE CARTRIDGE CARTRIDGE SEAL PLATE PETCOCK DRAIN BOTTOM SEAL PLATE 1 /8'' DRAIN Housings Customer Service: International Customer Service :

84 Filtration Separation Purification SHP Series Filter Housings High-Purity Sanitary Housings The SHP Series of sanitary housings are engineered using 3A sanitary standards for filtration applications involving ultrapure chemical systems, ultrapure water or critical process streams requiring sanitary production stream. These rugged vessels are constructed entirely of 316L stainless steel to optimize corrosion resistance. Design characteristics minimize hold-up volumes, provide for easy draining and optimized cleanability. Available as T style or inline (one round only). Features Benefits Constructed of 316L stainless steel wetted parts Maximum corrosion resistance and purity Meets 3A Sanitary Design Standards Unique bolt-down design on multi-round Simple, convenient and assures seal integrity Easy draining Tapered bottom permits complete draining Available in one round to 7 round, from 10" to 40" high Accommodates industry standard 222 and 226 cartridge configurations Product Specifications Materials: 316L Stainless Steel wetted parts EPDM O-ring (other options available) Filter connections: 226, 222 Closure: 304 SS Clamp (1 round only) Opti Clamp Bolt down Surface Finish: External surfaces: 20 RA, Electropolished Internal surfaces: 20 RA, Electropolished SHP Housing Dimensional Drawing 1-1/2'' TRICLAMP NOZZLE w-1/2'' TRICLAMP SIDE OUTLET Dimensions Sizes: 1, 3, 5, 7 Round Filter Lengths: 10", 20", 30", 40" (25.4, 50.8, 76.2, cm) Operating Parameters Maximum operating pressure: F ( C) CARTRIDGE FILTERS "E" OD 222 CODE 8 OR 226 CODE 7 MACHINED SEPARATOR PL "A" REF O-RING SEALS "B" REF Typical Applications Ultrapure Chemicals Wine/Beer Diagnostics Ultrapure Water Vaccines OUTLET INLET (2) DRAINS "D" REF "C" REF 78

85 Housings SHP Housing Nomenclature Information 5SHP T C -TC -2 -E -EP Model 1SHP, 1SHP-L Inline, 3SHP, 5SHP, 7SHP Series Cartridge Height (10" lengths) 1, 2, 3, 4 Cartridge Connection 222, 226 Example: 5ISHP TC-TC-2-E-EP Vent/Drain TC Triclamp Inlet/Outlet TC Triclamp Inlet/Outlet Size 1 1" " 2 2" Gasket S Silicone E EPDM V Viton T Teflon encap. Viton EP Electropolished SHP Housing Dimensional Data Model Vent/Drain Inlet/Outlet A B C D E 1SHP-1* 1 2" Triclamp/1.4" 1.0" Triclamp 13.75" 22.0" 9.75" 6.0" 4.0" 1SHP-2* 1 2" Triclamp/1.4" 1.0" Triclamp 23.75" 32.0" 9.75" 6.0" 4.0" 1SHP-3* 1 2" Triclamp/1.4" 1.0" Triclamp 33.75" 42.0" 9.75" 6.0" 4.0" 1SHP-L1* 1 2" Triclamp/1.4" 1.5" Triclamp 13.75" 19.5" NA NA 4.0" 1SHP-L2* 1 2" Triclamp/1.4" 1.5" Triclamp 23.75" 29.5" NA NA 4.0" 1SHP-L3* 1 2" Triclamp/1.4" 1.5" Triclamp 33.75" 39.5" NA NA 4.0" 3SHP-1 1 2" Triclamp/1.4" 2" Triclamp 15.90" 28.50" 13.55" 6.0" 6.6" 3SHP-2 1 2" Triclamp/1.4" 2" Triclamp 25.90" 38.50" 13.55" 6.0" 6.6" 3SHP-3 1 2" Triclamp/1.4" 2" Triclamp 35.90" 48.50" 13.55" 6.0" 6.6" 3SHP-4 1 2" Triclamp/1.4" 2" Triclamp 45.90" 58.50" 13.55" 6.0" 6.6" 5SHP-1 1 2" Triclamp/1.4" 2" Triclamp 15.65" 28.25" 14.38" 6.0" 10.75" 5SHP-2 1 2" Triclamp/1.4" 2" Triclamp 25.65" 38.25" 14.38" 6.0" 10.75" 5SHP-3 1 2" Triclamp/1.4" 2" Triclamp 35.65" 48.25" 14.38" 6.0" 10.75" 5SHP-4 1 2" Triclamp/1.4" 2" Triclamp 45.65" 58.25" 14.38" 6.0" 10.75" 7SHP-1 1 2" Triclamp/1.4" 2" Triclamp 15.65" 28.25" 14.38" 6.0" 10.75" 7SHP-2 1 2" Triclamp/1.4" 2" Triclamp 25.65" 38.25" 14.38" 6.0" 10.75" 7SHP-3 1 2" Triclamp/1.4" 2" Triclamp 35.65" 48.25" 14.38" 6.0" 10.75" 7SHP-4 1 2" Triclamp/1.4" 2" Triclamp 45.65" 58.25" 14.38" 6.0" 10.75" * Top open design Housings Customer Service: International Customer Service :

86 Filtration Separation Purification Terms & Conditions of Sale ACCEPTANCE BY GRAVER TECHNOLOGIES LLC ( Seller ) OF ANY OFFER OR PURPORTED OFFER IS EXPRESSLY MADE CONDITIONAL TO THE ASSENT OF THESE TERMS AND CONDITIONS OF SALE (these Terms ). SELLER REJECTS ANY PRIOR OFFERS MADE BY BUYER WITH REGARD TO THE PRODUCTS. 1. Quotations. Unless otherwise specified in writing, quotations are valid for 30 days. Prices quoted do not include any sales, use, excise, occupational or other tax or freight unless otherwise specified. Pricing is based upon the quantity and type specified and subject to revision when interruptions, engineering changes, or changes in quantity are caused or requested by the Buyer. 2. Scope. Seller intends to provide the goods and services requested by Buyer. 3. Acceptance. All orders are subject to approval and written acceptance by an authorized representative of Seller. No product may be returned without Seller s prior written approval. Any change requires written consent and may result in a change in price, delivery, payment, or performance warranties. A restocking charge, at Seller s discretion, may be applied against material returned for credit. 4. Delivery/Force Majeure. Delivery lead times are approximate and based on receipt of timely and accurate information from Buyer. Seller reserves the right to make partial shipment and invoice therefor. Seller assumes no liabilities for delays or non-performance resulting from, but not limited to, Acts of God, fire, explosion, flood, war, terrorism or threats of terrorism, act of or as authorized by any government, accident, labor trouble or shortage, inability to obtain equipment, material, transportation, acts of Buyer or any acts beyond the control of Seller. Delivery to carrier shall constitute delivery to Buyer and all risk of loss or damage in transit shall be borne by Buyer. If, because of Buyer s inability to take delivery, the products are not shipped or returned, Seller may have them stored for Buyer at Buyer s expense, risk, and account, and for all other purposes they shall be considered shipped. Buyer shall unload, handle, store and install the products in accordance with generally accepted practice or specific instructions provided for the equipment, membranes and/or media. 5. Packaging. All items sold hereunder shall be packed or crated and shipped in accordance with Seller s specifications. Any special packing, crating, shipping or unloading requirements of Buyer must be agreed upon by Seller in advance at additional cost. Weights listed, if any, are approximate. 6. Inspection. Buyer shall inspect goods upon arrival and shall give written notice of any damage or shortage to Seller and carrier within 10 days. Failure to give such written notice of any damage or shortage will constitute satisfactory shipment by Seller and irrevocable acceptance by Buyer of all items listed as contained. Claims for shipping damage should be made directly to the carrier by the Buyer. 7. Repairs and Alterations. Any repairs or alterations made to goods shall void all warranties and be at the expense of Buyer unless specifically authorized in writing by Seller. In no event shall Seller accept back charges for unauthorized repairs or alterations. 8. Limited Warranty. Unless explicitly stated in writing signed by Seller, Seller warrants its products against defects in workmanship and material at the time of shipment from the factory. Specifications provided by Seller are guidelines only and the particular use and application will determine the actual life of the product, media or membrane. Seller s liability under this warranty shall be limited to the replacement or repair, at Seller s sole discretion, F.O.B. factory, of any defective product which having been returned to the factory, transportation charges prepaid, has been inspected and determined by Seller to be defective. The warranty on component parts not manufactured by Seller is limited to that of the manufacturer thereof, if any. The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation, or other expenses which may be incurred in connection with replacement or repair. THE FOREGOING WARRANTIES ARE BUYER S EXCLUSIVE REMEDY AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, COURSE OF DEALING AND USAGE OF TRADE. 9. Limitation Of Liability. Under no circumstances shall Seller be liable to Buyer or any other person or entity for incidental, consequential, direct, exemplary, punitive or special damages or any other losses or expenses, including without limitation, for injuries to persons or damage to property, loss of profit or revenues, cost of substitute products, loss of use, downtime costs, or claims of Buyer s customers even if Seller has been advised of the possibility of such damages. Seller s aggregate liability arising out of or relating to any products purchased shall not exceed the purchase price actually received by Seller for the allegedly defective products. 10. Disposal. Buyer shall be responsible and fully liable for the disposal of any product, including, without limitation, spent product or material, and shall perform such disposal in compliance with all federal, state and local laws and regulations relating thereto. 11. Service. Upon reasonable request, Seller may make available to Buyer the services of a trained representative at Seller s then current prevailing rates, plus travel, living and out of pocket expenses. In no event shall charges for technical direction of field installation and/or start-up be considered as included in the quoted price unless otherwise expressly stated in writing by Seller. 80

87 Terms & Conditions 12. Indemnity. Buyer shall defend, indemnify and hold Seller, its agents and employees harmless from and against all suits (including reasonable attorneys fees), including death or injury, arising out of or relating to Buyer s (i) provided specifications, structure, operation, material, or method of making products, including, without limitation, any resulting violation of intellectual or proprietary rights, (ii) use, misuse or disposal of products or materials, and (iii) breach of these Terms and Conditions by Buyer. 13. Payment Terms. All payments are due at location stated on invoice. Custom products require progress payments as designated by Seller. All other products are net cash within 30 days of shipment unless otherwise expressly stated in writing by Seller. Seller reserves the right to modify its payment terms at any time. Invoices not paid when due are subject to a late payment service charge of the lesser of 1-1/2% (one and one half percent) per month or the maximum legal service charge permitted under the law. If Buyer fails to make any payment when due, Buyer shall be liable for all expenses related to collection of past due amounts, including, without limitation, attorneys fees and costs. 14. Cancellation. Custom orders may not be cancelled or returned. Cancellation of standard in-stock products are subject to a 25% restocking fee. 15. Compliance. The products furnished herein may not comply with all Federal, State, and local laws, regulations or ordinances unless expressly agreed to in writing. All shipments hereunder are subject to the export control laws and regulations of the United States and any amendments thereto. Buyer agrees that it shall not make any disposition of U.S. origin Products purchased from Seller, by way of transshipment, re-export, diversion or otherwise, other than in and to the country of ultimate destination on Seller s invoices except as said laws and regulations may expressly permit. 16. Typographical Errors. Seller is not responsible for typographical errors made in any of its publications or for clerical errors made in preparation of quotations, sales orders or acknowledgments. All such errors are subject to correction. 17. Applicable Law. The laws of the State of Delaware shall govern these Terms and Conditions and the courts of Delaware shall be the exclusive venue and jurisdiction. 18. Arbitration. In case of any controversy, claims, or disputes arising out of or relating to these Terms and Conditions or the breach hereof, the parties shall meet to attempt to negotiate an amicable settlement. In the event the parties fail to reach an amicable settlement, Buyer hereby agrees that Seller may, at Seller s sole option, require Buyer to arbitrate any controversy, claim or dispute arising out of or relating to these Terms and Conditions or any other issue. If Seller chooses arbitration, such arbitration shall be conducted in the English language, and shall take place in Wilmington, Delaware. The arbitration tribunal shall be composed of three arbitrators appointed pursuant to the procedures set forth in the rules of the American Arbitration Association. Judgment may be entered on the award by any court having jurisdiction. Neither party shall have the right of discovery during the arbitration process. 19. Governance. Buyer and Seller each agree that these terms and conditions shall govern and control with respect to all orders by Buyer from Seller, and no term, condition, warranty or representation appearing in any purchase order of Buyer or order acknowledgment, invoice or other sales documentation of Buyer, will govern unless agreed to in writing by Seller. 20. Nondisclosure. Neither party hereto shall disclose any information regarding any the subject matter hereof or proprietary technical information received from the other party, except to the extent that disclosure is required by law or is otherwise agreed to in writing by the parties. 21. Severability. In the event that any provision herein shall be found to be void or unenforceable, this shall not be construed to render any other provisions void or unenforceable, and all other provisions shall remain in full force and effect unless the provisions which are invalid or unenforceable shall substantially affect the rights or obligations granted to or undertaken by the Parties. 22. Notices. All notices to Seller shall be given in writing and will be deemed effective on the third day after mailing if sent by certified mail, postage prepaid, return receipt requested, or on the day after deposit if sent by overnight delivery service which maintains records of the time, place and receipt of delivery. 23. Changes. Any changes or revisions to these terms and conditions must be authorized in writing by Seller s President or Vice-President of Finance. 24. Entirety. These terms and conditions together with the exhibits referenced and attached hereto embodies the entire understanding between Buyer and Seller and there are no agreements, understandings, conditions, warranties, or representations, oral or written, express or implied, with reference to the subject matter hereof which are not merged herein. Rev. 08/2013 Customer Service: International Customer Service :

88 Filtration Separation Purification Notes

89 PHARMACEUTICAL MARKETS PROCESS WATER Graver Technologies Liquid Process Filter Group provides products and services that meet stringent stringent application application requirements requirements in a variety in of a variety markets, of markets, including including Process Water, Process Food Water, & Beverage, Food & Beverage, Pharmaceutical, Pharmaceutical, Microelectronics Microelectronics and Chemicals. and Chemicals. FOOD & BEVERAGE MICROELEC TRONICS CHEMICAL

90 Filtration Separation Purification Superior Products & Global Reach Whether your business is around the corner or around the world, Graver Technologies can support you with superior products and services. Our ion exchange, adsorbent, filtration, and membrane products deliver exceptional performance in some of the harshest process environments in North America, Europe, Asia, the Pacific Rim, South America, and Africa. Graver Technologies is a member of The Marmon Group (a Berkshire Hathaway Company), an international group with more than $7 billion in annual sales. Around the corner or around the world, Graver Technologies is a fast growing company with the technical resources and financial strength that make us the perfect partner for your business. Corporate Headquarters 200 Lake Drive Glasgow, Delaware U.S.A. Telephone: Fax: info@gravertech.com Website: Customer Service Toll-free (in U.S.): Outside US: Technical Support: info@gravertech.com Graver Technologies Europe (UK): Graver Technologies China: Graver Technologies LLC. Made with Pride in the USA