Product Catalogue. Sand Management Well Testing Equipment Technical Information

Transcription

1 Well Testing Product Catalogue Sand Management Well Testing Equipment Technical Information

2 Excellence in Energy Services for over 100 years web Well Testing Global Locations The Netherlands United Kingdom Middle East Asia Pacific Olieweg NH Velsen-Noord The Netherlands Badentoy Avenue Badentoy Industrial Park Portlethen, Aberdeen AB12 4YB, UK Building 23 Oilfields Supply Center Jebel Ali, P.O. Box Dubai, UAE 2 International Business Park #04-13/14 The Strategy Tower 1 Singapore T. +31 (0) F. +31 (0) T. +44 (0) F. +44 (0) T F T F

3 Well Testing Contents Well Testing Product Catalogue Contents About Hunting Introduction to Well Testing Well Testing Product Range 09 Sand Management Dual Pot Sand Filter (Type A) Dual Pot Sand Filter (Type AH) Dual Pot Sand Filter (Type B) Dual Pot Sand Filter (Type B HPHT) Cyclonic Wellhead Desander Interchangeable Wellhead Desander Well Testing Equipment Choke Manifold Wellhead Plug Catcher Heat Exchanger (Standard Type) Heat Exchanger (Container Type) Vertical Surge Tank Piping, Cross-overs And Instrumentation Packages Technical Information Dual Pot Sand Filter (Type A) Dual Pot Sand Filter (Type AH) Dual Pot Sand Filter (Type B) Dual Pot Sand Filter (Type B HPHT) Cyclonic Wellhead Desander Interchangeable Wellhead Desander Choke Manifold Wellhead Plug Catcher Heat Exchanger (Standard Type) Heat Exchanger (Container Type) Vertical Surge Tank

4 API CERTIFIED 04 OVER 100 FACILITIES EMPLOYEES WORLDWIDE 24 HOUR SUPPORT

5 Well Testing About Hunting Hunting provides products and services to the world s leading national, international energy companies and oil service companies enabling the extraction of oil and gas. Manufacturing and sales locations are located in the key energy producing regions of the world. Global Business Divsions Connection Technology Electronics Specialty Supply Trenchless Products Dearborn Manufacturing Subsea Technology Well Intervention Equipment Drilling Tools OCTG Titan 05 Proprietary Technology Hunting owns and develops proprietary patented products with a full range of applications below the wellhead including mud motors, premium connections, well perforating, logging and intervention tools. Geographic Footprint In strategic locations around the world Hunting owns and operates plants, properties and equipment, employing people to serve its global customers with local services and products. Hunting is committed to working safely in an environmentally responsible manner. These principles are fully integrated within our QMS that defines the company s global operations. Quality Assurance It is essential that products and services provided by Hunting are designed and manufactured to conform to the agreed API, proprietary licensor, or other specification of the customer, meeting their needs and expectations the first time, every time. It is the policy of Hunting that only the highest quality products and services, that meet all specification requirements, are provided to customers. Hunting operates a corporate Quality Management System covering all worldwide locations. Health, Safety and Environment Hunting is committed to achieving and maintaining the highest standards of safety for its employees, customers, suppliers and the public. All Hunting business units consciously operate in a manner that includes environmental matters as an integral part of its business plan. Hunting s aims are no accidents, no harm to people, and no damage to the environment. The Hunting goal is Total Customer Satisfaction.

6 Well Testing Introduction to Well Testing Hunting offers a unique combination of high quality manufactured well testing equipment and fabrication services. Together with more than 30 years experience and using highly qualified welding processes, Hunting manufactures superior and customised well testing equipment. Product Development 06 Hunting's engineering team have extensive experience in developing well test technology to meet the current industry challenges of managing solids production in high pressure and high flow-rate applications. In addition to offering a wide range of industry standard products, the team is also ready to work closely with their client's on customized equipment to optimize a solution both in terms of cost and operational efficiency. Engineering and Manufacturing Capabilities All the detailed engineering studies including 2D/3D modeling and both FEM and CFD calculations in close co-operation with the manufacturing team. The Hunting well test facility is able to engineer, fabricate, assemble and test their oilfield products under one roof meeting all the latest industry requirements for quality systems and manufacturing codes. These include: ISO 9001 ISO OHSAS PED 97/23/EC ASME B31.3 ASME VIII DIV.1, 2 & 3 API 6A NACE MR-01-75/ISO ATEX DNV & DNV Lifting Appliance DNV OS-E-101 NORSOK

7 07 Hunting s extensive product portfolio includes sand filters, heat exchangers, choke manifolds, plug catchers and piping equipment. Hunting s dedicated and experienced well testing division is committed to improving well productivity in the most challenging environments. Our success has been built around knowledge of the industry, correct planning, reliability of the equipment and ability to react to client requirements through timely engineering service and teamwork.

8

9 SAND MANAGEMENT Hunting s Well Testing division has developed a comprehensive sand management solution with a range of safe and efficient high-pressure sand removal technologies to address the industry challenge of avoiding damage by erosion and plugging of process equipment during well testing, frac flowback and clean-up operations. 09 Dual Pot Sand Filter (Type A) Dual Pot Sand Filter (Type AH) Dual Pot Sand Filter (Type B) Dual Pot Sand Filter (Type B HPHT) Cyclonic Wellhead Desander Interchangeable Wellhead Desander

10 Well Testing Sand Management 10 Dual Pot Sand Filter (Type A) Product Code DSF-A FEATURES Separates sand and other solid particles from the well stream Dual pot system with high pressure by-pass and dual isolation valves Switching flow between pots for continuous sand removal Telescopic lifting support for convenient filter replacement Quick union on pot vessels for rapid filter replacement & maintenance Optional water jet sand flushing system Optional Sandbox for sand disposal BENEFITS Simple to operate Eliminates erosion on choke manifold and downstream process equipment Enables high rate well testing Allows representative sand sampling and sand production rate estimation Wellhead sand filtration is established as an industry standard technique for sand and solids removal upstream of the choke manifold during well testing, frac-flowback and well clean-up operations. The Hunting Dual Pot Sand Filters are available in a broad range of sizes and configurations, up to 20,000psi WP. These products are in service globally with major production testing companies. The principle of sand filtering is well understood, with the minimum size of the separated sand particles determined by the slot size in the sand filter in each pot which are available in a range from 100 to 800 microns. Continuous operation is achieved by switching the flow between the two pots and draining the collected sand from the bottom of the pot that is isolated from the flow. Dual Pot Sand Filter (Type A) The Type A Sand Filter is configured for the well to flow from the inside of the filter and the sand to collect therein. The sand can be removed with the filter or purged with water jets. Optional equipment includes a sand flushing system using pressurized water injection through nozzles mounted on the pot vessel outside diameter and a sandbox for collection of the solids slurry exiting the 2 diameter drain valve. For technical information see page 36

11 Telescopic Lifting Support Assists sand filter replacement. Upper Operations Deck Allows easy access to remove quick union pot vessels during filter replacement. 11 Dual Pot System Allows continuous operation.

12 Well Testing Sand Management 12 Dual Pot Sand Filter (Type AH) Product Code DSF-AH FEATURES Separates sand and other solid particles from the well stream Dual pot system with high pressure by-pass and dual isolation valves Switching flow between pots for continuous sand removal Horizontal operation and transportation without need to lift to vertical Telescopic lifting support for convenient filter replacement Quick union on pot vessels for rapid filter replacement & maintenance Optional water jet sand flushing system Optional Sandbox for sand disposal BENEFITS Simple to operate Eliminates erosion on choke manifold and downstream process equipment Enables high rate well testing Can be operated in areas with height restrictions Allows representative sand sampling and sand production rate estimation Wellhead sand filtration is established as an industry standard technique for sand and solids removal upstream of the choke manifold during well testing, frac-flowback and well clean-up operations. The Hunting Dual Pot Sand Filters are available in a broad range of sizes and configurations, up to 20,000psi WP. These products are in service globally with major production testing companies. The principle of sand filtering is well understood, with the minimum size of the separated sand particles determined by the slot size in the sand filter in each pot which are available in a range from 100 to 800 microns. Continuous operation is achieved by switching the flow between the two pots and draining the collected sand from the bottom of the pot that is isolated from the flow. The Type AH Sand Filter is configured for the well to flow from the inside of the filter and the sand to collect therein. The sand can be removed with the filter or purged with water jets. Dual Pot Sand Filter (Type AH) The Type A-H is custom configured for use in an area where there are height restrictions and is both operated and transported in the horizontal position. It does not need to be swivelled upright for operation and can be used in areas where there are height restrictions. Optional equipment includes a sand flushing system using pressurized water injection through nozzles mounted on the pot vessel outside diameter and a sandbox for collection of the solids slurry exiting the 2 diameter drain valve. For technical information see page 37

13 Telescopic Lifting Supports Assist sand filter replacement. Lowered Upper Operations Deck Horizontally configured valve manifolds and lowered sand filter vessels allow the upper operations deck to be lowered to work in areas with height restrictions. 13

14 Well Testing Sand Management 14 Dual Pot Sand Filter (Type B) Product Code DSF-B FEATURES Separates sand and other solid particles from the well stream Dual pot system with high pressure by-pass and dual isolation valves Switching flow between pots for continuous sand removal Telescopic lifting support for convenient filter replacement Quick union on pot vessels for rapid filter replacement & maintenance Optional water jet sand flushing system BENEFITS Simple to operate Eliminates erosion on choke manifold and downstream process equipment Enables high rate well testing Allows representative sand sampling and sand production rate estimation Wellhead sand filtration is established as an industry standard technique for sand and solids removal upstream of the choke manifold during well testing, frac-flowback and well clean-up operations. The Hunting Dual Pot Sand Filters are available in a broad range of sizes and configurations, up to 20,000psi WP. These products are in service globally with major production testing companies. The principle of sand filtering is well understood, with the minimum size of the separated sand particles determined by the slot size in the sand filter in each pot which are available in a range from 100 to 800 microns. Continuous operation is achieved by switching the flow between the two pots and draining the collected sand from the bottom of the pot that is isolated from the flow. Dual Pot Sand Filter (Type B) The Type B Sand Filter is configured for the well to flow through the sand filter from the outside with the sand collecting in the annulus between the vessel and filter. The Sand Filter can be flushed be using a 2 line connection mounted on the inlet piping of vessel. The water flushes the outside diameter of the screen into a 2 drain line for collection of the solids. For technical information see page 38

15 Telescopic Lifting Supports Assist sand filter replacement. Upper Operation Deck Allows easy access to remove quick union on pot vessels during filter replacement. 15 Dual Pot System Allows continuous operation.

16 Well Testing Sand Management 16 Dual Pot Sand Filter (Type B-HPHT) 4-1/16 15K Product Code DSF-B-HPHT FEATURES Separates sand and other solid particles from the well stream Dual pot system with high pressure by-pass and dual isolation valves Switching flow between pots for continuous sand removal Telescopic lifting support for convenient filter replacement Hub connection on pot vessels for filter replacement & maintenance Water connection for sand flushing Optional Sandbox for sand disposal BENEFITS Simple to operate Eliminates erosion on choke manifold and downstream process equipment Enables high rate well testing Allows representative sand sampling and sand production rate estimation Wellhead sand filtration is established as an industry standard technique for sand and solids removal upstream of the choke manifold during well testing, frac-flowback and well clean-up operations. The Hunting Dual Pot Sand Filters are available in a broad range of sizes and configurations, up to 20,000psi WP. These products are in service globally with major production testing companies. The principle of sand filtering is well understood, with the minimum size of the separated sand particles determined by the slot size in the sand filter in each pot which are available in a range from 100 to 800 microns. Continuous operation is achieved by switching the flow between the two pots and draining the collected sand from the bottom of the pot that is isolated from the flow. The Type B-HPHT Sand Filter is configured for the well to flow through the sand filter from the outside with the sand collecting in the annulus between the vessel and filter. The Sand Filter can be flushed be using a 2 line connection mounted on the inlet piping of vessel. The water flushes the outside diameter of the screen into a 3 drain line for collection of the solids. For technical information see page 39 Dual Pot Sand Filter (Type B-HPHT)

17 Filter Screen Flows from inside to outside. 20ft Container Skid Comes with cornerpockets for transportation. 17 Base Frame Makes connection between the two skids.

18 Well Testing Sand Management 18 Cyclonic Wellhead Desander Product Code CWD FEATURES Cyclone separator insert can be easily changed out Dual pot system with high pressure by-pass and dual isolation valves Lifting support for sand filter and cyclone separator interchange High efficiency of solids separation (up to 99%) at high flow rates Handles high flow rates with minimal back pressure Continuous sand disposal by gravity and water flushing Separates a wide range of particle sizes from the well stream BENEFITS Eliminates erosion on choke manifold and downstream process equipment Enables high rate well testing Allows representative sand sampling and sand production rate estimation The Hunting Cyclonic Wellhead Desander offers a robust high pressure solids management solution upstream of the choke manifold during well testing, frac-flowback and well clean-up operations. Cyclonic de-sanders have a high efficiency of separation at high flow-rates with minimal pressure drop and can handle both a wider range of particle sizes and larger volumes of solids when compared to sand filters. The cyclonic separator element is engineered from a highly wear-resistant alloy, is designed to be the only component potentially exposed to erosion and is simple to replace during operations if required. Cyclonic Wellhead Desander The Hunting Cyclonic Wellhead Desander features a dual pot system which allows continuous sand separation and dumping by switching flow from one vessel to the other. The Hunting cyclonic technology has been independently flow loop tested to verify solids separation performance. For technical information see page 40

19 Cyclonic Access Point Cyclonic separator element can be replaced during operations if required. Upper Operations Deck 19 Dual Pot Systems Allows continuous operation.

20 Well Testing Sand Management 20 Interchangeable Wellhead Desander Product Code IWD FEATURES Cyclone separator insert is interchangeable with a sand filter Dual pot system with high pressure by-pass and dual isolation valves Lifting support for sand filter and cyclone separator interchange High efficiency of solids separation (up to 99%) at high flow rates Handles high flow rates with minimal back pressure Continuous sand disposal by gravity and water flushing Separates a wide range of particle sizes from the well stream BENEFITS Flexible solids separation configuration on a single wellhead package Eliminates erosion on choke manifold and downstream process equipment Enables high rate well testing Allows representative sand sampling and sand production rate estimation The Hunting Interchangeable Wellhead Desander offers a flexible high pressure sand management solution upstream of the choke manifold during well testing, frac-flowback and well clean-up operations. Cyclonic de-sanders have a high efficiency of separation at high flow-rates with minimal pressure drop and can handle both a wider range of particle sizes and larger volumes of solids when compared to sand filters. The cyclonic and sand filter separation techniques are considered complimentary and present a challenge to the well test service company in making an investment decision on one technique or the other without prior knowledge of the well conditions. The Hunting Interchangeable Wellhead Desander features a dual pot system with interchangeable cyclone separators and sand filters offering the unique benefit of system configuration with both techniques to cover a wider range of well conditions from a single package. The Hunting cyclonic technology has been independently flow loop tested to verify solids separation performance. For technical information see page 41 Interchangeable Wellhead Desander

21 Sand Filter Configuration The sand filter is set up in the Type A configuration. 21 Cyclone Configuration The sand filter is removed, the cyclone separation inserted and the pipework configured for cyclone operation. The Hunting Cyclonic Desander Efficiency Calculator is an excel based software tool designed to aid our customers in selecting the most appropriate wellhead desanding method for their well test application. The tool is based on published correlations and has been verified against both a CFD simulation of the Hunting cyclone and 3rd party flow loop tests. The efficiency calculator allows our customers to run multiple scenarios varying inputs such as oil and gas flow rates, fluid properties and sand properties in order to evaluate their impact on solids separation performance.

22

23 WELL TESTING EQUIPMENT Hunting s extensive Well Testing product portfolio includes Heat Exchangers, Choke Manifolds, Plug Catchers and Piping Packages. Hunting s dedicated and experienced Well Testing division is committed to helping their customers improve well productivity in the most challenging environments. 23 Choke Manifold Wellhead Plug Catcher Heat Exchanger (Standard Type) Heat Exchanger (Container Type) Vertical Surge Tank Piping, Cross-overs And Instrumentation Packages

24 Well Testing Well Testing Equipment 24 Choke Manifolds Product Code WCM FEATURES Three flow paths through either a fixed or adjustable choke box or the full-bore bypass Low-torque metal-to-metal sealing on all gate valves Incorporates pressure ports and thermo-wells both upstream and downstream of the chokes Isolation valves fitted both upstream and downstream of the chokes Integral forklift pockets and four-point lifting sling provide safe handling options BENEFITS Controls and reduces well pressure upstream of process equipment Allows rapid fixed choke change-outs while the well remains flowing Facilitates fluid sampling and both wellhead pressure and temperature measurement Maximum operational flexibility with three flow-paths The Choke Manifold is the primary well pressure and flow control package used during both offshore and onshore well testing, frac flow-back, well clean-up and early production operations. Choke Manifolds Hunting can engineer, design and manufacture any choke manifold to the customer s specific need s including multiple valve and choke configurations, incorporating single or double pressure barrier philosophy and according to various industry-standard pressure and temperature ratings, pipe diameters and service requirements. The Hunting standard choke manifold has three flow paths through: A fixed choke that provides accurate flow control for flow rate measurement under stable conditions. An adjustable choke used during well clean-up or drawdown operations until a stable flow condition has been achieved. A full-bore bypass that can be used when choking downstream at the heater or in open-flow conditions. For technical information see page 42

25 Adjustable Choke Used during production clean up prior to establishing stable flow conditions. 25 Full-Bore Bypass Valve Allows choking of the well at the heat exchanger.

26 Well Testing Well Testing Equipment 26 Wellhead Plug Catcher Product Code WPC FEATURES Catcher line with internal perforated pipe By-pass line Optional drain line for debris removal In-line perforated pipes in various sizes BENEFITS Prevents damage and plugging of the downstream equipment Allows collection, inspection and measurement of larger well debris The Plug Catcher is designed to remove larger pieces of well debris from the well effluent during operations such as frac flowback, sand consolidation testing and completion clean-up after perforating or drilling out a bridge plug. It is positioned upstream of the wellhead sand separator or choke manifold to avoid damage and plugging of the downstream process. Wellhead Plug Catcher The Hunting Plug Catcher consists of a horizontal mounted manifold with a catcher chamber with an internal perforated pipe to collect debris and a by pass line to allow the screen to be isolated, depressurised and the debris to be collected and measured as required. The perforating pipe is available in several sizes depending on the type of well debris to be removed. The drain feature allows debris such as frac balls to be removed without removing the perforated pipe. Hunting plug catchers are available in a range of sizes, working pressures and configurations and can be customized to the clients requirements including dual catcher line designs to allow continuous debris removal and various sizes of perforated pipes. For technical information see page 43

27 Support Beam For screen replacement. Catcher Vessel 27 Quick Union or Hub Vessel entrance In-Line Perforated Pipe Catches debris and perforations can be sized according to custiomer specifications.

28 Well Testing Well Testing Equipment 28 Heat Exchanger (Standard Type) Product Code SHE-S FEATURES Internal tubing coil for effluent flow inside pressurised steam outer shell Automatic temperature control Choke between inlet and outlet to allow preheating of effluent Bypass manifold to avoid erosion in coils during well clean-up Steam trap with steam condensate outlet Rock-wool insulation on outer shell with aluminium jacket Spares toolbox mounted in skid BENEFITS Improved separation efficiency through viscosity reduction and breaking emulsions Avoiding flow restriction from gas hydrate formation Enabling well test operations where indirect-fired heaters are not permitted The Heat Exchanger (Standard Type) is a skidmounted steam vessel which contains a high pressure coil and choke through which the well stream can be diverted upstream of the separator. A separate steam generator supplies a constant flow of steam in contact with the coil to raise the temperature of the well effluent to prevent hydrate formation from plugging or restricting the flow and to improve separation and burner efficiency by reducing fluid viscosity and breaking down emulsions. Hunting provides a customised design, taking account of thermal design features, high/low pressure limits, temperature range, product mix and fluid flow capacity. Hunting s manufacturing flexibility enables them to supply heat exchangers for a variety of volume requirements. The temperature of the well effluent downstream of the heat exchanger is monitored through a controlvalve which then varies the steam flow into the vessel to maintain a pre-set temperature. Heat Exchanger (Standard Type) For technical information see page 44

29 Manual Choke Is located between the two coils in order to have the fluid pre-heated to prevent the formation of hydrates. 29 Pressure Relief Valve The pressure relief valve is transport inside the frame and installed on the heat exchanger vessel prior to operations. By-Pass Valve Isolates and by-passes internal coil during clean-up operations.

30 Well Testing Well Testing Equipment 30 Heat Exchanger (Container Type) Product Code SHE-C FEATURES Internal tubing coil for effluent flow inside pressurised steam outer shell Automatic temperature control Choke between inlet and outlet to allow preheating of effluent Bypass manifold to avoid erosion in coils during well clean-up Steam trap with steam condensate outlet Rock-wool insulation on outer shell with aluminium jacket Spares toolbox mounted in skid BENEFITS Improved separation efficiency through viscosity reduction and breaking emulsions Avoiding flow restriction from gas hydrate formation Enabling well test operations where indirect-fired heaters are not permitted Packaged in industry standard 20 ft shipping container skid The Heat Exchanger Container Type is a skidmounted steam vessel which contains a high pressure coil and choke through which the well stream can be diverted upstream of the separator. The Container is designed to be shipped and handled like a standard 20 ft shipping container lowering the cost of transportation. A separate steam generator supplies a constant flow of steam in contact with the coil to raise the temperature of the well effluent to prevent hydrate formation from plugging or restricting the flow and to improve separation and burner efficiency by reducing fluid viscosity and breaking down emulsions. Hunting provides a customised design, taking account of thermal design features, high/low pressure limits, temperature range, product mix and fluid flow capacity. Hunting s manufacturing flexibility enables them to supply heat exchangers for a variety of volume requirements. The temperature of the well effluent downstream of the heat exchanger is monitored through a controlvalve which then varies the steam flow into the vessel to maintain a pre-set temperature. Heat Exchanger (Container Type) For technical information see page 45

31 Insulated Vessel Aluminium jacket protect rockwool insulation on vessel steam. 31 Shipping Frame 20ft shipping frame meets industry shipping container standard to reduce cost and complexity of shipping and handling. Internal Adjustable Choke Internal adjustable choke on tubing coil allows pre-heating of well effluent upstream of choke.

32 Well Testing Well Testing Equipment 32 Vertical Surge Tank Product Code VST-A FEATURES Pressure retaining storage vessel to eliminate gas venting Can be used as second stage separator Single or twin compartment Measures liquid flow rates, shrinkage and meter factors Level monitoring by sight glass or magnetic indicators By-pass manifold allows isolation from process flow Access for internal inspection and maintenance High and low level alarm in each compartment Sampling, pressure and temperature ports BENEFITS Improves oil and gas separation when a longer retention time is required Pressurized storage improves burner efficiency during production disposal Eliminates atmospheric venting during H2S production operations The Hunting vertical surge tank (VST) is a low-pressure vessel designed to store liquid hydrocarbons prior to disposal during both offshore and onshore well testing and clean-up operations. Vertical Surge Tank Positioned downstream of the separator liquid outlet the VST is used to measure liquid flow rates and the combined shrinkage and meter factor. It can also be used as a second stage separator where a longer retention time is required. A pressure relief valve and a high and low level alarm system prevent overpressurization and over-filling of the vessels during operations. The VST can be manufactured with either a double or single compartment with either a sight glass or magnetic indicators to monitor liquid levels. The Hunting VST is mounted in a protective frame manufactured according to the requirements of Det Norske Veritas (DNV) and is designed for vertical operation and horizontal transportation. For technical information see page 46

33 Pressure Relief Valve Prevents over pressurisation of the vessel during operations by venting gas through the installation's LP line. 33 Manhole Cover Allows vessel internal access for cleaning, maintenance, inspecition and repair.

34 Well Testing Well Testing Equipment Piping, Crossovers and Instrumentation Packages FEATURES Dedicated and experienced well test equipment fabrication service Certification and Testing according PED 97/23/EC / ASME B31.3 / NACE BENEFITS On-time delivery reducing operational impact High quality fabrication up to the latest industry standards Well Testing, frac flowback and clean-up operations both offshore and onshore need customised piping, cross-over and instrumentation packages to be professionally fabricated, often at very short notice, where any delay has a potentially high impact on the cost of the operation and reputation of the well testing service provider. 34 Building on more than 30 years industry experience, Hunting has managed the inventory of critical components, such as pipe connectors, and developed in-house skills in welding and fabrication to establish a reputation for outstanding on-time delivery for this niche service. Hunting can provide a wide range of packages according to the customer s requirements including Certification and Testing in accordance with PED 97/23/EC / ASME B31.3 / NACE. DNV-OS-E101. Piping Packages Configurations Flow-Lines Elbows Cross-Overs Data Headers Tee s Y-Pieces Instrument Flanges Cross-blocks Test Caps Connections API & ASTM Flanges API Hubs Grayloc & Vector Hubs FMC & Anson Hammer Union from Fig 206 to 2202 Supplies Gaskets Seal Rings Stud-bolts API Clampsets Grayloc & Vector Clampsets Protectors Crossover Packages Any combination of the connectors and more. Instrumentation Packages Pressure Gauges Block and Bleed Temperature Gauges Needle Valves

35 Hunting can provide a wide range of packages according to the customer s requirements including Certification and Testing in accordance with PED 97/23/EC / ASME / B31.3 / NACE / DNV-OS-E

36 TECHNICAL INFORMATION Dual Pot Sand Filter (Type A) PRODUCT CODE DSF-A Model Hunting DSF-A 5K Hunting DSF-A 10K Hunting DSF-A 15K Hunting DSF-A 20K Service H2S H2S H2S H2S Fluid Class DD DD DD DD Working Pressure psi [bar] 5,000 [345] 10,000 [690] 15,000 [1035] 20,000 [1379] Working Temperature C [ F] -29 [0] up to 180 [350] -29 [0] up to 180 [350] -29 [0] up to 180 [350] -29 [0] up to 180 [350] Filter Sizes [mu] 100 up to up to up to up to 800 Filter Volume - liter 47 liter 47 liter 47 liter 47 liter Filter Flow Direction inside outside inside outside inside outside inside outside Maximum Filter ΔPpsi [bar] 1,500 [100] 1,500 [100] 2,755 [190] 2,755 [190] Flow Capacity (1) Gas, Mmscf [m³ / day] 25 [ ] 50 [ ] 75 [ ] 100 [ ] Oil, bbls /day Standard Connections (2) Gas / Oil Inlet API Flange 3-1/8 5K API Flange 3-1/16 10K API Flange 3-1/16 15K API Flange 3-1/16 20K 36 Gas / Oil Outlet API Flange 3-1/8 5K API Flange 3-1/16 10K API Flange 3-1/16 15K API Flange 3-1/16 20K Drain Union 2" Fig.1002 Union 2" Fig.1502 Union 2" Fig.2202 API Flange 2-1/16 20K Operational Footprint LxB cm 214 x x x x 250 Transport Size LxBxH cm 386 x 214 x 263 Optional 20ft Container Skid (3) 410 x 214 x 263 Optional 20ft Container 429 x 229 x x 300 x 250 Skid (3) Weight, kg [lbm] 8000 [20,944] [20,944] [33,700] ± [44,095] Certifications Design Type Approval Type Approval Type Approval DVR Manufacturing Declaration of Conformity Declaration of Conformity Declaration of Conformity Declaration of Conformity Documentation Quality File Quality File Quality File Quality File PED 97/23/EC PED 97/23/EC PED 97/23/EC PED 97/23/EC ASME B31.3 ASME B31.3 ASME B31.3 ASME B31.3 Applicable Codes ASME VIII div.2 ASME VIII div.2 ASME VIII div.3 ASME VIII div.3 API 6A API 6A API 6A API 6A NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) DNV DNV DNV DNV NOTES (1) Flow capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements. (3) Hunting has a Dual Pot Sand Filter Design inside a 20ft Container Skid.

37 TECHNICAL INFORMATION Dual Pot Sand Filter (Type AH) DSF-AH PRODUCT CODE Model Hunting DSF-AH 5K Hunting DSF-AH 3-1/16 10K Hunting DSF-AH 4-1/16 10K Service H2S H2S H2S Fluid Class DD DD DD Working Pressure psi [bar] 5,000 [345] 10,000 [690] 10,000 [690] Working Temperature C [ F] -29 [0] up to 180 [350] -29 [0] up to 180 [350] -29 [0] up to 180 [350] Filter Sizes [mu] 100 up to up to up to 800 Filter Volume - liter 47 liter 47 liter 47 liter Filter Flow Direction inside outside inside outside inside outside Maximum Filter ΔPpsi [bar] 1,500 [100] 1,500 [100] 1,500 [100] Flow Capacity (1) Gas, Mmscf [m³ / day] 50 [ ] 50 [ ] 100 [ ] Oil, bbls /day ,000 Standard Connections (2) Gas / Oil Inlet API Flange 5-1/8 5K API Flange 3-1/16 10K API Flange 4-1/16 10K Gas / Oil Outlet API Flange 5-1/8 5K API Flange 3-1/16 10K API Flange 4-1/16 10K Drain Union 3" Fig.1502 Union 3" Fig.1502 Union 3" Fig Operational Footprint LxB cm 425 x x x 245 Transport Size LxBxH cm 425 x 245 x x 245 x x 245 x 300 Weight, kg [lbm] [26.455] [30.864] [30.864] Certifications Design Type Approval Type Approval Type Approval Manufacturing Declaration of Conformity Declaration of Conformity Declaration of Conformity Documentation Quality File Quality File Quality File PED 97/23/EC PED 97/23/EC PED 97/23/EC ASME B31.3 ASME B31.3 ASME B31.3 Applicable Codes ASME VIII div.2 ASME VIII div.2 ASME VIII div.2 API 6A API 6A API 6A NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) DNV DNV DNV NOTES (1) Flow capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements.

38 TECHNICAL INFORMATION Dual Pot Sand Filter (Type B) PRODUCT CODE DSF-B Model Hunting DSF-B 10K Hunting DSF-B 10K HV Service H2S H2S Fluid Class DD DD Working Pressure psi [bar] 10,000 [690] 10,000 [690] Working Temperature C [ F] -29 [0] up to 180 [350] -29 [0] up to 121 [250] Filter Sizes [mu] 100 up to up to 800 Filter Volume - liter 62 liter 82 liter Filter Flow Direction outside inside outside inside Maximum Filter ΔPpsi [bar] 1,500 [100] 1,500 [100] Flow Capacity (1) Gas, Mmscf [m³ / day] 50 [ ] 100 [ ] Oil, bbls /day Standard Connections (2) Gas / Oil Inlet API Flange 3-1/16 10K API Flange 4-1/16 10K 38 Gas / Oil Outlet API Flange 3-1/16 10K API Flange 4-1/16 10K Drain Union 2" Fig.1502 Union 2" Fig.1502 Operational Footprint LxB cm 240 x x 280 Transport Size LxBxH cm 402 x 240 x x 250 x 280 Weight, kg [lbm] [24.250] [33.069] Certifications Design Type Approval DVR Manufacturing Declaration of Conformity Declaration of Conformity Documentation Quality File Quality File PED 97/23/EC PED 97/23/EC ASME B31.3 ASME B31.3 Applicable Codes ASME VIII div.2 API 6A ASME VIII div.2 API 6A NACE MR (ISO ,-2) NACE MR (ISO ,-2) DNV DNV NOTES (1) Flow capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements.

39 TECHNICAL INFORMATION Dual Pot Sand Filter (Type B-HPHT) DSF-B-HPHT PRODUCT CODE Model Service Fluid Class Hunting DSF-B 4-1/16 15K H2S DD Working Pressure psi [bar] 15,000 [1035] Working Temperature C [ F] -29 [0] up to 180 [350] Filter Sizes [mu] 100 up to 800 Filter Volume - liter Filter Flow Direction 82 liter inside outside Maximum Filter ΔPpsi [bar] 1,800 [125] Flow Capacity (1) Gas, Mmscf [m³ / day] 120 [ ] Oil, bbls /day Standard Connections (2) Gas / Oil Inlet Gas / Oil Outlet Water Flush Drain Operational Footprint LxB cm Transport Size LxBxH cm API Flange 5-1/8 15K API Flange 5-1/8 15K API Flange 2-1/6 15K API Flange 3-1/6 15K 515 x 290 (Base frame) 2x 20ft Container (619x260x290) + Base frame 39 Weight, kg [lbm] 2x [2x ] Certifications Design Manufacturing Documentation Type Approval Declaration of Conformity Quality File PED 97/23/EC ASME B31.3 ASME VIII div.3 Applicable Codes API 6A NACE MR (ISO ,-2) DNV DNV-OS-E101 NORSOK D-007, Z-015 NOTES (1) Flow capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements.

40 TECHNICAL INFORMATION Cyclonic Wellhead Desander PRODUCT CODE CWD Model Service Fluid Class Hunting CWD 10K H2S DD Working Pressure psi [bar] 10,000 [690] Working Temperature C [ F] -29 [0] up to 180 [350] Sand Storage Volume, liter 2x 200 liter Flow Capacity (1) Gas, Mmscf [m³ / day] 50 [ ] Oil, bbls /day 5000 Standard Connections (2) Unit Inlet Cyclone Inlet Drain API Flange 4-1/16 10K API Flange 3-1/16 10K Union 2" Fig.1502 Operational Footprint, LxB cm 244 x Transport Size, LxBxH cm Weight, kg [lbm] 16,000 [20,944] 6025 x 244 x 244 (20ft Container Skid) Certifications Design Manufacturing Documentation Type Approval Declaration of Conformity Quality File PED 97/23/EC ASME B31.3 Applicable Codes ASME VIII div.2 API 6A NACE MR (ISO ,-2) DNV NOTES (1) Flow capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements.

41 TECHNICAL INFORMATION Interchangeable Wellhead Desander IWD PRODUCT CODE Model DSF-A 10K Cyclone upgrade Hunting IWD 10K Service H2S H2S Fluid Class DD DD Working Pressure psi [bar] 10,000 [690] 10,000 [690] Working Temperature C [ F] -29 [0] up to 180 [350] -29 [0] up to 180 [350] Filter Sizes [mu] 100 up to up to 800 Filter Volume - liter 2x 47 liter 2x 47 liter Cyclone Sand Volume - liter 2x 62 liter 2x 62 liter Filter Flow Direction inside outside inside outside Maximum Filter ΔPpsi [bar] 1,500 [100] 1,500 [100] Flow Capacity (1) Gas, Mmscf [m³ / day] 50 [ ] 50 [ ] Oil, bbls /day Standard Connections (2) Gas / Oil Inlet API Flange 3-1/16 10K API Flange 4-1/16 10K Gas / Oil Outlet API Flange 3-1/16 10K API Flange 3-1/16 10K 41 Drain Union 2" Fig.1502 Union 2" Fig.1502 Operational Footprint LxB cm 263 x x 244 Transport Size LxBxH cm 410 x 214 x 263 Optional for 20ft Container Skid(3) 6025 x 244 x 244 (20ft Container Skid) Weight, kg [lbm] [20,944] [26,455] Certifications Design Type Approval Type Approval Manufacturing Declaration of Conformity Declaration of Conformity Documentation Quality File Quality File PED 97/23/EC PED 97/23/EC ASME B31.3 ASME B31.3 Applicable Codes ASME VIII div.2 API 6A ASME VIII div.2 API 6A NACE MR (ISO ,-2) NACE MR (ISO ,-2) DNV DNV NOTES (1) Flow capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements. (3) Hunting has a Dual Pot Sand Filter Design inside a 20ft Container Skid.

42 TECHNICAL INFORMATION Choke Manifold PRODUCT CODE WCM Model WCM 5K WCM 10K WCM 15K WCM 20K Service H2S H2S H2S H2S Fluid Class DD DD DD DD Working Pressure psi [bar] 5,000 [345] 10,000 [690] 15,000 [1035] 20,000 [1379] Working Temperature C [ F] -29 [0] up to 180 [350] -29 [0] up to 180 [350] -29 [0] up to 180 [350] -29 [0] up to 180 [350] Flow Capacity (1) Gas, Mmscf [m³ / day] 25 [ ] 50 [ ] 75 [ ] 75 [ ] Oil, bbls /day Standard Connections (2) Gas / Oil Inlet API Flange 3-1/8 5K API Flange 3-1/16 10K API Flange 3-1/16 15K API Flange 3-1/16 20K Gas / Oil Outlet API Flange 3-1/8 5K API Flange 3-1/16 10K API Flange 3-1/16 15K API Flange 3-1/16 20K 42 Operational Footprint LxB cm Transport Size LxBxH cm Weight, kg [lbm] Certifications Dimensions and weights are depending on model type: Single or Double Block Gate Valves Size of connections, 3-1/16, 4-1/16 etc. Offshore or onshore transport Skid Hunting also has compact models with low footprint Ask Hunting for actual weights and dimensions. Design Type Approval Type Approval Type Approval DVR Manufacturing Declaration of Conformity Declaration of Conformity Declaration of Conformity Declaration of Conformity Documentation Quality File Quality File Quality File Quality File PED 97/23/EC PED 97/23/EC PED 97/23/EC PED 97/23/EC ASME B31.3 ASME B31.3 ASME B31.3 ASME B31.3 Applicable Codes API 6A API 6A API 6A API 6A NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) Optional with DNV Optional with DNV Optional with DNV Optional with DNV NOTES (1) Flow capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements.

43 TECHNICAL INFORMATION Wellhead Plug Catcher WPC PRODUCT CODE Model WPC 5-1/8 5K WPC 3-1/16 10K WPC 4-1/16 10K Service H2S H2S H2S Fluid Class DD DD DD Working Pressure psi [bar] 5,000 [345] 10,000 [690] 10,000 [690] Working Temperature C [ F] -29 [0] up to 180 [350] -29 [0] up to 180 [350] -29 [0] up to 180 [350] Filter Sizes [mu] As per customer requirement As per customer requirement As per customer requirement Flow Capacity (1) Gas, Mmscf [m³ / day] 50 [ ] 50 [ ] 100 [ ] Oil, bbls /day 15, ,000 Standard Connections (2) Gas / Oil Inlet API Flange 5-1/8 5K API Flange 3-1/16 10K API Flange 4-1/16 15K Gas / Oil Outlet API Flange 5-1/8 5K API Flange 3-1/16 10K API Flange 4-1/16 15K Drain API Flange 2-1/16 5K API Flange 2-1/16 5K API Flange 2-1/16 5K Operational Footprint LxB cm 400 x 200 Sizes can be customized 400 x 200 Sizes can be customized 526 x 200 Sizes can be customized Transport Size LxBxH cm 400 x 200 x 150 Sizes can be customized 400 x 200 x 150 Sizes can be customized 526 x 200 x 150 Sizes can be customized 43 Weight, kg [lbm] 5000 [11,023] 6000 [13,227] 7000 [15,432] Certifications Design DVR DVR DVR Manufacturing Declaration of Conformity Declaration of Conformity Declaration of Conformity Documentation Quality File Quality File Quality File PED 97/23/EC PED 97/23/EC PED 97/23/EC ASME B31.3 ASME B31.3 ASME B31.3 Applicable Codes API 6A API 6A API 6A NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) Optional DNV Optional DNV Optional DNV NOTES (1) Flow capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements.

44 TECHNICAL INFORMATION Heat Exchanger (Standard Type) PRODUCT CODE SHE-S Model Hunting SHE-S 5K Hunting SHE-S 10K 3 bore Hunting SHE-S 10K 4 bore Hunting SHE-S 15K Service H2S H2S H2S H2S Fluid Class DD DD DD DD Coil 4 XXS 4 XXS 5 XXS 5 x3 Working Pressure, psi [bar] Coil 5,000 [345] 10,000 [690] 10,000 [690] 15,000 [1035] Steam Vessel 150 [10,3] 150 [10,3] 150 [10,3] 150 [10,3] Working Temperature - C [ F] -20 [0] up to 180 [350] -20 [0] up to 180 [350] -20 [0] up to 180 [350] -20 [0] up to 180 [350] Heating Capacity (1) - MMBtu/h 4,2 4,2 4,2 4,2 Standard Connections (2) Gas / Oil Inlet API Flange 3-1/8 5K API Flange 3-1/16 10K API Flange 4-1/16 10K API Flange 3-1/16 15K Gas / Oil Outlet API Flange 3-1/8 5K API Flange 3-1/16 10K API Flange 4-1/16 10K API Flange 3-1/16 15K Steam Inlet Union 2 Fig.206 Union 2 Fig.206 Union 2 Fig.206 Union 2 Fig.206 Steam oulet Union 2 Fig.206 Union 2 Fig.206 Union 2 Fig.206 Union 2 Fig Operational Footprint LxB cm 719 x x x x 220 Transport Size LxBxH cm 719 x 198 x 259 cm 719 x 198 x x 198 x x 220 x 263 Weight, kg [lbm] [26,445] [26,445] [26,445] [35,273] Certifications Design Type Approval Type Approval Type Approval Type Approval Manufacturing Declaration of Conformity Declaration of Conformity Declaration of Conformity Declaration of Conformity Documentation Quality File Quality File Quality File Quality File PED 97/23/EC PED 97/23/EC PED 97/23/EC PED 97/23/EC ASME B31.3 ASME B31.3 ASME B31.3 ASME B31.3 Applicable Codes ASME VIII div.1 ASME VIII div.1 ASME VIII div.1 ASME VIII div.1 API 6A API 6A API 6A API 6A NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) DNV DNV DNV DNV NOTES (1) Heating capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements.

45 TECHNICAL INFORMATION Heat Exchanger (Container Type) SHE-C PRODUCT CODE Model Hunting SHE-C 5K Hunting SHE-C 10K 3 bore Hunting SHE-S 10K 4 bore Hunting SHE-S 15K Service H2S H2S H2S H2S Fluid Class DD DD DD DD Coil 4 XXS 4 XXS 5 XXS 5 x3 Working Pressure, psi [bar] Coil 5,000 [345] 10,000 [690] 10,000 [690] 15,000 [1035] Steam Vessel 150 [10.3] or 230 [15.8] 150 [10.3] or 230 [15.8] 150 [10,3] 150 [10,3] Working Temperature - C [ F] -20 [0] up to 180 [350] -20 [0] up to 180 [350] -20 [0] up to 180 [350] -20 [0] up to 180 [350] Heating Capacity (1) - MMBtu/h 4,2 4,2 4,2 4,2 Standard Connections (2) Gas / Oil Inlet API Flange 3-1/8 5K API Flange 3-1/16 10K API Flange 4-1/16 10K API Flange 3-1/16 15K Gas / Oil Outlet API Flange 3-1/8 5K API Flange 3-1/16 10K API Flange 4-1/16 10K API Flange 3-1/16 15K Steam Inlet Union 2 Fig.206 Union 2 Fig.206 Union 2 Fig.206 Union 2 Fig.206 Steam oulet Union 2 Fig.206 Union 2 Fig.206 Union 2 Fig.206 Union 2 Fig.206 Operational Footprint LxB cm 6055 x x x x 220 Transport Size LxBxH cm 6055 x 244 x ft Container Skid 6055 x 244 x ft Container Skid 719 x 198 x x 220 x Weight, kg [lbm] [26,660] [26,660] [26,445] [35,273] Certifications Design Type Approval Type Approval Type Approval Type Approval Manufacturing Declaration of Conformity Declaration of Conformity Declaration of Conformity Declaration of Conformity Documentation Quality File Quality File Quality File Quality File PED 97/23/EC PED 97/23/EC PED 97/23/EC PED 97/23/EC ASME B31.3 ASME B31.3 ASME B31.3 ASME B31.3 Applicable Codes ASME VIII div.1 ASME VIII div.1 ASME VIII div.1 ASME VIII div.1 API 6A API 6A API 6A API 6A NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) NACE MR (ISO ,-2) DNV DNV DNV DNV NOTES (1) Heating capacity is dependant on many factors. Please contact Hunting for advice. (2) Connections cross-overs can be added as per customer requirements.

46 TECHNICAL INFORMATION Vertical Surge Tank PRODUCT CODE VST-A Model Service Fluid Class Hunting VST H2S DD Working Pressure psi [bar] Piping psi [bar] 150 [10.3] Vessel psi [bar] 150 [10.3] Working Temperature C [ F] -29 [-20] up to 121 [250] Storage Capacity m³ 16 Standard Connections (1) 46 Gas / Oil Inlet Oil Outlet Gas Outlet Drain Safety Relief Optional Connections (1) Steam Inlet Steam oulet Union 3 Fig.602 Union 3 Fig.602 Union 4 Fig.602 Union 3 Fig.602 Union 4 Fig.602 Union 2 Fig.206 Union 2 Fig.206 Operational Footprint, LxB cm 282 x 240 Transport Size, LxBxH cm 7440 x 240 x 282 Weight, kg [lbm] [26,660] Certifications Design Manufacturing Documentation Type Approval Declaration of Conformity Quality File PED 97/23/EC ASME B31.3 ASME VIII div.1 Applicable Codes API 6A NACE MR (ISO ,-2) DNV DNV-OS-E101 NOTES (1) Connections can be changed as per customer requirements.

47 / HUNTING012_v1

48 Hunting All Rights Reserved