A RANGE OF QUALITY PRIMERS FOR TIMBER AND MDF MADE FOR THE JOINERY AND SHOPFITTING TRADES FOR SPRAY APPLICATIONS

Transcription

1 A RANGE OF QUALITY PRIMERS FOR TIMBER AND MDF MADE FOR THE JOINERY AND SHOPFITTING TRADES FOR SPRAY APPLICATIONS ACRYLIC PRIMER SPRAYABLE INTERIOR (43APSI) ACRYLIC PRIMER SPRAYABLE INTERIOR/EXTERIOR (43AP) UNIVERSAL WOOD PRIMER (OB) SPRAYING INTERIOR EXTERIOR (44SP25) ACRYLIC PRIMER SPRAYABLE (43APSI AND 43AP) CONSTRUCTION CHEMICALS HIGH OPACITY ACRYLIC COPOLYMER PRIMER IS A HIGH QUALITY MICRO POROUS, QUICK DRYING SPRAY PRIMER. INTENDED USES 43APSI Water based primer/undercoat for interior use. Supplied ready for use with spray applications, automatic brush and vacuum timber coaters. Foam resistant with good 'flow' on application. Can also be brush applied. WATER THINNABLE. TECHNICAL INFORMATION 43APSI / 43AP Block resistant on drying. Excellent opacity in a Single coat, fast drying and low odour. Coverage m2 per kg depending upon porosity and surface texture. Drying time at 200C: Touch Dry - 20 minutes Firm Dry hours Overcoat - 3 hours with water based coatings, over night with solvent based coating. Use only in well ventilated areas. In case of contact with eyes rinse immediately with plenty of water and seek medical attention. PACKED IN 30kg PLASTIC BUCKETS APPLICATION DETAILS 43APSI and 43AP Chris Butler Mouldings use Construction Chemicals Acrylic spray primer for ease, speed of coverage and quick drying. cbjoinery@btinternet.com Ambient Conditions Surface Preparation Above 5 0 C, and less than 80% relative humidity. Ensure surfaces are clean and dry. 75 TOWN GREEN STREET LEICESTER LE7 7NW TEL: FAX:

2 Notes: ACRYLIC PRIMER SPRAYABLE (43APSI AND 43AP) Knots Water based wood primers are essentially self knotting. Once fully dry Primer E43 Silver White Primer is unaffected by resinous knots, whereas oil based primers allow resinous material to bleed through the paint film. Timber which is heavily knotted, or particularly resinous, should be spot primed with E43 over the knots and allowed to dry before overall painting. Shrunken or cracked knots should be filled as necessary prior to painting. Microporosity. E34 E43 Once dry, E43 White Primer has microporous properties, which allows individual water molecules to pass slowly through the primer (but not water droplets), letting moisture vapour permeate out of timber and allowing the wood to breathe. The benefits of microporosity will be lost if any other coating within a paint system is not microporous. E34 AND E43 should not be used on timber with high moisture content prior to painting, and in use will not allow saturated timber to dry out. Under these circumstances premature coating failure may occur. ACRYLIC WHITE WOOD PRIMER INTERIOR/EXTERIOR (43AP) INTENDED USES CONSTRUCTION CHEMICALS HIGH OPACITY MODIFIED ACRYLIC COPOLYMER PRIMER IS A HIGH QUALITY MICRO POROUS, QUICK DRYING PRIMER FOR INTERIOR AND EXTERIOR USE, Water based microporous primer/undercoat for use on wood/mdf/hardboard etc. Supplied ready for use for spraying, automatic brush and vacume timber coaters. Foam resistant with good flow on application. Block resistant on drying and self knotting. Carefully selected blend of pigments ensures denibbing without clogging and ease of sanding by the end user. Excellent opacity in a single coat, fast drying and low odour. May be over coated with emulsion or white-spirit based decorative coatings. Some hard woods may need wiping over with white spirit to remove any resins. STORAGE & HANDLING 43APSI AND 43AP Storage Under cover in the range C. Protect from frost. Pack Size 30kg. Shelf life 12 months in unopened containers when stored under cover in good conditions. Clean up Clean all equipment immediately with clean water. Using spray primer speeds up the priming process, typically a pallet of skirting like this would take 1 man a day to prime, by spaying this time has been reduced to 1 hour. Construction Chemicals spray primer is block resistant this means the primed timber can be quickly stacked without sticking.

3 OIL BASED WOOD PRIMER SPRAYING Full Description Product Type Colour HIGH OPACITY OIL BASED WOOD PRIMER EXTERIOR Modified Alkyd White INTENDED USES Primer for use on wood/mdf/hardboard etc. Excellent Opacity in a single coat. Fast drying. May de over coated with emulsion or solvent based decorative coatings. Some hard woods may need wiping over with white spirit to remove any resins. TECHNICAL INFORMATION Appearance of dried film Matt White. Method of application Brush. Conventional or airless spray. May require up to 10% Thinners to achieve optimum spray characteristics. Coverage Typically 8-12 m 2 per litre depending upon film thickness applied and surface profile, absorption etc. Drying time at 20 0 C (will vary with changes in temperature and air movement etc). Touch Dry 1 hour Firm Dry 4 hours Overcoat overnight. APPLICATION DETAILS Ambient Conditions Surface Preparation Above 5 0 C, and less than 80% relative humidity. Ensure surfaces are clean and dry. Ensure all preservatives (e.g. vac-vac) are fully dry before applying primer. Particular care should be taken when applied over water based preservatives. STORAGE & HANDLING Storage Under cover in the range C. Pack Size Product weight Shelf life Clean up 30kg 7.5kg. 1.5 kilos per litre. 12 months in unopened containers. Clean all equipment immediately with Thinners or White Spirit. SAFETY PRECAUTIONS A copy of the appropriate Health and Safety Data Sheet should be consulted prior to use. This can be faxed if required urgently. MSDS Ref, OIL BASED WOOD PRIMER All work involving application and use of this product should be performed in compliance with current health and safety standards and legislation. If in any doubt regarding the suitability for use of this product, consult Construction Chemicals for advice. 75 TOWN GREEN STREET LEICESTER LE7 7NW TEL: FAX:

4 SAFETY DATA SHEET CONSTRUCTION CHEMICALS WATER BASED WHITE WOOD PRIMER, SPRAYING 1. IDENTIFICATION OF THE SUBSTANCE/ PREPARATION AND THE COMPANY PRODUCT NAME SUPPLIER E34 White Water Based Wood/MDF Primer CONSTRUCTION CHEMICALS 75 TOWN GREEN ST LEICESTERSHIRE TELEPHONE: FAX: EMERGENCY: COMPOSITION/INFORMATION ON INGREDIENTS. This product does not contain substances presenting a health hazard within the meaning of the Chemicals (Hazard Information and Packaging for Supply) Regulations (CHIP). 3. HAZARDS IDENTIFICATION This product is not classified as dangerous for supply according to the CHIP regulations. 4 FIRST AID MEASURES GENERAL Keep affected person under observation. INHALATION Move the exposed person to fresh air at once. Perform artificial respiration if breathing has stopped. Keep the affected person warm and at rest. Get prompt medical attention. INGESTION DO NOT INDUCE VOMITING! NEVER MAKE AN UNCONSCIOUS PERSON VOMIT OR DRINK FLUIDS! Get medical attention. SKIN Remove affected person from source of contamination. Promptly wash contaminated skin with soap or mild detergent and water. Promptly remove clothing if soaked through and wash as above. Get medical attention if irritant persists after washing. EYES Promptly wash eyes with plenty of water while lifting the eyelids. Get medical attention. 5. FIRE FIGHTING MEASURES Extinguishing Media Thids material is not flammable. Use extinguishing media appropriate to surrounding fire. 6. ACCIDENTAL RELEASE MEASURES Contain and collect spillages with non combustible absorbent material, eg. Sand, earth, vermiculite, and place in containers. Do not allow to enter water courses. Clean preferably with a detergent. Avoid the use of solvents. 7. HANDLING AND STORAGE Handling: Avoid skin and eye contact. Smoking, eating and drinking should be prohibited in areas of use and storage. Storage: Store between 5 and 20 degrees centigrade in a dry, well ventilated place. Keep in closed, original container Page 1 of 2

5 8. EXPOSURE CONTROLS AND PERSONAL PROTECTION Ventilation Provide adequate ventilation. Hand protection Wear protective gloves. Eye protection Eye protection designed to guard against liquid splashes should be worn. Skin protection Cotton or cotton/synthetic overalls or coveralls are normally suitable. Grossly contaminated clothing should be removed and the skin washed with soap and water or a proprietary skin cleaner. 9 PHYSICAL AND CHEMICAL PROPERTIES APPEARANCE liquid ODOUR - faint SPECIFIC GRAVITY 1.5 SOLUBILITY IN WATER Miscible ph STABILITY AND REACTIVITY Stable under the recommended storage and handling conditions. In a fire, decomposition products such as carbon monoxide and carbon dioxide may be produced. 11 TOXICOLOGICAL INFORMATION HEALTH HAZARDS, GENERAL- this product is unlikely to harm health, given normal and proper handling and hygienic precautions. 12 ECOLOGICAL INFORMATION BIO ACCUMULATION Will not bioaccumulate. DEGRADABILITY Readily degradable. 13 DISPOSAL CONSIDERATIONS Do not allow into drains or water courses or where ground or surface water may be affected. Dispose of in accordance with local authority requirements. 14 TRANSPORT INFORMATION This product is not classified as dangerous for carriage. 15 REGULATORY INFORMATION This product is determined as not being dangerous according to CHIP regulations The information contained in this safety data sheet does not constitute the users own assessment of workplace risk as required by other health and safety legislation. The provisions of the Health and Safety at Work etc and the Control of Substances Hazardous to Health Regulations apply to the use of this product at work. 16. OTHER INFORMATION. This safety data sheet is provided in accordance with the provisions of Section 6 of the Health and Safety at Work, etc. act 1974, as amended by the Consumer Protection Act The product should not be used for purposes other than those shown in Section 1 without first referring to the supplier and obtaining written handling instructions. As the specific conditions of use are outside the supplier's control, the user is responsible for ensuring that the requirements of relevant legislation are complied with. The information contained in this safety data sheet is based on the present state of knowledge and current national legislation. It provides guidance on health, safety and environmental aspects of the product and should not be construed as any guarantee of technical performance or suitability for particular applications. Further information and advice can be found in: The Control of Substances Hazardous to Health Regulations 1988 (SI.1988:1657). The Manual Handling Operations Regulations 1992 (SI 1992:2793) The Environmental Protection (Duty of Care) Regulations 1992 (SI 1992:2839) E34 H&S. October Page 2 of 2