NOT CLASSIFIED AS HAZARDOUS ACCORDING TO CRITERIA OF NOHSC. International Beauty Supplies. 6e Narabang Way, Belrose NSW, Australia 2085

Transcription

1 1. IDENTIFICATION OF THE PREPARATION AND THE COMPANY Product name Product code Product use Company Address St. Tropez Bronzing Mist STBM** Spray Tanning Liquid International Beauty Supplies 6e Narabang Way, Belrose NSW, Australia 2085 Telephone number (02) Fax number (02) EMERGENCY TELEPHONE NUMBER Bill McKendrick Managing Director (BH) (02) (AH) HAZARDS IDENTIFICATION Not classified as hazardous according to criteria of NOHSC Not classified as a Dangerous Good according to the Australian Code for the Transport of Dangerous Goods by Road and Rail. Not classified as a Dangerous Good according to the International Air Transport Association (IATA) Dangerous Goods Regulations Page : Page 1 of 7

2 3. COMPOSITION / INFORMATION ON INGREDIENTS Component CAS Wg Water (Aqua) Dihydroxyacetone Ethoxydiglycol Penlylene Glycol naturally derived Glycerin Aloe Barbadensis Leaf Juice Extract PPG-5-Ceteth-20 Potassium Sorbate Phenoxyethanol Sodium Bisulfite Fragrance (Parfum) Benzyl Salicylate Cinnamal Cinnamyl Alcohol Citronellol Coumarin Eugenol Alpha-Isomethyl Ionone Geraniol Hexyl Cinnamal Hydroxycitronellal Isoeugenol Butylphenyl Methylpropianol Linalool Hydroxyisohexyl 3-Cyclohexene Carboxaldehyde Citric Acid Caramel Blue 1 (Cl 42000) Red 4 (Cl 14700) Yellow 5 (Cl 19140) Page : Page 2 of 7

3 4. FIRST AID MEASURES Route of exposure - Inhalation Remove victim to fresh air. Apply artificial respiration if indicated - Ingestion May cause abdominal distress. Seek medical attention if irritation persists - Eye Contact Immediately flush with clean, lukewarm water (low pressure), occasionally lifting eyelids. Seek Medical attention if irritation develops. - Skin Contact Non irritatin to the skin. - First aid facilities - Advice to doctor 5. FIRE-FIGHTING MEASURES Specific hazards Hazardous combustion products Suitable extinguishing media Carbon dioxide, dry chemical, foam or water spray Unsuitable extinguishing media Special protective equipment for fire fighters Page : Page 3 of 7

4 6. ACCIDENTAL RELEASE MEASURES Personal precautions: Before cleaning any spill or leak, individuals involved in spill cleanup must wear appropriate Personal Protective Equipment. Environmental precautions: Dispose of properly in accordance with local, state and federal regulations. Methods for cleaning up For small spills (e.g., < 5 Litres), wear appropriate personal protective equipment (e.g., goggles, gloves). Maximize ventilation (open doors and windows). Remove spilled material with absorbent material and place into appropriate closed container(s) for disposal. Dispose of properly in accordance with local, state and federal regulations. Wash all affected areas and outside of container with plenty of warm water and soap. Remove any contaminated clothing and wash thoroughly before reuse. For spills 5 Litres, deny entry to all unprotected individuals. Dike and contain spill with inert material (e.g., sand or earth). Transfer product to containers for recovery or disposal and solid diking material to separate containers for proper disposal. Remove contaminated clothing promptly and wash affected skin areas with soap and water. Keep spills and cleaning runoffs out of municipal sewers and open bodies of water. 7. HANDLING AND STORAGE Handling Avoid eye contact Storage Use and store in a cool, dry, well-ventilated location (e.g., local exhaust ventilation, fans). Do not store in damaged or unmarked containers or storage devices. Keep containers securely closed when not in use. Other information Spilled material may present a slipping hazard if left unattended. Clean all spills promptly. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Respiratory protection: Eye protection: Hand protection Body protection Exposure limits Engineering controls None required if used in a well-ventillated area, if in confined space without extraction unit protective face mask should be worn Avoid eye contact. Not required under normal conditions of use None required under normal conditions of use None required under normal conditions of use Page : Page 4 of 7

5 9. PHYSICAL AND CHEMICL PROPERTIES Appearance Odour ph Vapour pressure Vapour density Boiling point Melting point Solubility Specific gravity Flash point Flammability limits lower Flammability limits upper Ignition temperature Brownish-Black, Water-Thin Liquid Fragranced Soluble 25 C: STABILITY AND REACTIVITY Chemical stability Conditions to avoid Incompatible materials Hazardous decomposition products Hazardous reactions This product is stable Open flames, sparks, high heat and direct sunlight 11. TOXICOLOGICAL INFORMATION Toxicology data The product has not been tested for specific toxicity data Acute health hazards Ingestion Inhalation Skin Contact Eye Contact Chronic Health Hazards Page : Page 5 of 7

6 12. ECOLOGICAL INFORMATION Ecotoxicity Persistence and degradability Mobility There is no specific data available for this product There is no specific data available for this product There is no specific data available for this product 13. DISPOSAL CONSIDERATIONS Product and container disposal Dispose of properly in accordance with local, state and federal regulations. Special precautions for landfill or incineration 14. TRANSPORT INFORMATION Not classified as a Dangerous Good according to the Australian Code for the Transport of Dangerous Goods by Road and Rail Not classified as a Dangerous Good according to the International Air Transport Association (IATA) Dangerous Goods Regulations 15. REGULATORY INFORMATION Poisons Schedule AICS Status Labelling Risk phrases Safety phrases Page : Page 6 of 7

7 16. OTHER INFORMATION Initial preparation date April 1, 2005 Amendment date March 19, 2013 Reasons for change The information provided in this Material SafetyData Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text.end of MSDS. Page : Page 7 of 7