Revision Date: March 8, 2017 Version No.: 2 SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING

Transcription

1 SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING 1.1 Product Identifier Product Name JEESILC Relevant Identified Uses of the Substance or Mixture and Uses Advised Against Identified uses Cosmetic raw material 1.3 Details of the Supplier of the Safety Data Sheet Company JEEN International Corporation 24 Madison Road Fairfield, New Jersey Tel: Fax: info@jeen.com Website: Emergency telephone number (Chemtrec Int l Tel - Collect calls accepted) SECTION 2 HAZARDS IDENTIFICATION 2.1 Classification of the Substance or Mixture according to Regulation (EC) 1272/ Label Elements according to Regulation (EC) EU 1272/2008 Hazard pictogram Signal words Hazard statements Precautionary statements 2.3 Other Hazards known SECTION 3 COMPOSITION/INFORMATION ON INGREDIENTS 3.1 Substances Chemical characterization Cosmetic ingredients INCI Dimethicone CAS EC Exempt Concentration Mixture - SECTION 4 FIRST AID MEASURES 4.1 Description of First Aid Measures JEESILC 110 Page 1 of 5

2 If swallowed If inhaled If in eyes If on skin Other information No first aid should be needed. If discomfort occurs, obtain medical attention. Wash out mouth thoroughly with water do not induce vomiting seek medical attention. Short-term harmful health effects are not expected from vapor generated at ambient temperatures. If first aid is required, remove to fresh air; symptomatic treatment. Rinse immediately with plenty of water for at least 15 minutes; seek medical attention. Wash with plenty of soap and water, if irritation persists or develops, seek medical attention. Remove contaminated clothing and launder before reuse. Treat symptomatically SECTION 5 FIRE FIGHTING MEASURES 5.1 Flash Point >200 C by Pensky Martens closed cup. Auto-ignition Temp Flammability 5.2 Extinguishing Media Carbon dioxide (CO2) water spray. Dry chemical foam water can be used to cool fire exposed containers. 5.3 Protective Equipment for Fire-fighting Self-contained breathing apparatus and protective clothing should be worn in fighting fires involving chemicals. 5.4 Hazardous Decomposition Products Silicon dioxide. Carbon oxides and traces of incompletely burned carbon compounds. SECTION 6 ACCIDENTAL RELEASE MEASURES 6.1 Methods and Material for Containment Collect for disposal. Clean up remaining materials from spill with suitable and Cleaning Up absorbent. For large spills provide diking or other appropriate containment to keep material from spreading. If diked material can be pumped, store recovered material in appropriate container. Clean area as appropriate since some silicone material, even in small quantities, may present a slip hazard. Final cleaning may requirement steam, solvents, or detergents. Observe all federal, provincial and local regulations that may apply to the cleanup of this material. SECTION 7 HANDLING AND STORAGE 7.1 Precautions for Safe Handling Safety glasses and PBC gloves. 7.2 Conditions for Safe Storage, including Keep container closed. Product is non-hazardous any incompatibilities SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION 8.1 Engineering Controls Local Exhaust: should be needed. JEESILC 110 Page 2 of 5

3 General Ventilation: Recommended 8.2 Personal Protective Equipment for Handling Eyes: Use proper protection safety glasses as a minimum Skin: Washing at mealtime and end of shift is adequate Suitable Gloves: No special protection is needed Inhalation: No respiratory protection should be needed Suitable Respirator: should be needed 8.3 Personal Protective Equipment for Spills Eyes: Skin: Respirator: Precautionary Measures: Note: Use proper protection safety glasses as a minimum Washing at mealtime and end of shift is adequate No respiratory protection should be needed. Avoid eye contact. Keep container closed These precautions are for room temperature handling. Use at elevated temperatures or aerosol spray applications may require added precautions. SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES 9.1 Information on basic Physical and Chemical Properties Appearance: Clear Physical State: Liquid Odor: Mild ph: Specific Gravity Solubility in water insoluble Viscosity, cps 4,000 Melting Point Boiling Point > mm Vapor Pressure SECTION 10 STABILITY AND REACTIVITY 10.1 Chemical Stability Stable 10.2 Conditions to Avoid known 10.3 Hazardous Polymerization Known 10.4 Incompatible Materials known SECTION 11 - TOXICOLOGICAL INFORMATION 11.1 Information on Toxicological Effects No data available JEESILC 110 Page 3 of 5

4 SECTION 12 - ECOLOGICAL INFORMATION 12.1 Information on Ecological Effects No data available SECTION 13 - DISPOSAL CONSIDERATIONS 13.1 Disposal Treatment Methods Landfill and or incineration where permitted under Federal, Provincial or local laws. Observe all local, provincial and federal waste management regulations. SECTION 14 TRANSPORTATION INFORMATION 14.1 U.S. DOT Proper shipping name UN Number Primary class Subsidiary Risk Product ID. # Packing Group 14.2 IATA Not regulated SECTION 15 REGULATORY INFORMATION This product has been classified in accordance with the hazard criteria of the CPR and this MSDS contains all information required by CPR. TSCA Status All chemical substances in this material are included on or exempted from listing on the TSCA inventory chemical substances. WHMIS Classification Product is not subject to WHMIS regulations EPA SARA Title III Chemical Listings Section 302 extremely hazardous substances: Section 304 CERCLA Hazardous substances Section 311/312 Hazard class (40 CFR 370): Section 313 Toxic Chemicals (40 CFR 372) California Warming: Acute: No, Chronic: No, Pressure: No, Reactive: No This product contains the following chemical(s) listed by the State of California under the Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65) as being known to cause cancer, birth defects or other reproductive harm. known Massachusetts: No ingredients regulated by MA Right to know law present New Jersey CAS Number WT, % >60.0 Component Name Polydimethylsiloxane Pennsylvania CAS Number WT, % >60.0 Component Name: Polydimethylsiloxane SECTION 16 OTHER INFORMATION Health: 1 JEESILC 110 Page 4 of 5

5 Flammability: 2 Reactivity: 0 Personal Protection: C Disclaimer: As the conditions or methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of this product. Information contained herein is believed to be true and accurate but all statements or suggestions are made without warranty, expressed or implied, regarding accuracy of the information, the hazards connected with the use of the material or the results to be obtained from the use thereof. Compliance with applicable federal, state and local regulations remains the responsibility of the user JEESILC 110 Page 5 of 5