Apply safe welding practices This assessment resource supports the unit of competency MEM05052 Apply safe welding practices

Transcription

1 Apply safe welding practices This assessment resource supports the unit of competency MEM05052 Apply safe welding practices These materials were developed by Manufacturing Skills Australia.

2 These materials were developed by Manufacturing Skills Australia. Manufacturing Skills Australia With the exception of any material protected by a trade mark and where otherwise noted, all material presented in this document is provided under a Creative Commons Attribution-No Derivative Works 3.0 Australia licence. Disclaimer This work is the result of consultations with Australian industry participants. It is a collaborative view and does not necessarily represent the view of Manufacturing Skills Australia or any specific body. For the sake of brevity it may omit factors which could be pertinent in particular cases. While care has been taken in the preparation of this material, Manufacturing Skills Australia and the original developer do not warrant that any licensing or registration requirements specified here are either complete or upto-date for your State or Territory. Manufacturing Skills Australia and the original developer do not accept any liability for any damage or loss (including indirect and consequential loss) incurred by any person as a result of relying on the information contained in this material. Manufacturing Skills Australia, does not accept any liability to any person for the information or advice (or the use of such information or advice) which is provided in this material or incorporated into it by reference. The information is provided on the basis that all persons accessing this material undertake responsibility for assessing the relevance and accuracy of its content. No liability is accepted for any information or services which may appear in any other format. No responsibility is taken for any information or services which may appear on any linked websites. Published by: Manufacturing Skills Australia Release Date: June 2013 For further information about this resource or any other work being undertaken by Manufacturing Skills Australia (MSA), please visit: Manufacturing Skills Australia Level 3, 104 Mount Street North Sydney NSW 2060 T: F: E: info@mskills.org.au W: Manufacturing Skills Australia Page 2

3 Table of Contents Assessment... 6 Method of Assessment... 6 Assessment Mapping... Error! Bookmark not defined. Required Skills and Knowledge Mapping... Error! Bookmark not defined. Assessment Preparation Checklist... Error! Bookmark not defined. Assessment Method One - Short Answer Questions... Error! Bookmark not defined. Assessment Method One - Short Answer Questions... Error! Bookmark not defined. Result for Assessment... Error! Bookmark not defined. Assessment Method Two - Project... Error! Bookmark not defined. Assessment Method Two - Project... Error! Bookmark not defined. Result for Assessment... Error! Bookmark not defined. Observation Report... Error! Bookmark not defined. Assessment Method Three - Observation Report... Error! Bookmark not defined. Result for Assessment... Error! Bookmark not defined. Supervisor/Third Party Report... Error! Bookmark not defined. Manufacturing Skills Australia Page 3

4 Indirect Evidence... Error! Bookmark not defined. Assessment Outcome Record Sheet... Error! Bookmark not defined. Assessment Response Guide... Error! Bookmark not defined. Marking Schedule... Error! Bookmark not defined. Manufacturing Skills Australia Page 4

5 Overview This unit specifies the competence required to identify risks associated with welding operations and implementing hazard reduction practices. This unit addresses the competence that applies to gas and electric arc welding. It includes the identification of risks associated with welding all commonly used metals and implementation of techniques used to reduce or eliminate welding hazards. It is applicable in both a learning and assessment pathway and an assessment only pathway. This competence is performed in the context that all materials and equipment needed to carry out this function have been provided, including learning materials, learning programs and learning resources. Elements To achieve competency in this unit you must demonstrate your ability to: 1. Access and interpret OH&S information; 2. Identify risks associated with welding; and 3. Reduce risks associated with welding. Pre requisite units of competence Nil Manufacturing Skills Australia Page 5

6 Assessment In order to found competent in this unit you must competently complete all of the following Assessment tasks: Method of Assessment Assessment Method One Assessment Method Two Assessment Method Three Assessment Method Four Assessment Method Five Short Answer Questions Project Observation Report Third Party/Supervisor Report Indirect Evidence Note: There may be more assessment methods listed here than what is necessary to determine Competence. It is the individual RTO s decision to determine the methods that best suit their delivery arrangements and list them in their Training & Assessment Strategy in addition to removing those methods that are not required from this document. To the Assessor It is suggested that this assessment manual be de constructed from its current format and the respective assessment pages and instructions be provided to students at the pre-determined and/or suggested times. It should not be provided to the student in its current format. Manufacturing Skills Australia Page 6