VMiniature Basic Switch

Transcription

1 that Offers High Reliability and Security Wide variation of best-selling microswitches with switching currents of 10 to 21. Can be used for interrupting current when doors are opened or closed. vailable in two types of cases: thermoplastic resin and thermosetting resin. RoHS Compliant Model Number Legend : 21 at 250 C 16: 16 at 250 C 15: 15 at 250 C 10: 10 at 250 C 2. ctuator None : Pin plunger 1 : Short hinge lever 2 : Hinge lever 3 : Long hinge lever 4 : Simulated roller lever 5 : Short hinge roller lever 6 : Hinge roller lever 4. Terminals : C2 : C : 5. Maximum Force 6: 3.92 N {400 gf} 5: 1.96 N {200 gf} 4: 0.98 N {100 gf} Note: These values are for the pin plunger models. 6. Heat Resistance None : Standard (80 C) -T : Heat-resistive (150 C) 3. Contact Form 1: 2: SPST-NC 3: SPST-NO 1

2 List of Models Thermoplastic Case ctuator Terminals Contact form Maximum operating force (OF) Pin plunger SPST-NO SPST-NO SPST-NO C C26 SPST-NO C C C25 SPST-NO C25 SPST-NO -21-1C6-16-1C6-21-2C6-16-2C6 SPST-NO -21-3C6-16-3C C C5 SPST-NO C5 SPST-NO Refer to "Micro Switch Common ccessories" for Separators (sold separately), ctuators (sold separately) and Terminal Connectors (sold separately). 2

3 ctuator Terminals Contact form Maximum operating force (OF) Short hinge lever Hinge lever SPST-NO SPST-NO SPST-NO C C26 SPST-NO C C C25 SPST-NO C25 SPST-NO C C C C6 SPST-NO C C C C5 SPST-NO C5 SPST-NO SPST-NO SPST-NO SPST-NO C C26 SPST-NO C C C25 SPST-NO C25 SPST-NO C C C C6 SPST-NO C C C C5 SPST-NO C5 SPST-NO Refer to "Micro Switch Common ccessories" for Separators (sold separately), ctuators (sold separately) and Terminal Connectors (sold separately). 3

4 Long hinge lever Simulated roller lever SPST-NC 1.27N SPST-NO SPST-NC 0.69N SPST-NO SPST-NC 0.34N SPST-NO C26 SPST-NC 1.27N C26 SPST-NO C C25 SPST-NC 0.69N C25 SPST-NO C25 SPST-NC 0.34N SPST-NO C C6 SPST-NC 1.27N C C6 SPST-NO C C C5 SPST-NC 0.69N C5 SPST-NO C5 SPST-NC 0.34N SPST-NO SPST-NO SPST-NO SPST-NO C C26 SPST-NO C C C25 SPST-NO C25 SPST-NO C C C C6 SPST-NO C C C C5 SPST-NO C5 ctuator Terminals Contact form Maximum operating force (OF) SPST-NO Refer to "Micro Switch Common ccessories" for Separators (sold separately), ctuators (sold separately) and Terminal Connectors (sold separately). 4

5 Short hinge roller lever Hinge roller lever SPST-NC 4.71N SPST-NO SPST-NC 2.35N SPST-NO SPST-NC 1.18N SPST-NO C26 SPST-NC 4.71N C26 SPST-NO C C25 SPST-NC 2.35N C25 SPST-NO C25 SPST-NC 1.18N SPST-NO C C6 SPST-NC 4.71N C C6 SPST-NO C C C5 SPST-NC 2.35N C5 SPST-NO C5 SPST-NC 1.18N SPST-NO SPST-NO SPST-NO SPST-NO C C26 SPST-NO C C C25 SPST-NO C25 SPST-NO C C C C6 SPST-NO C C C C5 SPST-NO C5 ctuator Terminals Contact form Maximum operating force (OF) --- SPST-NO Refer to "Micro Switch Common ccessories" for Separators (sold separately), ctuators (sold separately) and Terminal Connectors (sold separately). 5

6 Thermosetting case Heat-resistive ctuator Terminals Contact form Maximum operating force (OF) Pin plunger Short hinge lever T SPST-NO T T SPST-NO T T SPST-NO T -15-1C C26-T C SPST-NO -15-3C C C C25-T -10-1C25-T -15-2C C25 SPST-NO -15-3C C C C24-T C24 SPST-NO C C C6-T C6 --- SPST-NO -15-3C C5-10-1C5-15-1C5-T -10-1C5-T -15-2C5-10-2C5 SPST-NO -15-3C5-10-3C C C4-T C4 SPST-NO C T SPST-NO T T SPST-NO T SPST-NO C C26-T C SPST-NO C C C C25-T C25-T C C25 SPST-NO C C C C24-T C24 SPST-NO C C C6-T C6 --- SPST-NO C C C C5-T C5-T C C5 SPST-NO C C C C4-T C4 SPST-NO C4 Refer to "Micro Switch Common ccessories" for Separators (sold separately), ctuators (sold separately) and Terminal Connectors (sold separately). 6

7 Heat-resistive ctuator Terminals Contact form Maximum operating force (OF) Hinge lever Long hinge lever T SPST-NO T T SPST-NO T SPST-NO C C26-T C SPST-NO C C C C25-T C25-T C C25 SPST-NO C C C C24-T C24 SPST-NO C C C6-T C6 --- SPST-NO C C C C5-T C5-T C C5 SPST-NO C C C C4-T C4 SPST-NO C T --- SPST-NC 1.27N SPST-NO T T SPST-NC 0.69N SPST-NO T SPST-NC 0.34N SPST-NO C C26-T --- SPST-NC 1.27N C SPST-NO C C C C25-T C25-T SPST-NC 0.69N C C25 SPST-NO C C C C24-T SPST-NC 0.34N C24 SPST-NO C C C6-T --- SPST-NC 1.27N C6 --- SPST-NO C C C C5-T C5-T SPST-NC 0.69N C C5 SPST-NO C C C C4-T SPST-NC 0.34N C4 SPST-NO C4 Refer to "Micro Switch Common ccessories" for Separators (sold separately), ctuators (sold separately) and Terminal Connectors (sold separately). 7

8 Heat-resistive ctuator Terminals Contact form Maximum operating force (OF) Simulated roller lever Short hinge roller lever T SPST-NO T T SPST-NO T SPST-NO C C26-T C SPST-NO C C C C25-T C25-T C C25 SPST-NO C C C C24-T C24 SPST-NO C C C6-T C6 --- SPST-NO C C C C5-T C5-T C C5 SPST-NO C C C C4-T C4 SPST-NO C T --- SPST-NC 4.71N SPST-NO T T SPST-NC 2.35N SPST-NO T SPST-NC 1.18N SPST-NO C C26-T --- SPST-NC 4.71N C SPST-NO C C C C25-T C25-T SPST-NC 2.35N C C25 SPST-NO C C C C24-T SPST-NC 1.18N C24 SPST-NO C C C6-T --- SPST-NC 4.71N C6 --- SPST-NO C C C C5-T C5-T SPST-NC 2.35N C C5 SPST-NO C C C C4-T SPST-NC 1.18N C4 SPST-NO C4 Refer to "Micro Switch Common ccessories" for Separators (sold separately), ctuators (sold separately) and Terminal Connectors (sold separately). 8

9 Heat-resistive ctuator Terminals Contact form Maximum operating force (OF) Hinge roller lever T SPST-NO T T SPST-NO T SPST-NO C C26-T C SPST-NO C C C C25-T C25-T C C25 SPST-NO C C C C24-T C24 SPST-NO C C C6-T C6 --- SPST-NO C C C C5-T C5-T C C5 SPST-NO C C C C4-T C4 SPST-NO C4 Contact form SPST-NC SPST-NO NC NO NC COM COM Refer to "Micro Switch Common ccessories" for Separators (sold separately), ctuators (sold separately) and Terminal Connectors (sold separately). 9

10 Contact Specifications Item Model Specification Rivet Contact Material Silver alloy Silver Gap (standard value) 1 mm Inrush NC current NO max. max. max. max. Minimum applicable load (reference value) DC5 160m Model Rated voltage C250 DC125 DC250 C250 DC125 DC250 C250 DC125 DC250 C250 DC125 DC250 Item Resistive load Note. The above rating values apply under the following test conditions. (1) mbient temperature: 20±2 C (2) mbient humidity: 65±5% RH (3) frequency: 30 operations/min pproved Standards UL (UL1054)/CS (CS C22.2 No.55) Rated voltage Model C 250 C 21 1/2HP 16 1/2HP 15 1/2HP 10 1/2HP 125 DC 250 DC DE (EN ) Consult your OMRON sales representative for specific models with DE approvals. Rated voltage Model C250 20(4) 16(4) Testing conditions: 5E4 (50,000 operations), for models of -21: T80 (0 to 80 C), for models of -16: T105 (0 to 105 C) Characteristics Item Model Permissible operating speed 0.1mm to 1 m/s max. (pin plunger models) Permissible operating Mechanical 600 operations/min max. (pin plunger models) frequency Electrical 60 operations/min Insulation resistance 100MΩ min. (at 500 DC with insulation tester) Contact resistance (initial value) 15mΩ max. Between terminals of the same polarity C1,000 50/60Hz 1min Between current-carrying Dielectric strength *1 metal parts and ground C1,500 50/60Hz 1min C1,500 50/60Hz 1min C2,000 50/60Hz 1min Between each terminals and non-current-carrying metal parts C1,500 50/60Hz 1min C1,500 50/60Hz 1min C2,000 50/60Hz 1min ibration resistance *2 Malfunction 10 to 55 Hz, 1.5-mm double amplitude Durability 1,000 m/s 2 {approx. 100 G} max. Shock resistance *2 200 m/s Malfunction {approx. 20G} max. 300 m/s 2 {approx. 30 G} max. Mechanical 50,000,000 operations min. (60 operations/min) Durability *3 Electrical 300,000 operations min. (30 operations/min) Heat resistive: 50,000 operations min (30 operations/min) 100,000 operations min. (30 operations/min) Heat resistive: 20,000 operations min (30 operations/min) 100,000 operations min. (30 operations/min) Degree of protection IEC IP40 Degree of protection against electric shock Class I Proof tracking index (I) to 105 C mbient operating temperature (Heat resistive: -25 to 150 C) -25 to 105 C -25 to 80 C (at ambient humidity of 60% max.) (with no icing or condensation) mbient operating humidity 85% max. (for 5 to 35 C) Weight pprox. 6.2g (pin plunger models) Note. The data given above are initial values. *1. The dielectric strength shown in the table indicates a value for models with a Separator. *2. For the pin plunger models, the above values apply for use at the free position and total travel position. For the lever models, they apply at the total travel position. Close or open circuit of the contact is shorter than 1 ms. *3. For testing conditions, consult your OMRON sales representative. 10

11 Terminals and pperance (Unit: mm) (5.5) (6.5) 2.9 t=0.5 (10) Three, solder terminals (5.5) (6.5) 2.9 t=0.5 (10) Three, quick-connect (4.9) (7.7) 3.2 t=0.8 (12.0) Three, quick-connect * ± dia. 1.6 dia. * Indicates the length to the center of the 1.6-dia. holes 4.75± dia. terminal hole 6.35± dia. terminal hole Note. The above is for the contact specifications. Two terminals will be available for SPST-NO or SPST-NC contact specifications. For terminal positions, refer to Contact form on page 9. Mounting Holes (Unit: mm) Two, 3.1-dia. mounting holes or M3 screw holes ±0.1 11

12 Dimensions and Characteristics Thermoplastic Case -21/-16 Models The following illustrations and drawings are for quick-connect terminals #250 (terminals C). models with a switching current of 16 and 11 incorporate solder terminals and quick-connect termimals #187. These models are different from #250 models in terminal size only. Dimensions of solder terminals and quickconnect terminal #187 are omitted. Please refer to the "Terminals and Shapes" on previous page. is replaced with the code for the terminals. See the "List of Models" for available combinations of shapes. Pin plunger -21-1@6-16-1@6-16-1@5 20.2±0.25 ± ± (12.0) φ hole 19.1 Three, quick-connect (t0.8) 4.2 Model -21-1@6-16-1@6 3.92N 0.78N 1.2mm 1.0mm 0.4mm 14.7±0.4mm -16-1@5 1.96N Short hinge lever @ @ @5 ± ± (12.0) φ hole Three, quick-connect (t0.8) * Stainless-steel lever Model @ @6 3.92N 0.8mm 0.6mm 15.2±0.5mm @5 1.96N Hinge lever @ @ @5 ± ± ± (12.0) φ hole Three, quick-connect (t0.8) * Stainless-steel lever Model @ @6 2.45N 0.25N 4.0mm 1.5mm 15.2±1.2mm @5 1.23N 0.14N Long Hinge Lever Models @ @ @5 59.4± ± (12.0) φ hole ± Three, quick-connect (t0.8) * Stainless-steel lever 4.3 Model @ @6 1.27N 0.12N 9.0mm 2.0mm mm mm @5 0.69N 0.06N Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note 2. The operating are for operation in the direction ( ). 12

13 Simulated roller lever R3.5 ± ± ± (12.0) φ hole Three, quick-connect (t0.8) * Stainless-steel lever Model @ @6 2.45N 0.25N 4.0mm 1.5mm 18.7±1.2mm @5 1.23N 0.14N Short hinge roller lever @ @ @5 ± ± (12.0) φ hole 19.1 Three, quick-connect (t0.8) *1. Stainless-steel lever *2. Polyacetal resin roller 5.1 φ *2 Model @ @6 4.71N 0.8mm 0.6mm 20.7±0.6mm @5 2.35N Hinge roller lever @ @ @5 34± φ hole 5.1 φ *2 ± ±0.8 (12.0) 19.1 Three, quick-connect (t0.8) *1. Stainless-steel lever *2. Polyacetal resin roller Model @ @6 2.45N 0.25N 4.0mm 1.5mm 20.7±1.2mm @5 1.23N 0.14N Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note 2. The operating are for operation in the direction ( ). 13

14 Thermosetting Case (-15/-10 Models) The following dimensions and Characteristics are for both "Not specified: Standard (105 C)" and "-T: Heat-resistive (150 C)" models. The following illustrations and drawings are for solder terminals (Terminal ). models with a switching current of 15 and 10 have quick-connect terminals #187. These models are different from solder terminal models in terminal size only. Illustrations for quick-connect terminals #187 are omitted. Please refer to "Terminals and Shapes" on page 8. is replaced with the code for the terminals.see the "List of Models" for available combinations of shapes. pplicable to both Standard (105 C) and Heat-resistive (150 C) models Pin plunger -15-1@6-15-1@5-10-1@5-10-1@4 20.2±0.25 ± ±0.8 φ hole (10) t=0.5 Three, solder terminals Model -15-1@6-15-1@5-10-1@5-10-1@4 3.92N 078N 1.96N 1.2mm 1.0mm 0.4mm 14.7±0.4mm 0.98N 0.20N Short hinge lever @ @ @ @4 ± ±0.8 φ hole (10) t=0.5 Three, solder terminals * Stainless-steel lever Model @ @ @ @4 3.92N 1.96N 0.8mm 0.6mm 15.2±0.5mm 0.98N 0.15N Hinge lever @ @ @ @4 35.6±0.8 ± ± ±0.8 φ hole (10) 4.3 t=0.5 Three, solder terminals * Stainless-steel lever Model @ @ @ @4 2.45N 0.25N 1.23N 0.14N 4.0mm 1.5mm 15.2±1.2mm 0.59N 0.06N Long Hinge Lever Models @ @ @ @4 ± ± ±0.8 φ hole (10) t=0.5 Three, solder terminals * Stainless-steel lever Model @ @ @ @4 1.27N 0.12N 9.0mm 2.0mm mm 0.69N 0.06N mm 0.34N - 9.0mm 3.2mm mm 15.2±2.6 mm Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note 2. The operating are for operation in the direction ( ). 14

15 Simulated roller lever R3.5 ± ± ±0.8 φ hole (10) t=0.5 Three, solder terminals * Stainless-steel lever Model @ @ @ @4 2.45N 0.25N 1.23N 0.14N 4.0mm 1.5mm 18.7±1.2mm 0.59N 0.06N Short hinge roller lever @ @ @ @ ± ± ±0.8 φ hole φ *2 5.1 t=0.5 Three, solder terminals *1. Stainless-steel lever *2. Polyacetal resin roller Stainless steel roller for heat-resistive models Model @ @ @ @4 4.71N 2.35N 0.8mm 0.6mm 20.7±0.6mm 1.18N 0.15N Hinge roller lever @ @ @ @4 ± ± ±0.8 φ hole (10) φ *2 5.1 t=0.5 Three, solder terminals *1. Stainless-steel lever *2. Polyacetal resin roller Stainless steel roller for heat-resistive models Model @ @ @ @4 2.45N 0.25N 1.23N 0.14N 4.0mm 1.5mm 20.7±1.2mm 0.59N 0.06N Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note 2. The operating are for operation in the direction ( ). Precautions Please read "Common Precautions" for correct use. Soldering Precautions for Safe Use Connecting to Solder Terminals Complete the soldering at the iron tip temperature of 250 to 350 C (60W) within 5 seconds, and do not apply any external force for 1 minute after soldering. Be sure to apply only the minimum required amount of flux.it may result in contact failure once the flux penetrates into the internal part of the Switch. Connecting to Terminals #187 Insert the receptacle of quick-connect terminal #187 straight toward the terminal. pplying excessive external force horizontally or vertically may cause deformation of terminals and may damage the housings. Connecting to Terminals #250 Insert the receptacle of quick-connect terminal #250 straight toward the terminal. pplying excessive external force horizontally or vertically may cause deformation of terminals and may damage the housings. Precautions for Correct Use Mounting Use M3 mounting screw with plane washers or spring washers to securely mount the Switch.Tighten the screws to a torque of 0.39 to 0.59N m {4 to 6 kgf cm}. 15

16 pplication examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product. Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the ratings and performance of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms. Note: Do not use this document to operate the Unit. OMRON Corporation Electronic and Mechanical Components Company Contact: Cat. No. B010-E (0207)(O) 16