Suzanna Nagy International Approvals TUV Rheinland

Transcription

1 Suzanna Nagy International Approvals TUV Rheinland

2 What is The Customs Union On October 6, 2007 The Republic of Kazakhstan, Republic of Belarus and Russian Federation agreed to form a customs union. The goal of the union is to create a unified customs territory without customs taxes and other economic or regulatory restrictions A list of products that will subject to mandatory conformity assessment was adopted on 07/18/2010 On February 15, 2013 a number of Customs Union Technical Regulations were enforced (EMC, LVE, Machinery, Ex, Gas) Transitional period will end on March 15, 2015

3 Custom Union Benefits Common regulatory approval related documents are accepted throughout the customs union Additional benefits Reduced testing Reduced cost Reduced certification time

4 Products not included in the unified list Remain subject to the national approval process For example, medical equipment is not included in the unified list of products subject of mandatory conformity assessment in the framework of the Customs Union It's possible that Unified list will be extended according with National certification schemes Two methods to determine if product is subject to Customs Union certification scheme: By Product category from unified list By HS code

5 Low Voltage Equipment Technical Regulation Essential requirements: Low voltage equipment should be developed and manufactured to provide safety regarding: electrical shock, arcs or emissions, high temperatures, moving parts, noise, dangerous chemicals, insulation, stability to environmental influences, risks during connection and installation, risks during accidents (article 4) In-scope equipment: AC electrical equipment V DC electrical equipment V Out-of-scope equipment: Medical equipment Military equipment Ex-proof equipment elevator and lift components Vehicle parts Equipment for nuclear power plants

6 EMC Technical Regulation Essential requirements: Any equipment should be designed and manufactured for compliance with following general requirements - EM disturbances created by the equipment should not exceed the level provided by the operation of RF and other products according to their appointment; equipment should possess stability to EM disturbances (immunity) In-scope equipment: applicable to any equipment which is able to create EM disturbances and if operation quality depends on external EM influence Out-of-scope equipment: Components Passive items Cables, cords, plugs, sockets Batteries High voltage equipment Induction motors etc.

7 Machinery Technical Regulation In-scope equipment: Light industry equipment Food industry equipment Industrial fans and air conditioners Pumping equipment Mine equipment Autoloaders, tractor trailers Excavation equipment etc. Out-of-scope equipment: Telecom equipment Medical products Equipment for nuclear power industry Automotive, marine, railway, aerospace equipment Military equipment etc.

8 Marking and Language Requirements (LVE, EMC, Gas, Machinery) On the product: (English is acceptable) product name, brand name, EAC mark, manufacturer s name, rating label, country of origin date of manufacture (mm/yyyy)* rated heat output**, type and required gas pressure**, safety warnings** On the package: (English is acceptable) product name, brand name, EAC mark, manufacturer s name In the user manual: (Russian; Kazakh and Belarus is required for these countries respectively) product name, brand name, EAC mark, rating label, country of origin manufacturer s/local rep s name and address installation guidelines rules for safe use actions in case a device failure is detected information about safe storage, handling, use, servicing and recycling manufacturer s/local rep s address and phone number* date of manufacture (mm/yyyy)* EAC mark has to be min. 5 mm, monochrome (one-color) and contrasting with the surface color * Only for machinery or gas equipment TR ** Only for gas equipment TR

9 Marking and Language Requirements (Ex) On the product: (English is acceptable) product name, brand name, EAC mark, product type, manufacturer s name CoC number, exact Ex-mark, factory number On the package: (English is acceptable) product name, brand name, EAC mark, manufacturer s name In the user manual: (Russian; Kazakh and Belarus is required for these countries respectively) product name, brand name, EAC mark, rating label, country of origin manufacturer s/local rep s name and address installation guidelines rules for safe use actions in case a device failure is detected information about safe storage, handling, use, servicing and recycling manufacturer s/local rep s address and phone number date of manufacture (mm/yyyy) information about CoC EAC mark has to be min. 5mm, monochrome (one-color) and contrasting with the surface color Letter x / Letter E = 5 / 9; h / w = 11 / 8; h = min. 10mm

10 Certificate of Conformity Workflow PREPARATION: check HS code, procedure type and applicable standards check local representative availability, user manual translations and FI report request quote APPLiCATION: prepare a complete application package with the following: signed application form (signed by local rep), Power of Attorney, translated user manual (min. Russian), schematics, photos, test reports and certificates, ISO 9001 certificate for factory/cig023 FI report Submit application CERTIFICATION: check CoC draft for correct HS code, correct model name and correct manufacturer/factory receive CoC apply EAC mark to product

11 Declaration of Conformity Workflow PREPARATION: check HS code, procedure type and applicable standards check local representative availability, user manual translations and FI report request quote APPLiCATION: prepare a complete application package with the following: signed application form (signed by local rep), Power of Attorney, translated user manual (min. Russian), schematics, photos, test reports and certificates, ISO 9001 certificate for factory/cig023 FI report Submit application CERTIFICATION: check CoC draft for correct HS code, correct model name and correct manufacturer/factory receive CoC apply EAC mark to product

12 Hygienic Approval Responsible Interstate Body: Customs Union Commission Responsible State (Russian) Body Federal Service on Protection of the Consumers Rights (ROSPOTREBNADZOR) Mandatory lists are regulated in Decision of Customs Union commission #299 28/05/2010 Agreement of Custom Union About Sanitary rules of Custom Union December 11, 2009 Decision of Customs Union Commission #319 at 18/06/2010 with amendments (General rules) Decision of Customs Union Commission #299 at 28/05/2010 (Mandatory lists of products) Federal law of Russia On Technical Regulation #184-ФЗ 27/12/2002 (add ) Federal law of Russia On sanitary-and-epidemiologic well-being of the population #52-ФЗ 30/03/1999 Federal law of Russia On protection of the rights of the consumers #127-ФЗ 02/11/2004

13 Hygienic Approval Workflow PREPARATION: check HS code, product type and hygienic procedure type request quote APPLiCATION: prepare a complete application package with the following: signed application form, Power of Attorney, user manual (English acceptable), product labels (if applicable), ISO 9001 certificate for factory/cig023 FI report, test samples (if applicable) Submit application CERTIFICATION: check state registration certification/expert conclusion draft for correct model name and correct manufacturer/factory receive state registration certification/expert conclusion with test report

14 FSS (encryption) Notification Responsible State Body: Center for Licensing, Certification and Protection of State Secrets FSS On unified export/import regulation of the Customs Union (Belarus, Kazakhstan and Russia) issued by The EuroAsian economic community interstate council (the supreme body of the customs union) the Decision from November, 27th, Minsk. (2.19) In-scope equipment: 1. Products which use crypto algorithms: symmetric (key length <= 56bits) dissymmetric (key length <= 512bits) 2. Products with limited crypto features: authentication and access management electronic authorization systems (digital signature) 3. Crypto components (software) of operating systems, which can t be modified by users 4. Personal smartcards 5. Radio/TV broadcast receivers (without crypto features) 6. Equipment with crypto features, which is not available to users 7. Equipment with crypto features, especially developed for banks and other financial operation 8. Portable wireless devices intended for cellular communication and LAN (400m max) 9. Equipment for protection telecommunication systems

15 FSS Notification Workflow PREPARATION: check product type and encryption algorithms used check local representative availability request quote APPLiCATION: prepare a complete application package with the following: signed application form, Power of Attorney (apostille i.e. notarized and legalized in country of manufacturer s origin), user manual (English acceptable) Submit application CERTIFICATION: check notification draft for correct model name receive registered notification

16 Telecom Approvals in CU Responsible State Body: Federal Telecom Agency In-scope equipment: If the equipment is installed or connected to Common Telecom Network by any way i.e. by cable, optic or radio channel GSM, WCDMA, HSDPA, CDMA terminal equipment / base stations analog PSTN terminal equipment power supply systems data cables optical media converters VoIP products FM transceivers 3G/UMTS products WAN/LAN switching/routing equipment wireless equipment (Bluetooth/WiFi/WiMAX/LTE)

17 Telecom Approval in CU In accordance with Order of RF Government #532 25/06/2009 if Telecom products listed below are used: in the public communication network in technology networks (LAN) appended to a public communication network in networks of special-purpose (government) appended to a public communication network then subject to mandatory certification procedure. I. Base Switching systems II. Base digital transport systems III. Management and monitoring systems IV. Billing systems (soft & hard) V. Base RF systems VI. Legal interception systems (soft & hard) If Telecom products are not listed for mandatory certification procedure then they are subject to mandatory declaration procedure.

18 Telecom Approval Workflow PREPARATION: check product type and telecom procedure type check local representative availability check applicable standards request quote APPLiCATION: prepare a complete application package with the following: application (CoC), Power of Attorney (CoC), agreement with manufacturer (DoC), user manual (English acceptable), EN/ETSI/TBR report, ISO 9001 certificate, test sample (if applicable) Submit application CERTIFICATION: check CoC / DoC draft for correct model name and correct manufacturer/factory receive Telecom CoC / DoC

19 Nearly 140 Years of Innovation 1872 Entrepreneurs take the initiative and set up the DÜV to ensure the safety of their manufacturing plants 1918 Activities in the energy and mining sectors 1957 Commitment to environmental protection: dust register in Cologne 2006 Joined the UN Global Compact 2009 World s largest photovoltaic lab 1926 First material analysis laboratory 1900 Vehicle inspection and driving license tests 1975 Medical work 1969 International product tests and certifications 2007 Represented on all continents

20 500 locations in 65 countries around the world Always at your service: 220 offices in Germany.

21 Upcoming International Approvals Events Upcoming Roundtables (4-6 hour events) September 10 Orlando, FL Register at Passport Seminars (4-6 hour events) September 17 - IA Briefing for China/Taiwan (Boxborough MA) September 19 - IA Briefing for China/Taiwan (Pleastanton CA) Register at Passport Webinars (45 minute events) August 6 - IA Briefing for Russia/Customs Union (2:00pm ET) September 12 IA Briefing for Brazil (2:00pm ET) November 12 IA Briefing for Australia/New Zealand (2:00pm ET) Register at:

22 Next Steps Contact us for more information or to start a project. Or call us at

23 Questions?