4CH 2.4G REMOTE CONTROL QUADCOPTER INSTRUCTION MANUAL IMPLEMENT STANDARD: GB/T

Transcription

1 AGES 14+ X 5C 4CH 2.4G REMOTE CONTROL QUADCOPTER 1 INSTRUCTION MANUAL IMPLEMENT STANDARD: GB/T Key features of quadcopter Four-axis struture makes the quadcopter more flexible and rapid when flying. It is wind-resistant and can be flown indoor or outdoor. Built-in 6 axis gyroscope for precise hovering in the sky. Simple modular design makes changing parts easy. With 360º 3D eversion and throwing flight function. The materials and specification mentioned in this instruction manual or the parts inside this package are for reference only.any updated or changed please refer to our website:

2 PREFACE Dear Customers: Thank you for purchasing our flying model.please read this instruction manual carefully in order to master the skill more quickly and operate this product more safely.in the mean time,please well keep the original of this instruction manual for future reference. CONTENTS Ｑｕａｄｃｏｐｔｅｒ Ｔｒａｎｓｍｉｔｔｅｒ Ｍａｉｎ ｂｌａｄｅｓ Ｓｃｒｅｗ ４ＰＣＳ ＵＳＢ Ｃｈａｒｇｉｎｇ Ｃａｂｌｅ Ｓｃｒｅｗｄｒｉｖｅｒ Ｉｎｓｔｒｕｃｔｉｏｎ ｍａｎｕａｌ -1-

3 GET TO KNOW YOUR TRANSMITTER Introduction of transmitter Antenna Indicator High/Low speed switch 3D Eversion/photo and video (this function for item no. X5C) Left control lever (Accelerator) Right control lever Forward and backward trimmer Mode switch Sideward Fine-tuning (Mode 1) Left Fine -tuning(mode 2) Hover up and down trimmer Left Fine -tuning(mode 1) Sideward Fine-tuning (Mode 2) Power ON/OFF LCD Displayer Remote control Installing the battery Battery Cover 4 X AA(LR06) 1.5V Batteries Figure 1 Figure 2 1.Use a screwdriver to remove the screw on the back of transmitter,than open the battery cover(figure 1). 2.Install 4 AA batteries (not included) into the back of transmitter than replace battery cover and reinstall the screw (Figure 2). 1.Install batteries with correct polarity. 2.Do not mix old and new batteries. 3.Do not mix different types of batteries. REMOTE CONTROL KEYPAD AND LCD MANUAL A B -2-

4 01.Sideward Fine-tuning :Power-on start in the centering.(be turn Left/Right Fine -tuning in Mode2) 02.Forward/Backward fine-tuning:power-on start in the middle. 03.Turn Left/Right fine-tuning:power-on start in centering.(be Sidewoard Fly Fine -tuning in Mode2) 04.Throttle lever fine-tuning Power-on start in middle. 05.Throttle show:power-on start in lowest level.(left and Right throttle shows at one time) 06.Forward shows:power-on start in the lowest level.(at the center spuare) 07.Backward shows:power-on start in the lowest level.(at the center spuare) 08.Right sideward fly shows:power-on start in the lowest level.(at the center spuare) 09.Left sideward fly shows:power-on start in the lowest level.(at the center spuare) 10.Turn left: Pull left function lever to left, it will be higher, than quad copter turn left faster. 11.Turn right: Pull left function lever to right, it will be higher, than quad copter turn right faster. 12.High/Low speed: Press button A for seconds to switch between high speed mode or low speed mode. H means high speed and L means low speed. 13.Power shows:according to the battery's energy for the controller. 14.Default mode when power-on.when change to MODE 2, please keep pressing button "B" to right than return on the power of transmitter, the MODE on LCD displayer will be changed. Same steps to change to MODE 1 again. 15.Signal shows:normally to full frame. READY TO FLY YOUR QUADCOPTER Step 1: Press the ON/OFF Step2: Open the battery Step 3: Close the battery power switch up. cover and insert the cover and turn on battery into power the quadcopter. port. Step 4:Push the throttle lever to the highest position, and then pull it back to the lowest position. There will be one clear sound from the transmitter, this shows that the quadcopter has entered into the pre-fly state. Horizontal position TIPS:When syncing your quadcopter keep it in a horizontal position to start to a stable flight. -3-

5 CAUTIONS: 1.When the indicator of transmitter keep light on but the indicator of quadcopter is blinking slowly, it means signal matching was not successful. Please turn off the power both of transmitter and quadcopter than restart the transmitter and quadcopter. 2.If the quadcopter is till flying to on side dramatically or spinning while hovering, please switch off the power of both the quadcopter and transmitter and then repeat the pre-flying steps. 3.When the indicator of the quadcopter keeps flashing slowly, it means that the quadcopter has entered into the low battery state. This time you need to charge the quadcopter with the USB cable provided. CHANGE BATTERY OF QUADCOPTER 缺产品 Push the on/off switch of quadcopter to OFF position than open the battery cover. 2.Pull out the battery wire from the power port Take out the USB charging cable, and insert the battery power port to the small end of it (Make sure the ports connect tight and correct ). 4.To charge battery, please insert the USB port of provided USB charging cable to anyone USB port of computer. The indicator on USB cable will light ON during charging battery, than it will light OFF when battery fully charged. Caution: When using the computer for charging, please remember to pull out the charging cable before shutting down the computer.take the battery cover, and close the battery cover on the quadcopter. 5 5.Reconnect the battery wire to power port than close the battery cover. Charging time: about 75 minutes Flying time: about 7 minutes! -4-

6 CAUTIONS WHEN CHARGING 1.When charging, please put this product on a dried or ventilated area and keep it far away from heat source or explosive product. 2.When charging, please remove the batteries from the quadcopter. Then charging process should be supervised by an adult so as not to cause an accident. 3.After flying, please do not charge the battery if the surface temperature is still not cool. Otherwise it may cause a swollen battery or even a fire hazard. 4.Please make sure that you use the original USB charging cable provided.when the battery has been used for a long time, or appears to be swollen, please replace them. 5.A battery when not in use for a long time will lose its charge automatically. Charging or discharging too often may reduce the life of the battery. BATTERY REPAIR & MAINTENANCE 1.Battery should be put in the dried or ventilated place with enviroment temperature about In order to enhance the using life of the battery, please avoid repeat charging or excessive discharging. 3.When the battery needs to be stored for a long time,please charge the battery first.that is to say, charge the battery for about 50-60% of the volume and then well store it. 4.If you do not use it for more than 1 months, it s highly recommended that you need to check the battery voltage every month so as to make sure the voltage no less than 3V. Otherwise please do by following No.(3) mentioned. INSTALL LANDING SKIDS & BLDAE PROTECTING FRAME Figure.1 Figure.2 1.Install the landing skids to the bottom of quadcopter (Figure 1). 2.Install the blade protecting frame to every corner than lock screws (Figure 2). CONTROLLER MODES & INSTRUCTIONS The transmitter built-in two modes, Mode 1 & Mode 2, in line with different customer s usage pattern. Keep pushing button B to right, than turn on the transmitter power to change Mode 1 or Mode B

7 MODE 1 Operating direction Hover up and down Forward and backward Push the throttle up or down, the quadcopter flies upward or downward. Push the direction lever up or down, the quadcopter flies forward or backward. Turn Left and Right Sideward fly Pull the throttle left or right, the quadcopter turns to left or right. Pull the direction lever left or right, the quadcopter flies to left side or right side. Fine-tuning operation Forward/Backward fine-tuning Sideward fly fine-tuning Turn left/right fine-tuning When the quadcopter keeps flying forward / backward, you can correct it by pressing fine-tuning button down / up. When the quadcopter keeps flying to left / right side, you can correct it by pressing the Fine-tuning button right / left. When the quadcopter keeps rotating to left /right, you can Correct it by pressing the fine-tuning button right / left. -6-

8 MODE 2 Operating direction Hover up and down Forward and backward Push the throttle up or down, the quadcopter flies upward or downward. Push the direction lever up or down, the quadcopter flies forward or backward. Sideward fly Turn Left and Right Pull the direction lever left or right, the quadcopter turns to left or right. Pull the throttle left or right, the quadcopter flies to left side or right side. Fine-tuning operation Forward/Backward fine-tuning Sideward fly fine-tuning When the quadcopter keeps flying forward / backward, you can correct it by pressing fine-tuning button down / up. When the quadcopter keeps flying to left / right side, you can correct it by pressing the fine-tuning button right / left. -7- Turn left/vright fine-tuning When the quadcopter keeps rotating to left /right, you can Correct it by pressing the fine-tuning button right / left.

9 INTRODUCTION TO QUADCOPTER FUNCTIONS Low-voltage protection: When the quadcopter battery is not enough the rotors will be stopped power supply.as the quadcopter control systemwill protected battery automatically. Over-current protection: When the quadcopter s rotating blade is collided or jammed, the control system will stop supplying power for the rotors automatically, Then please re-match the signal for flying. Restart function: In case of flight disorder or sideward flight, restore factory default settings by the following methods: ①.Press the power switch to turn on the transmitter. ②.Press the power switch to turn on the quadcopter. ③.When the quadcopter indicator quickly flashing to slowly flashing,please push the throttle lever to the highest position,and then pull it back to the lowest position.then the quadcopter indicator changed from slowly flashing to normal lights up. ④.Place the quadcopter on a horizontal postion, then push transmitter both left and right lever to lowest right conner for about 2-3 second, indicator on the quadcopter changed from normal lights up to quickly flashing ;After 2-3 second,the indicator changed to normal lights,it means the quadcopter restarted /reset successfully. 3D EVERSION AND THROWING FLIGHT INSTRUCTIONS When you are familiar with the basic operation, you can do some awesome & exciting tricks and stunts! First of all, fly the aircraft to a height of more than 3 meters, press the 3D Eversion switch on the rear right side of the transmitter, then push the right rudder(in any direction) to make 360 degree flip. Tips:3D eversion goes better when battery power is enough. -8-3m

10

11

12