The check-in conveyor is the interface between the passenger and the baggage handling system. It is designed to ensure easy loading capacity.

Transcription

1 Check-in Introduction The check-in conveyor is the interface between the passenger and the baggage handling system. It is designed to ensure easy loading capacity. It can be supplied as a one, two, three or four stage conveyor configuration. Function The check-in conveyor is designed to weigh baggage and dispatch it onto the collector conveyor without the need for manual lifting. Whilst there are standard configurations available, it is sufficiently flexible to accommodate variations in height,.

2 Daifuku ATec s range of weigh, label, tub load and dispatch conveyors can be configured into one, two, three or four stage check-in arrangements, i.e. One stage Two stage Three stage Four stage Bags are weighed, labelled and then dispatched onto the collector conveyor using a single weigh conveyor. The weighing and labelling operations are carried out on a single conveyor and bags are then dispatched via the induct conveyor onto the collector conveyor. Separate conveyors are used for weighing, labelling and then dispatch of the bags onto the collector conveyor. Separate conveyors used for weighing, labelling, tub loading and then dispatch of the bags onto the collector conveyor. Features Ergonomic design. The tub load feature is available in two, three and four stage design reducing the amount of lifting the check-in personnel have to perform. Lift off side panels allow for easy maintenance. Roll out system allows for easy access for cleaning hence reducing fire risk. High quality stainless steel finish. Designed to eliminate trap points for fingers, straps and labels. Technical Data The check-in conveyors are finished in high quality stainless steel. As a standard they are designed to eliminate trap points for passengers, operators, bag straps and labels. Safety gates may be fitted to the weigh conveyors as a security measure, preventing passengers from entering the check-in areas when the desks are closed.

3 Mechanical Specifications General Dimensions Overall Length & Width Standard Lengths Available Weigh of the weigh 1200 mm 1500 mm 2000 mm (single stage) Label of the label Tub Load of the tub load conveyor is may (induct) of the dispatch 1200 mm 1200 mm 1200 mm Belt Width 588 mm 588 mm 588 mm 588 mm Belt Speed 0.5 m/sec 0.5 m/sec 0.5 m/sec 0.5 m/sec Height (to top of panelling) Height (to top of belt front) Height (to top of belt rear) 475 mm 475 mm 475 mm 475 mm Drive Roller Width 562 mm RL 562 mm RL 562 mm RL 562 mm RL Between Side Panel Width 596 mm 596 mm 596 mm 596 mm Weighing Capacity 150 kgs N/A N/A N/A Live Load/Unit 60 kgs / unit 60 kgs / unit 60 kgs / unit 60 kgs / unit Static Capacity 120 kgs 120 kgs 120 kgs 120 kgs General Specifications Head/Tail Roller Side Panels Details Material Thickness Finish This roller is 60 mm diameter and fitted with 20 mm diameter bright mild steel shafts mounted on sealed precision bearings. The stainless steel cover panels provide an aesthetically pleasing trim that covers the workings of the conveyor and the control photo eyes etc. All Mild steel 304 stainless steel 3.2 mm wall thickness Natural 2 mm No 4 brush

4 Front Bump Rail Deck Pan/Chassis Plinth Bracketry stainless steel panelling is turret punched or laser cut and machine folded for accuracy and interchange ability. The front panel can be unlatched enabling the conveyors to be rolled out for cleaning and maintenance. The conveyor chassis is a punched and pressed folded steel fabrication to which all trim and roller bracketry is mounted. The floor plinth is a heavy duty mild steel fabrication, which supports, aligns and locks the weigh, label and dispatch conveyors. It also houses the motor control panels in most cases. The plinth is bolted securely to the floor using masonry anchors. (5 mm rails and 5 mm cross bracing). All trim and photo eye bracketry is punched and machine folded for accuracy. 304 stainless steel 2 mm No 4 brush Mild steel 3 mm Powder coated black Mild steel 5 mm Powder coated black Mild steel 1 mm Drive Specifications Weigh Label Tub Load (Induct) Manufacturer Interoll Interoll Interoll Interoll Type Power 0.33 kw 0.33 kw 0.33 kw 0.33 kw Phase Voltage Project specific Project specific Project specific Project specific Hz Project specific Project specific Project specific Project specific

5 Belt Specifications Weigh Label Tub Load (Induct) Manufacturer Ammeraal Ammeraal Ammeraal Ammeraal Part Number Thickness 7.8 mm 7.8 mm 7.8 mm 7.8 mm No of Plys Mass / m² 5 2 kg/m² 5 2 kg/m² 5 2 kg/m² 5 2 kg/m² Surface Type Tensile F for 1% Elongation Fire Rating 8.0 N/mm 8.0 N/mm 8.0 N/mm 8.0 N/mm Joiner Type Vulcanised Vulcanised Vulcanised Vulcanised Scale & Scale Operator Display Panel Specifications Manufacturer Model Number Standard is Atrax ABS960 For further details please refer to Scale Specifications.