SERVICE PARTS LIST G54A BULLETIN NO CHEST CATALOG NO. CABINET CATALOG NO SERIAL

Transcription

1 Hardware Kit Screw M x L (8) Screw M x L (8) Bolt M x L () Bolt M x L (8) Bolt M8 x L () Washer M8 () Charger Mounting Screw M x L () SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS " DRAWER STEEL STORAGE CABINET & CHEST COMBO CHEST CATALOG NO NUMBER GA CABINET CATALOG NO NUMBER GA Sep. WIRING INSTRUCTION x x 9 3x 3x 7 x Chest Lid Gas Lift (Set of ) () -9- Cord Grommet () 3 -- Cord Storage Bracket Kit () Cord Storage Bracket () Screw M x L () --3 Bracket Kit (Set of ) () Bracket () Screw M x L (8) Side Handle Kit () Side Handle () Bolt M x L () --3 Power Strip () Drawer Slide Kit (Set of ) () Inner Drawer Slide () Outer Drawer Slide () /3" Pop Rivet () Corner Bumper Kit (Set of ) () Bolt M x L (8) 3 x x x x 3 NOTE: See page for drawer slide removal and installation Corner Bumper () -- Caster Kit (Set of ) () Swivel Caster with Brake () Bolt M8 x L () Washer M8 () Rigid Caster () -- Key/Lock Kit (Set of 3) () Key (3) Lock (3) Cabinet Mat () Chest Mat () Chest Drawer Liner Kit (Set of 8) (Not Shown) () Cabinet Drawer Liner Kit (Set of 8) (Not Shown) () FIG. NOTES A second power strip is located on the inside of the top chest.

2 Cat. No shown Inner Slide To remove drawer slide, remove rivets () from the inner slide () and outer slide () by /3" drill bit. Outer Slide To install drawer slide, place inner slide () into position and insert rivets () by using a rivet gun. Repeat steps for outer slide (). Inner Slide Outer Slide

3 -9-8 SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS CATALOG NO " TOOL BOX Aug " Tool Box () 3--8 Tool Box Lid () Removable Tray () Large Insert/Hand Tool Holder () Small Insert () 3--8 Insert Kit (Contains # and #) () 3

4 Rope Gasket Seal SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS " TOOL BOX Aug. CATALOG NO Note: When installing a new Gasket Seal (3) it is recommended to start in the middle of the channel on the hinge side of the lid. Route the rope gasket along the channel with a neutral tension applied to the gasket, avoid stretching or bunching up the gasket in the channel. With your fi nger, press the gasket into the channel to seat it into position. The gasket is properly installed when the routing of the material fills the channel and there is approximately ¼ overlap of the two ends. Complete the installation by butting the two ends of the gasket material together and compressing the slight excess of material together to create a tight joint. If there is no overlap at the end of the installation, remove the gasket and start over, pulling the material slightly more taut. Latch Hinge Pin Latch Assembly Removable Tray NOTE: With the aid of a small hammer and a long, straight metal instrument like a nail, gently tap Latch Hinge Pin () to remove the pin when installing or removing Latch Assembly () " Tool Box () 3-- Removable Tray () Rope Gasket Seal () Latch Assembly () Latch Hinge Pin () Lid Hinge Pin () Latch/Seal Service Kit () Lid Hinge Pin NOTE: With the aid of a small hammer and a long, straight metal instrument like a nail, gently tap the Lid Hinge Pin () to remove the pin when installing or removing the lid. 333

5 -9-83 SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS CATALOG NO " JOBSITE ORGANIZER Dec. Note: When installing a new Gasket Seal (3) it is recommended to start in the middle of the channel on the hinge side of the lid. Route the rope gasket along the channel with a neutral tension applied to the gasket, avoid stretching or bunching up the gasket in the channel. With your fi nger, press the gasket into the channel to seat it into position. The gasket is properly installed when the routing of the material fills the channel and there is approximately / overlap of the two ends. Complete the installation by butting the two ends of the gasket material together and compressing the slight excess of material together to create a tight joint. If there is no overlap at the end of the installation, remove the gasket and start over, 3 Rope Gasket Seal Removable Bin Kit consists of one () large bin and four () small bins Front Handle (with pins) " Jobsite Organizer () 3-- Removable Bin Kit ( Big and Small) () Rope Gasket Seal () --7 Side Latch Assembly (Set of ) () --7 Front Latch Assembly (Set of ) () 3--7 Handle Kit () Front Latch (Set of ) Side Latch (Set of ) Find more Milwaukee products on our website. Check out the collection of storage & organizers we offer.