P-TWO INDUSTRIES INC.

Transcription

1 DOC. NO.: -A ISSUE DATE: CUSTOMER: PART NAME: PART NO.: APP. DATE: MANUFACTURER SIGNATURE P-TWO INDUSTRIES INC. NO. 9, SHIN HWA RD, KWEI SHAN IND. PARK TAOYUAN, 330 TAIWAN, R.O.C. TEL: FAX: P-TWO INDUSTRIES(H.K) CO.LTD. NO.17-20,HONGYE 13RD.138 INDUSTRIAL ZONE.TANGXIA TOWN DONGGUAN,GUANGDONG,CHINA TEL: FAX: P-TWO TECHNOLOGY CO.,LTD. NO HUA SHAN RD.FENG QIAO INDUSTRIAL PARK OF SUZHOU NEW DISTRICT,JIANGSU,CHINA TEL: FAX:

2 TABLE OF CONTENT I. SPECIFICATION OF PRODUCT II. III. IV. ORDERING INFORMATION CONTACT MATERIAL CERTIFICATE OF TERMINAL CONTACT MATERIAL CERTIFICATE OF SHELL V. CONTACT MATERIAL CERTIFICATE OF GROUND VI. PLASTIC MATERIAL CERTIFICATE OF HOUSING VII. MATERIAL REFERENCE TABLE VIII. THE CONFIRMATION OF PROHIBITED/CONTROLLED SUBSTANCES IX. ENGINEERING DRAWING OF PRODUCTS INCLUDE PRODUCT & PACKAGE 1 of 14

3 SPECIFICATION OF PRODUCT 1. Scope This product specification contains the test method, the general performance and requirement for interconnection system connectors. The specification covers LVDS 1.0 PITCH series connectors manufactured by P-TWO INDUSTRIES INC. 2..Applicable documents: The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1 Military Standard and Specifications: MIL-STD-1344 Test Methods for Electrical Component Parts. MIL-STD-202 Test Methods for Electronic and Electrical Component Parts 3.Requirements: 3.1 Designs and Construction: Product shall be of the design,construction and physical dimensions specified in the applicable product drawing. Materials: A. Terminal:Copper Alloy C5210R-SH,t=0.15mm. Plating: Connecting Area is plated with Gold 5μ Min.,Overall Bright TIN(LEAD FREE)75μ Min. Nickel 50μ Min. underplated B. Ground:Copper Alloy C5191R-H,t=0.15mm. Plating : Bright TIN (LEAD FREE)100μ Min., Overall Nickel 50μ Min.under plated. C. Shell:Stainless Steel SUS304R-3/4H,Solder Area Gold 4μ Min.,Overall Nickel 10μ Min. underplated. D. Housing:Heat Resistance Plastic, LCP (UL94 V-0) 4. Characteristics Voltage rating: 200V DC Current rating: 1 Amps/Contact Storage temperature range: -40 C to +80 C 5. GP requires substances (level1) forbidden (including orders placed to subcontractors) 2 of 14

4 6. Mechanical Performance Item Description Test method & Condition Requirement It should be tested in accordance Contact with method 2007 of MIL-STD-1344A.The end of 6-1 Retention force 1.5N Min. terminal shall be pulled in a perpendicular to base housing at a constant speed of 25mm/minute. 6-2 Durability 50 cycle of inserting and separating action are conducted and measure contact. Low level contact resistance: 80mΩ Max. 6-3 Mating force Insertion is conducted between applicable connectors.(without 1.96N X n Max. locking lever) n =number of pins 6-4 Unmating force 6-5 Vibration 6-6 Shock SPECIFICATION OF PRODUCT Separation is conducted between applicable connectors.(without locking lever) In accordance with method 2 of MIL-STD-202, all contacts shall be connected in series and DC 100mA shall be applied. Wave form: Sine wave. Frequency: HZ Amplitude: 1.5mm Orientation: X,Y,Z (3 axes). Duration: 2hrs/axis In accordance with method 202 of MIL-STD-202. DC 100mA shall be applied. MAX acceleration:50g Wave form: Half sine wave. Orientation: X,Y,Z(3 axes). Duration: 11ms/axis. Times: 3 time/axis 0.25N X n Min. n =number of pins There shall be no current discontinuity of more then 1μ sec. And there shall be no mechanical defect defected on the parts during and after test. 3 of 14

5 SPECIFICATION OF PRODUCT 6-7 Lock strength Measure force necessary to unmate from a lock state. 44N Min. 7. Electrical performance Item Description Test method & Condition Requirement The connector shall be tested in 7-1 Dielectric accordance with method 30of There shall be no MIL-STD-1344A. When the 500V AC current leakage withstanr.m.s for one minute applied between and flashover or -ding voltage adjacent contacts. damage detected Insulation resistance Contact resistance It should be tested in accordance with method 3003 of MIL-STD-1344A. When 100V DC is applied between adjacent contacts and insulation resistance is measured within one minute. It should be tested in accordance with method 3004of MIL-SDT-1344A. Measure by low level (Max:20mV, 100mA) 100MΩ Min. 40mΩ Max. 8.Environmental performance Item Description Test method & Condition Requirement There shall be no short circuiting and Damage detected Subject mated connectors to steady at AC 500V r.m.s state humidity at 60 and 90~95% 8-1 Humidity Insulation R.H. to 96 hours. (steady state) Resistance: Min. MIL-STD-202, Method 103, 50MΩ (96 hours) Contact resistance: Max. 80mΩ. 4 of 14

6 SPECIFICATION OF PRODUCT 8-2 Thermal shock 8-3 Salt spray 8-4 Temperature life Cold 8-5 Temperature life High 8-6 Solderability 8-7 Soldering Heat Withstanding Subject specimens to continuous 5 cycles between -55 C and +85 C for 30minutes each. Connector shall be tested in accordance with method 10 of MIL-STD-202. Temperature:35±2 Density:5% in weight Duration:48 hours In accordance with method IEC method. The specimens subjected to the chamber temperature of -40±2 for 96 hours. In accordance with method MIL-STD-202 method 108. The specimens subjected to the chamber temperature of 80±2 for 96 hours. The end of post shall be dipped in accordance with method 208 of MIL-STD-202. SolderingTemperature: 245±5 C Soldering time: 5±0.5 sec It should be tested to compare with method 210 of MIL-STD-202. Soldering temperature: 260±5 C Duration time:5±0.5 sec. Consecutive 3 cycles Appearance is no damage. Contact resistance is 80mΩ max. resistance: Max. 80mΩ. Contact Resistance: 80MΩ MAX. Appearance neither damage nor crack. Contact Resistance: 80mΩ MAX. Appearance neither damage nor crack. More than 95% of the immersion shall be covered with solder No physical damage 8-8 H 2 S Gas H 2 S gas density: 3 ppm Temperature: 40 C Duration:96hours Contact Resistance: 80mΩ Max 5 of 14

7 SPECIFICATION OF PRODUCT 8-9 NH 3 Gas Ammonia density:28% Duration:72hours Contact Resistance: 80mΩ Max 6 of 14

8 ORDERING INFORMATION LVDS 1.0 mm PITCH CONNECTOR SMT TYPE Specifications: LVDS (FEMALE) Connectors Connector Styles: SMT Type Sunk-into-the-board type (Board back mounting) Centerline (Pitch): 1.00 mm (0.04 inch) No. of Contacts: 30 PIN (1) (2) (3) (1) 30: PIN NO. (2) 09: PLATEING GOLD with BRIGHT TIN(100%) (3) 1: PACKAGED CARRIER 7 of 14

9 CONTACT MATERIAL CERTIFICATE OF TERMINAL 8 of 14

10 CONTACT MATERIAL CERTIFICATE OF SHELL 9 of 14

11 CONTACT MATERIAL CERTIFICATE OF GROUND 10 of 14

12 PLASTIC MATERIAL CERTIFICATE OF HOUSING 11 of 14

13 PLASTIC MATERIAL CERTIFICATE OF HOUSING 12 of 14

14 PLASTIC MATERIAL CERTIFICATE OF UL YELLOW CARD QMFZ2 Component - Plastics Friday, August 10, 20 E POLYPLASTICS CO LTD VECTRA DIV, KASUMIGASEKI BLDG, 6TH FL 2-5 KASUMIGASEKI 3-CHOME CHIYODA-KU TOKYO JAPAN Material Designation: E130i(d)(e) Product Description: Liquid Crystal Polymer (LCP), thermotropic aromatic polyester, designated "Vectra" furnished as pellets. Color Min. Thick. (mm) Flame Class HWI HAI RTI Elec RTI Imp RTI Str IEC GWIT IEC GWFI ALL 0.75 V V V CTI: 4 HVTR: 0 D495: 5 IEC BP: - (d) (e) Virgin and regrind up to 50% by weight incl. have the same basic material characteristics for colors NC and BK. In addition, regrind at 26 to 50% have the same basic characteristics at a minimum of 1.5mm except RTI's for the Mechanical w/impact property is 180C. Report Date: 08/19/1992 Underwriters Laboratories Inc UL94 small-scale test data does not pertain to building materials, furnishings and related contents. UL 94 small-scale test data is intended solely for determining the flammability of plastic materials used in components and parts of end-product devices and appliances, where the acceptability of the combination is determined by ULI. 13 of 14

15 MATERIAL REFERENCE TABLE Parts Name General Name Model No. Terminal Copper Alloy C5210R-SH Heat Resistant Level UL Card No. Specific Weight 0.075g 13% Housing L.C.P E130I UL94 V-0 E Shell Stainless Steel SUS304R-3/4H 0.193g 34% 0.244g 43% Ground Copper Alloy C5191R-H 0.064g 11% 14 of 14

16

17

18

19