SCHMEISER S TINE SEEDER 2 nd GENERATION SERIES 98 ASSEMBLY & PARTS MANUAL

Transcription

1 SCHMEISER S TINE SEEDER 2 nd GENERATION SERIES 98 ASSEMBLY & PARTS MANUAL T.G. SCHMEISER CO., INC. P.O. BOX 1112 FRESNO, CA (559) FAX (559) COPYRIGHT 2007 T.G.SCHMEISER CO., INC. VERSION 2.2 MAY 2007

2 INTRODUCTION Your Schmeiser S-Tine Seeder is designed to give you many years of dependable service. This manual has been prepared to instruct you in the safe and efficient operation of this machine. Read and study it thoroughly. Follow all instructions carefully. Should your S-Tine Seeder require replacement parts, go to your Schmeiser dealer. Always order genuine Schmeiser replacement parts. It is important that you complete and send in your Warranty Card because it is not valid unless it is on file at Schmeiser. If you need information not contained in this manual, contact your Schmeiser dealer. Space has been provided below for you to record the model number and serial number of your seeder. Be sure to bring this information with you to your dealer when ordering parts or attachments for your seeder. Thank you for buying a Schmeiser S-Tine Seeder. SERIAL NUMBER MODEL NUMBER DATE PURCHASED DEALER NAME 2

3 TABLE OF CONTENTS Introduction...2 Table of Contents...3 Safety Rules...4 Seed Cup Seed Rate Calibration Seed Rate Chart....7 Planting Depth Adjustments...8 Sprocket and Chain Assemblies S-Tine Seeder Box Assembly...10 Feeder Cup and Drive Components Feeder Cup Assembly Main Frame and Wheel Leg Assemblies Jack Shaft, Sprocket, Idler and Bearing Assemblies S-Tine and Hose Assemblies Limited Warranty Maintenance and Repair Record Notes

4 SAFETY RULES The safe operation of any machinery is a big concern to farmers and manufacturers. We have designed our S-Tine Seeder with many built-in safety features. However, no one should operate this machine before carefully reading this Owner s Manual. 1. Never permit anyone to ride on or walk beside the S-Tine Seeder when moving. 2. Never permit anyone to ride on tractor when S-Tine Seeder is being moved. 3. Never allow anyone to be near the S-Tine Seeder when performing operating functions with seeder or tractor. 4. Never load S-Tine Seeder without being hooked-up to tractor. 5. Extra care should be taken when transporting with seed in the box. 6. Never back S-Tine Seeder up when s-tines are in ground. 7. Reduce speed of tractor when transporting over uneven or rough terrain. Avoid all chuck holes and washboard areas in road. 8. Reduce speed of tractor when transporting over hills or steep slopes. 9. Always set S-Tine Seeder in field position before lubrication. 10. Do NOT lubricate, adjust or repair the S-Tine Seeder while it is in operation. 11. When in transport, use accessory lights and devices for adequate warning to operators of other vehicles, and use safety chains. Comply with all Federal, State and local laws when traveling on public roads. 12. Use Slow Moving Vehicle emblem for warning vehicles approaching from rear. 13. Do NOT permit smoking, sparks, or an open flame where combustible lubricants, or liquids are being used. 14. When using treated grain, avoid direct contact with the seed. 15. When using compressed air to clean S-Tine Seeder, wear safety glasses. 16. When transporting, remember the S-Tine Seeder may be wider that your tractor and extreme care must be taken to allow for safe clearance. 4

5 SEED CUP IMPORTANT: Be sure to adjust seed cup lever position prior to loading seed in hopper. WARNING: Closing seed lever with seed in cup may damage or break lever. It is important to select the correct lever position. The incorrect position may cause a) seed damage and/or b) cup damage. Small Seed Position Clean Out Position Medium Seed Position Large Seed / Mixed Seed Position 5

6 SCHMEISER S-TINE SEEDER SEED RATE CALIBRATION Note: Seeding rates will vary greatly with variations in sizes of seeds. Although the seeding rates listed in this manual are based on an average seed size, we recommend that you test and adjust your S-Tine Seeder using the procedures listed below. 1) There are many factors, which will affect seeding rates: Seed treatment, weight of seed, size of seed, surface condition of seed, tire configuration and pressure, and tire slippage. Minor adjustments will probably be needed to compensate for the above factors. 2) The rates listed in the seed charts are based in the gauge wheel drive having 20.5 x 8.0 x 10 tire with the recommended tire inflation. 3) The large difference in seed size and treatment can cause a wide variation in actual seeding rates. The rate charts are based on average size seed. This may differ from the seed you are using. Use the seed rate charts as a guide only. Set the pounds per planted acre desired at the indicator number and complete the following procedure to calibrate the rate for specific seed. a. Place several pounds of seed over three feeder cups at the outboard end of the S-Tine Seeder. b. Pull the seed tubes out of these three drops. c. Raise the drive wheel off the ground using a jack. d. Rotate the tire to see that the drive system is working properly and that the feed cups are free from foreign matter. e. Place a container under the three seed tubes to gather seed as it is metered. f. On 4 ft. wide models rotate the tire 48 times to obtain 1,000 square feet. On 5 ft. wide models rotate the tire 38 times to obtain 1,000 square feet. On 6 ft. models rotate the tire 32 times to obtain 1,000 square feet. Be sure to check the three feeder cups to make sure each cup has plenty of seed coming into it. g. Weigh the seed, which has been metered. Divide by three. This will give you the ounces/pounds metered by each feeder cup. Multiply by the number of cups on your S-Tine Seeder to arrive at the total pounds per 1,000 square feet. Now multiply by to arrive at the total pounds per planted acre. If this figure is different than desired, set your feed cup adjustment lever accordingly. 4) You may want to repeat the calibration procedure if the results of your calibration vary greatly from the suggested settings contained in this manual. REMEMBER: Tire size and field conditions will also affect seeding rates. Be certain that your S- Tine Seeder tires are 20.5 x 8.0 x 10 and that they have the proper inflation. When seeding, check the amount of seed you are using by noting area seeded, amount of seed added to box, and level of seed in seeder box. If you suspect that you are seeding more or less seed than desired, and you have accurately calibrated the S-Tine Seeder to your seed, you may need to adjust the seeding rate slightly to compensate for your field conditions. 6

7 SEEDING RATES FOR SCHMEISER S-TINE SEEDER 2 ND GENERATION SERIES 98 Rates in Pounds per Planted Acre August 1, 2001 Sprocket Combination: 13/33 x 12/33 Seed Rate Indicator Setting Number Seed POUNDS PER ACRE Barley Bio Max Cover Crop* Clover - Perennial Cover Crop Mix #1* Cover Crop Mix #2* Cover Crop Low Profile* Cover Mate Mix* Crimson/Berseem Insectary Mix* Pearl Millet Rye Grass - Annual Sorghum Sudan Sudan Bravo Brand Vetch - Common Winter Forage #1* CAUTION: THESE RATES ARE APPROXIMATE ONLY. PLEASE VERIFY OUTPUT PRIOR TO FIELD USE. * Germain's Seed THIS CHART APPLIES TO S-TINE SEEDERS MANUFACTURED AFTER JANUARY 2001 NOTE: INSURE THAT SQUARE SEED CUP SHAFT IS WELL LUBRICATED WHERE SHAFT GOES THROUGH CUP DRIVE BEARING (SEE Page 9.2) 7

8 PLANTING DEPTH ADJUSTMENT Your Schmeiser S-Tine Seeder is designed to run level to the ground when in planting position. Minor adjustments may be required to achieve the desired seed placement. In order to adjust your gauge wheel/drive wheel, loosen the two set screws located on the adjusting crank housing. Rotate crank to achieve desired planting depth. After adjusting the gauge wheel/drive wheel, be certain to tighten up both set screws. GUAGE / DRIVE WHEEL ADJUSTING CRANK SET SCREWS GUAGE / DRIVE WHEEL 8

9 SPROCKET AND CHAIN ASSEMBLIES DRIVE CHAIN 33T SPROCKET 15T IDLER SPROCKETS #40 CHAIN 13T SPROCKET 19T SPROCKET END CHAIN #40 CHAIN 33T SPROCKET 12T SPROCKET 15T IDLER SPROCKET 9

10 S-TINE SEEDER BOX ASSEMBLY Ref. No. Old Part No. New Part No. Description 1. VD4-C VDS-48C000 4 Vineyard Drill Lid Weldment VD5-C VDS-60C000 5 Vineyard Drill Lid Weldment VD6-C VDS-72C000 6 Vineyard Drill Lid Weldment FWASHER-05 Washer, Flat 5/ WWASHER-05 Washer, Wave Spring 5/ NYNUT-05NC Nut, Hex Nylock 5/ VD-C-07 VDS-00C007 Lid Latch-Handle D D Lid Latch Grip 7. VD-M VDS-00M000 Lid Hinge Weldment 8. VD-C-08 VDS-00C008 Lid Latch - Lower Arm CSNC Bolt, Hex Head 5/16-18 x 1 Long Gr 5 Plated 10. VD-C-12 VDS-00C012 Lid Latch Lower Latch Bushing 11. VD-C-09 VDS-00C009 Lid Latch - Upper Arm 13. VD-L-01 VDS-00L000 Float Indicator Assembly 14. VD-L-04 VDS-00L004 Float Indicator - Coupling CSNC Bolt, Hex Head 3/8-16 x 1 Long Gr 5 Plated 16. VD-B-10 VDS-00B010 Sprocket Cover Plate 17. VD4-B VDS-48B000 4 Seedbox VD5-B VDS-60B000 5 Seedbox VD6-B VDS-72B000 6 Seedbox LWASHER#10S Washer, Internal Star #10 Plated HXNUT#10NC Nut, Hex #10-24 Plated 20. VD-C-10 VDS-00C010 Rear Lid Latch Hook CSNC#10012R Screw, Round Head #10-24 x 3/4 Long Plated HXNUT-05NC Nut, Hex 5/16-18 Gr 2 Plated LWASHER-05 Washer, Lock Spring 5/16 Plated FWASHER-05 Washer, Flat 5/16 Plated HXNUT208NC Nut, Hex 1/2-13 Gr 2 Plated LWASHER-08 Washer, Lock Spring 1/2 Plated LWASHER-06 Washer, Lock Spring 3/8 Plated HXNUT506NC Nut, Hex 3/8-16 Gr VD-B-09 VDS-00B009 Vineyard Drill Lift Hooks CSNC Bolt, Hex Head 1/2-13 x 1 Long Gr GBR-12FP03 3/4 Flangette Plates GBR-12BI02 Bearing 3/4 Bore with Collar CSNC Bolt, Hex Head 1/4-20 x 1-1/2 Long Gr H H Sprocket, Speed Change 19T HXNUTJ04NC Hex Jam Nut 1/4-20 Plated CBNC Bolt, Carriage 5/16 x 3 4 Long Gr VD4-G-09 VDS-48G200 4 Agitator Weldment VD5-G-09 VDS-60G200 5 Agitator Weldment VD6-G-09 VDS-72G200 6 Agitator Weldment BALL-64OD Float Indicator Float 39. VD-L-03 VDS-00L100 Float Indicator Shaft Bracket Weldment GMB-CHFLIN Float Indicator Chain Long SHOOK-16 S Hook, LCOLLAR-05 Lock Collar, 5/ FWASHER-06 3/8 Flat Washer CSNC Bolt, Hex Head 5/16 x

11 11

12 FEEDER CUP AND DRIVE COMPONENTS Ref No. Old Part No. New Part No. Description 1. VD-B VDS-48B000 4 Box Weldment VDS-60B000 5 Box Weldment VDS-72B000 6 Box Weldment 2. VD-K-01 VDS-48K001 4 Cup Tray VDS-60K001 5 Cup Tray VDS-72K001 6 Cup Tray 3. VD-K-03 VDS-00K003 Pivot Handle Adjustment Mount 4. VD-K-02 VDS-00K100 Seed Rate Adjustment Handle H H Adjustment Lock Plate 6. VD-K-04 VDS-00K004 Gauge Mounting Plate 8. VD-K-07 VDS-SRINDP Seed Rate Indicator Plate CSNC#10008R Screw, Round Head #10 x FWASHER#10 Washer, Flat # LWASHER#10S Washer, Internal Star # HXNUT#10NC Nut, Hex # CSNC Bolt, Hex Head 3/8-16 x 3/4 Long LWASHER-06 Washer, Lock 3/8 Plated FWASHER-06 Washer, Flat 3/8 Plated D D Adjustment Handle Pivot Bushing GPN-03X32C Pin, Cotter 3/16 x 1-1/4 Long Plated D D Seed Adjustment Bearing Ring Pivot FWASHER-05 Washer, Flat 5/16 USS Plated NYNUT-05NC Nut, Nylon Self Locking Hex 5/ HXNUT-04NC Nut, Hex 1/ CBNC Bolt, Hex Carriage 1/4-20 x 3/4 Long WGNUT-08NC Nut, Wing 1/2-13 Plated FWASHER-10 Washer, Flat 5/8 Plated FWASHER-08 Washer, Flat 1/ CBNC Bolt, Hex Carriage 1/2 x 1-1/4 12

13 FEEDER CUP AND DRIVE COMPONENTS INSURE THAT SQUARE SEED CUP SHAFT IS LUBRICATED WHERE SHAFT GOES THROUGH CUP DRIVE BEARING. 13

14 FEEDER CUP ASSEMBLY Ref. No. Part No. Description 1. VD4-K-01 VDS-48K001 4 Seed Cup Tray VD5-K-01 VDS-60K001 5 Seed Cup Tray VD6-K-01 VDS-72K001 6 Seed Cup Tray CBNC Bolt, Carriage 1/4-20 x 3/4 Long D C Feeder Cup Shaft Locking Collar C C Screw, Set Knurled Point 5/16-18 x 3/8 Long LWASHER-04 Washer, Lock 1/ C HXNUT-04NC Nut, Hex 1/4-20 Gr.5 Plated 7. VD-K D Spacer Tube 3-9/16 Long S S Sprocket Shaft Adjustment Bearing Assembly C C Powder Metal Sprocket C C Seed Cup Assembly C C Seed Cup Adjustment Handle C C Cup Sleeve C C Washer, Retaining C C Ring, Snap External 1-3/ C C Ring, Snap Internal C C Bearing, 30mm B x 55mm OD D D Cup Drive Bearing Housing 18. VD-K-07 VDS-00K007 Cup Drive Sprocket Weldment 19. VD4-K-05 VDS-48K005 4 Seed Cup Shaft VD5-K-05 VDS-60K005 5 Seed Cup Shaft VD6-K-05 VDS-72K005 6 Seed Cup Shaft CSNC Bolt, Hex Head 3/8-13 x 3/4 Gr LWASHER-08 Washer, Lock Spring 1/2 Plated V V Cup Drive Housing Assembly Includes 1 Each of Items 15 through 17 14

15 FEEDER CUP ASSEMBLY

16 MAIN FRAME & WHEEL LEG ASSEMBLIES Ref No. Old Part No. New Part No. Description Qty. 1. ST4-A STS-48A000 4 Main Frame 1 ST5-A STS-60A000 5 Main Frame 1 ST6-A STS-72A000 6 Main Frame 1 2. VD-J VDS-00J000 Jack Screw 1 3. VD-E VDS-00E000 Wheel Leg 1 4. VD-D VDS-00D000 Wheel Shaft 1 5. VD-F-01 GPN-18CA12 Clevis Pin Cat. I & II 2 6. VD-J-02 VDS-00J100 Set Screws 2 7. VD-G-10 VDS-00G010 Sprocket Key 1 8. VDB-01 GSR-17112T 7 Tension Spring 1 9. VDB-04 GHB-5X4GSL Oil Seal VDB-05 GHB-5X4BCN Bearing Cone VDB-06 GHB-5X4BCP Bearing Cup VDB-07 GHB-5X45VD Hub, 5 Studs Complete 1 GHB-5X4HUB Hub Body with Bearing Cups (pressed in) 13. VDB-08 GSP-16VDCN Castle Nut VDB-09 GHB-5X4CAP Hub Cap VDB-10 GWT x 8 x 10 Tire with Wheel, 5 on VDB-12 WHN-08NFWN Lug Nuts VDB-14 GSK-12BS13 13 Tooth Sprocket CSNC x 5-1/2 Hex Head Gr 5 z/p Bolts CSNC x 4 Hex Head Gr 5 z/p Bolts HXNUT-16NC 1 Hex Nuts GPN-04X24C 1/4 x 1-1/2 Cotter Pin GPN-070LYN 7/16 x 1-3/4 Lynch Pins 2 16

17 MAIN FRAME & WHEEL LEG ASSEMBLIES

18 JACK SHAFT, SPROCKET, IDLER & BEARING ASSEMBLIES Ref No. Old Part No. New Part No. Description Qty. 1. VD4-G-06 VDS-48G006 4 Jack Shaft 1 VD5-G-06 VDS-60G006 5 Jack Shaft 1 VD6-G-06 VDS-72G006 6 Jack Shaft 1 2. VD-G-02 VDS-00G002 End Plate Tensioner Arm 1 3. VD-G-01 VDS-00G001 Center Tensioner Arm & Spring Anchor 1 4. VD-G-03b VDS-00G102 Bushing, 13/16 Long 2 5. VD-G-03 VDS-00G100 Spring Anchor 1 6. VD-G-04 VDS-00G004 Bushing, 1/2 Long 2 7. VD-G-05 VDS-00G005 Bushing, 1-1/4 Long 1 8. VDB-01 GSR-17112T 7 Tension Spring 1 9. VDB-02 GSR-10040T 2-1/2 Tension Spring VDB-33TS GSK-12BS33 33 Tooth Sprocket VDB-15I GSK-08ID15 15 Tooth Idlers VDB-12TS GSK-12BS12 12 Tooth Sprocket VDB-03 GBR-12BI02 Stamped Flange Bearing with Collar, 3/ CBNC /16 x 1 Carriage Square Neck Bolts CSNC /2 x 2 Hex Head Gr 5 z/p Bolt CSNC /2 x 2-1/2 Hex Head Gr 5 z/p Bolt CSNC /2 x 3-1/2 Hex Head Gr 5 z/p Bolt LWASHER-05 5/16 Lock Washers LWASHER-08 1/2 Lock Washers FWASHER-08 1/2 Flat Washer HXNUT-05NC 5/16 Hex Nuts HXNUT-08NC 1/2 Hex Nuts NYNUT-08NC 1/2 Nylon Locknuts VD-G-10 VDS-00G010 Sprocket Key VDS-CH4064 #40 Roller Chain 63 1/2 Long VDS-CH4055 #40 Roller Chain 54 1/2 Long Set Screw, 3/ S S Feeder Cup Bearing Assembly H 19 Tooth Speed Change Sprocket FWASHER-05 5/16 Flat Washer 4 18

19 14 JACK SHAFT, SPROCKET, IDLER & BEARING ASSEMBLIES

20 S-TINE & HOSE ASSEMBLIES Ref No. Old Part No. New Part No. Description C C 1-5/8 Hose Clamp # C C Seed Hose 33 Ribs 3. ST-BO-01 GMB-HCLAMP22 1-3/8 Hose Clamp 4. ST-A-20 GMB-HOSE16 1 Green Hose 16 Long 5. ST-BO-02 GMB-WGHC32 Green Hose Clamps CSNC x 4 Hex Head Gr. 5 Bolt LWASHER Lockwasher HXNUT-08NC 1 2 Hex Nut 9. ST-BO-03 GST-2CL /2 Tool Bar Clamp 10. ST-BO-04 GST-50125S 1 2 x1-1/4 S-Tines 11. ST-BO-05 GST-25150P S-Tine Points 12. ST-BO-06 } Elliptical Head Bolt M10 x 38 with Nut GST-0624BN Assembly 13. ST-BO-07 20

21 S-TINE & HOSE ASSEMBLIES

22 T.G. SCHMEISER CO., INC. Limited Warranty Statement T. G. Schmeiser Co., Inc. warrants each new Schmeiser product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed twelve (12) consecutive months from the date of delivery of the new Schmeiser product to the original purchaser. Genuine T. G. Schmeiser Co., Inc. replacement parts and components will be warranted for 90 days from date of purchase, or the remainder of the original equipment warranty period, whichever is longer. Under no circumstances will it cover any merchandise or components thereof, which, in the opinion of the company, has been subjected to misuse, unauthorized modifications, alteration, an accident or if repairs have been made with parts other than those obtainable through T. G. Schmeiser Co., Inc. The Company in no way warrants engines, batteries, cylinders, tires or other trade accessories since these items are warranted separately by their respective manufacturer. Expendable components such as points, shanks, blades, rings, bearings, teeth, and the like are excluded from this warranty. Our obligation under this warranty shall be limited to repairing or replacing, free of charge to the original purchaser, any part that, in our judgment, shall show evidence of such defect, provided further that such part shall be returned within thirty (30) days from date of failure to T. G. Schmeiser Co., Inc., routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. This warranty shall not be interpreted to render T. G. Schmeiser Co., Inc. liable for injury or damages of any kind or nature to person or property. This warranty does not extend to the loss of crops, loss because of delay in harvesting, or any expense or loss incurred for labor, substitute machinery, rental or for any other reason. Except as set forth above, T. G. Schmeiser Co., Inc. shall have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages. T. G. Schmeiser Co., Inc. makes no other warranty, expressed or implied, and, specifically, T. G. Schmeiser Co., Inc. disclaims any implied warranty or merchantability or fitness for a particular purpose. Some states or provinces do not permit limitations or exclusions of implied warranties or incidental or consequential damages, so the limitations or exclusion in this warranty may not apply. This warranty is subject to any existing conditions of supply, which may directly affect our ability to obtain materials or manufacture replacement parts. T. G. Schmeiser Co., Inc. reserves the right to make improvements in design or changes in specifications at any time, without incurring any obligation to owners of units previously sold. No one is authorized to alter, modify or enlarge this warranty nor the exclusion, limitations and reservations. WARRANTY VOID IF NOT REGISTERED WITHIN 30 DAYS OF PURCHASE DATE 22

23 Schmeiser S-Tine Seeder Maintenance & Repair Record Date of Service or Repair Performed Parts Service Replaced 23

24 Notes 24