LVH. VERTICAL GLASS HOT FOOD/DELI MERCHANDISERS Hot Temperature Service Display Cases. Save the Instructions in this Manual for Future Reference!!

Transcription

1 Installation & Service Manual VERTICAL GLASS HOT FOOD/DELI MERCHANDISERS Hot Temperature Service Display Cases Save the Instructions in this Manual for Future Reference!! This merchandiser conforms to the Commercial Refrigeration Manufacturers Association Health and Sanitation standard CRS-S1-96. PRINTED IN Specifications subject to REPLACES ISSUE PART IN U.S.A. change without notice. EDITION 1/97 DATE 7/99 NO REV. B Tyler Refrigeration Corporation * Niles, Michigan 49120

2

3 Installation & Service Manual CONTENTS Page Warranty Installation Procedures Usage General Information Proper Use of the Hot Food Deli Service Case Air Vent Adjustments Care and Upkeep Operations Steam Table Operation Instructions Cleaning Instructions Wiring Diagrams Wiring Diagram /240 Volt 60Hz 1Ph. 3W Wiring Diagram /240 Volt 60Hz 3Ph. 4W Wiring Diagram /240 Volt 60Hz 1Ph. 3W Wiring Diagram /240 Volt 60Hz 3Ph. 4W Wiring Diagram /240 Volt 60Hz 3Ph. 4W Miscellaneous Rear Sliding Door Removal and Installation Control and Locations Double Heat Lamp Assembly Installation Check List Parts Information Operational Parts List Cladding and Trim Parts List The following Hot Temperature Vertical Glass Service/Deli Merchandiser models are covered in this manual: MODEL DESCRIPTION 4, 6 & 8 VERTICAL GLASS HOT FOOD SERVICE/DELI MERCHANDISER January, 1997 Page 3

4 Tyler Refrigeration Page 4 October, 1996

5 Installation & Service Manual October, 1996 Page 5

6 Tyler Refrigeration Page 6 October, 1996

7 Installation & Service Manual October, 1996 Page 7

8 Tyler Refrigeration Page 8 October, 1996

9 Installation & Service Manual October, 1996 Page 9

10 Tyler Refrigeration Page 10 October, 1996

11 Installation & Service Manual October, 1996 Page 11

12 Tyler Refrigeration Wiring Diagram /240V 60Hz 1Ph 3W Page 12 October, 1996

13 Installation & Service Manual Wiring Diagram /240V 60Hz 3Ph 4W October, 1996 Page 13

14 Tyler Refrigeration Wiring Diagram /240V 60Hz 1Ph 3W Page 14 October, 1996

15 Installation & Service Manual Wiring Diagram /240V 60Hz 3Ph 4W October, 1996 Page 15

16 Tyler Refrigeration Wiring Diagram /240V 60Hz 3Ph 4W Page 16 October, 1996

17 Installation & Service Manual The sliding doors come installed from the factory in the door frame. These doors are removable for cleaning and to aid in case maintenance. NOTE: DO NOT FULLY IMMERSE DOORS WHEN CLEANING. 1. Remove the outer door by first sliding it to the right end of the door frame (within an inch of being closed). 2. Firmly grasp either side of the door and lift into the upper track until it clears the lower track. 3. Tilt the door so that the bottom comes out of the track. 4. Lower the door so that it seperates from the upper track. The door should now be free. Next remove the inner door in the same manner. To replace the doors follow the above steps in the reverse sequence. First check to see that the sealing strips are in their proper place. Remember to insert the inner door first. July, 1999 Page 17

18 Tyler Refrigeration Page 18 October, 1996

19 Installation & Service Manual October, 1996 Page 19

20 Tyler Refrigeration Page 20 October, 1996

21 Installation & Service Manual PARTS INFORMATION Operational Parts List Case Usage Electrical Circuit Domestic 115 Volt 60 Hertz Case Size Fuse Holder Fuse Toggle Switch T Handle* Infi-Switch* Reostat Switch* Steam Table, assembled includes Heat Element, Insulation & Electrical Wires* Steam Table, unassembled Table Pan Only* Heat Element, Wet & Dry Units* Heat Element. Dry Unit Only* Reservoir, Auto-Fill* Way Valve* Red Pilot Light * = (1) per well For information on operational parts not listed above contact the TYLER Service Parts Department. January, 1997 Page 21

22 Tyler Refrigeration Cladding and Trim Parts List Item Description Screw (2) (2) (2) 2 Top Joint Trim, BRT SS Tape Outer Glass Joint Trim, BRT SS 5 Bumper Retainer Color Band, Painted Color Band Backer Bumper End Trim(per patch end) color per order Bumper Backer color per order Bumper color per order Screw (10) (14) (18) 12 Rivet (3) (4) (5) 13 Upper Front Cladding, Painted Screw (4) (6) (10) 15 Kickplate color per order Kickplate Backer Screw (4) (6) (6) 17 Kickplate Support (2) (3) (3) 18 Lower Front Cladding, Painted LH End Close-off, Painted RH End Close-off, Painted Screw (3) (3) (3) 21 Horizontal Joint Trim, BRT SS RR Base Joint Trim, Ptd Screw (4) (4) (4) 24 Screw (4) (4) (4) 25 RR Lower Joint Trim, BRT SS Screw (4) (4) (4) 27 RR Upper Joint Trim, BRT SS Inner Glass Joint Trim, BRT SS Page 22 July, 1999

23 Installation & Service Manual July 1999 Page 23