Siai Marchetti SF-260

Transcription

1 Thank you for choosing CYmodel Global : ustralia : Italia : Siai Marchetti SF-0 Instruction Manual efore commencing assembly, please read these instructions thoroughly. SFETY PRECUTIONS This radio control model is not a toy lfirst-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent., lssemble this kit only in places out of children s reach ltake enough safety precautions prior to operating this model., You are responsible for this model s assembly and safe operation llways keep this instruction manual ready at hand for quick reference,even after completing the assembly. lcould cause serious injury or even death Designed and Manufactured by : CYmodel SPECIFICTION Wing span... 8 mm (90 in) Wing area...8 dm (97 sq.in) Empty weight...7. kg Total length mm (70.5 in) Engine cc gas engine Radio... channels 8 servos Item Nr: Cy8 Http : //

2 REQUIRED FOR OPERTION (Purchase separately) minimum channel radio for airplanes (with 8 servos). nd dry batteries. Silicone Tube Fuel Filter CUTION: Only use a minimum channel radio for airplanes (No other radio may be used) 5 required for engine starting engine fuel minimum channel transmitter for airplanes. WRNING: Normal gasoline cannot be used with glow engines. -size atteries Fuel Pump Plug Wrench For handing the radio properly.refer to its instruction manual. Engine and Muffler Model irplane engine 5-50 cc gas engine Muffler Glow plug Glue 7 Other Instant glue equipment for enhancing airplane operation & perormance Epoxy Glue Purchase a propeller that Propeller splinner will match your engine Engine Starter V attery (for starter) TOOLS REQUIRED ( Purchase separately) Sharp Hobby Knife Phillips Driver wl Needle Nose Pliers Wire Cutters Scissors... EFORE YOU EGIN Read through the manual before you begin,so you will have an overall idea of what to do. Check all parts.if you find any defective or missing parts.contact your local deater. Symbols used throughout this instruction manual,comprise. pply epoxy glue. pply instant glue (C glue,super glue). mm Drill holes with the specified Diameter(here:mm) Ensure smooth non-binding movement while assembling. Must be purchased separately Pay close attention here Warning Do not overlook this symbol. ssemble left and right Sides the same way. Cut off shaded portion. Cut off excess.

3 ccessory list for this page. Install the lamp-chimney Hinge Epoxy pin hings to aileron steadily Install the lamp-chimney L R Warning Securely glue together,if coming off during. You will lose control of your airplane which leads to accidents Hinge Install the lamp-chimney 5 Install the lamp-chimney 0mm mm lcak line attery Red line

4 8 ccessory list for this page. MX5mm MX0mm screw -- MX0mm screw X85mm Rod MX0mm R MX0mm screw -- MX0mm screw mm steel wire 5.mm Collar Rod 5.mm Collar ---- Xmm screw mm Nut ---- Xmm screw MX0mm M Lock Nut MX5mm -- M Lock Nut X0mm L Xmm Tp screw Install the main landing gear Xmm screw xmm Xmm screw Install the aileron ssemble the landing gear to the wing with screw Xmm Tp screw Install the aileron servo L ileron servo L ssemble the front-wheel drive R MX0mm mm steel wire ---- MX5mm X85mm Rod ---- MX5mm MX0mm ---- Rod mm Nut xmm ---- X0mm R

5 ccessory list for this page. ssemble the wings to the fuselage X0mm Tp screw mm Washer M Lock Nut Pin hings --- Nylon nut Hinge Nylon nut ssemble the front-wheel drive to the fuselage with screw Epoxy the horizontal tail X0mm Tp screw L R Warning Securely glue together,if coming off during. You will lose control of your airplane which leads to accidents Hinge ssemble the front-wheel drive 5 Install the rudder Pin hings mm Washer M Lock Nut Warning Securely glue together. If coming off during flights,you'll lose control of your airplane which leads to accidents 5

6 --- MX8mm cap screw luminum tube (xmm) MX5mm screw 0 Steel wire Mx8mm cap screw Copper joiner x5mm Mx0mm Fiberglass tube Secure the servo. Install the nylon control horn and connect the linkage Copper joiner x5mm Elevator rod luminum tube (xmm) 9 ssembly of the stabilizer C luminum tube (xmm) C x5mm Mx8mm cap screw x5mm mm Nut ssemble the servo to the fuselage Copper joiner = C=C D=D Steel wire mm Nut 8 ccessory list for this page MX8mm cap screw Rudder servo D D Securely glue together,if coming off during flights. You lose control of your airplane which leads to accidents 7 Elevator servo. Install the nylon control horn and connect the linkage MX8mm cap screw MX5mm screw Mx0mm Fiberglass tube Elevator rod Elevator rod ssembly of the fuel tank

7 ccessory list for this page. ssemble the cowling to fuselage with screw.8x50mm Throttle rod Nut ( mm ) Cap screw mx Linkage Stopper Set screw ( xmm) Washer Rubber gasket plywood (mm) MXmm Cap land nut (mm) Washer MXmm Cap Rubber gasket Washer Rubber gasket ssemble the engine Trim the surplus shaded portion away from the canopy Mount the receiver and battery in the fuselage 5 ssemble the canopy to the fuselage with TP screws.8x50mm Throttle rod Linkage Stopper Nut ( mm ) Set screw ( xmm) (attery) (Receiver) Throttle servo MXmm Cap Washer Rubber gasket

8 ccessory list for this page. 8 Epoxy the wheel wells to the holes If you choose an air retractable landing gear, the installing method is as steps to 0. Epoxy the wheel wells to the holes 9 ssemble the front-wheel drive 7 ssemble of the landing gear 0 Three wheel retract system L R Strut Strut 5X5mm xletree X0mm Tp screw Strut -way pressure inlet ir inlet mm Collar -way pressure inlet ir tank ir tank Xmm screw Xmm screw Quick release connector Switch 8

9 djustment. djustment. ILERON Top view djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. 7mm 5mm djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. Top view Side view djustment. djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. Side view 0mm Centre of Gravity. Never fly before checking the Cg s required position. In order to obtain the CG specified,reposition the receiver and battery. CG Top view 0mm Warning NEVER fly the model without well balancing. 5 Spread a diagram 5 9