PARTS MANUAL SECTION 1-30

Transcription

1 2047 FRONT END LOADER Published 05/11 PARTS MANUAL SECTION 1-30 MATERIAL HANDLING PARTS MANUAL

2 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.direct any questions regarding parts to: BUSH HOG 2501 Griffin Ave. Selma, AL Contact Us Alamo Group Inc.

3

4 LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship. DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES Bush Hog s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Bush Hog. THIS LIMITED WARRANTY SHALL NOT APPLY: 1. To vendor items which carry their own warranties, such as engines, tires, and tubes. 2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability. 4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the sole judgement of Bush Hog, affects its performance, stability or reliability. 5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure. 6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the company s sole judgement is a wear item. NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND SIGNED BY BUSH HOG S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA Record the model number, serial number and date purchased. This information will be helpful to your dealer if parts or service are required. MODEL NUMBER SERIAL NUMBER DATE OF RETAIL SALE MAKE CERTAIN THE WARRANTY HAS BEEN FILED WITH BUSH HOG SELMA, ALABAMA

5 TABLE OF CONTENT 2047 FRONT END LOADER ITEM PAGE FRAMES Mainframe and Subframe A -1 MOUNTING KITS Kit Cub Aadet 7009, 7200, 7250HST, 7192,7194, B-1 Kit New Holland TC 18FWA (SNUD3366and Up), TC21D (SN UF33357 and Up), TC21DA, TC23DA, TC24D, TC24DA, TC26DAFWA B-2 Kit Cub Cadet 7252, 7254, B-3 Kit Deutz Allis B-4 Kit John Deere 655, 755, B-5 Kit John Deere B-6 Kit John Deere B-7 Kit John Deere 670, 770, B-8 Kit John Deere LB1714, LB B-9 ATTACHMENTS Bucket C-1 HYDRAULICS Hydraulic System (2407 Plumbing on RH Side) D-1 Hydraulic System (2407 Plumbing on LH Side)John Deere 655, 755, 855, 670, 770, 790 with SCV Valve D-2 Hydraulic Valve (Dukes) D-3 Hydraulic Valve (Prince LVR Parallel) D-4 Hydraulic Cylinder (Lift) D-6 Hydraulic Cylinder (Bucket) D-7 Hose Kit, New Holland TC18, TC21D, TC21DA, TC23DA, TC24DA, TC26DA, Case IHDX21, DX23, DX24, DX E-1 Hose Kit, John Deere 790 (SN AND UP) E-2 Hose Kit John Deere 655, 670, 755, 770, 790, E-4 Hose Kit John Deere 655, 670, 755, 770, 790, 855 (LH Plumbing) E-5 Hose Kit Deutz Allis 5215 SYNCRO E-6 Hose Kit Deutz Allis 5215HST E-7 Hose Kit Deutz Allis 5215 HST and SYNCRO Shift E-8 Control Valve and Plumbing Kit Case IH DX21, DX23, DX24, DX F-1 Control Valve and Plumbing Kit Case IH 1120, Cub Cadet 7000, 7200, 7250HST, 7192, 7194, F-2 Control Valve and Plumbing Kit Cub Cadet 7252, 7254, F-4 Control Valve and Plumbing Kit John Deere F-6 Control Valve and Plumbing Kit John Deere F-9 Control Valve and Plumbing Kit John Deere 670, 770, F-10 Control Valve and Plumbing Kit Kioti LB F-12 Control Valve and Plumbing Kit New Holland TC18, TC21D, TC23DA, TC24D, TC26DA F-14 GRILL GUARD Grill Guard Kit G-1 DECALS Decal Location H-1 Decal Pictorials H-2

6 NOTES:

7 2047 MAINFRAME AND SUBFRAME Boom Assembly Lock Nut, 5/ Capscrew, 5/16 X 1-3/ Fitting, Grease, 1/4-28, Straight Cylinder, Bucket Pin Assembly Lock Nut, 3/ Capscrew, 1/2 X 1-3/ Bolt, Shoulder, 3/8 X Cylinder, Boom Pin Fitting, Grease, 1/4-28, Frame, Side, Left Frame, Side, Right Channel Assembly Rod, Indicator U-Bolt Bracket Nut, 5/ Lockwasher, 5/ Flatwasher, 5/ Pin, Cotter, 1/ Hinge Assembly Decal, Operator's Manual Seal, Canister Screw, Self Tapping,.25 X Canister With Cap, Includes Item Bolt, Carriage, 5/8 X 4-1/ Nut, 5/ Bolt, Carriage, 5/8 X Flatwasher, 5/ Lock Nut, 5/ A-1

8 MOUNTING KIT Case IH 1120 Hydro Cub Cadet 7000, 7200, 7250HST, 7192, 7194, Fron t Mount Bracket Ca[pscrew 11/2-13 x 1-1/ Locknut, 1/ Flatwasher1/ Bracket, Mid Mount RH Bracket Mid Mount LH Capscrew M14-2 x Lockwasher 9/ Capscrew 5/8-11 x 1-3/ Locknut 5/ B-1

9 MOUNTING KIT Case IH DX21, DX23, DX24, and DX26FWA New Holland TC18FWA (S/N UD3366and Higher), TC21D(S/N UF33357 and Higher), TD21DA, TC23DA, TC24D, TC24DA and TC26DAFWA Mid Mount Bracket LH Mid Mount Bracket RH Mount Bracket, Front Bracket, Valve Mount Plate Spacer Capscrew M16-2 x 50 Gr Capscrew 5/8-11 x 1-1/ Capscrew 1/2-13 x 1-1/ Capscrew 1/2-13 x Lockwasher 5/ Locknut 5/ Locknut 1/ B-2

10 MOUNTING KIT Cub Cadet 7252, 7254, Mounting Bracket, Mid, Left Mounting Bracket, Mid, Right Mounting Bracket, Front Plate, Spacer Capscrew, 1/2-13 X 2.00" Capscrew, 1/2-13 X 1.50" Lockwasher, 1/2" Lock Nut, 1/ B-3

11 MOUNTING KIT Deutz-Allis Bracket, Front Mounting Plate, Frame Reinforcement, Left Plate, Frame Reinforcement, Right Bracket, Mid Mounting, Left Bracket, Mid Mounting, Right Bracket, Rear Mounting, Left Bracket, Rear Mounting, Right Bracket, Mid Crosstie Bracket, Mid Support, RH Bracket, Coolant Valve Relocation Spacer, 5/ Bolt, Carriage, 1/2-13 X 1-3/ Bolt, Carraige, 1/2-13 X 1-1/ Capscrew, 1/2-13 X 6, Grade Screw, Metric Cap, M X Screw, Metric Cap, M X Screw, Metric Cap, M X Flatwasher, 1/ Lockwasher, 1/ Lockwasher, 3/ Lock Nut, 1/ Hex Nut, 1/ Nut, Metric, M B-4

12 MOUNTING KIT JOHN DEERE 655, 755, Bracket, Front Mounting, Left Bracket, Front Mounting, Right Bracket, Mid Mounting, Left Bracket, Mid Mounting, Right Tube, Mid Cross Tie Capscrew, 1/2-13 X 3-1/ Capscrew, 1/2 X 4-1/ Capscrew, 1/2 X 1-1/ Lock Nut, 1/ B-5

13 MOUNTING KIT JOHN DEERE Front Mounting Assembly, L Front Mounting Assembly, R Plate Mid Mounting Assembly, L Mid Mounting Assembly, R Spacer Spacer Capscrew 1/2-13x2 G5 Zc Capscrew 1/2-13x1 3/4 G5 Zc Capscrew M mmx45mm Cl8.8 Pl Capscrew M mmx40mm Cl8.8 Pl Capscrew M mmx35mm Cl8.8 Pl Flatwasher 5/8 Sae Zc Flatwasher 1/2 Sae Zc Lockwasher 1/ Nut Hex Lock Type N 1/ Clevis Pin 5/8x2.50 (Zp) Pin Cotter Hair.148 X B-6

14 MOUNTING KIT JOHN DEERE Bracket, Front Left Bracket, Front Right Angle, Front Cross Tie Bracket, Mid Left Bracket, Mid Right Capscrew 1/2-13 X Capscrew 1/2-13 x 1-3/ Capscrew M x Capscrew M x Flatwasher 5/ Flatwasher 1/ Lockwasher 1/ Locknut 1/ Clevis Pin Pin, Cotter B-7

15 MOUNTING KIT JOHN DEERE 670, 770, Bracket, Mounting, Front, Left Bracket, Mounting, Front, Right Bracket, Mounting, Mid, Left Bracket, Mounting, Mid, Right Spacer, Plate, Triangular, Mid (Not Required On Tractor With Mower) Capscrew, 16mm-2.00 X 55mm, Grade Capscrew, 16mm-2.00 X 35mm, Grade Capscrew, 12mm-1.75 X 45mm, Grade Flatwasher, 5/8" Lockwasher, 5/8" Lockwasher, 1/2" Spacer, Plate, Rectangular, Front (Used For Model 790 Tractor Only) B-8

16 MOUNTING KIT JOHN DEERE LB1714 AND LB Bracket, Front Capscrew 1/2-13 x 1-1/ Locknut 1/ Flatwasher 1/2 SAE Bracket Mid Right Bracket Mid Left Capscrew M 14-2 x Lockwasher 9/ Capscrew 5/8-11 x 1-3/ Locknut 5/ B-9

17 BUCKET ASSEMBLY Bucket Assembly 48 (Order from Wholegoods) Bucket Assembly 54 (Order from Wholegoods) Side Cutting Edge Bottom Cutting Edge Bottom Cutting Edge C-1

18 HYDRAULIC SYSTEM Basic 2047 Models (Plumbing on RH Side) Clamp, Oil Line Screw, Self-Drilling, 1/4-14 X 1-1/ Hose,.250 X Hose,.250 X Hose,.250 X Clamp, Hose Tube, Oil Line Clamp, Oil Line Tube, Oil Line Screw, Self-Drilling, 1/4-14 X 1-1/ D-1

19 HYDRAULIC SYSTEM 2047 Models (Plumbing on LH Side) JOHN DEERE 655, 755, 855, 670, 770, 790 WITH SCV VALVE Clamp, Oil Line Screw, Self-Drilling, 1/4-14 X 1-1/ Hose,.250 X Hose,.250 X Hose,.250 X Clamp, Hose Tube, Oil Line Clamp, Oil Line Tube, Oil Line Screw, Self-Drilling, 1/4-14 X 1-1/

20 HYDRAULIC VALVE DUKES Control Valve Assy. (Dukes) Repair Kit, Seal - Pilot Operated Relief Repair Kit, Pilot Operated Relief Repair Kit, Load Check Repair Kit, Spring Centering Repair Kit, Detent Spring Centering Plate, 1-Way Restrictor W/.109 Hole Power Beyond Kit D-3

21 HYDRAULIC VALVE PRINCE (LVR Parallel Valve) D-4

22 HYDRAULIC VALVE PRINCE (LVR Parallel Valve) Seal Kit Power Beyond Sleeve Relief Cartridge (2000 PSI) Relief Cartridge (1600 PSI) Float Kit, (Includes 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, And 26) Regen Kit, (Includes Items 12, 13, 14, 15, 16, 17, 19, 20, 21, 24, And 26) Boot, Rubber, Valve Handle Stud, Spool Adapter Plate Rod End Rod End, Assembly Clevis End Cap (Manufacturer s Part Number (Hc-V-Aa26) Stamped On End Cap Identifies Valve And Relief Setting) Capscrew,Socket Head, 1/4-20 X 1/ Plug, Load Check Hex Nut, 5/ Capscrew, Socket Head, 1/4-20 X 7/ Plate Washer, Shim, 5/ G Hex Nut, 7/ End, Spool Handle, Valve, Standard Ball, Handle Capscrew, Socket Head, 5/16-24 X 3/ G Lockwasher, 7/ Valve Assembly (1600 PSI Relief) Valve Assembly (2000 PSI Relief) D-5

23 HYDRAULIC CYLINDER - LIFT Cylinder Assy. (Lift) Shaft, Cylinder 1 2 * Seal, Wiper 1 3 * Seal, U-Cup 1 4 * Wear Ring Head, Cylinder 1 6 * Washer, Backup 1 7 * O-Ring 1 8 * Wear Ring Piston 1 10 * O-Ring 1 11 * Seal, Piston c Lock Nut, 3/ Tube, Cylinder 1 14 * Wire, Retaining Repair Kit, (* Parts In Kit) D-6

24 HYDRAULIC CYLINDER - BUCKET Bucket Cylinder Assembly Shaft, Cylinder 1 2 * Seal, Wiper 1 3 * Seal, U-Cup 1 4 * Wear Ring Head, Cylinder 1 6 * Washer, Backup 1 7 * O-Ring 1 8 * Wear Ring Piston 1 10 * O-Ring 1 11 * Seal, Piston c Lock Nut, 3/ Tube, Cylinder 1 14 * Wire, Retaining Repair Kit, (* Parts In Kit) D-7

25 HOSE KIT NEW HOLLAND TC18, TC21D,TC21DA, TC 23DA, TC24DA, TC26DA CASE IH DX21, DX23, DX24,DX Hose, 1/4 X 54, 9/16-18 JIC Female Swivel X 9/16-18 JIC Female Swivel Sleeve, Hose, Nylon, 1-1/4 X 2 X Fitting, Elbow, 90, 9/16-18 JIC Male X 9/16-18 O-Ring Male Fitting, Elbow, 90, Long, 9/16-18 JIC Male X 9/16-18 O-Ring Male Spiral Band, Blue 5/ Spiral Band, Red, 5/ Spiral Band, Yellow, 5/ Spiral Band, Green, 5/ Coupler, Quick, Male Tarp Strap E-1

26 HOSE KIT JOHN DEERE Model 790 sn and higher 1-30E-2

27 HOSE KIT JOHN DEERE Model 790 sn and higher Hose, 1/4 X 60" Sleeve, Nylon, 1.59 X 47.0" Tarp Strap Spiral Band, 5/8, (Red) Spiral Band, 5/8, (Yellow) Spiral Band, 5/8, (Green) Spiral Band, 5/8, (Black) Quick Coupler, Male E-3

28 HOSE KIT JOHN DEERE Model 655, 670, 755, 770, 790, Hose, 1/4 X 120" Tie Strap Band, Silver Band, Yellow Band, Black Band, Green E-4

29 HOSE KIT JOHN DEERE Model 655, 670, 755, 770, 790 (Prior to S/N 790,000), Hose 1/4 x Tie Strap Band, Silver Band, Yellow Band, Black Band, Green Sleeve, Nylon 1.59 x E-5

30 HOSE KIT DEUTZ-ALLIS 5215 SYNCRO SHIFT Plate, Lever Mount Lever Assembly, Dual Linkage, Valve Spool Pin, Clevis 3/16 x 7/8 6 5 G Pin, Cotter 3/32 x 1/ Tip, Rubber Decal, Remote Decal, Remote w/ Float Capscrew M x Capscrew M x G Lockwasher 7/ G Capscrew 1/4-20 x 1-1/ G Lockwasher 1/ G Flatwasher 1/ G Hex Nut 1/ Fitting Straight 9/16 JIC x 3/8 BSPP Fitting Elbow 9/16 JIC x 3/8 BSPP Fitting Elbow 9/16 JIC x 9/16 JIC Hose 1/4 x Coupler, Female Quick Band, Spiral Blue Band, Spiral Red Band, Spiral Yellow Band, Spirol Green Plug, Dust E-6

31 HOSE KIT DEUTZ-ALLIS 5215 HST Lever Assy Capscrew M x G Lockwasher 5/ G Flatwasher 5/ Tip, Rubber Linkage, Rod Linkage, Rod Pin, Clevis 3/16 x 7/8 4 9 G Pin, Cotter 3/32 x Decal, Remote Decal, Remote w/ Float Position Fitting, Elbow 3/8 BSPP x 9/16 JIC Fitting, Straight 3/8 BSPP x 9/16 JIC Fitting, Elbow 9/16 JIC x 9/16 JIC Hose 1/4 x Coupler, Female Plug, Dust Band, Spiral Blue Band, Spiral Red Band, Spiral Yellow Band, Spiral Green E-7

32 HOSE KIT DEUTZ-ALLIS 5215 HST and Synchro Shift Hose, 1/4 X 102" Coupler, Male Band, Blue Band, Red Band, Yellow Band, Green Strap, Adjustable Strap, Rubber E-8

33 CONTROL VALVE AND PLUMBING KIT CASE IH DX21, DX23, DX24, DX Valve, Prince LVR (2000 Psi) Capscrew, 3/8-16 X 2-1/ Handle, Valve, Standard Angle, Decal Mounting Lock Nut, 3/ Capscrew, 5/16-18 X 3/ Lockwasher, 5/ Ball, Valve Handle Elbow, 3/4-16 JIC X 3/4-16 O-Ring, Hose, 3/8 X 36 (Pressure & Tank) Flatwasher, 1/ Hose, 3/8 X 38 (Power Beyond) Hex Nut, 7/ Boot Coupler, Female Spiral Band, Plastic, Blue, Spiral Band, Plastic, Red, Spiral Band, Plastic, Yellow, Spiral Band, Plastic, Green, Hose, 1/4 X Spiral Band, Plastic, Blue, 5/ Spiral Band, Plastic, Red, 5/ Spiral Band, Plastic, Yellow, 5/ Spiral Band, Plastic, Green, 5/ Coupler, Male Decal, Single Handle Control Strap, Adjustable Fitting, Adapter, 3/4-16 O-Ring X 3/8 Npt Plate, Valve Mounting Tube, Valve Mounting Sleeve, Nylon, Elbow, 3/8 NPT M X 3/4-16 Jic M, Elbow, 3/4-16 JIC F S X 3/4-16 JIC M, Capscrew, 1/2-13 X 2-1/ Lock Nut, 1/ F-1

34 CONTROL VALVE AND PLUMBING KIT CASE IH 1120 and Cub Cadet 7000, 7200, 7205 HST, 7192, 7194 & F-2

35 CONTROL VALVE AND PLUMBING KIT CASE IH 1120 and Cub Cadet 7000, 7200, 7205 HST, 7192, 7194 & Valve, Dukes P/N 1627-Ft Linkage-Bracket Flt Soc. Scrw 5/16-24 X 3/ Socket Hd Capscrew 5/16-24 X Handle Assy Zp Rod End 1/4-28 Ydp Rod End,Ball Joint 1/4-28 Ydp Stud (Rod End) Ydp Soc Hd Capscrew 1/4-28 X Flatwasher 1/4 Sae Lockwasher 1/ Nut Hex 1/4-28 Zc Lock Nut 1/ Fitting, Power Beyound Adp Hyd Elbow 6mj - 6mb90 Ydp Hose 3/8 X 6.88 Lg Hose 3/8 X 7.88 Lg Hose 3/8 X 8.50 Lg Hose 3/8 X Lg Hose 3/8 X 44" (Sae100r1) Hose 3/8 X 44" (Sae100r1) Spacer, Black Valve Box Assembly Cover Capscrew, 1/4-20x2 G5 Zc Nut Hex Lock Type N 1/ J" Clip Screw #10-16 X 1/2 Typ Ab,Pan Hd Coupler Body-Female Spiral Band,Plastic-Red- 1" Id Spiral Band,Plastic-Yel-1" Id Spiral Band,Plastic-Green-1"Id Spiral Band,Plastic-Blue-1" Id Boot-Black (Dukes# ) Cap Nut (Arden#C ) Ball-Handle (Davies #35k) Tube, Valve Mount Capscrew, 1/2-13 X 2-1/ Flatwasher, 1/ Locknut 1/ Capscrew 3/8-16 X 2-1/ Locknut 3/ Decal, Single Handle Control Fitting 3/8-19t Iso To 3/ Adaptor, Elbow, 3/8x3/ Strap-Adjust.19 X B Tarp Strap 22" Reach Nylon Sleeve (1.59 Id X 66") Coupling Body-Male Ydp Spiral Band,Plastic-Blue.62id Spiral Band-Plast-Red-.62 I.D Spiral Band-Plast-Yel-.62.I.D Spiral Band-Plast-Grn-.62.I Hose, 1/4 X 60 Long F-3

36 CONTROL VALVE AND PLUMBING KIT CUB CADET 7252, 7254, F-4

37 CONTROL VALVE AND PLUMBING KIT CUB CADET 7252, 7254, Valve, Prince Lvr (1600 Psi) Capscrew, 3/8-16 X 2-1/ Handle, Valve, Standard Angle, Decal Mounting Lock Nut, 3/ Capscrew, 5/16-18 X 3/ Lockwasher, 5/ Ball, Valve Handle Fitting, Elbow, 9/16-18 Jic X 3/4-16 O-Ring, Hose, 3/8 X 70, 3/4-16 O-Ring X 9/16-18 Jic Swivel (Pressure & Tank) Screw, 3/8-16 X 2-1/ Hose, 3/8 X 62, 9/16 Jic Swivel X 9/16 Jic Swivel (Power Beyond) Hex Nut, 7/ Boot, Valve Handle Coupler, Female Spiral Band, Plastic, Blue, Spiral Band, Plastic, Red, Spiral Band, Plastic, Yellow, Spiral Band, Plastic, Green, Hose, 1/4 X 60, 3/8 N.P.T.F. X 9/16-18 Jic Swivel Spiral Band, Plastic, Blue, 5/ Spiral Band, Plastic, Red, 5/ Spiral Band, Plastic, Yellow, 5/ Spiral Band, Plastic, Green, 5/ Coupler, Male Decal, Single Handle Control Strap, Adjustable Fitting, Adapter, 3/4-16 O-Ring X 3/8 Npt Plate, Valve Mounting Lock Nut, 1/ Fitting, Adapter, 9/16-18 Jic X 3/4-16 Sae O-Ring Tarp Strap Fitting, Adapter, 9/16-18 Jic X 7/8-14 Sae O-Ring Tube, Valve Mount Fitting, Elbow, 9/16-18 Jic X 9/16-18 Jic, Sleeve, Hose, 1.59 Id X Sleeve, Hose, 1.59 Id X Sleeve, Hose, 1 Id X F5

38 CONTROL VALVE AND PLUMBING KIT JOHN DEERE F-6

39 CONTROL VALVE AND PLUMBING KIT JOHN DEERE Valve, Dukes Linkage-Bracket Flat Soc. Scrw 5/16-24x Socket Hd Screw 5/16-24 X Handle Assy Rod End,Ball Joint 1/ Rod End 1/4-28 Female Stud (Rod End) Socket Hd Screw 1/4-28 X Flatwashert 1/4 Sae Lockwasher 1/ Nut Hex 1/4-28 Zc Locknut Type N1/4-28cd(Fs Fitting, Power Beyond Sleeve Adp Hyd Elbow 6mj - 6mb90 Ydp Hose 3/8 x6.88 Lg Hose 3/8 x7.88 Lg Hose 3/8 x8.50 Lg Hose 3/8 x13.00 Lg Hose.375 x 72" Long SAE Hose,3/8 x78 (Sae100r1) Hose.375 Id x SAE Capscrew, 1/4-20 x 2 G Locknut Type N 1/ Valve Box Assembly Cover J" Clip 2 28 G Scrw#10-16 x1/2 Pan Hd Spacer,(Rodon #Hw-1)Black Coupler Body-Female Spiral Band,Plastic-Blue-1" Id Spiral Band,Plastic-Red- 1" Id Spiral Band,Plastic-Yel-1" Id Spiral Band,Plastic-Green-1"Id Boot-Black (Dukes# ) Cap Nut(Arden#C ) Ball-Handle (Davies #35k) Tube, Valve Mount Capscrew, 1/2-13x2 1/2 G5 Zc Flatwasher 1/2 Sae Zc Locknut Type N 1/ Capscrew, 3/8-16x2 1/4 G5 Zc LccknutT Type N 3/ Decal, Single Handle Control 1 42 G Ftg Plug H Soc 1/ Adaptor, 9/16-18x3/4-16 Ydp Adp Hyd Elbow 6mj-6fjx Adp Hyd Elbow 6mj - 8mb Strap-Adjust.19 X B Hose.25 X 60 Sae 100r Spiral Band,Plastic-Blue.62id Spiral Band-Plast-Red-.62 I.D Spiral Band-Plast-Yel-.62.I.D Spiral Band-Plast-Grn-.62.I Nylon Sleeve(1.59 Id X 66") Coupler, Male Quick Tarp Strap 22" Reach F-7

40 CONTROL VALVE AND PLUMBING KIT JOHN DEERE F-8

41 CONTROL VALVE AND PLUMBING KIT JOHN DEERE 650 Ref. Part Description Qty. No. No. Req d Valve, Prince LVR (2000 Psi) Capscrew, 3/8-16 X 2-1/ Handle, Standard Angle, Decal Mounting Locknut, 3/ Capscrew, 5/16-18 X 3/ Lockwasher, 5/ Ball, Handle Fitting, Elbow, 9/16-18 Jic X 3/4-16 O-Ring, Hose, 3/8 X 78 (Tank) Hose, 3/8 X 76 (Pressure & Power Beyond) 2 12 G Plug, 1/ Hex Nut, 7/ Boot Coupler, Female Spiral Band, Plastic, Blue, Spiral Band, Plastic, Red, Spiral Band, Plastic, Yellow, Spiral Band, Plastic, Green, Hose, 1/4 X Spiral Band, Plastic, Blue, 5/ Spiral Band, Plastic, Red, 5/ Spiral Band, Plastic, Yellow, 5/ Spiral Band, Plastic, Green, 5/ Coupler, Male Decal, Single Handle Control Strap, Adjustable Fitting, Adapter, 3/4-16 O-Ring X 3/8 Npt Plate, Valve Mounting Bracket, Valve Mounting Sleeve, Nylon Tarp Strap Locknut, ½ Flatwasher, 1/ Capscrew, 1/2-13 X 2-1/ Fitting, Elbow, 9/16 Jic X 9/16 Jic Swivel, F-9

42 CONTROL VALVE AND PLUMBING KIT JOHN DEERE 670,770, F-10

43 CONTROL VALVE AND PLUMBING KIT JOHN DEERE 670,770, 790 Ref. Part Description Qty. No. No. Req d Valve, Dukes P/N 1627-Fs Linkage-Bracket(Zp) Flat Socket Hd Capscrew 5/16-24x.75 (Fs) Socket Hd Capscrew 5/16-24 X 0.75 (Fs) Handle Assy Zp Rod End 1/4-28 Ydp Rod End,Ball Joint 1/4-28 Ydp Stud (Rod End) Ydp Socket Hd Capscrew 1/4-28 X Flatwasher 1/4 Sae Zc Lockwasher 1/4 Zc Nut Hex 1/4-28 Zc Nut Hex Lock Type N1/4-28cd(Fs Fitting, Power Beyond Sleeve Adp Hyd Elbow 6mj - 6mb90 Ydp Hose 3/8x6.88 Lg Hose 3/8x7.88 Lg Hose 3/8x8.50 Lg Hose 3/8x13.00 Lg Hose.375 X 72" Long Sae100r Hose, 3/8 X 60 (Sae 100r1) Hose.375 Id X Sae100r Capscrew, 1/4-20x2 G5 Zc Nut Hex Lock Type N 1/ Valve Box Assembly Cover J" Clip Scrw#10-16x1/2typ Ab,Pan Hd(Fs Spacer,(Rodon #Hw-1)Black Coupler Body-Female Ydp Spiral Band,Plastic-Red- 1" Id Spiral Band,Plastic-Yel-1" Id Spiral Band,Plastic-Green-1"Id Spiral Band,Plastic-Blue-1" Id Boot-Black (Dukes# ) Cap Nut(Arden#C ) Ball-Handle (Davies #35k) Tube, Valve Mount Capscrew, 1/2-13x2 1/2 G5 Zc Flatwasher 1/2 Sae Zc Nut Hex Lock Type N 1/ Capscrew, 3/8-16x2 1/4 G5 Zc Nut Hex Lock Type N 3/ Decal,Single Handle Control 1 42 G Ftg Plug H Soc 1/4-18 S Adp Hyd Elbow 6mj - 8mb90 Ydp Adaptor, 9/16-18x3/4-16 Ydp Elbow 6mj - 6fjx45 Ydp Adp Hyd Elbow 6mj-6fjx -90dg Strap-Adjust.19 X B Hose.25 X 66 Sae 100r Spiral Band,Plastic-Blue.62id Spiral Band-Plast-Red-.62 I.D Spiral Band-Plast-Yel-.62.I.D Spiral Band-Plast-Grn-.62.I Nylon Sleeve(1.59 Id X 66") Coupling Body-Male Ydp Tarp Strap 22" Reach F-11

44 CONTROL VALVE AND PLUMBING KIT Kioti LB1714, LB F-12

45 CONTROL VALVE AND PLUMBING KIT Kioti LB1714, LB1914 Ref. Part Description Qty. No. No. Req d Valve, Prince LVR (2000 PSI) Capscrew, 3/8-16 X 2-1/ Handle, Standard Angle, Decal Mounting Locknut, 3/ Capscrew, 5/16-18 X 3/ Lockwasher, 5/ Ball, Handle Fitting, Elbow, 9/16-18 Jic X 3/4-16 O-Ring, Hose, 3/8 X Locknut, 1/ Fitting, Adapter, 9/ Hex Nut, 7/ Boot Coupler, Female Spiral Band, Plastic, Blue, Spiral Band, Plastic, Red, Spiral Band, Plastic, Yellow, Spiral Band, Plastic, Green, Hose, 1/4 X Spiral Band, Plastic, Blue, 5/ Spiral Band, Plastic, Red, 5/ Spiral Band, Plastic, Yellow, 5/ Spiral Band, Plastic, Green, 5/ Coupler, Male Decal, Single Handle Control Strap, Adjustable Fitting, Adapter, 3/4-16 O-Ring X 3/8 Npt Plate, Valve Mounting Bracket, Valve Mounting Sleeve, Nylon Tarp Strap Fitting, 9/16-18 X 3/ Fitting, Elbow, 9/16-18 X 9/16-18, Flow Bolt Flow Bolt 3 31 ** Copper Seal 3 32 ** O-Ring 3 33 G Flatwasher, 1/ Capscrew, 1/2-13 X 2-3/ Seal Kit, Flow Bolt (Contains Replacement Copper Rings And O-Rings) Orifice Restrictor Kit (.094 Dia.) F-13

46 CONTROL VALVE AND PLUMBING KIT New Holland TC18D (S/N UD33666 and UP), TC21D and TC24D (S/N UF33557 and Up), TC23DA and TC26DA 1-30F-14

47 CONTROL VALVE AND PLUMBING KIT New Holland TC18D (S/N UD33666 and UP), TC21D and TC24D (S/N UF33557 and Up), TC23DA and TC26DA Ref. Part Description Qty. No. No. Req d Valve, Prince Lvr (2000 Psi) Capscrew, 3/8-16 X 2-1/ Handle, Valve, Standard Angle, Decal Mounting Locknut, 3/ Capscrew, 5/16-18 X 3/ Lockwasher, 5/ Ball, Valve Handle Fitting, Elbow, 3/4-16 Jic X 3/4-16 O-Ring, Hose, 3/8 X 36 (Pressure & Tank) Flatwasher, 1/ Hose, 3/8 X 38 (Power Beyond) Hexnut, 7/ Boot Coupler, Female Spiral Band, Plastic, Blue, Spiral Band, Plastic, Red, Spiral Band, Plastic, Yellow, Spiral Band, Plastic, Green, Hose, 1/4 X Spiral Band, Plastic, Blue, 5/ Spiral Band, Plastic, Red, 5/ Spiral Band, Plastic, Yellow, 5/ Spiral Band, Plastic, Green, 5/ Coupler, Male Decal, Single Handle Control Strap, Adjustable Fitting, Adapter, 3/4-16 O-Ring X 3/8 Npt Plate, Valve Mounting Tube, Valve Mounting Sleeve, Nylon, Fitting, Elbow, 3/8 Npt Male X 3/4-16 Jic Male, Fitting, Elbow, 3/4-16 Jic Female Swivel X 3/4-16 Jic Male, Capscrew, 1/2-13 X 2-1/ Locknut, 1/ F-15

48 GRILL GUARD KIT Ref. Part Description Qty. No. No. Req d Grille Guard, 2406 & 2406s, Loader Bumper Style Screw, Cap, 3/8-16 X 1-1/2", Grade Nut, Lock, 3/8-16, Type N G-1

49 DECALS Logo Decal Bush Hog Model Warning Oil Leaks Warning Lock Valve In Transport Instruction Loader Positions 1 6 D469 Warning Loader Safety 1 7 D468 Danger Crushing, Electrocution, Falling Hazard 2 8 D471 Warning Handling Bales 1 9 D470 Danger Use Rops, Seatbelt, Rear Ballast Reflector SMV Sign Canister, Operator s Manual Operators Manual (2047 Loader) H-1

50 DECALS Logo Decal Bush Hog Model Warning Oil Leaks Warning Lock Valve In Transport Instruction Loader Positions 1 6 D469 Warning Loader Safety 1 7 D468 Danger Crushing, Electrocution, Falling Hazard 2 8 D471 Warning Handling Bales 1 9 D470 Danger Use Rops, Seatbelt, Rear Ballast H-2

51 2501 Griffin Ave. Selma, AL (334) (334) Parts Ordering Fax